Rip out the existing powerpc msi stubs. These were the start of an
implementation based on ppc_md calls, but were never used in mainline.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For 32-bit systems, powerpc still relies on the 4level-fixup.h hack,
to pretend that the generic pagetable handling stuff is 3-levels
rather than 4. This patch removes this, instead using the newer
pgtable-nopmd.h to handle the elision of both the pud and pmd
pagetable levels (ppc32 pagetables are actually 2 levels).
This removes a little extraneous code, and makes it more easily
compared to the 64-bit pagetable code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Generalize tsi108_setup_pci to take the config space physical address and
primary bus designator as a parameter.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a phy_type field to the tsi108 ethernet structures to indicate which PHY
is used on a board. This is derived from the "compatible" property in the
ethernet-phy node of the device tree. The default remains the MV88E PHY.
Also, convert the setup code to use of_get_mac_address instead of hard coding
a lookup for the "address" property in the ethernet node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a header file for the common PCI routines used for the TSI bridge
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently other parts of the kernel need to know the
modalias internally (like the sysfs code in macintosh driver).
To avoid consistency issues, we export this code and use it
everywhere it's needed rather than repeat it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit powerpc uses a PTE_FMT macro to handle printk() formatting of
PTE entries (which can vary in type and size). Apparently there was a
good reason for it once, but with current compilers it's simpler just
to workaround the variation with a cast in the printk() itself
(there's only one use).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements save and restore hooks for IOMMUs and implements
it the DART iommu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av:
- Move the definition of struct ps3av to ps3av.c, as it's locally used only.
- Kill ps3av.sem, use the existing ps3av.mutex instead.
- Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
Its use is protected by a semaphore anyway.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add hooks to allow a paravirt implementation to track the lifetime of
an mm. Paravirtualization requires three hooks, but only two are
needed in common code. They are:
arch_dup_mmap, which is called when a new mmap is created at fork
arch_exit_mmap, which is called when the last process reference to an
mm is dropped, which typically happens on exit and exec.
The third hook is activate_mm, which is called from the arch-specific
activate_mm() macro/function, and so doesn't need stub versions for
other architectures. It's called when an mm is first used.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: linux-arch@vger.kernel.org
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Call the kprobes pagefault handler directly instead of going through
the complex notifier chain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When data symbols are not present in kernel image, user needs to add
dot(".") before function name explicitly, that he wants to probe in kprobe
module on ppc64.
for ex:-
When data symbols are missing on ppc64,
====================
[root@llm27lp1 ~]# cat /proc/kallsyms | grep do_fork
c00000000006283c T .do_fork
==============================
User needs add "." to "do_fork"
kp.symbol_name = ".do_fork";
============================
This makes kprobe modules unportable. This fixes the problem.
Signed-off-by: Srinivasa Ds <srinivasa@in.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all 32-bit powerpc platforms use asm-ppc/pgtable.h and
asm-ppc/pgalloc.h, even when otherwise compiled with ARCH=powerpc.
Those asm-ppc files are a fairly nasty tangle of #ifdefs including a
bunch of things which shouldn't be necessary any more in arch/powerpc.
Cleaning up that mess is going to take a while, but this patch is a
first step. It separates the asm-powerpc/pg{alloc,table}.h into 64
bit and 32 bit versions in asm-powerpc, which the basic .h files in
asm-powerpc select based on config. We make a few tiny tweaks to the
innards of the files along the way, making the outermost ifdefs
(double-inclusion protection and __KERNEL__) a little cleaner, and
#including asm-generic/pgtable.h from the top-level
asm-powerpc/pgtable.h (since both the old 32-bit and 64-bit versions
ended with such an #include).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't have it active by default, the STRICT_MM_TYPECHECKS
option has bitrotted again. This patch fixes a couple of simple build
fixes if the option is selected. First, pud_t mustn't be defined in
page.h on 32-bit systems, because it conflicts with the version in the
generic pud-folding code. Second, pci_32.c is missing a __pgprot()
wrapper call. Third, a couple of PS3 files use constants of type
pgprot_t when they need the raw values, we add pgprot_val() calls to
fix this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch takes the definitions for the PPC44x MMU (a software loaded
TLB) from asm-ppc/mmu.h, cleans them up of things no longer necessary
in arch/powerpc and puts them in a new asm-powerpc/mmu_44x.h file. It
also substantially simplifies arch/powerpc/mm/44x_mmu.c and makes a
couple of small fixes necessary for the 44x MMU code to build and work
properly in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no big reason to have that function inlined.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the powerpc architecture, of_irq_to_resource, currently sitting in
prom.h, needs irq_of_parse_and_map and NO_IRQ from asm-powerpc/irq.h.
The solution suggested by Benjamin Herrenschmidt is to move it to
arch/powerpc/kernel/prom_parse.c.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes sure that a caller of pmac_call_feature() won't try
to call into ppc_md.feature_call of another platform, which might
happen if some powermac drivers are loaded on non-powermac machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch puts enable_kernel_spe into <asm-powerpc/system.h> along with
enable_kernel_altivec etc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently asm-powerpc/mmu.h has definitions for the 64-bit hash based
MMU. If CONFIG_PPC64 is not set, it instead includes asm-ppc/mmu.h
which contains a particularly horrible mess of #ifdefs giving the
definitions for all the various 32-bit MMUs.
It would be nice to have the low level definitions for each MMU type
neatly in their own separate files. It would also be good to wean
arch/powerpc off dependence on the old asm-ppc/mmu.h.
This patch makes a start on such a cleanup by moving the definitions
for the 64-bit hash MMU to their own file, asm-powerpc/mmu_hash64.h.
Definitions for the other MMUs still all come from asm-ppc/mmu.h,
however each MMU type can now be one-by-one moved over to their own
file, in the process cleaning them up stripping them of cruft no
longer necessary in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an old interface and is replaced by of_find_compatible_node.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
BenH's commit a741e67969 in powerpc.git,
although (AFAICT) only intended to affect ppc64, also has side-effects
which break 44x. I think 40x, 8xx and Freescale Book E are also
affected, though I haven't tested them.
The problem lies in unconditionally removing flush_tlb_pending() from
the versions of flush_tlb_mm(), flush_tlb_range() and
flush_tlb_kernel_range() used on ppc64 - which are also used the
embedded platforms mentioned above.
The patch below cleans up the convoluted #ifdef logic in tlbflush.h,
in the process restoring the necessary flushes for the software TLB
platforms. There are three sets of definitions for the flushing
hooks: the software TLB versions (revised to avoid using names which
appear to related to TLB batching), the 32-bit hash based versions
(external functions) amd the 64-bit hash based versions (which
implement batching).
It also moves the declaration of update_mmu_cache() to always be in
tlbflush.h (previously it was in tlbflush.h except for PPC64, where it
was in pgtable.h).
Booted on Ebony (440GP) and compiled for 64-bit and 32-bit
multiplatform.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save the trap number in the case of getting a bad stack in an exception
handler. It is sometimes useful to know what exception it was that caused
this to happen. Without this, no trap number is reported.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a driver to arch/powerpc/sysdev for the UIC, the
on-chip interrupt controller from IBM/AMCC 4xx chips. It uses the new
irq host mapping infrastructure.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For cases when probes are placed on instructions that can be emulated,
don't take the single-step exception.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oprofile support for PA6T, kernel side.
Also rename the PA6T_SPRN.* defines to SPRN_PA6T.*.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC 750CL has high BATs. The patch below adds a CPU_FTRS_750CL that
includes that. Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.
It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The of_iomap function maps memory for a given
device_node and returns a pointer to that memory.
This is used at some places, so it makes sense to
a seperate function.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Trivial change to pass vmsplice arguments through the compat layer on
pp64.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's an implementation of DEBUG_PAGEALLOC for ppc32. It disables BAT
mapping and is only tested with Hash table based processor though it
shouldn't be too hard to adapt it to others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/Kconfig.debug | 9 ++++++
arch/powerpc/mm/init_32.c | 4 +++
arch/powerpc/mm/pgtable_32.c | 52 +++++++++++++++++++++++++++++++++++++++
arch/powerpc/mm/ppc_mmu_32.c | 4 ++-
include/asm-powerpc/cacheflush.h | 6 ++++
5 files changed, 74 insertions(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current tlb flush code on powerpc 64 bits has a subtle race since we
lost the page table lock due to the possible faulting in of new PTEs
after a previous one has been removed but before the corresponding hash
entry has been evicted, which can leads to all sort of fatal problems.
This patch reworks the batch code completely. It doesn't use the mmu_gather
stuff anymore. Instead, we use the lazy mmu hooks that were added by the
paravirt code. They have the nice property that the enter/leave lazy mmu
mode pair is always fully contained by the PTE lock for a given range
of PTEs. Thus we can guarantee that all batches are flushed on a given
CPU before it drops that lock.
We also generalize batching for any PTE update that require a flush.
Batching is now enabled on a CPU by arch_enter_lazy_mmu_mode() and
disabled by arch_leave_lazy_mmu_mode(). The code epects that this is
always contained within a PTE lock section so no preemption can happen
and no PTE insertion in that range from another CPU. When batching
is enabled on a CPU, every PTE updates that need a hash flush will
use the batch for that flush.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Those are needed by things like alignment exception fixup handlers
since those can now be triggered by copy_tofrom_user_inatomic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers have resources that they want to be able to map into
userspace that are 4k in size. On a kernel configured with 64k pages
we currently end up mapping the 4k we want plus another 60k of
physical address space, which could contain anything. This can
introduce security problems, for example in the case of an infiniband
adaptor where the other 60k could contain registers that some other
program is using for its communications.
This patch adds a new function, remap_4k_pfn, which drivers can use to
map a single 4k page to userspace regardless of whether the kernel is
using a 4k or a 64k page size. Like remap_pfn_range, it would
typically be called in a driver's mmap function. It only maps a
single 4k page, which on a 64k page kernel appears replicated 16 times
throughout a 64k page. On a 4k page kernel it reduces to a call to
remap_pfn_range.
The way this works on a 64k kernel is that a new bit, _PAGE_4K_PFN,
gets set on the linux PTE. This alters the way that __hash_page_4K
computes the real address to put in the HPTE. The RPN field of the
linux PTE becomes the 4k RPN directly rather than being interpreted as
a 64k RPN. Since the RPN field is 32 bits, this means that physical
addresses being mapped with remap_4k_pfn have to be below 2^44,
i.e. 0x100000000000.
The patch also factors out the code in arch/powerpc/mm/hash_utils_64.c
that deals with demoting a process to use 4k pages into one function
that gets called in the various different places where we need to do
that. There were some discrepancies between exactly what was done in
the various places, such as a call to spu_flush_all_slbs in one case
but not in others.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a device_is_compatible define for compatibility during the
change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a get_property define for compatibility during the change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors. It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This common uevent handler allow the several bus types based on
of_device to generate the uevent properly and avoiding
code duplication.
This handlers take a struct device as argument and can therefore
be used as the uevent call directly if no special treatment is
needed for the bus.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The definition of struct ucc_slow puts the guemr register immediately after the
utpt register, when it should be at offset 0x90. This patch adds the missing
0x52-byte padding.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove last_syscall from 32bit powerpc, its been gone in 64bit for years.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Modify routine that returns PCI slot status to wait for slot status
to become available. This is needed, as slots that are in some remote
card cage may go offline for extended periods of time. New users for
this routine in following patches.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kexec invokes plpar_hcall hypervisor call in real mode. plpar_hcall
refers to per cpu variables for accounting hypervisor statistics.
These variables may not be in the RMO region, so accesses to them
in real mode may result in a data storage exception.
This fixes this problem by using a new plpar_hcall_raw function which
does not update the hypervisor call statistics. Thanks to Anton for
suggesting this idea.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the slb_shadow_ptr field into the first cache line since it is
(like everything there) read-only after boot. It is in fact statically
initialised and thereafter only read.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates booting-without-of.txt to describe version 17 of
the flattened device tree format. Version 17 is a small, backwards
compatible change from version 16, adding an extra field giving the
size of the device tree's structure block. At this time, the kernel
has no use for the extra information, however its presence can make
life easier for bootloaders or other software manipulating the tree.
In addition this patch adds information on the size_dt_strings field
of the device tree header, present since version 3 of the flattened
tree format, but omitted from the documentation. It also makes
changes to consistently refer to versions 16 and 17 as versions 16 and
17 in decimal, rather than version 0x10 which was occasionally used
for version 16 previously.
Finally, we also add the new field to the definition of the device
tree header structure in prom.h
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds two sysfs attributes to /sys/bus/ibmebus which can be used to
notify the ebus driver of added / removed ebus devices in the OF device
tree.
Echoing the device's location code (as found in the OFDT "ibm,loc-code"
property) into the "probe" attribute will notify ebus of addition of the
device and cause the appropriate device driver's probe function to be called
on the device.
Likewise, echoing the location code into the "remove" attribute will cause
the device to be removed from the system.
The writes will block until the respective operation has finished and return
an error code if the operation failed.
In addition, two minor tidbits are fixed:
- The fake root device used to provide a common parent for all ebus devices
is now based on device instead of of_device - it had no associated devtree
node. This saves several checks throughout the ebus driver.
- The sysfs attributes are now generated automagically by device_register()
instead of by the ibmebus code, which saves a few compiler warnings about
unused return codes.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I forgot to do this when wiring up the syscall.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code doesn't properly invalidate SPUs SLBs when necessary,
for example when changing a segment size from the hugetlbfs code. In
addition, it saves and restores the SLB content on context switches
which makes it harder to properly handle those invalidations.
This patch removes the saving & restoring for now, something more
efficient might be found later on. It also adds a spu_flush_all_slbs(mm)
that can be used by the core mm code to flush the SLBs of all SPEs that
are running a given mm at the time of the flush.
In order to do that, it adds a spinlock to the list of all SPEs and move
some bits & pieces from spufs to spu_base.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implements the per arch atomic_scrub() that EDAC uses for software
ECC scrubbing. It reads memory and then writes back the original
value, allowing the hardware to detect and correct memory errors.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I forgot to do this when wiring up the syscall.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In file included from include/asm/pci.h:20,
from include/linux/pci.h:751,
from arch/powerpc/sysdev/dart_iommu.c:36:
include/asm/prom.h: In function `of_irq_to_resource':
include/asm/prom.h:341: warning: implicit declaration of function `irq_of_parse_and_map'
include/asm/prom.h:345: error: `NO_IRQ' undeclared (first use in this function)
include/asm/prom.h:345: error: (Each undeclared identifier is reported only once
include/asm/prom.h:345: error: for each function it appears in.)
Seems that prom.h has always wanted irq.h.
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared. The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.
Remove the associated per_cpu_gain variable in sched_domains used only by
this code.
Also:
The reason is that with dynticks enabled, this code breaks without yet
further tweaks so dynticks brought on the rapid demise of this code. So
either we tweak this code or kill it off entirely. It was Ingo's preference
to kill it off. Either way this needs to happen for 2.6.21 since dynticks
has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactored and cleaned up ucc_fast.c and ucc_slow.c so that the two files
look more alike and are easier to read. Removed uccf_printk() and related
functions, because they were just front-ends to printk(). Fixed some
spacing and tabbing issues. Minor optimizations of some code. Changed
the type of some variables to their proper type (mostly buffer
descriptors).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add function of_get_mac_address(), which obtains the best MAC address to use
from the device tree by checking various properties in order. The order is:
'mac-address', then 'local-mac-address', then 'address'. It skips properties
that contain invalid MAC addresses, which were probably not initialized
by U-Boot.
Update gfar_of_init() and fs_enet_of_init() in fsl_soc.c to call
of_get_mac_address().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Getting BenH's new EMAC driver working on 440GP, I found some more
problems in the native mode paths of the new DCR code:
- dcr_map() is supposed to return a dcr_host_t, but the native
version is a macro that doesn't expand to an expression. With native
DCRs, dcr_host_t is an empty structure, so we just use a constructor
expression instead.
- dcr_unmap() uses {} instead of the safer do {} while (0)
idiom to implement a no-op
Here's a fix.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds driver code for the PMI device found in future IBM products.
PMI stands for "Platform Management Interrupt" and is a way to
communicate with the BMC (Baseboard Management Controller).
It provides bidirectional communication with a low latency.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 system manager support and the ppc_md routines restart() and
power_off().
The system manager provides an event notification mechanism for reporting
events like thermal alert and button presses. It also provides support to
control system shutdown and startup.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanups for the PS3 vuart driver.
- Hide driver private data from external interface with new structure
ps3_vuart_port_priv.
- Fix masking bug in ps3_vuart_get_interrupt_status().
- Add new helper routine ps3_vuart_clear_rx_bytes() to flush rx buffer.
- Add new variable probe_mutex to serialize probe and destroy routines.
- Rename some symbols.
- Add platform check in ps3_vuart_bus_init().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_early_init() is a function used on 64 bit systems, which
initializes whichever early udbg backend is configured. This function
is not called on 32-bit, however if btext early debug is enabled it
does have an explicit, inline, #ifdef-ed assignment performing
analagous initialization.
This patch makes things more uniform by folding the btext
initialization as an option into udbg_early_init() and calling that
from the 32-bit setup path.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a clean up patch that includes the following changes:
-Some comments were added to clarify the code based on feedback
from the community.
-The write_pm_cntrl() and set_count_mode() were passed a
structure element from a global variable. The argument was
removed so the functions now just operate on the global directly.
-The set_pm_event() function call in the cell_virtual_cntr()
routine was moved to a for-loop before the for_each_cpu loop
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It doesn't make any sense to have a priority field in the physical spu
structure. Move it into the spu context instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The recent vDSO consolidation patches broke powerpc due to a mistake
in the definition of MAXPAGES constants. This fixes it by moving to
a dynamically allocated array of pages instead as I don't like much
hard coded size limits. Also move the vdso initialisation to an initcall
since it doesn't really need to be done -that- early.
Applogies for not catching the breakage earlier, Roland _did_ CC me on
his patches a while ago, I got busy with other things and forgot to test
them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During ppc64+ppc merge virtual DMA code for floppy driver was not
ported. This patch restores virtual DMA support for floppy in new
powerpc target.
It is necessary at least on Pegasos and AmigaOne machines for the
floppy drive to function. ISA DMA controller works incorrectly there
due to its addressing limitations.
Virtual DMA mode is activated by floppy=nodma option passed to the
kernel (or module). There's no automatic switch like on i386.
Signed-off-by: Pavel Fedin <sonic_amiga@rambler.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3: Cleanup the frame buffer device before clearing the HPTE mapping
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ps3fb is available, we have to disable display flipping while changing the
audio or video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 Virtual Frame Buffer Driver.
As the actual graphics hardware cannot be accessed directly by Linux, ps3fb
uses a virtual frame buffer in main memory. The actual screen image is copied
to graphics memory by the GPU on every vertical blank, by making a hypervisor
call.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preallocate bootmem memory for the PS3 frame buffer device, which needs a
large block of physically-contiguous memory. The size of this memory block is
configurable:
- The config option CONFIG_FB_PS3_DEFAULT_SIZE_M allows to specify the
default amount of memory (in MiB) allocated to the virtual frame buffer.
- The early boot parameter `ps3fb=xxx' allows to override the default value.
It will be rounded up to a multiple of 1 MiB, if needed.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 AV Settings Driver.
The AV Settings driver is used to control Audio and Video settings. It
communicates with the policy manager through the virtual uart.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The line discipline numbers N_* are currently defined for each architecture
individually, but (except for a seeming mistake) identically, in
asm/termios.h. There is no obvious reason why these numbers should be
architecture specific, nor any apparent relationship with the termios
structure. The total number of these, NR_LDISCS, is defined in linux/tty.h
anyway. So I propose the following patch which moves the definitions of
the individual line disciplines to linux/tty.h too.
Three of these numbers (N_MASC, N_PROFIBUS_FDL, and N_SMSBLOCK) are unused
in the current kernel, but the patch still keeps the complete set in case
there are plans to use them yet.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the 'us_regs' field of the ucc_slow_info structure in ucc_slow.h
to just 'regs'. The equivalent field in the ucc_fast_info structure is
also called 'regs', so this patch makes them comparable, and makes the
code a little easier to read, because there already is a 'us_regs' in
another ucc_slow structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added kprobes to ppc32 platforms that have use single_step_exception. This
excludes 4xx and anything Book-E since their debug mechanisms for single stepping
are completely different.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call. This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new dcr code does not currently compile when configured for native
DCR access on ARCH=powerpc. This patch fixes the problems.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Early debug output for PA Semi UART. Uses the 2.05 CI real mode ops.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds base support for Celleb platform.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Spu management ops in arch/platforms/cell/spu_priv1_mmio.h can be used
commonly in of based platform. This patch separates spu management ops
from native cell code and uses on celleb platform.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds udbg support for Celleb platform.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This contains important fixes for the CPM2 PIC code. Eliminated
CPM_IRQ_OFFSET, pulling the respective interrupt numbers from the interrupt
mapping. Updated devicetree files to reflect that. Changed direct
IC-related IO accesses to the IO accessors. Fixed all the sense values to
keep coherency with ipic. In the current code, CPM2 stuff will have no IRQs
and hence could be hardly usable.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the structures and routines needed for PS3 vuart port device registration
to asm-powerpc/ps3.h.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the PS3 system bus routines from drivers/ps3 to
arch/powerpc/platforms/ps3.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow more than the default 256 MPIC sources. Allocates a new flag
(MPIC_LARGE_VECTORS) to be used by platform code when instantiating
the mpic.
I picked 11 bits worth right now since it would cover the number of
sources on any hardware I have seen. It can always be increased later
if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for PA6T-style PMC registers.
PMCs are completely implementation-dependent on PPC, and PA6T numbers them
differently from the IBM model.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add cputable entries for which type of PMC implementation the processor
has.
I've only filled in the current 64-bit processors, the unfilled default
value will have same behaviour as before so it can be done over time
as needed.
Also tidy up the dummy_perf implementation a bit, aggregating it into
one function with ifdefs instead of several.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the ctr_read/write a bit. It's currently defined in the
include but only used in one C file each. The only exception is the
classic version, so keep that in the include and define in the C file
as appropriate.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove an unneeded header include from ps3.h.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the PS3 AV settings driver to access the default video mode stored in
the OS area.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new routine ps3_get_firmware_version() and use it to output the firmware
version to dmesg.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 interrupt core update:
- Add ps3_alloc_irq() and ps3_free_irq(), to allocate a virtual interrupt
number for an interrupt outlet, which is needed by the PS3 GPU frame
buffer device and audio drivers
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 irq allocation routines to take an argument indicating which
cpu (processor thread) the interrupt should be serviced on.
The current system configuration favors device interrupts that are serviced
on cpu0, so that is used as the default.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Various fixes for the PS3 repository code:
- Sync signatures of function prototypes and implementations (enum vs.
unsigned int)
- Correct references to `regions' as `registers':
o Correct enum ps3_region_type as enum ps3_reg_type,
o Correct PS3_REGION_TYPE_* as PS3_REG_TYPE_*,
o Correct ps3_repository_find_region() as ps3_repository_find_reg().
- Correct function name in pr_debug() call
- Minor error condition improvements.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This add support of the Freescale mpc86xads reference board to
arch/powerpc. Supported SMC1 and SMC2 (UART and serial console), FEC
100Mbps Ethernet, SCC1 Ethernet (10Mbps hdx)
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This covers common CPM access functions, CPM interrupt controller code,
micropatch and a few compatibility things to kee the same driver base
working with arch/ppc. This version is refined with all the comments
(mostly PIC-related) addressed.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
do { } while(0) is not a good imitation of function returning void;
use ((void)0) instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's useful to have access to struct ipic handle that just got created
in ipic_init().
For example, if we want to setup an external IRQ with out
a device node we need access ipic->irqhost to create the virtual to HW
IRQ mapping and to set the IRQ sense. With this we can mimic the old
sense array concept that existed in arch/ppc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds irq remapping hook. On interrupt mechanism on Beat,
when an irq outlet which has an id which is formerly used is created,
remapping the irq is required.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Struct pci_controller doesn't prepare for the dependent data of each
specific bus. This patch adds private member to struct pci_controller.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I often test new versions of glibc by doing:
LD_LIBRARY_PATH=/XXX/lib /XXX/lib/ld.so.1 <binary>
One test case ended up SEGV'ing. Upon closer inspection ld.so was loaded
at 0x8000000 (128MB) with the heap right after it. Since we normally
link binaries at 0x10000000 (256MB) we only had about 128MB of space for
the heap:
00100000-00103000 r-xp 00100000 00:00 0 [vdso]
08000000-0801e000 r-xp 00000000 00:01 33079 /lib/ld-2.5.so
0802d000-0802f000 rwxp 0001d000 00:01 33079 /lib/ld-2.5.so
0802f000-08050000 rwxp 0802f000 00:00 0 [heap]
0fe91000-0ffd9000 r-xp 00000000 00:01 33082 /lib/libc-2.5.so
0ffd9000-0ffe8000 ---p 00148000 00:01 33082 /lib/libc-2.5.so
0ffe8000-0ffea000 r--p 00147000 00:01 33082 /lib/libc-2.5.so
0ffea000-0ffed000 rwxp 00149000 00:01 33082 /lib/libc-2.5.so
10000000-10004000 r-xp 00000000 00:01 76 /bin/sleep
10013000-10014000 rwxp 00003000 00:01 76 /bin/sleep
ffb41000-ffb56000 rw-p ffb41000 00:00 0 [stack]
One way to fix this is move ELF_ET_DYN_BASE from 0x08000000 to 0x20000000.
This allows 128MB for the binary (hopefully enough for even the most
crazy c++ apps), and with our current layout we will grow the heap up
and the stack down, allowing potentially gigabytes of heap:
00100000-00103000 r-xp 00100000 00:00 0 [vdso]
0fe8a000-0ffd3000 r-xp 00000000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffd3000-0ffe3000 ---p 00149000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffe3000-0ffea000 r--p 00149000 00:01 3350 /lib/tls/libc-2.3.6.so
0ffea000-0ffee000 rwxp 00150000 00:01 3350 /lib/tls/libc-2.3.6.so
10000000-10004000 r-xp 00000000 00:01 76 /bin/sleep
10013000-10014000 rwxp 00003000 00:01 76 /bin/sleep
20000000-20018000 r-xp 00000000 00:01 3478 /lib/ld-2.3.6.so
20028000-20029000 r--p 00018000 00:01 3478 /lib/ld-2.3.6.so
20029000-2002a000 rwxp 00019000 00:01 3478 /lib/ld-2.3.6.so
2002a000-2004b000 rwxp 2002a000 00:00 0 [heap]
ffd67000-ffd7c000 rw-p ffd67000 00:00 0 [stack]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 64-bit machines, if an atomic counter is explicitly set to a
negative value, the atomic_dec_if_positive function will decrement and
store the next smallest value in the atomic counter, contrary to its
intended operation.
The comparison to determine if the decrement will make the result
negative was done by the "addic." instruction, which operates on a
64-bit value, namely the zero-extended word loaded from the atomic
variable. This patch uses an explicit word compare (cmpwi) and
changes the addic. to an addi (also changing "=&r" to "=&b" so that r0
isn't used, and addi doesn't become li).
This also fixes a bug for both 32-bit and 64-bit in that previously
0x80000000 was considered positive, since the result after
decrementing is positive. Now it is considered negative.
Also, I clarify the return value in the comments just to make it clear
that the value returned is always the decremented value, even if that
value is not stored back to the atomic counter.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
unionfs managed to hit this on s390. Some architectures use __ptr_t in their
FD_ZERO implementation. We don't have a __ptr_t. Switch them over to plain
old void*.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were a few issues with the HCALL_STATS code:
- PURR cpu feature checks were backwards
- We iterated one entry off the end of the hcall_stats array
- Remove dead update_hcall_stats() function prototype
I noticed one thing while debugging, and that is we call H_ENTER (to set
up the MMU hashtable in early init) before we have done the cpu fixups.
This means we will execute the PURR SPR reads even on a CPU that isnt
capable of it. I wonder if we can move the CPU feature fixups earlier.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using device_initcall makes it happen for every platform that
compiles this file in. This is really bad, for obvious reasons.
Instead, we use the .init field of the machine description. If
the platform needs the hook to do something specific it can provides
its own function and call mpc52xx_declare_of_platform_devices from
there. If not, the mpc52xx_declare_of_platform_devices function can
directly be used as the init hook.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we switched over to the generic BUG mechanism we forgot to change
the assembly code which open-codes a WARN_ON() in enter_rtas(), so the
bug table got corrupted.
This patch provides an EMIT_BUG_ENTRY macro for use in assembly code,
and uses it in entry_64.S. Tested with CONFIG_DEBUG_BUGVERBOSE on ppc64
but not without -- I tried to turn it off but it wouldn't go away; I
suspect Aunt Tillie probably needed it.
This version gets __FILE__ and __LINE__ right in the assembly version --
rather than saying include/asm-powerpc/bug.h line 21 every time which is
a little suboptimal.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Virtually index, physically tagged cache architectures can get away
without cache flushing when forking. This patch adds a new cache
flushing function flush_cache_dup_mm(struct mm_struct *) which for the
moment I've implemented to do the same thing on all architectures
except on MIPS where it's a no-op.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, to tell a task that it should go to the refrigerator, we set the
PF_FREEZE flag for it and send a fake signal to it. Unfortunately there
are two SMP-related problems with this approach. First, a task running on
another CPU may be updating its flags while the freezer attempts to set
PF_FREEZE for it and this may leave the task's flags in an inconsistent
state. Second, there is a potential race between freeze_process() and
refrigerator() in which freeze_process() running on one CPU is reading a
task's PF_FREEZE flag while refrigerator() running on another CPU has just
set PF_FROZEN for the same task and attempts to reset PF_FREEZE for it. If
the refrigerator wins the race, freeze_process() will state that PF_FREEZE
hasn't been set for the task and will set it unnecessarily, so the task
will go to the refrigerator once again after it's been thawed.
To solve first of these problems we need to stop using PF_FREEZE to tell
tasks that they should go to the refrigerator. Instead, we can introduce a
special TIF_*** flag and use it for this purpose, since it is allowed to
change the other tasks' TIF_*** flags and there are special calls for it.
To avoid the freeze_process()-refrigerator() race we can make
freeze_process() to always check the task's PF_FROZEN flag after it's read
its "freeze" flag. We should also make sure that refrigerator() will
always reset the task's "freeze" flag after it's set PF_FROZEN for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
Make powerpc's __ilog2_u64() take a 64-bit argument.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes powerpc use the generic BUG machinery. The biggest reports the
function name, since it is redundant with kallsyms, and not needed in general.
There is an overall reduction of code, since module_32/64 duplicated several
functions.
Unfortunately there's no way to tell gcc that BUG won't return, so the BUG
macro includes a goto loop. This will generate a real jmp instruction, which
is never used.
[akpm@osdl.org: build fix]
[paulus@samba.org: remove infinite loop in BUG_ON]
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Hugh Dickens <hugh@veritas.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 85xx we don't build in dcr support because the core doesn't implement the
instructions. This caused problems when building an 85xx kernel. Additionally
made it so we only build __mtdcr/__mfdcr if we are CONFIG_PPC_DCR_NATIVE.
The 85xx build issue wasPointed out by Dai Haruki.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Large sched domains can be very expensive to scan. Add an option SD_SERIALIZE
to the sched domain flags. If that flag is set then we make sure that no
other such domain is being balanced.
[akpm@osdl.org: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Peter Williams <pwil3058@bigpond.net.au>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now we have a SPURR cpu feature bit, we can export it to userspace in
sysfs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
POWER6 adds a new SPR, the data stream control register (DSCR). It can
be used to adjust how agressive the prefetch mechanisms are.
Its possible we may want to context switch this, but for now just export
it to userspace via sysfs so we can adjust it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to sort out our struct termios and add proper speed control we need
to separate the kernel and user termios structures. Glibc is fine but the
other libraries rely on the kernel exported struct termios and we need to
extend this without breaking the ABI/API
To do so we add a struct ktermios which is the kernel view of a termios
structure and overlaps the struct termios with extra fields on the end for
now. (That limitation will go away in later patches). Some platforms (eg
alpha) planned ahead and thus use the same struct for both, others did not.
This just adds the structures but does not use them, it seems a sensible
splitting point for bisect if there are compile failures (not that I expect
them)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide ilog2() fallbacks for powerpc for 32-bit numbers and 64-bit numbers on
ppc64.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The e300c2 has no FPU. Its MSR[FP] is grounded to zero. If an attempt
is made to execute a floating point instruction (including floating-point
load, store, or move instructions), the e300c2 takes a floating-point
unavailable interrupt.
This patch adds support for FP emulation on the e300c2 by declaring a
new CPU_FTR_FP_TAKES_FPUNAVAIL, where FP unavail interrupts are
intercepted and redirected to the ProgramCheck exception path for
correct emulation handling.
(If we run out of CPU_FTR bits we could look to reclaim this bit by adding
support to test the cpu_user_features for PPC_FEATURE_HAS_FPU instead)
It adds a nop to the exception path for 32-bit processors with a FPU.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The powerpc version of pci_resource_to_user() and associated hooks
used by /proc/bus/pci and /sys/bus/pci mmap have been broken for some
time on machines that don't have a 1:1 mapping of devices (basically
on non-PowerMacs) and have PCI devices above 32 bits.
This attempts to fix it as well as possible.
The rule is supposed to be that pci_resource_to_user() always converts
the resources back into a BAR values since that's what the /proc
interface was supposed to deal with. However, for X to work on
platforms where PCI MMIO is not mapped 1:1, it became a habit of
platforms like powerpc to pass "fixed up" values there since X expects
to be able to use values from /proc/bus/pci/devices as offsets to mmap
of /dev/mem...
So we keep that contraption here, causing also /sys/*/resource to
expose fully absolute MMIO addresses instead of BAR values, which is
ugly, but should still work as long as those are only used to calculate
alignment within a page.
X is still broken when built 32 bits on machines where PCI MMIO can be
above 32-bit space unfortunately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To test for the existence of an RTAS function, we typically do:
foo_token = rtas_token("foo");
if (foo_token == RTAS_UNKNOWN_SERVICE)
return;
Add a rtas_service_present method, which provides a more conventional
boolean interface for testing the existence of an RTAS method.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ack_irq macro is unused and conflicts with James' work to template
the generic irq code. mask_irq and unmask_irq are also unused, so delete
those macros too.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current PowerPC code makes pci_unmap_addr(), pci_unmap_addr_set(),
and friends trivial for all 32-bit kernels. This is reasonable, since
for those kernels it is true that pci_unmap_single() does not need the
DMA address from the original DMA mapping -- in fact, it is a NOP.
However, I recently tried the tg3 driver on a PowerPC 440SPe machine,
which runs a 32-bit kernel and has non-cache-coherent PCI DMA. I
found that the tg3 driver crashed in pci_dma_sync_single_for_cpu(),
since for non-coherent systems, that function must invalidate the
cache for the DMA address range requested, and therefore it does use
the address passed in. tg3 uses a DMA address it stashes away with
pci_unmap_addr_set() and retrieves with pci_unmap_addr(). Of course,
since pci_unmap_addr() is defined to (0) right now, this doesn't work.
It seems to me that the tg3 driver is using pci_unmap_addr() in a
legitimate way -- I wouldn't want to have to teach all drivers that
they should use pci_unmap_addr() if they only need the address for
unmapping functions, but if they want the pci_dma_sync functions, then
they have to store the DMA address without the helper macros.
The right fix therefore seems to be in the definition of the macros in
<asm/pci.h> -- we should use the trivial versions only for 32-bit
kernels for coherent systems, and the real versions for both 64-bit
kernels and non-coherent systems.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It uses #ifdef __KERNEL__, so needs to be processed with unifdef.
Signed-off-by: Arnd Bergann <arnd.bergmann@de.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c,
this allows rtas_stop_self() to be static so remove the prototype.
Wire up pSeries_mach_cpu_die() in the initcall, rather than statically
in setup.c, the initcall will still run prior to the cpu hotplug code
being callable, so there should be no change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the contents of the userspace asm/setup.h header consistent on all
architectures:
- export setup.h to userspace on all architectures
- export only COMMAND_LINE_SIZE to userspace
- frv: move COMMAND_LINE_SIZE from param.h
- i386: remove duplicate COMMAND_LINE_SIZE from param.h
- arm:
- export ATAGs to userspace
- change u8/u16/u32 to __u8/__u16/__u32
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass struct dev pointer to dma_cache_sync()
dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard. Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dma_is_consistent() is ill-designed in that it does not have a struct
device pointer argument which makes proper support for systems that consist
of a mix of coherent and non-coherent DMA devices hard. Change
dma_is_consistent to take a struct device pointer as first argument and fix
the sole caller to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define elf_addr_t in linux/elf.h. The size of the type is determined using
ELF_CLASS. This allows us to remove the defines that today are spread all
over .c and .h files.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Daniel Jacobowitz <drow@false.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last thing we agreed on was to remove the macros entirely for 2.6.19,
on all architectures. Unfortunately, I think nobody actually _did_ that,
so they are still there.
[akpm@osdl.org: x86_64 fix]
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Schafer <gschafer@zip.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce pagefault_{disable,enable}() and use these where previously we did
manual preempt increments/decrements to make the pagefault handler do the
atomic thing.
Currently they still rely on the increased preempt count, but do not rely on
the disabled preemption, this might go away in the future.
(NOTE: the extra barrier() in pagefault_disable might fix some holes on
machines which have too many registers for their own good)
[heiko.carstens@de.ibm.com: s390 fix]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.
Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.
The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds utility routines used by 52xx device drivers and board support
code. Main functionality is to add device nodes to the of_platform_bus,
retrieve the IPB bus frequency, and find+ioremap device registers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no need to expose these settings outside the scope
of the interrupt controller code itself.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow arch/powerpc/kernel/crash.c to build on 32-bit we need a
definition of hard_irq_disable(). 32-bit doesn't support the lazy
interrupt disabling mechanism, so on 32-bit hard_irq_disable() is
simply local_irq_disable(). Add a definition for hard_irq_enable()
just for completeness.
This allows (KEXEC=y && PPC32=y) to build again. Broken since
d04c56f73c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.
If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At least the ide driver calls pcibus_to_node, which is not
defined when CONFIG_PCI is disabled. This adds a nop function
for the !PCI case.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.
Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.
The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.
I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It may be desireable to build a kernel for cell without
spufs, e.g. as the initial kboot kernel. This requires
that the SPU specific parts of the core dump and the xmon
code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds a PS3 system bus driver. This system bus is a virtual bus used to present
the PS3 system devices in the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds some needed bits for a config option PS3_USE_LPAR_ADDR that disables
the PS3 lpar address translation mechanism. This is a currently needed
workaround for limitations in the design of the generic cell spu support.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds the core platform support for the PS3 game console and other devices
using the PS3 hypervisor.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This adds a platform specific spu management abstraction and the coresponding
routines to support the IBM Cell Blade. It also removes the hypervisor only
resources that were included in struct spu.
Three new platform specific routines are introduced, spu_enumerate_spus(),
spu_create_spu() and spu_destroy_spu(). The underlying design uses a new
type, struct spu_management_ops, to hold function pointers that the platform
setup code is expected to initialize to instances appropriate to that platform.
For the IBM Cell Blade support, I put the hypervisor only resources that were
in struct spu into a platform specific data structure struct spu_pdata.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This adds an accessor routine virq_to_hw() to the
virq routines which hides the implementation details
of the virq to hwirq map.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It saves #ifdef'ing in callers if we at least define the 64-bit cpu
features for 32-bit also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds SPU elf notes to the coredump. It creates a separate note
for each of /regs, /fpcr, /lslr, /decr, /decr_status, /mem, /signal1,
/signal1_type, /signal2, /signal2_type, /event_mask, /event_status,
/mbox_info, /ibox_info, /wbox_info, /dma_info, /proxydma_info, /object-id.
A new macro, ARCH_HAVE_EXTRA_NOTES, was created for architectures to
specify they have extra elf core notes.
A new macro, ELF_CORE_EXTRA_NOTES_SIZE, was created so the size of the
additional notes could be calculated and added to the notes phdr entry.
A new macro, ELF_CORE_WRITE_EXTRA_NOTES, was created so the new notes
would be written after the existing notes.
The SPU coredump code resides in spufs. Stub functions are provided in the
kernel which are hooked into the spufs code which does the actual work via
register_arch_coredump_calls().
A new set of __spufs_<file>_read/get() functions was provided to allow the
coredump code to read from the spufs files without having to lock the
SPU context for each file read from.
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This adds code to look at the properties firmware puts in the device
tree to determine what compatibility mode the partition is in on
POWER6 machines, and set the ELF aux vector AT_HWCAP and AT_PLATFORM
entries appropriately.
Specifically, we look at the cpu-version property in the cpu node(s).
If that contains a "logical" PVR value (of the form 0x0f00000x), we
call identify_cpu again with this PVR value. A value of 0x0f000001
indicates the partition is in POWER5+ compatibility mode, and a value
of 0x0f000002 indicates "POWER6 architected" mode, with various
extensions disabled. We also look for various other properties:
ibm,dfp, ibm,purr and ibm,spurr.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following routines are added to arch/powerpc/platforms/cell/pmu.c:
cbe_clear_pm_interrupts()
cbe_enable_pm_interrupts()
cbe_disable_pm_interrupts()
cbe_query_pm_interrupts()
cbe_pm_irq()
cbe_init_pm_irq()
This also adds a routine in arch/powerpc/platforms/cell/interrupt.c and
some macros in cbe_regs.h to manipulate the IIC_IR register:
iic_set_interrupt_routing()
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some PMU-related macros and function prototypes from cbe_regs.h
and pmu.h in arch/powerpc/platforms/cell/ to a new header at
include/asm-powerpc/cell-pmu.h
This is cleaner to use from the oprofile code, since that sits in
arch/powerpc/oprofile, not in the cell platform directory.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The /lslr file gives read access to the SPU_LSLR register in hex; 0x3fff
for example The /dma_info file provides read access to the SPU Command
Queue in a binary format. The /proxydma_info files provides read access
access to the Proxy Command Queue in a binary format. The spu_info.h
file provides data structures for interpreting the binary format of
/dma_info and /proxydma_info.
Signed-off-by: Dwayne Grant McConnell <decimal@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the definition of powerpc's cond_syscall() to use the standard gcc
weak attribute specifier which provides proper support for C linkage as
needed by spu_syscall_table[].
Fixes this powerpc build error with CONFIG_SPU_FS=y, CONFIG_PPC_RTAS=n:
arch/powerpc/platforms/built-in.o: undefined reference to `ppc_rtas'
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a small driver for the Xserve G5 CPU-meter blue LEDs on the
front-panel. It might work on the Xserve G4 as well though that was
not tested. It's pretty basic and could use some improvements if
somebody cares doing them. :)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new IO accessor code allows to stick a token in the top bit of MMIO
addresses which gets masked out during actual accesses. However, the
__raw_* accessors forgot to mask it out. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.
Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* sanitize prototypes, annotate
* kill useless shifts
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add arch specific dev_archdata to struct device
Adds an arch specific struct dev_arch to struct device. This enables
architecture to add specific fields to every device in the system, like
DMA operation pointers, NUMA node ID, firmware specific data, etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pSeries is the only architecture left using HAVE_ARCH_PCI_MWI and it's
really inappropriate for its needs. It really wants to disable MWI
altogether. So here are a pair of stub implementations for pci_set_mwi
and pci_clear_mwi.
Also rename pci_generic_prep_mwi to pci_set_cacheline_size since that
better reflects what it does.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the infrastructure is already in place for this, so we only need
to allocate a syscall number and hook it up.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the /sys/devices/system/cpu/*/topology/thread_siblings
files on powerpc. These files are already available on other
architectures.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When CONFIG_PCI option is not set, the variables
pci_dram_offset, isa_io_base and isa_mem_base are not defined.
Currently, the test is handled in each platform header. This
patch moves the test in io.h once and for all.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The qe_brg structure manually defined each of the 16 BRG registers, which
made any code that used them cumbersome. This patch replaces the fields
with a single 16-element array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this is to allow for error checking (check the return for NO_IRQ)
Added a check that the resource is non-NULL, too.
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Cleaned up interrupt mapping a little by adding a helper
function which parses the irq out of the device-tree, and puts
it into a resource.
* Changed the arch/ppc platform files to specify PHY_POLL, instead of -1
* Changed the fixed phy to use PHY_IGNORE_INTERRUPT
* Added ethtool.h and mii.h to phy.h includes
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for the MPC52xx Interrupt controller for
ARCH=powerpc.
It includes the main code in arch/powerpc/sysdev/ as well as a header
file in include/asm-powerpc.
Signed-off-by: Nicolas DET <nd@bplan-gmbh.de>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The _machine macro was once used for compatibility with ARCH=ppc
drivers. It is unused in current kernels, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current kernels always have one of CONFIG_PPC_MULTIPLATFORM or
CONFIG_PPC32 defined, so remove bogus ifdef.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
iommu_setup_pSeries() and iommu_setup_dart() are declared extern but
are not implemented, so remove them. Remove ifdef around extern
function declaration.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If mmiowb() is always used prior to releasing spinlock as Doc suggests,
then it's safe against preemption; but I'm not convinced that's always
the case. If preemption occurs between sync and get_paca()->io_sync = 0,
I believe there's no problem. But in the unlikely event that gcc does
the store relative to another register than r13 (as it did with current),
then there's a small danger of setting another cpu's io_sync to 0, after
it had just set it to 1. Rewrite ppc64 mmiowb to prevent that.
The remaining io_sync assignments in io.h all get_paca()->io_sync = 1,
which is harmless even if preempted to the wrong cpu (the context switch
itself syncs); and those in spinlock.h are while preemption is disabled.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repeated -j20 kernel builds on a G5 Quad running an SMP PREEMPT kernel
would often collapse within a day, some exec failing with "Bad address".
In each case examined, load_elf_binary was doing a kernel_read, but
generic_file_aio_read's access_ok saw current->thread.fs.seg as USER_DS
instead of KERNEL_DS.
objdump of filemap.o shows gcc 4.1.0 emitting "mr r5,r13 ... ld r9,416(r5)"
here for get_paca()->__current, instead of the expected and much more usual
"ld r9,416(r13)"; I've seen other gcc4s do the same, but perhaps not gcc3s.
So, if the task is preempted and rescheduled on a different cpu in between
the mr and the ld, r5 will be looking at a different paca_struct from the
one it's now on, pick up the wrong __current, and perhaps the wrong seg.
Presumably much worse could happen elsewhere, though that split is rare.
Other architectures appear to be safe (x86_64's read_pda is more limiting
than get_paca), but ppc64 needs to force "current" into one instruction.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 10Gigabit ethernet device drivers appear to be able to chew
up all 256MB of TCE mappings on pSeries systems, as evidenced by
numerous error messages:
iommu_alloc failed, tbl c0000000010d5c48 vaddr c0000000d875eff0 npages 1
Some experimentation indicates that this is essentially because
one 1500 byte ethernet MTU gets mapped as a 64K DMA region when
the large 64K pages are enabled. Thus, it doesn't take much to
exhaust all of the available DMA mappings for a high-speed card.
This patch changes the iommu allocator to work with its own
unique, distinct page size. Although the patch is long, its
actually quite simple: it just #defines a distinct IOMMU_PAGE_SIZE
and then uses this in all the places that matter.
As a side effect, it also dramatically improves network performance
on platforms with H-calls on iommu translation inserts/removes (since
we no longer call it 16 times for a 1500 bytes packet when the iommu HW
is still 4k).
In the future, we might want to make the IOMMU_PAGE_SIZE a variable
in the iommu_table instance, thus allowing support for different HW
page sizes in the iommu itself.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.
* Reorganized FSL Book-E performance monitoring code so that the 7450
wouldn't be built if the e500 was, and cleaned it up so it was more
self-contained.
* Added a cpu_setup function for FSL Book-E. The original
cpu_setup function prototype had no arguments, assuming that
the reg_setup function would copy the required information into
variables which represented the registers. This was silly for
e500, since it has 1 register per counter (rather than 3 for
all counters), so the code has been restructured to have
cpu_setup take the current counter config array as an argument,
with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
on_each_cpu(), and op_powerpc_cpu_setup() invoking the
model-specific cpu_setup function with an argument. The
argument is ignored on all other platforms at present.
* Fixed a confusing line where a trinary operator only had two
arguments
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The e500 core generates an illegal instruction exception when it tries
to execute the lwsync instruction, which we currently use for rmb().
This fixes it by using the LWSYNC macro, which turns into a plain sync
on 32-bit machines.
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for stopping, and restarting, spus
from xmon. We use the spu master runcntl bit to stop execution,
this is apparently the "right" way to control spu execution and
spufs will be changed in the future to use this bit.
Testing has shown that to restart execution we have to turn the
master runcntl bit on and also rewrite the spu runcntl bit, even
if it is already set to 1 (running).
Stopping spus is triggered by the xmon command 'ss' - "spus stop"
perhaps. Restarting them is triggered via 'sr'. Restart doesn't
start execution on spus unless they were running prior to being
stopped by xmon.
Walking the spu->full_list in xmon after a panic, would mean
corruption of any spu struct would make all the others
inaccessible. To avoid this, and also to make the next patch
easier, we cache pointers to all spus during boot.
We attempt to catch and recover from errors while stopping and
restarting the spus, but as with most xmon functionality there are
no guarantees that performing these operations won't crash xmon
itself.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to add sysfs attributes to all spu's, there is a
need for a list of all available spu's. Adding the device_node
makes also sense, as it is needed for proper register access.
This patch also adds two functions to create and remove sysfs
attributes and attribute_groups to all spus.
That allows to group spu attributes in a subdirectory like:
/sys/devices/system/spu/spuX/group_name/what_ever
This will be used by cbe_thermal to group all attributes dealing with
thermal support in one directory.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds two new flags to spu_create:
SPU_CREATE_NONSCHED: create a context that is never moved
away from an SPE once it has started running. This flag
can only be used by tasks with the CAP_SYS_NICE capability.
SPU_CREATE_ISOLATED: create a nonschedulable context that
enters isolation mode upon first run. This requires the
SPU_CREATE_NONSCHED flag.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the mostly unused variable isrc from struct spu and a forgotten
function declaration.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SPRN_SDR1 and the SPE's MFC SDR are hypervisor resources and
are not accessible from a logical partition. This change adds an
access wrapper.
When running on bare H/W, the spufs needs to only set the SPE's MFC SDR
to the value of the PPE's SPRN_SDR1 once at SPE initialization, so this
change renames mfc_sdr_set() to mfc_sdr_setup() and moves the
access of SPRN_SDR1 into the mmio wrapper. It also removes the now
unneeded member mfc_sdr_RW from struct spu_priv1_collapsed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
On CHRP platforms with only a 8259 controller, we should set the
default IRQ host to the 8259 driver's one for the IRQ probing
fallbacks to work in case the IRQ tree is incorrect (like on
Pegasos for example). Without this fix, we get a bunch of WARN_ON's
during boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a const'ification related warning with device_is_compatible()
and friends related to get_property() not properly having const
on it's input device node argument.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell CPU timebase has an erratum. When reading the entire 64 bits
of the timebase with one mftb instruction, there is a handful of cycles
window during which one might read a value with the low order 32 bits
already reset to 0x00000000 but the high order bits not yet incremeted
by one. This fixes it by reading the timebase again until the low order
32 bits is no longer 0. That might introduce occasional latencies if
hitting mftb just at the wrong time, but no more than 70ns on a cell
blade, and that was considered acceptable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:
.long label (or .llong on 64 bits)
will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.
The idea here (thanks Alan Modra !) is to instead use something like:
1:
.long label - 1b
That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.
Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:
.llong label - 1b (Or even just .llong label)
That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:
.long 0xffffffff
.llong label - 1b
Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds some macros that can be used with an explicit label in
order to nest cpu features. This should be used very careful but is
necessary for the upcoming cell TB fixup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.
This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the powerpc hpte_insert routines now called through ppc_md to
static scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently we've copied the todc drivers, for various RTCs used in
embedded machines from ARCH=ppc to ARCH=powerpc, despite the fact that
it's never used in the latter. This patch removes it.
If we ever need these drivers (which we probably shouldn't now the RTC
class stuff is in), we can transfer them one by one from ARCH=ppc,
removing from the hideous abomination which is the todc
"infrastructure".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a lazy strategy for disabling interrupts. This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca. If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns. This means that interrupts only
actually get disabled in the processor when an interrupt comes along.
When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled. If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.
This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.
This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw. This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags. This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's nothing arch-specific about check_signature(), so move it to
<linux/io.h>. Use a cross between the Alpha and i386 implementations as
the generic one.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
David Woodhouse points out that the comment accompanying the MTFSF_L
macro is misleading. We should make it clear that the L bit is ignored
on older CPUS, not the entire instruction.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This adds an 'object-id' file that the spe library can
use to store a pointer to its ELF object. This was
originally meant for use by oprofile, but is now
also used by the GNU debugger, if available.
In order for oprofile to find the location in an spu-elf
binary where an event counter triggered, we need a way
to identify the binary in the first place.
Unfortunately, that binary itself can be embedded in a
powerpc ELF binary. Since we can assume it is mapped into
the effective address space of the running process,
have that one write the pointer value into a new spufs
file.
When a context switch occurs, pass the user value to
the profiler so that can look at the mapped file (with
some care).
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the concept of a gang to spufs as a new type of object.
So far, this has no impact whatsover on scheduling, but makes
it possible to add that later.
A new type of object in spufs is now a spu_gang. It is created
with the spu_create system call with the flags argument set
to SPU_CREATE_GANG (0x2). Inside of a spu_gang, it
is then possible to create spu_context objects, which until
now was only possible at the root of spufs.
There is a new member in struct spu_context pointing to
the spu_gang it belongs to, if any. The spu_gang maintains
a list of spu_context structures that are its children.
This information can then be used in the scheduler in the
future.
There is still a bug that needs to be resolved in this
basic infrastructure regarding the order in which objects
are removed. When the spu_gang file descriptor is closed
before the spu_context descriptors, we leak the dentry
and inode for the gang. Any ideas how to cleanly solve
this are appreciated.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This tries to fix spufs so we have an interface closer to what is
specified in the man page for events returned in the third argument of
spu_run.
Fortunately, libspe has never been using the returned contents of that
register, as they were the same as the return code of spu_run (duh!).
Unlike the specification that we never implemented correctly, we now
require a SPU_CREATE_EVENTS_ENABLED flag passed to spu_create, in
order to get the new behavior. When this flag is not passed, spu_run
will simply ignore the third argument now.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds NUMA support to the the spufs scheduler.
The new arch/powerpc/platforms/cell/spufs/sched.c is greatly
simplified, in an attempt to reduce complexity while adding
support for NUMA scheduler domains. SPUs are allocated starting
from the calling thread's node, moving to others as supported by
current->cpus_allowed. Preemption is gone as it was buggy, but
should be re-enabled in another patch when stable.
The new arch/powerpc/platforms/cell/spu_base.c maintains idle
lists on a per-node basis, and allows caller to specify which
node(s) an SPU should be allocated from, while passing -1 tells
spu_alloc() that any node is allowed.
Since the patch removes the currently implemented preemptive
scheduling, it is technically a regression, but practically
all users have since migrated to this version, as it is
part of the IBM SDK and the yellowdog distribution, so there
is not much point holding it back while the new preemptive
scheduling patch gets delayed further.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (25 commits)
[POWERPC] Add support for the mpc832x mds board
[POWERPC] Add initial support for the e300c2 core
[POWERPC] Add MPC8360EMDS default dts file
[POWERPC] Add MPC8360EMDS board support
[POWERPC] Add QUICC Engine (QE) infrastructure
[POWERPC] Add QE device tree node definition
[POWERPC] Don't try to just continue if xmon has no input device
[POWERPC] Fix a printk in pseries_mpic_init_IRQ
[POWERPC] Get default baud rate in udbg_scc
[POWERPC] Fix zImage.coff on oldworld PowerMac
[POWERPC] Fix xmon=off and cleanup xmon initialisation
[POWERPC] Cleanup include/asm-powerpc/xmon.h
[POWERPC] Update swim3 printk after blkdev.h change
[POWERPC] Cell interrupt rework
POWERPC: mpc82xx merge: board-specific/platform stuff(resend)
POWERPC: 8272ads merge to powerpc: common stuff
POWERPC: Added devicetree for mpc8272ads board
[POWERPC] iSeries has no legacy I/O
[POWERPC] implement BEGIN/END_FW_FTR_SECTION
[POWERPC] iSeries does not need pcibios_fixup_resources
...
Add QUICC Engine (QE) configuration, header files, and
QE management and library code that are used by QE devices
drivers.
Includes Leo's modifications up to, and including, the
platform_device to of_device adaptation:
"The series of patches add generic QE infrastructure called
qe_lib, and MPC8360EMDS board support. Qe_lib is used by
QE device drivers such as ucc_geth driver.
This version updates QE interrupt controller to use new irq
mapping mechanism, addresses all the comments received with
last submission and includes some style fixes.
v2: Change to use device tree for BCSR and MURAM;
Remove I/O port interrupt handling code as it is not generic
enough.
v3: Address comments from Kumar; Update definition of several
device tree nodes; Copyright style change."
In addition, the following changes have been made:
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o fixed qe_snums_init() serial num assignment to use a const array
o made CONFIG_UCC_FAST select UCC_SLOW
o reduced NR_QE_IC_INTS from 128 to 64
o remove _IO_BASE, etc. defines (not used)
o removed irrelevant comments, added others to resemble removed BD_ defines
o realigned struct definitions in headers
o various other style fixes including things like pinMask -> pin_mask
o fixed a ton of whitespace issues
o marked ioregs as __be32/__be16
o removed platform_device code and redundant get_qe_base()
o removed redundant comments
o added cpu_relax() to qe_reset
o uncasted all get_property() assignments
o eliminated unneeded casts
o eliminated immrbar_phys_to_virt (not used)
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch to make the early xmon logic work with earlier early param
parsing (480f6f35a1) breaks xmon=off.
No one does this obviously as xmon rocks, but it should really work
as documented.
While fixing that it struck me that we could move the xmon param
handling into xmon.c, and also consolidate the
xmon_init()/do_early_xmon logic into xmon_setup(). This means
xmon=early drops into xmon a little earlier on 32-bit, but it
seems to work just fine.
Tested on PSERIES and CLASSIC32.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For some reason we have two prototypes for xmon_init(), remove the
one in system.h.
No one calls xmon() anymore, debugger() is preferable, so we don't
need the prototype. And similarly no one calls xmon_printf().
Also update the include guards on xmon.h to match the standard
format, add copyright and license, and add comments to #endifs.
Built for pseries_defconfig and pmac32_defconfig.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
Introduce the child field in sched_domain struct and use it in
sched_balance_self().
We will also use this field in cleaning up the sched group cpu_power
setup(done in a different patch) code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last change for partport_pc did fix the common case for all PowerMacs,
but it broke the case for PCI multiport IO cards. In fact, the config
option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed
the parport driver. It enables the winbond and smsc probing.
Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will
take care of it. All powerpc configs should have
CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp
boards we tested it on.
Tested on a G4/466 with a PCI card:
0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
Subsystem: Timedia Technology Co Ltd Unknown device 5079
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 53
Region 0: I/O ports at f2000800 [size=32]
Region 2: I/O ports at f2000870 [size=8]
Region 3: I/O ports at f2000860 [size=8]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures provide an execve function that does not set errno, but
instead returns the result code directly. Rename these to kernel_execve to
get the right semantics there. Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.
[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the regs_return_value() macro to extract the return value in an
architecture agnostic manner, given the pt_regs.
Other architecture maintainers may want to add similar helpers.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kallsyms_lookup_name() allows for <module:symbol> style specification for
looking up symbol addresses. Handle the case where the user specifies
<module:.symbol> on powerpc, given that 64-bit powerpc uses function
descriptors.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In an effort to make kprobe modules more portable, here is a patch that:
o Introduces the "symbol_name" field to struct kprobe.
The symbol->address resolution now happens in the kernel in an
architecture agnostic manner. 64-bit powerpc users no longer have
to specify the ".symbols"
o Introduces the "offset" field to struct kprobe to allow a user to
specify an offset into a symbol.
o The legacy mechanism of specifying the kprobe.addr is still supported.
However, if both the kprobe.addr and kprobe.symbol_name are specified,
probe registration fails with an -EINVAL.
o The symbol resolution code uses kallsyms_lookup_name(). So
CONFIG_KPROBES now depends on CONFIG_KALLSYMS
o Apparantly kprobe modules were the only legitimate out-of-tree user of
the kallsyms_lookup_name() EXPORT. Now that the symbol resolution
happens in-kernel, remove the EXPORT as suggested by Christoph Hellwig
o Modify tcp_probe.c that uses the kprobe interface so as to make it
work on multiple platforms (in its earlier form, the code wouldn't
work, say, on powerpc)
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add powerpc get/set_rtc_time interface to new generic rtc class. This
abstracts rtc chip specific code from the platform code for rtc-over-i2c
platforms. Specific RTC chip support is now configured under
Device Drivers -> Real Time Clock. Setting time of day from the RTC
on startup is also configurable.
this time without the potentially platform breaking initcall.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc can boot one single binary on prep, chrp and pmac boards. ppc64 can
boot one single binary on pseries and G5 boards. pmac has no legacy io,
probing for PC style legacy hardware (or accessing the legacy io area
regulary) may lead to a hard crash:
* add check for parport_pc, exit on pmac. 32bit chrp has no
->check_legacy_ioport, the probe is always called. 64bit chrp has
check_legacy_ioport, check for a "parallel" node
* add check for isapnp, only PReP boards may have real ISA slots. 32bit
PReP will have no ->check_legacy_ioport, the probe is always called.
* update code in i8042_platform_init. Run ->check_legacy_ioport first,
always call request_region. No functional change. Remove whitespace
before i8042_reset init.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Powerpc already has a directed yield for CONFIG_PREEMPT="n". To make it
work with CONFIG_PREEMPT="y" as well the _raw_{spin,read,write}_relax
primitives need to be defined to call __spin_yield() for spinlocks and
__rw_yield() for rw-locks.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems running with virtual cpus there is optimization potential in
regard to spinlocks and rw-locks. If the virtual cpu that has taken a lock
is known to a cpu that wants to acquire the same lock it is beneficial to
yield the timeslice of the virtual cpu in favour of the cpu that has the
lock (directed yield).
With CONFIG_PREEMPT="n" this can be implemented by the architecture without
common code changes. Powerpc already does this.
With CONFIG_PREEMPT="y" the lock loops are coded with _raw_spin_trylock,
_raw_read_trylock and _raw_write_trylock in kernel/spinlock.c. If the lock
could not be taken cpu_relax is called. A directed yield is not possible
because cpu_relax doesn't know anything about the lock. To be able to
yield the lock in favour of the current lock holder variants of cpu_relax
for spinlocks and rw-locks are needed. The new _raw_spin_relax,
_raw_read_relax and _raw_write_relax primitives differ from cpu_relax
insofar that they have an argument: a pointer to the lock structure.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Letting WARN_ON/WARN_ON_ONCE return the condition means that you could do
if (WARN_ON(blah)) {
handle_impossible_case
}
Rather than
if (unlikely(blah)) {
WARN_ON(1)
handle_impossible_case
}
I checked all the newly added WARN_ON_ONCE users and none of them test the
return status so we can still change it.
[akpm@osdl.org: warning fix]
[akpm@osdl.org: build fix]
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the changes necessary for shared page tables is to standardize the
pxx_page macros. pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address. pud_page and pgd_page, on the
other hand, return the kernel virtual address.
Shared page tables needs pud_page and pgd_page to return the actual page
structures. There are very few actual users of these functions, so it is
simple to standardize their usage.
Since this is basic cleanup, I am submitting these changes as a standalone
patch. Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They all contain the same thing. Instead, have a single generic one in
include/asm-generic, and permit an arch to override as needed.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.infradead.org/~dwmw2/hdroneline:
[HEADERS] One line per header in Kbuild files to reduce conflicts
Manual (trivial) conflict resolution in include/asm-s390/Kbuild
Ulrich Weigand found a bug with the current version of the
asm-powerpc/ptrace.h that prevents building at least the
SPU target version of gdb, since some ptrace opcodes are
not defined.
The problem seems to have originated in the merging of 32 and
64 bit versions of that file, the problem is that some opcodes
are only valid on 64 bit kernels, but are also used by 32 bit
programs, so they can't depends on the __powerpc64__ symbol.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This looks like cruft to me, these functions don't exist AFAICT,
and I can't see that it's possible to even enable DISCONTIGMEM on
powerpc anymore. CC'ing some folks who might know better, based on
the who-touched-it-last principle.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The stuff below cleans up the code attempting to remap the whole cpm2_immr
early, as well as places happily assuming that fact. This is more like the 2.4
legacy stuff, and is at least confusing and unclear now.
To keep the world comfortable, a new mechanism is introduced: before accessing
specific immr register/register set, one needs to map it, using cpm2_map(<reg>),
for instance, access to CPM command register will look like
volatile cpm_cpm2_t *cp = cpm2_map(im_cpm);
keeping the code clear, yet without "already defined somewhere" cpm2_immr.
So far, unmapping code is not implemented, but it's not a big deal to add it,
if the whole idea makes sense.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.
Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).
This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Driver core has been updated to make use of the new powerpc OF-inspired
platform devices, yet keeping compatibility to the vast board list from
ppc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Add wrapper around the rtas call to enable MMIO or DMA on a frozen pci
slot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This produces essentially the same code and will make the iSeries i/o
consolidation easier.
The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The io accessors insw_ns, outsw_ns, insl_ns and outsl_ns are unused
(except for one unnecessary use in drivers/net/3c509.c that is addressed
in a previous patch) and are only defined in powerpc/ppc, so remove them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add instrumentation for hypervisor calls on pseries. Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs. Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The performance monitor implementation (including CTRL register behaviour)
is just included in PPC v2 as an example, it's not truly part of the base.
It's actually a somewhat misleading feature, but I'll leave that be for
now: The presence of the register is not what the feature bit is used
for, but instead it's used to determine if it contains the runlatch
bit for idle reporting of the performance monitor. For alternative
implementations, the register might still exist but the bit might have
different meaning (or no meaning at all).
For now, split it off and don't include it in CPU_FTR_PPCAS_ARCH_V2_BASE.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is required to generate proper core files using kdump on ppc64.
Create a backup region of 64K size irrespective of the PAGE SIZE.
At present 32K was used as backup size. In the case of 64K page size,
second PT_LOAD segments starts at 32K and the first one is not page
aligned. __ioremap() (crash_dump.c) fails if pfn = 0 which is the
case for the second PT_LOAD segment. This is not an issue for 4K page
size because the the first page (32K backup) is copied to second
kernel memory and thus referencing with the second kernel pfn.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sys_[gs]et_robust_list() syscalls were wired up on PowerPC but
didn't work correctly because futex_atomic_cmpxchg_inatomic() wasn't
implemented. Implement it, based on __cmpxchg_u32().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These are build fixes that enable (for example) libata and the ide
code to actually build on iSeries. The associated hardware will never
be supported on legacy iSeries, so the code paths don't actually need
to work, but it is useful (especially for a combined kernel) if the
code can build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a problem introduced in 5db9fa9593.
The last_jiffy per-cpu variable is only 32 bits on 32-bit machines, but it
was being compared with a 64-bit quantity (tb_next_jiffy), which resulted in
time not advancing.
This fixes it by changing last_jiffy to be 64 bits on all platforms. With
this, we no longer need tb_last_stamp as a 32-bit version of tb_last_jiffy,
so this gets rid of tb_last_stamp and we just use tb_last_jiffy instead.
This also fixes a bug when the boot cpu is not online, because using
tb_last_stamp could have caused the wrong timebase origin value to be used
when calculating the time of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device-tree bugs on js20 with some versions of SLOF were causing the
interrupt for IDE to not be parsed correctly and fail to boot. This
patch adds a bit more sanity checking to the parser to detect some of
those errors and fail instead of returning bogus information. The
powerpc PCI code can then trigger a fallback that works on those
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.
This introduces CONFIG_MPIC_WEIRD. For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.
TSI108/109 PIC takes the first index of weird hardware information
table. :) The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.
The patch does not affect the behavior of standard mpic. If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.
[benh@kernel.crashing.org:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Keep from breaking 83xx arch/ppc build. Back up old school arch/powerpc/sysdev/ipic.[hc] to arch/ppc/syslib.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After going through the trouble of setting up the PIC base
address in the pic@40000 device tree node, use it instead
of the obsolete hard-coded value.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Several RTAS calls take a "config_addr" parameter, which is a particular
way of specifying a PCI busno, devfn and register number into a 32-bit word.
Currently these are open-coded, and I'll be adding another soon, replace
them with a helper that encapsulates the logic. Be more strict about masking
the busno too, just in case.
Booted on P5 LPAR.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2006-08-15 at 08:22 -0700, Dave Hansen wrote:
> kernel BUG in cache_free_debugcheck at mm/slab.c:2748!
Alright, this one is only triggered when slab debugging is enabled. The
slabs are assumed to be aligned on a HUGEPTE_TABLE_SIZE boundary. The free
path makes use of this assumption and uses the lowest nibble to pass around
an index into an array of kmem_cache pointers. With slab debugging turned
on, the slab is still aligned, but the "working" object pointer is not.
This would break the assumption above that a full nibble is available for
the PGF_CACHENUM_MASK.
The following patch reduces PGF_CACHENUM_MASK to cover only the two least
significant bits, which is enough to cover the current number of 4 pgtable
cache types. Then use this constant to mask out the appropriate part of
the huge pte pointer.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch rewrites mpc7448hpc2 board irq support according to the new
mpic device tree interface.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are two problems in the powerpc gettimeofday code which can
cause incorrect results to be returned.
The first is that there is a race between do_gettimeofday and the
timer interrupt:
1. do_gettimeofday does get_tb()
2. decrementer exception on boot cpu which runs timer_recalc_offset,
which also samples the timebase and updates the do_gtod structure
with a greater timebase value.
3. do_gettimeofday calls __do_gettimeofday, which leads to the
negative result from tb_val - temp_varp->tb_orig_stamp.
The second is caused by taking the boot cpu offline, which can cause
the value of tb_last_jiffy to be increased past the currently
available timebase, causing the same underflow as above.
[paulus@samba.org - define and use data_barrier() instead of mb().]
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kill host_set->next
Fix simplex support
Allow per platform setting of IDE legacy bases
Some of this can be tidied further later on, in particular all the
legacy port gunge belongs as a PCI quirk/PCI header decode to understand
the special legacy IDE rules in the PCI spec.
Longer term Jeff also wants to move the request_irq/free_irq out of core
which will make this even cleaner.
tj: folded in three followup patches - ata_piix-fix, broken-arch-fix
and fix-new-legacy-handling, and separated per-dev xfermask into
separate patch preceding this one. Folded in fixes are...
* ata_piix-fix: fix build failure due to host_set->next removal
* broken-arch-fix: add missing include/asm-*/libata-portmap.h
* fix-new-legacy-handling:
* In ata_pci_init_legacy_port(), probe_num was incorrectly
incremented during initialization of the secondary port and
probe_ent->n_ports was incorrectly fixed to 1.
* Both legacy ports ended up having the same hard_port_no.
* When printing port information, both legacy ports printed
the first irq.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
This adds a shadow buffer for the SLBs and regsiters it with PHYP.
Only the bolted SLB entries (top 3) are shadowed.
The SLB shadow buffer tells the hypervisor what the kernel needs to
have in the SLB for the kernel to be able to function. The hypervisor
can use this information to speed up partition context switches.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't have much in the way of doc comments, but some of those we do have
don't work because they start with "/***" or "/*", not "/**" which is what
kernel-doc requires.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticing the following might_sleep warning (dump_stack()) during kdump
testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs
will be calling rtas_set_indicator with interrupts disabled to remove
them from global interrupt queue.
BUG: sleeping function called from invalid context at
arch/powerpc/kernel/rtas.c:463
in_atomic():1, irqs_disabled():1
Call Trace:
[C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable)
[C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4
[C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c
[C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc
[C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134
[C00000000FFFBC40] [C00000000004539C]
.pseries_kexec_cpu_down_xics+0x74/0x8c
[C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188
[C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc
[C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130
[C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8
[C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c
[C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c
[C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4
[C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10
--- Exception: 501 at .plpar_hcall_norets+0x14/0x1c
LR = .pseries_dedicated_idle_sleep+0x190/0x1d4
[C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable)
[C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0
[C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c
To fix this issue, rtas_set_indicator_fast() is added so that will not
wait for RTAS 'busy' delay and this new function is used for kdump (in
xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and
xics_setup_cpu()).
Note that the platform architecture spec says that set-indicator
on the indicator we're using here is not permitted to return the
busy or extended busy status codes.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our pseries hcall interfaces are out of control:
plpar_hcall_norets
plpar_hcall
plpar_hcall_8arg_2ret
plpar_hcall_4out
plpar_hcall_7arg_7ret
plpar_hcall_9arg_9ret
Create 3 interfaces to cover all cases:
plpar_hcall_norets: 7 arguments no returns
plpar_hcall: 6 arguments 4 returns
plpar_hcall9: 9 arguments 9 returns
There are only 2 cases in the kernel that need plpar_hcall9, hopefully
we can keep it that way.
Pass in a buffer to stash return parameters so we avoid the &dummy1,
&dummy2 madness.
Signed-off-by: Anton Blanchard <anton@samba.org>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
