AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW+SJrBscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdtTfAEAg9TNQi+IAth1TuEfbsrO
ykB2PDEPD0wZnWh/sEIYhdAA/3zhYeqPq4X9PLhtRZQ2fJFE2Uw/4BTmSAqffD+L
2ZwG
=MA3z
-----END PGP SIGNATURE-----
Merge tag 'led-fixes-for-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"All three fixes are related to the newly added pattern trigger:
- remove mutex_lock() from timer callback, which would trigger
problems related to sleeping in atomic context, the removal is
harmless since mutex protection turned out to be redundant in this
case
- fix pattern parsing to properly handle intervals with brightness == 0
- fix typos in the ABI documentation"
* tag 'led-fixes-for-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Documentation: ABI: led-trigger-pattern: Fix typos
leds: trigger: Fix sleeping function called from invalid context
Fix pattern handling optimalization
Most of the ARM platforms used v2 OPP bindings to support big-little
configurations. This arm_big_little_dt binding is incomplete and was
never used.
Commit f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
removed the driver supporting this binding, but the binding was left
unnoticed, so let's get rid of it now.
Fixes: f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a typo in the admin-guide documentation for cpufreq.
Signed-off-by: Zhao Wei Liew <zhaoweiliew@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The order in which the frequencies are displayed in cpufreq stats
depends on the order in which the frequencies were sorted in the
frequency table provided to cpufreq core by the cpufreq driver. They can
be completely unsorted as well.
The documentation's claim that the stats will be sorted in descending
order is hence incorrect and here is an attempt to fix it.
Reported-by: Pavel <pavel2000@ngs.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 5-level paging the LDT remap area is placed in the middle of the KASLR
randomization region and it can overlap with the direct mapping, the
vmalloc or the vmap area.
The LDT mapping is per mm, so it cannot be moved into the P4D page table
next to the CPU_ENTRY_AREA without complicating PGD table allocation for
5-level paging.
The 4 PGD slot gap just before the direct mapping is reserved for
hypervisors, so it cannot be used.
Move the direct mapping one slot deeper and use the resulting gap for the
LDT remap area. The resulting layout is the same for 4 and 5 level paging.
[ tglx: Massaged changelog ]
Fixes: f55f0501cb ("x86/pti: Put the LDT in its own PGD if PTI is on")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-2-kirill.shutemov@linux.intel.com
The format fields in struct v4l2_format were otherwise documented but the
meta field was missing. Document it.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For allocating XArrays, it makes sense to distinguish beteen erasing an
entry and storing NULL. Storing NULL keeps the index allocated with a
NULL pointer associated with it while xa_erase() frees the index. Some
existing IDR users rely on this ability.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
These convenience wrappers disable interrupts while taking the spinlock.
A number of drivers would otherwise have to open-code these functions.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
The xa_reserve() function was a little unusual in that it attempted to
be callable for all kinds of locking scenarios. Make it look like the
other APIs with __xa_reserve, xa_reserve_bh and xa_reserve_irq variants.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Fix RZ/G2E part number from its description.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Full filesystem authentication feature,
UBIFS is now able to have the whole filesystem structure
authenticated plus user data encrypted and authenticated.
- Minor cleanups
-----BEGIN PGP SIGNATURE-----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=lq2m
-----END PGP SIGNATURE-----
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Dt-bindings doc for gx6605s SOC's system timer.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Dt-bingdings doc for C-SKY SMP system setting.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
-----BEGIN PGP SIGNATURE-----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=0zM4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20181102' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"The biggest part of this pull request is the revert of the blkcg
cleanup series. It had one fix earlier for a stacked device issue, but
another one was reported. Rather than play whack-a-mole with this,
revert the entire series and try again for the next kernel release.
Apart from that, only small fixes/changes.
Summary:
- Indentation fixup for mtip32xx (Colin Ian King)
- The blkcg cleanup series revert (Dennis Zhou)
- Two NVMe fixes. One fixing a regression in the nvme request
initialization in this merge window, causing nvme-fc to not work.
The other is a suspend/resume p2p resource issue (James, Keith)
- Fix sg discard merge, allowing us to merge in cases where we didn't
before (Jianchao Wang)
- Call rq_qos_exit() after the queue is frozen, preventing a hang
(Ming)
- Fix brd queue setup, fixing an oops if we fail setting up all
devices (Ming)"
* tag 'for-linus-20181102' of git://git.kernel.dk/linux-block:
nvme-pci: fix conflicting p2p resource adds
nvme-fc: fix request private initialization
blkcg: revert blkcg cleanups series
block: brd: associate with queue until adding disk
block: call rq_qos_exit() after queue is frozen
mtip32xx: clean an indentation issue, remove extraneous tabs
block: fix the DISCARD request merge
This series contains a number of improvements to existing drivers, such
as LPSS. Some drivers, such as renesas-tpu and rcar get support for more
SoC generations. To round things off this fixes an issue with the sysfs
interface.
-----BEGIN PGP SIGNATURE-----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=AECG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This series contains a number of improvements to existing drivers,
such as LPSS. Some drivers, such as renesas-tpu and rcar get support
for more SoC generations. To round things off this fixes an issue with
the sysfs interface"
* tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: Only set update bit if we are actually changing the settings
pwm: lpss: Force runtime-resume on suspend on Cherry Trail
pwm: Enable TI ECAP driver for ARCH_K3
dt-bindings: pwm: tiecap: Add TI AM654 SoC specific compatible
dt-bindings: pwm: rcar: Add r8a774a1 support
pwm: Send a uevent on the pwmchip device upon channel sysfs (un)export
Revert "pwm: Set class for exported channels in sysfs"
dt-bindings: pwm: renesas-tpu: Document r8a7744 support
dt-bindings: pwm: rcar: Add r8a7744 support
dt-bindings: pwm: renesas: tpu: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: pwm-rcar: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: tpu: Fix "compatible" prop description
pwm: Use SPDX identifier for Renesas drivers
pwm: lpss: Add get_state callback
pwm: lpss: Release runtime-pm reference from the driver's remove callback
pwm: lpss: Check PWM powerstate after resume on Cherry Trail devices
pwm: lpss: Move struct pwm_lpss_chip definition to the header file
pwm: lpss: Add ACPI HID for second PWM controller on Cherry Trail devices
ACPI / PM: Export acpi_device_get_power() for use by modular build drivers
pwm: tegra: Remove gratuituous blank line
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb2+C2AAoJEAx081l5xIa+tUYP/060xa9VeKe0M11fMCCkchNV
TQfPQ8avy2/Tt9Mlly/XPMuBZ6FCTVBsseCxIdzl4rZAfm0SDVaTB4Z7XBBplXkv
R50Je95Fyv0/lnUbagI5qRtc+O6xdkuNIMHWlRRWGlCEbFE2atey9R2yiq/1q2J9
4NcGjykJ7d1vCgMm/9/iV4pLrxrRSxvizO4mS+SQpJ/0fEwJSZSvKdKp9LU/LTgx
qZGSBegPkR+j6znsMkuPYxQtMrhz+Pr49qp7Qm6wQV/K2Y0z7CoHZFikvpMp38i5
MQfYE0yDN3pKm5THt+RjV8laPIpnh2z8bcotUCGcjFWtGHQBfyQ4IaXkDPujcD6m
vRm4hhxP9DvNCq5eWFz3vU2n8NWf54BYFF8dPxcoghRkE6VB2CGpr+o9dzxX16QJ
oEi2Ak3G7RXa8Hn/C9EOSs7yijjKD8GZ8gR5osmI10EitIH7mrG9Xghts5XlcIJj
Ls30t0jPavO+t8V2/1HYP2vfSNvi/X953+pQIdN8Rk2vp0ziFdstzLg6ai8E1Hvl
jyvOF3/xstwIP8nFvYaNHkly2iVRC3rgj4GDncSe2U6kt8N4/aA+FemUwXJKBbFN
hVwPZuSlrCw5TE7tO3ulJon4uAWH5WO/gIOMn0+e+pBLJtUXQtWAR+JC2D+RDZO9
V+V7GuHIbIV6xarCwLjx
=5lmL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
Rework the vfs_clone_file_range and vfs_dedupe_file_range infrastructure to use
a common .remap_file_range method and supply generic bounds and sanity checking
functions that are shared with the data write path. The current VFS
infrastructure has problems with rlimit, LFS file sizes, file time stamps,
maximum filesystem file sizes, stripping setuid bits, etc and so they are
addressed in these commits.
We also introduce the ability for the ->remap_file_range methods to return short
clones so that clones for vfs_copy_file_range() don't get rejected if the entire
range can't be cloned. It also allows filesystems to sliently skip deduplication
of partial EOF blocks if they are not capable of doing so without requiring
errors to be thrown to userspace.
All existing filesystems are converted to user the new .remap_file_range method,
and both XFS and ocfs2 are modified to make use of the new generic checking
infrastructure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CE/A
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.20-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull vfs dedup fixes from Dave Chinner:
"This reworks the vfs data cloning infrastructure.
We discovered many issues with these interfaces late in the 4.19 cycle
- the worst of them (data corruption, setuid stripping) were fixed for
XFS in 4.19-rc8, but a larger rework of the infrastructure fixing all
the problems was needed. That rework is the contents of this pull
request.
Rework the vfs_clone_file_range and vfs_dedupe_file_range
infrastructure to use a common .remap_file_range method and supply
generic bounds and sanity checking functions that are shared with the
data write path. The current VFS infrastructure has problems with
rlimit, LFS file sizes, file time stamps, maximum filesystem file
sizes, stripping setuid bits, etc and so they are addressed in these
commits.
We also introduce the ability for the ->remap_file_range methods to
return short clones so that clones for vfs_copy_file_range() don't get
rejected if the entire range can't be cloned. It also allows
filesystems to sliently skip deduplication of partial EOF blocks if
they are not capable of doing so without requiring errors to be thrown
to userspace.
Existing filesystems are converted to user the new remap_file_range
method, and both XFS and ocfs2 are modified to make use of the new
generic checking infrastructure"
* tag 'xfs-4.20-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (28 commits)
xfs: remove [cm]time update from reflink calls
xfs: remove xfs_reflink_remap_range
xfs: remove redundant remap partial EOF block checks
xfs: support returning partial reflink results
xfs: clean up xfs_reflink_remap_blocks call site
xfs: fix pagecache truncation prior to reflink
ocfs2: remove ocfs2_reflink_remap_range
ocfs2: support partial clone range and dedupe range
ocfs2: fix pagecache truncation prior to reflink
ocfs2: truncate page cache for clone destination file before remapping
vfs: clean up generic_remap_file_range_prep return value
vfs: hide file range comparison function
vfs: enable remap callers that can handle short operations
vfs: plumb remap flags through the vfs dedupe functions
vfs: plumb remap flags through the vfs clone functions
vfs: make remap_file_range functions take and return bytes completed
vfs: remap helper should update destination inode metadata
vfs: pass remap flags to generic_remap_checks
vfs: pass remap flags to generic_remap_file_range_prep
vfs: combine the clone and dedupe into a single remap_file_range
...
This is an effort to disentangle the include/linux/compiler*.h headers
and bring them up to date.
The main idea behind the series is to use feature checking macros
(i.e. __has_attribute) instead of compiler version checks (e.g. GCC_VERSION),
which are compiler-agnostic (so they can be shared, reducing the size
of compiler-specific headers) and version-agnostic.
Other related improvements have been performed in the headers as well,
which on top of the use of __has_attribute it has amounted to a significant
simplification of these headers (e.g. GCC_VERSION is now only guarding
a few non-attribute macros).
This series should also help the efforts to support compiling the kernel
with clang and icc. A fair amount of documentation and comments have also
been added, clarified or removed; and the headers are now more readable,
which should help kernel developers in general.
The series was triggered due to the move to gcc >= 4.6. In turn, this series
has also triggered Sparse to gain the ability to recognize __has_attribute
on its own.
Finally, the __nonstring variable attribute series has been also applied
on top; plus two related patches from Nick Desaulniers for unreachable()
that came a bit afterwards.
-----BEGIN PGP SIGNATURE-----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=Y8WB
-----END PGP SIGNATURE-----
Merge tag 'compiler-attributes-for-linus-4.20-rc1' of https://github.com/ojeda/linux
Pull compiler attribute updates from Miguel Ojeda:
"This is an effort to disentangle the include/linux/compiler*.h headers
and bring them up to date.
The main idea behind the series is to use feature checking macros
(i.e. __has_attribute) instead of compiler version checks (e.g.
GCC_VERSION), which are compiler-agnostic (so they can be shared,
reducing the size of compiler-specific headers) and version-agnostic.
Other related improvements have been performed in the headers as well,
which on top of the use of __has_attribute it has amounted to a
significant simplification of these headers (e.g. GCC_VERSION is now
only guarding a few non-attribute macros).
This series should also help the efforts to support compiling the
kernel with clang and icc. A fair amount of documentation and comments
have also been added, clarified or removed; and the headers are now
more readable, which should help kernel developers in general.
The series was triggered due to the move to gcc >= 4.6. In turn, this
series has also triggered Sparse to gain the ability to recognize
__has_attribute on its own.
Finally, the __nonstring variable attribute series has been also
applied on top; plus two related patches from Nick Desaulniers for
unreachable() that came a bit afterwards"
* tag 'compiler-attributes-for-linus-4.20-rc1' of https://github.com/ojeda/linux:
compiler-gcc: remove comment about gcc 4.5 from unreachable()
compiler.h: update definition of unreachable()
Compiler Attributes: ext4: remove local __nonstring definition
Compiler Attributes: auxdisplay: panel: use __nonstring
Compiler Attributes: enable -Wstringop-truncation on W=1 (gcc >= 8)
Compiler Attributes: add support for __nonstring (gcc >= 8)
Compiler Attributes: add MAINTAINERS entry
Compiler Attributes: add Doc/process/programming-language.rst
Compiler Attributes: remove uses of __attribute__ from compiler.h
Compiler Attributes: KENTRY used twice the "used" attribute
Compiler Attributes: use feature checks instead of version checks
Compiler Attributes: add missing SPDX ID in compiler_types.h
Compiler Attributes: remove unneeded sparse (__CHECKER__) tests
Compiler Attributes: homogenize __must_be_array
Compiler Attributes: remove unneeded tests
Compiler Attributes: always use the extra-underscores syntax
Compiler Attributes: remove unused attributes
Pull keys updates from James Morris:
"Provide five new operations in the key_type struct that can be used to
provide access to asymmetric key operations. These will be implemented
for the asymmetric key type in a later patch and may refer to a key
retained in RAM by the kernel or a key retained in crypto hardware.
int (*asym_query)(const struct kernel_pkey_params *params,
struct kernel_pkey_query *info);
int (*asym_eds_op)(struct kernel_pkey_params *params,
const void *in, void *out);
int (*asym_verify_signature)(struct kernel_pkey_params *params,
const void *in, const void *in2);
Since encrypt, decrypt and sign are identical in their interfaces,
they're rolled together in the asym_eds_op() operation and there's an
operation ID in the params argument to distinguish them.
Verify is different in that we supply the data and the signature
instead and get an error value (or 0) as the only result on the
expectation that this may well be how a hardware crypto device may
work"
* 'next-keys2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (22 commits)
KEYS: asym_tpm: Add support for the sign operation [ver #2]
KEYS: asym_tpm: Implement tpm_sign [ver #2]
KEYS: asym_tpm: Implement signature verification [ver #2]
KEYS: asym_tpm: Implement the decrypt operation [ver #2]
KEYS: asym_tpm: Implement tpm_unbind [ver #2]
KEYS: asym_tpm: Add loadkey2 and flushspecific [ver #2]
KEYS: Move trusted.h to include/keys [ver #2]
KEYS: trusted: Expose common functionality [ver #2]
KEYS: asym_tpm: Implement encryption operation [ver #2]
KEYS: asym_tpm: Implement pkey_query [ver #2]
KEYS: Add parser for TPM-based keys [ver #2]
KEYS: asym_tpm: extract key size & public key [ver #2]
KEYS: asym_tpm: add skeleton for asym_tpm [ver #2]
crypto: rsa-pkcs1pad: Allow hash to be optional [ver #2]
KEYS: Implement PKCS#8 RSA Private Key parser [ver #2]
KEYS: Implement encrypt, decrypt and sign for software asymmetric key [ver #2]
KEYS: Allow the public_key struct to hold a private key [ver #2]
KEYS: Provide software public key query function [ver #2]
KEYS: Make the X.509 and PKCS7 parsers supply the sig encoding type [ver #2]
KEYS: Provide missing asymmetric key subops for new key type ops [ver #2]
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCW9tlWwAKCRDh3BK/laaZ
PEszAQDnwCMuh4WwhmS4d4X9/rLwzxBqFcHbBUMxvUSpD2LSvQD/fbV3EVkcTGUc
DVfV2e9Zdy2vq36fcR3EMa1oUGNzpgc=
=oscW
-----END PGP SIGNATURE-----
Merge tag 'ovl-update-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"A mix of fixes and cleanups"
* tag 'ovl-update-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: automatically enable redirect_dir on metacopy=on
ovl: check whiteout in ovl_create_over_whiteout()
ovl: using posix_acl_xattr_size() to get size instead of posix_acl_to_xattr()
ovl: abstract ovl_inode lock with a helper
ovl: remove the 'locked' argument of ovl_nlink_{start,end}
ovl: relax requirement for non null uuid of lower fs
ovl: fold copy-up helpers into callers
ovl: untangle copy up call chain
ovl: relax permission checking on underlying layers
ovl: fix recursive oi->lock in ovl_link()
vfs: fix FIGETBSZ ioctl on an overlayfs file
ovl: clean up error handling in ovl_get_tmpfile()
ovl: fix error handling in ovl_verify_set_fh()
- Fix cpu node iterator for powerpc systems
- Clarify ARM CPU binding 'capacities-dmips-mhz' property calculations
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAlvbbZAQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw7jbD/4ssXLQHvj0z7wh05Bi7xtkHjjSRj6ymTMQ
KfYHMOrjbA5bGG/zvRiYPyXM1y06nMPlbMqWQZdtXweFK5fKFQ5J7+x99cAaFPlJ
fRbhwVSMjiTThrupcWrt8a3DIxTdqHIxtVwALCETkXIQb54rffEG2uEO9SnmccQW
gFyAga2fcUvXj+5UyFHFZVvQWs9ZhQt4sb7UyaXCZI3p9L7KLzL/uGTtp/bcXQ+7
D3f6P0rq2YUSWvE9QxQvnoPopbICG4+PFeK70owCgNUFrnfmh+r2TnAvcMzZOgI4
Qj8NL+RIqXxP5S7oS2OzHifNnv861HwkbSo/sQR1QFcffkFcBrqPoFMFmvqGagRX
CGktqt52+7xtKngfnMXvzy+xFcxAch1MHUxSCuPLzzyg5e/EFBKb9unXGuZ3cgyV
kO9f2xDRt72VqV4C8bvBs3QNqc9MUVd/qfmz0ZGeJrsQ6snMffrOhPlNvLFU1zuj
HoPZuCji8xGn++Mx0/YpECc+JUX4bnPL1ZoY0rDrgqfshfIjN7BB3StteHIY7rak
PxwhTjpIIOl6W2w8BqcTy54xLZeo2D3O1fxK4SG5IS8AwD3xLOaMI6YcRMz1zehE
ELw7zfNBFAlXfXkUNRHqJtNXCFwOTrFaTaQd2EC90BUMj+7YJlkDVj3PIHlFZLMR
ulF4/8AcPQ==
=AG4j
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- fix cpu node iterator for powerpc systems
- clarify ARM CPU binding 'capacities-dmips-mhz' property calculations
* tag 'devicetree-fixes-for-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Fix cpu node iterator to not ignore disabled cpu nodes
dt-bindings: arm: Explain capacities-dmips-mhz calculations in example
Current behavior is to automatically disable metacopy if redirect_dir is
not enabled and proceed with the mount.
If "metacopy=on" mount option was given, then this behavior can confuse the
user: no mount failure, yet metacopy is disabled.
This patch makes metacopy=on imply redirect_dir=on.
The converse is also true: turning off full redirect with redirect_dir=
{off|follow|nofollow} will disable metacopy.
If both metacopy=on and redirect_dir={off|follow|nofollow} is specified,
then mount will fail, since there's no way to correctly resolve the
conflict.
Reported-by: Daniel Walsh <dwalsh@redhat.com>
Fixes: d5791044d2 ("ovl: Provide a mount option metacopy=on/off...")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
- Introduces the stackleak gcc plugin ported from grsecurity by Alexander
Popov, with x86 and arm64 support.
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=Ks6B
-----END PGP SIGNATURE-----
Merge tag 'stackleak-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull stackleak gcc plugin from Kees Cook:
"Please pull this new GCC plugin, stackleak, for v4.20-rc1. This plugin
was ported from grsecurity by Alexander Popov. It provides efficient
stack content poisoning at syscall exit. This creates a defense
against at least two classes of flaws:
- Uninitialized stack usage. (We continue to work on improving the
compiler to do this in other ways: e.g. unconditional zero init was
proposed to GCC and Clang, and more plugin work has started too).
- Stack content exposure. By greatly reducing the lifetime of valid
stack contents, exposures via either direct read bugs or unknown
cache side-channels become much more difficult to exploit. This
complements the existing buddy and heap poisoning options, but
provides the coverage for stacks.
The x86 hooks are included in this series (which have been reviewed by
Ingo, Dave Hansen, and Thomas Gleixner). The arm64 hooks have already
been merged through the arm64 tree (written by Laura Abbott and
reviewed by Mark Rutland and Will Deacon).
With VLAs having been removed this release, there is no need for
alloca() protection, so it has been removed from the plugin"
* tag 'stackleak-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: Drop unneeded stackleak_check_alloca()
stackleak: Allow runtime disabling of kernel stack erasing
doc: self-protection: Add information about STACKLEAK feature
fs/proc: Show STACKLEAK metrics in the /proc file system
lkdtm: Add a test for STACKLEAK
gcc-plugins: Add STACKLEAK plugin for tracking the kernel stack
x86/entry: Add STACKLEAK erasing the kernel stack at the end of syscalls
Pull i2c fixes from Wolfram Sang:
"I2C has a core bugfix & cleanup as well as an ID addition and
MAINTAINERS update for you"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer for IMX LPI2C driver
dt-bindings: i2c: i2c-imx-lpi2c: add imx8qxp compatible string
i2c: Clear client->irq in i2c_device_remove
i2c: Remove unnecessary call to irq_find_mapping
Pull networking fixes from David Miller:
1) BPF verifier fixes from Daniel Borkmann.
2) HNS driver fixes from Huazhong Tan.
3) FDB only works for ethernet devices, reject attempts to install FDB
rules for others. From Ido Schimmel.
4) Fix spectre V1 in vhost, from Jason Wang.
5) Don't pass on-stack object to irq_set_affinity_hint() in mvpp2
driver, from Marc Zyngier.
6) Fix mlx5e checksum handling when RXFCS is enabled, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (49 commits)
openvswitch: Fix push/pop ethernet validation
net: stmmac: Fix stmmac_mdio_reset() when building stmmac as modules
bpf: test make sure to run unpriv test cases in test_verifier
bpf: add various test cases to test_verifier
bpf: don't set id on after map lookup with ptr_to_map_val return
bpf: fix partial copy of map_ptr when dst is scalar
libbpf: Fix compile error in libbpf_attach_type_by_name
kselftests/bpf: use ping6 as the default ipv6 ping binary if it exists
selftests: mlxsw: qos_mc_aware: Add a test for UC awareness
selftests: mlxsw: qos_mc_aware: Tweak for min shaper
mlxsw: spectrum: Set minimum shaper on MC TCs
mlxsw: reg: QEEC: Add minimum shaper fields
net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()
net: hns3: bugfix for rtnl_lock's range in the hclge_reset()
net: hns3: bugfix for handling mailbox while the command queue reinitialized
net: hns3: fix incorrect return value/type of some functions
net: hns3: bugfix for hclge_mdio_write and hclge_mdio_read
net: hns3: bugfix for is_valid_csq_clean_head()
net: hns3: remove unnecessary queue reset in the hns3_uninit_all_ring()
net: hns3: bugfix for the initialization of command queue's spin lock
...
Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86 as
they are closely coupled with other drivers in this location.
Improve _init* usage for acerhdf and fix some usage issues with messages
and module parameters.
Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
Notify intel_telemetry users when IPC1 device is not enabled.
Update various drivers with new laptop model IDs.
Update several intel drivers to use SPDX identifers and order headers
alphabetically.
The following is an automated git shortlog grouped by driver:
Add Intel AtomISP2 dummy / power-management driver:
- Add Intel AtomISP2 dummy / power-management driver
lg-laptop:
- Add LG Gram laptop special features driver
HID:
- asus: only support backlight when it's not driven by WMI
MAINTAINERS:
- intel_telemetry: Update maintainers info
- intel_pmc_core: Update MAINTAINERS
- Update maintainer for dcdbas and dell_rbu
- Use my infradead account exclusively for PDx86 work
acerhdf:
- restructure to allow large BIOS table be __initconst
- mark appropriate content with __init prefix
- Add BIOS entry for Gateway LT31 v1.3307
- Remove cut-and-paste trap from instructions
- Enable ability to list supported systems
- clarify modinfo messages for BIOS override
asus-wmi:
- export function for evaluating WMI methods
- Only notify kbd LED hw_change by fn-key pressed
- Simplify the keyboard brightness updating process
firmware:
- dcdbas: include linux/io.h
- dcdbas: Move dcdbas to drivers/platform/x86
- dell_rbu: Move dell_rbu to drivers/platform/x86
- dcdbas: Add support for WSMT ACPI table
- dell_rbu: Make payload memory uncachable
ideapad-laptop:
- Add Y530-15ICH to no_hw_rfkill
- Use __func__ instead of read_ec_cmd in pr_err
intel-hid:
- Convert to use SPDX identifier
intel-ips:
- Convert to use SPDX identifier
intel-rst:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-smartconnect:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-wmi-thunderbolt:
- Add dynamic debugging
- Convert to use SPDX identifier
intel_bxtwc_tmu:
- Convert to use SPDX identifier
intel_cht_int33fe:
- Convert to use SPDX identifier
intel_chtdc_ti_pwrbtn:
- Add SPDX identifier
intel_int0002_vgpio:
- Convert to use SPDX identifier
- Implement irq_set_wake
- Enable the driver on Bay Trail platforms
intel_menlow:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_mid_powerbtn:
- Convert to use SPDX identifier
- Remove unnecessary init.h inclusion
- Get rid of custom ICPU() macro
intel_mid_thermal:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_oaktrail:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_pmc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_punit_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_scu_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_telemetry:
- Get rid of custom macro
- report debugfs failure
- Convert to use SPDX identifier
intel_turbo_max_3:
- Convert to use SPDX identifier
- Sort headers alphabetically
mlx-platform:
- Properly use mlxplat_mlxcpld_msn201x_items
touchscreen_dmi:
- Add min-x and min-y settings for various models
- Add info for the Onda V80 Plus v3 tablet
- Add info for the Trekstor Primetab T13B tablet
- Add info for the Trekstor Primebook C11 convertible
tracing:
- Trivia spelling fix containerof() -> container_of()
wmi:
- declare device_type structure as constant
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJb2mDCAAoJEKbMaAwKp364KdkH/Rar8cenw7uFeVzT5o4fGzTn
0Oo1Pnwh+hPgmQwmf8O/mHsa/1Zb9nX4nNLU/ysDUjAAZ9wZLoB57HlImQquPA74
c8lXTz5MVF140WB1f1Ck5PmeonJR2Xve7HTYCoBmGo71jOxHxCgJbp1Giiho0Imd
3NXzzahEnAiy/L5PhqqYTmIfTeAHQ2Fo7GkHCjMnS20FP2fBtvPrc7db03F+FZ4y
QTfbT0oR42NdeW21AbCRGY3P47axB3xDJX4LOYrb4uo4CIzd1yatlHk407NRRyv8
pab6aeJR23FouA/tcvv+T36D3vqRw78e6BWdoyowWOd7CUOgjtSC3lKGzfT6hSY=
=0BDZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
as they are closely coupled with other drivers in this location.
- Improve _init* usage for acerhdf and fix some usage issues with
messages and module parameters.
- Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
- Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
- Notify intel_telemetry users when IPC1 device is not enabled.
- Update various drivers with new laptop model IDs.
- Update several intel drivers to use SPDX identifers and order headers
alphabetically.
* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
HID: asus: only support backlight when it's not driven by WMI
platform/x86: asus-wmi: export function for evaluating WMI methods
platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
platform/x86: wmi: declare device_type structure as constant
platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
platform/x86: Add Intel AtomISP2 dummy / power-management driver
platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
platform/x86: intel_telemetry: Get rid of custom macro
platform/x86: intel_telemetry: report debugfs failure
MAINTAINERS: intel_telemetry: Update maintainers info
platform/x86: Add LG Gram laptop special features driver
platform/x86: asus-wmi: Simplify the keyboard brightness updating process
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
MAINTAINERS: intel_pmc_core: Update MAINTAINERS
firmware: dcdbas: include linux/io.h
platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
...
The last user of cc-fullversion was removed by commit f2910f0e68
("powerpc: remove old GCC version checks").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As commit 911a91c39c ("kconfig: rename silentoldconfig to
syncconfig") announced, it is time for the removal.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- a series that fixes some old memory allocation issues in libceph
(myself). We no longer allocate memory in places where allocation
failures cannot be handled and BUG when the allocation fails.
- support for copy_file_range() syscall (Luis Henriques). If size and
alignment conditions are met, it leverages RADOS copy-from operation.
Otherwise, a local copy is performed.
- a patch that reduces memory requirement of ceph_sync_read() from the
size of the entire read to the size of one object (Zheng Yan).
- fallocate() syscall is now restricted to FALLOC_FL_PUNCH_HOLE (Luis
Henriques)
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlvZ6AcTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi8H+B/9V/QB1BX5Q2DvkS3mcLNI2NphrppaD
VBuviwoIzaBm1paCrx40J/pCtsK1Fybl5dBAh1W0SDxEGR8JUA8GJw+oemtOS6pZ
DwjOF9S7uhzf5M3nQ9SvAbIudBISMZQRi22Y8fWs3k+yaECIz1J/pe7RiKo/GBAB
NnlbrZ1AYSB02chchVCSmWTApeIRp9JXnaM9xLMJWGVLL/vONjt3ltJ/w9haGYz8
FPFLPFeWobWqFElnOUomxU8Cv84DgPtH8si0UAn16jveractpFJWO4X6LDs/ZYDk
/MccfsB3EK9BCJdLJMoI0/lXxE33z3/MehmJDs9xGSX/N4N7UTF8Ve1b
=U91e
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.20-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"The highlights are:
- a series that fixes some old memory allocation issues in libceph
(myself). We no longer allocate memory in places where allocation
failures cannot be handled and BUG when the allocation fails.
- support for copy_file_range() syscall (Luis Henriques). If size and
alignment conditions are met, it leverages RADOS copy-from
operation. Otherwise, a local copy is performed.
- a patch that reduces memory requirement of ceph_sync_read() from
the size of the entire read to the size of one object (Zheng Yan).
- fallocate() syscall is now restricted to FALLOC_FL_PUNCH_HOLE (Luis
Henriques)"
* tag 'ceph-for-4.20-rc1' of git://github.com/ceph/ceph-client: (25 commits)
ceph: new mount option to disable usage of copy-from op
ceph: support copy_file_range file operation
libceph: support the RADOS copy-from operation
ceph: add non-blocking parameter to ceph_try_get_caps()
libceph: check reply num_data_items in setup_request_data()
libceph: preallocate message data items
libceph, rbd, ceph: move ceph_osdc_alloc_messages() calls
libceph: introduce alloc_watch_request()
libceph: assign cookies in linger_submit()
libceph: enable fallback to ceph_msg_new() in ceph_msgpool_get()
ceph: num_ops is off by one in ceph_aio_retry_work()
libceph: no need to call osd_req_opcode_valid() in osd_req_encode_op()
ceph: set timeout conditionally in __cap_delay_requeue
libceph: don't consume a ref on pagelist in ceph_msg_data_add_pagelist()
libceph: introduce ceph_pagelist_alloc()
libceph: osd_req_op_cls_init() doesn't need to take opcode
libceph: bump CEPH_MSG_MAX_DATA_LEN
ceph: only allow punch hole mode in fallocate
ceph: refactor ceph_sync_read()
ceph: check if LOOKUPNAME request was aborted when filling trace
...
because of summer time holidays/vacations. The biggest change in the diffstat
is in the Qualcomm clk driver, where they got support for CPUs and handful of
SoCs. After that, the at91 driver got a major rewrite for newer DT bindings
that should make things easier going forward and the TI code moved to a
clockdomain based design. The long tail is mostly small driver updates for
newer clks and some simpler SoC clock drivers such as the Hisilicon and imx
support.
In the core framework, we only have two small changes this time. One is a new
clk API to get all clks for a device with the bulk clk APIs. This allows
drivers that don't care about doing anything besides turning on all the clks to
just clk_get() them all and turn them on. The other change is the beginning of
a way to support save and restore of clk settings in the clk framework. TI is
the only user right now, but we will want to expand upon this design in the
future to support more save and restore of clk registers. At least this gets
us started and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes
-----BEGIN PGP SIGNATURE-----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=V5aK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time it looks like a quieter release cycle in the clk tree. I
guess that's because of summer time holidays/vacations. The biggest
change in the diffstat is in the Qualcomm clk driver, where they got
support for CPUs and handful of SoCs. After that, the at91 driver got
a major rewrite for newer DT bindings that should make things easier
going forward and the TI code moved to a clockdomain based design.
The long tail is mostly small driver updates for newer clks and some
simpler SoC clock drivers such as the Hisilicon and imx support.
In the core framework, we only have two small changes this time.
One is a new clk API to get all clks for a device with the bulk clk
APIs. This allows drivers that don't care about doing anything besides
turning on all the clks to just clk_get() them all and turn them on.
The other change is the beginning of a way to support save and restore
of clk settings in the clk framework. TI is the only user right now,
but we will want to expand upon this design in the future to support
more save and restore of clk registers. At least this gets us started
and works well enough for one SoC, but there's more work in the
future.
Core:
- clk_bulk_get_all() API and friends to get all the clks for a device
- Basic clk state save/restore hooks
New Drivers:
- Renesas RZ/A2 (R7S9210) SoC, including early clocks
- Rensas RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs
- Rensas RZ/G2M (r8a774a1) SoC
- Qualcomm Krait CPU clk support
- Qualcomm QCS404 GCC support
- Qualcomm SDM660 GCC support
- Qualcomm SDM845 camera clock controller
- Ingenic jz4725b CGU
- Hisilicon 3670 SoC support
- TI SCI clks on K3 SoCs
- iMX6 MMDC clks
- Reset Controller (RMU) support for Actions Semi Owl S900 and S700 SoCs
Updates:
- Rework at91 PMC clock driver for new DT bindings
- Nvidia Tegra clk driver MBIST workaround fix
- S2RAM support for Marvell mvebu periph clks
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
- Add support for CMT timer clocks on R-Car V3H
- Add support for SHDI and various timer clocks on R-Car V3M
- Improve OSC and RCLK (watchdog) handling on R-Car Gen3 SoCs
- Amlogic clk-pll driver improvements and updates
- Amlogic axg audio controller system clocks
- Register Amlogic meson8b clock controller early
- Add support for SATA and Fine Display Processor (FDP) clocks on R-Car M3-N
- Consolidation of system suspend related code in Exynos, S5P, S3C SoC clk drivers
- Fixes for system suspend support on Exynos542x (Odroid boards) and Exynos5433 SoC
- Remove obsoleted Exynos4212 ISP clock definitions
- Migrated TI am3/4/5 and dra7 SoCs to clockdomain based design
- TI RTC+DDR sleep mode support for clock save/restore
- Allwinner A64 display engine support and fixes
- Allwinner A83t display engine support and fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (186 commits)
clk: qcom: Remove unused arrays in SDM845 GCC
clk: fixed-rate: fix of_node_get-put imbalance
clk: s2mps11: Add used attribute to s2mps11_dt_match
clk: qcom: gcc-sdm660: Add MODULE_LICENSE
clk: qcom: Add safe switch hook for krait mux clocks
dt-bindings: clock: Document qcom,krait-cc
clk: qcom: Add Krait clock controller driver
dt-bindings: arm: Document qcom,kpss-gcc
clk: qcom: Add KPSS ACC/GCC driver
clk: qcom: Add support for Krait clocks
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add MSM8960/APQ8064's HFPLLs
dt-bindings: clock: Document qcom,hfpll
clk: qcom: Add HFPLL driver
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
ARM: Add Krait L2 register accessor functions
clk: imx6q: add mmdc0 ipg clock
clk: imx6sl: add mmdc ipg clocks
clk: imx6sll: add mmdc1 ipg clock
clk: imx6sx: add mmdc1 ipg clock
...
-----BEGIN PGP SIGNATURE-----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=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
Merge more updates from Andrew Morton:
- the rest of MM
- lib/bitmap updates
- hfs updates
- fatfs updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
mm/gup.c: fix __get_user_pages_fast() comment
mm: Fix warning in insert_pfn()
memory-hotplug.rst: add some details about locking internals
powerpc/powernv: hold device_hotplug_lock when calling memtrace_offline_pages()
powerpc/powernv: hold device_hotplug_lock when calling device_online()
mm/memory_hotplug: fix online/offline_pages called w.o. mem_hotplug_lock
mm/memory_hotplug: make add_memory() take the device_hotplug_lock
mm/memory_hotplug: make remove_memory() take the device_hotplug_lock
mm/memblock.c: warn if zero alignment was requested
memblock: stop using implicit alignment to SMP_CACHE_BYTES
docs/boot-time-mm: remove bootmem documentation
mm: remove include/linux/bootmem.h
memblock: replace BOOTMEM_ALLOC_* with MEMBLOCK variants
mm: remove nobootmem
memblock: rename __free_pages_bootmem to memblock_free_pages
memblock: rename free_all_bootmem to memblock_free_all
memblock: replace free_bootmem_late with memblock_free_late
memblock: replace free_bootmem{_node} with memblock_free
mm: nobootmem: remove bootmem allocation APIs
memblock: replace alloc_bootmem with memblock_alloc
...
Let's document the magic a bit, especially why device_hotplug_lock is
required when adding/removing memory and how it all play together with
requests to online/offline memory from user space.
Link: http://lkml.kernel.org/r/20180925091457.28651-7-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The example contains two values for the capacity currently, 446 in text
and 578 in code. The numbers are all correct but can confuse some of the
readers. This patch tries to explain how the numbers are calculated to
avoid same confusion going forward.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
already supported COPY, by copying a limited amount of data and then
returning a short result, letting the client resend. The asynchronous
protocol should offer better performance at the expense of some
complexity.
The other highlight is Trond's work to convert the duplicate reply cache
to a red-black tree, and to move it and some other server caches to RCU.
(Previously these have meant taking global spinlocks on every RPC.)
Otherwise, some RDMA work and miscellaneous bugfixes.
-----BEGIN PGP SIGNATURE-----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=TTo0
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.20' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Olga added support for the NFSv4.2 asynchronous copy protocol. We
already supported COPY, by copying a limited amount of data and then
returning a short result, letting the client resend. The asynchronous
protocol should offer better performance at the expense of some
complexity.
The other highlight is Trond's work to convert the duplicate reply
cache to a red-black tree, and to move it and some other server caches
to RCU. (Previously these have meant taking global spinlocks on every
RPC)
Otherwise, some RDMA work and miscellaneous bugfixes"
* tag 'nfsd-4.20' of git://linux-nfs.org/~bfields/linux: (30 commits)
lockd: fix access beyond unterminated strings in prints
nfsd: Fix an Oops in free_session()
nfsd: correctly decrement odstate refcount in error path
svcrdma: Increase the default connection credit limit
svcrdma: Remove try_module_get from backchannel
svcrdma: Remove ->release_rqst call in bc reply handler
svcrdma: Reduce max_send_sges
nfsd: fix fall-through annotations
knfsd: Improve lookup performance in the duplicate reply cache using an rbtree
knfsd: Further simplify the cache lookup
knfsd: Simplify NFS duplicate replay cache
knfsd: Remove dead code from nfsd_cache_lookup
SUNRPC: Simplify TCP receive code
SUNRPC: Replace the cache_detail->hash_lock with a regular spinlock
SUNRPC: Remove non-RCU protected lookup
NFS: Fix up a typo in nfs_dns_ent_put
NFS: Lockless DNS lookups
knfsd: Lockless lookup of NFSv4 identities.
SUNRPC: Lockless server RPCSEC_GSS context lookup
knfsd: Allow lockless lookups of the exports
...
Back in January I posted patches to create function based events. These were
the events that you suggested I make to allow developers to easily create
events in code where no trace event exists. After posting those changes for
review, it was suggested that we implement this instead with kprobes.
The problem with kprobes is that the interface is too complex and needs to
be simplified. Masami Hiramatsu posted patches in March and I've been
playing with them a bit. There's been a bit of clean up in the kprobe code
that was inspired by the function based event patches, and a couple of
enhancements to the kprobe event interface.
- If the arch supports it (we added support for x86), you can place a
kprobe event at the start of a function and use $arg1, $arg2, etc
to reference the arguments of a function. (Before you needed to know
what register or where on the stack the argument was).
- The second is a way to see array of events. For example, if you reference
a mac address, you can add:
echo 'p:mac ip_rcv perm_addr=+574($arg2):x8[6]' > kprobe_events
And this will produce:
mac: (ip_rcv+0x0/0x140) perm_addr={0x52,0x54,0x0,0xc0,0x76,0xec}
Other changes include
- Exporting trace_dump_stack to modules
- Have the stack tracer trace the entire stack (stop trying to remove
tracing itself, as we keep removing too much).
- Added support for SDT in uprobes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW9hdjxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmtbAP9GS/o2WSvsYLSIw4+mF94eCL06lUxp
rRrktkEofm/PagEAl2JNmvHrAJN+LIrajqXTbwlZ7Ckk1rZhCW41Am7qnQs=
=sTUM
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The biggest change here is the updates to kprobes
Back in January I posted patches to create function based events.
These were the events that you suggested I make to allow developers to
easily create events in code where no trace event exists. After
posting those changes for review, it was suggested that we implement
this instead with kprobes.
The problem with kprobes is that the interface is too complex and
needs to be simplified. Masami Hiramatsu posted patches in March and
I've been playing with them a bit. There's been a bit of clean up in
the kprobe code that was inspired by the function based event patches,
and a couple of enhancements to the kprobe event interface.
- If the arch supports it (we added support for x86), you can place a
kprobe event at the start of a function and use $arg1, $arg2, etc
to reference the arguments of a function. (Before you needed to
know what register or where on the stack the argument was).
- The second is a way to see array of events. For example, if you
reference a mac address, you can add:
echo 'p:mac ip_rcv perm_addr=+574($arg2):x8[6]' > kprobe_events
And this will produce:
mac: (ip_rcv+0x0/0x140) perm_addr={0x52,0x54,0x0,0xc0,0x76,0xec}
Other changes include
- Exporting trace_dump_stack to modules
- Have the stack tracer trace the entire stack (stop trying to remove
tracing itself, as we keep removing too much).
- Added support for SDT in uprobes"
[ SDT - "Statically Defined Tracing" are userspace markers for tracing.
Let's not use random TLA's in explanations unless they are fairly
well-established as generic (at least for kernel people) - Linus ]
* tag 'trace-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (24 commits)
tracing: Have stack tracer trace full stack
tracing: Export trace_dump_stack to modules
tracing: probeevent: Fix uninitialized used of offset in parse args
tracing/kprobes: Allow kprobe-events to record module symbol
tracing/kprobes: Check the probe on unloaded module correctly
tracing/uprobes: Fix to return -EFAULT if copy_from_user failed
tracing: probeevent: Add $argN for accessing function args
x86: ptrace: Add function argument access API
tracing: probeevent: Add array type support
tracing: probeevent: Add symbol type
tracing: probeevent: Unify fetch_insn processing common part
tracing: probeevent: Append traceprobe_ for exported function
tracing: probeevent: Return consumed bytes of dynamic area
tracing: probeevent: Unify fetch type tables
tracing: probeevent: Introduce new argument fetching code
tracing: probeevent: Remove NOKPROBE_SYMBOL from print functions
tracing: probeevent: Cleanup argument field definition
tracing: probeevent: Cleanup print argument functions
trace_uprobe: support reference counter in fd-based uprobe
perf probe: Support SDT markers having reference counter (semaphore)
...
This patch documents the tcp_fwmark_accept sysctl that was
added in 3.15.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This contains a series of patches that reworks the memory carveout
handling in remoteproc, in order to allow this to be reused for
statically allocated memory regions to be used for e.g. firmware.
It adds support for audio DSP (both TZ-assisted and non-TZ assisted) and
compute DSP on Qualcomm SDM845, TZ-assisted audio DSP, compute DSP and
WiFi processor on Qualcomm QCS404 and through some renaming of the
drivers cleans up the naming situation.
Finally support for custom coreudmp segment handlers is added and
is used in the Qualcomm modem remoteproc driver to gather memory dumps
of the firmware.
-----BEGIN PGP SIGNATURE-----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=mM8w
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.20' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains a series of patches that reworks the memory carveout
handling in remoteproc, in order to allow this to be reused for
statically allocated memory regions to be used for e.g. firmware.
It adds support for audio DSP (both TZ-assisted and non-TZ assisted)
and compute DSP on Qualcomm SDM845, TZ-assisted audio DSP, compute DSP
and WiFi processor on Qualcomm QCS404 and through some renaming of the
drivers cleans up the naming situation.
Finally support for custom coreudmp segment handlers is added and is
used in the Qualcomm modem remoteproc driver to gather memory dumps of
the firmware"
* tag 'rproc-v4.20' of git://github.com/andersson/remoteproc: (36 commits)
remoteproc: qcom: q6v5-mss: Register segments/dumpfn for coredump
remoteproc: qcom: q6v5-mss: Add custom dump function for modem
remoteproc: qcom: q6v5-mss: Refactor mba load/unload sequence
remoteproc: Add mechanism for custom dump function assignment
remoteproc: Introduce custom dump function for each remoteproc segment
remoteproc: modify vring allocation to rely on centralized carveout allocator
remoteproc: qcom: q6v5: shore up resource probe handling
remoteproc: qcom: qcom_q6v5_adsp: Fix some return value check
remoteproc: modify rproc_handle_carveout to support pre-registered region
remoteproc: add helper function to check carveout device address
remoteproc: add helper function to allocate rproc_mem_entry from reserved memory
remoteproc: add alloc ops in rproc_mem_entry struct
remoteproc: introduce rproc_find_carveout_by_name function
remoteproc: introduce rproc_add_carveout function
remoteproc: add helper function to allocate and init rproc_mem_entry struct
remoteproc: add name in rproc_mem_entry struct
remoteproc: add release ops in rproc_mem_entry struct
remoteproc: add rproc_va_to_pa function
remoteproc: configure IOMMU only if device address requested
remoteproc: qcom: q6v5-mss: add SCM probe dependency
...
Plumb in a remap flag that enables the filesystem remap handler to
shorten remapping requests for callers that can handle it. Now
copy_file_range can report partial success (in case we run up against
alignment problems, resource limits, etc.).
We also enable CAN_SHORTEN for fideduperange to maintain existing
userspace-visible behavior where xfs/btrfs shorten the dedupe range to
avoid stale post-eof data exposure.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Change the remap_file_range functions to take a number of bytes to
operate upon and return the number of bytes they operated on. This is a
requirement for allowing fs implementations to return short clone/dedupe
results to the user, which will enable us to obey resource limits in a
graceful manner.
A subsequent patch will enable copy_file_range to signal to the
->clone_file_range implementation that it can handle a short length,
which will be returned in the function's return value. For now the
short return is not implemented anywhere so the behavior won't change --
either copy_file_range manages to clone the entire range or it tries an
alternative.
Neither clone ioctl can take advantage of this, alas.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Combine the clone_file_range and dedupe_file_range operations into a
single remap_file_range file operation dispatch since they're
fundamentally the same operation. The differences between the two can
be made in the prep functions.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the platform, and
several other people (Claudiu Beznea, Cristian Birsan, Eugen Hristev,
Codrin Ciubotariu) take over individual device drivers.
Thanks everyone for working on this, and welcome to the new maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7+46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Pull i2c updates from Wolfram Sang:
"I2C has not so much stuff this time. Mostly driver enablement for new
SoCs, some driver bugfixes, and some cleanups"
* 'i2c/for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (35 commits)
MAINTAINERS: add maintainer for Renesas RIIC driver
i2c: sh_mobile: Remove dummy runtime PM callbacks
i2c: uniphier-f: fix race condition when IRQ is cleared
i2c: uniphier-f: fix occasional timeout error
i2c: uniphier-f: make driver robust against concurrency
i2c: i2c-qcom-geni: Simplify irq handler
i2c: i2c-qcom-geni: Simplify tx/rx functions
i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers
i2c: mux: mlxcpld: simplify code to reach the adapter
i2c: mux: ltc4306: simplify code to reach the adapter
i2c: mux: pca954x: simplify code to reach the adapter
i2c: core: remove level of indentation in i2c_transfer
i2c: core: remove outdated DEBUG output
i2c: zx2967: use core to detect 'no zero length' quirk
i2c: tegra: use core to detect 'no zero length' quirk
i2c: qup: use core to detect 'no zero length' quirk
i2c: omap: use core to detect 'no zero length' quirk
i2c: Convert to using %pOFn instead of device_node.name
i2c: brcmstb: Allow enabling the driver on DSL SoCs
eeprom: at24: fix unexpected timeout under high load
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb12wyAAoJEAhfPr2O5OEVQG4P/3QlXjec6qlhbo6UPs54E2sC
bVdZfp3mobo8NmLRt791Yh9cc0rN45Tlf2BT8XEmCyI6+NB++obU/j0LW5XT7sp7
oE8IgeRraVFWH/Xl9lTgP15Cs6v43eyvP12xgRWBmr+TYugLHDVTheGBvU/COb3d
yaykUULezuOMLA3HsPbz5EJOmU5rZ/Wa1w1sAiNJY/cRohfVb3kO4593enwUTMSx
yHJ+AVjl/Dn3RV4yLwoybpxPH6XIb3KoLg/6Fx8bOlKy1sg0mcWpzQ1CvMUNpXTF
kdwTw3ri1bfYnjChZewuKoJU8Wcw0Gt7pkqAhULN1ieo84MNA3bNor56pdRPaOZW
KxzlXZRS6xgYW8bzZ51N0Ku6fwSt3AWRE7TeKcrHF84Yb8vOtPS15sp3qc+9o9rb
EDV/lJLcz4bbi3W28di5WMFaN7LHxCHnRV7GvrcNQm6Im62CBFZHiI7jKjMv3tXp
Taes0utMPGfWuY6fv4LmuBzFG4nGB6/H4RiVvL1cLkjnx/FJtWGH+1uOcKDraKeI
ENBrK0VYrNH7nCDGNehiamStcVK+27tS+xsuqoZkGz6RA8vAxYBXTIZULXA98BPA
f6NC32ZNJaruxh4qh5tUy+LKPGzXs0sWa9kfgKmFfaOndFLMjGTXHpAT5AYJMbNe
iqKi/4aXD4aKAWTA7PPg
=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
Clean up the cache code by removing the non-RCU protected lookup.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Here is the big tty and serial pull request for 4.20-rc1
Lots of little things here, including a merge from the SPI tree in order
to keep things simpler for everyone to sync around for one platform.
Major stuff is:
- tty buffer clearing after use
- atmel_serial fixes and additions
- xilinx uart driver updates
and of course, lots of tiny fixes and additions to individual serial
drivers.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bW0w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymYhgCfbxr0T+4lF/rpGxNXNnV4u5boRJUAn2L8R+1y
URbAWHvKfaby2AVfQ1z0
=qTHH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty and serial pull request for 4.20-rc1
Lots of little things here, including a merge from the SPI tree in
order to keep things simpler for everyone to sync around for one
platform.
Major stuff is:
- tty buffer clearing after use
- atmel_serial fixes and additions
- xilinx uart driver updates
and of course, lots of tiny fixes and additions to individual serial
drivers.
All of these have been in linux-next with no reported issues for a
while"
* tag 'tty-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
of: base: Change logic in of_alias_get_alias_list()
of: base: Fix english spelling in of_alias_get_alias_list()
serial: sh-sci: do not warn if DMA transfers are not supported
serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES
tty: check name length in tty_find_polling_driver()
serial: sh-sci: Add r8a77990 support
tty: wipe buffer if not echoing data
tty: wipe buffer.
serial: fsl_lpuart: Remove the alias node dependence
TTY: sn_console: Replace spin_is_locked() with spin_trylock()
Revert "serial:serial_core: Allow use of CTS for PPS line discipline"
serial: 8250_uniphier: add auto-flow-control support
serial: 8250_uniphier: flatten probe function
serial: 8250_uniphier: remove unused "fifo-size" property
dt-bindings: serial: sh-sci: Document r8a7744 bindings
serial: uartps: Fix missing unlock on error in cdns_get_id()
tty/serial: atmel: add ISO7816 support
tty/serial_core: add ISO7816 infrastructure
serial:serial_core: Allow use of CTS for PPS line discipline
serial: docs: Fix filename for serial reference implementation
...
Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument device
support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a bit
"late" due to them getting stuck on my laptop during travel to the
Mantainers summit.
When merging with your tree, there will be 2 merge conflicts, both files
will be simple to resolve, just delete them :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bSGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk5eACfYp73m9tLO22rnBcXJ73bWAYSTOMAn2GEL4Nc
LZBXs8QvvJIwfqmi7ofn
=UWJn
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
- Enable ti-msgmr driver for the K3 platform as well
- Add QCS404 to compatible list of QCOM's APCS IPC driver
- Minor spelling fixes toogle -> toggle
- kzalloc failure catch in Mediatek driver
-----BEGIN PGP SIGNATURE-----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=KH5m
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v4.20' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- convert print users to use the %pOFn format specifier
- enable ti-msgmr driver for the K3 platform as well
- add QCS404 to compatible list of QCOM's APCS IPC driver
- minor spelling fixes toogle -> toggle
- kzalloc failure catch in Mediatek driver
* tag 'mailbox-v4.20' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mediatek: Add check for possible failure of kzalloc
mailbox: bcm-flexrm-mailbox: fix spelling mistake "toogle" -> "toggle"
mailbox: qcom: Add QCS404 APPS Global compatible
drivers: mailbox: Make ti-msgmr driver depend on ARCH_K3
mailbox: Convert to using %pOFn instead of device_node.name
As far as I can tell the bindings that were added in commit
9c04400f7e ("dt-bindings: drm/panel: Document Innolux TV123WAM panel
bindings") weren't actually for Innolux TV123WAM but were actually for
Innolux P120ZDG-BF1.
As far as I can tell the Innolux TV123WAM isn't a real panel and but
it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1.
Let's unmosh.
Here's my evidence:
* Searching for TV123WAM on the Internet turns up a TI panel. While
it's possible that an Innolux panel has the same model number as the
TI Panel, it seems a little doubtful. Looking up the datasheet from
the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm.
* As far as I know, the patch adding the Innolux Panel was supposed to
be for the board that's sitting in front of me as I type this
(support for that board is not yet upstream). On the back of that
panel I see Innolux P120ZDZ-EZ1 rev B1.
* Someone pointed me at a datasheet that's supposed to be for the
panel in front of me (sorry, I can't share the datasheet). That
datasheet has the string "p120zdg-bf1"
* If I search for "P120ZDG-BF1" on the Internet I get hits for panels
that are 2160x1440. They don't have datasheets, but the fact that
the resolution matches is a good sign.
While we doing the rename, also mention that no-hpd can be used with
this panel. See the previous patch in this series ("drm/panel:
simple: Add "no-hpd" delay for Innolux TV123WAM").
Fixes: 9c04400f7e ("dt-bindings: drm/panel: Document Innolux TV123WAM panel bindings")
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-5-dianders@chromium.org
Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.
However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up. In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.
Let's add a property in the device tree for this concept.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-1-dianders@chromium.org
Release, which has been through 10 rounds of review on mailing list.
We almost got the Acked-by/Reviewed-by of all patches except "Process
management and Signal", but all've been tested.
Here is the LTP-20180118 test report:
-----------------------------------------------
Total Tests: 1298
Total Skipped Tests: 281
Total Failures: 10
Kernel Version: 4.19.0+
Machine Architecture: csky
Hostname: buildroot
-----------------------------------------------
This patchset adds architecture support to Linux for C-SKY's 32-bit embedded
There are two ABI versions with several CPU cores in this patchset:
ABIv1: 610 (16-bit instruction, 32-bit data path, VIPT Cache ...)
ABIv2: 807 810 860 (16/32-bit variable length instruction, PIPT Cache,
SMP ...)
More information: http://en.c-sky.com
The development repo: https://github.com/c-sky/csky-linux
ABI Documentation: https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..."
will be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future.
Changes in v10:
- Remove duplicated headers in asm/Kbuild and uapi/asm/Kbuild.
- Change to (__NR_arch_specific_syscall + 1) in unistd.h.
- Drop dword access for get_user_size patch.
- Involve the interrupt controller drivers after got Reviewed-by.
Changes in v9:
- Remove unused code in smp.c and use per_cpu for ipi_data.
- Fixup r15 register access in abiv1/alignment.c.
- Improve the changelog comment in commit-msg.
Changes in v8:
- Pass make allmodconfig.
- Implement abiv1 get_user_dword().
- Remove set_irq_mapping() used by driver in smp.c.
Changes in v7:
- Use checkpatch.pl to check all patches and fixup as possible.
- Remove github.com/c-sky print in bootup.
- Give a return in DMA_ATTR_NON_CONSISTENT in csky_dma_alloc_atomic().
- Remove the NSIGXXX in fpu.c and use force_sig_fault() in fpu.c.
- Remove irq.h and add it in asm/Kbuild.
- Use byteswap helpers in abiv1/bswapXi.c.
- Fixup arch_sync_dma() only with one page problem.
Changes in v6:
- use asm-generic/bitops/atomic.h for all in asm/bitops.h
- fix flush_cache_range and tlb_start_vma
- fix compile error with include linux/bug.h in cmpxchg.h
- improve the comment
Changes in v5:
- remove redundant smp_mb operations in spinlock.h
- add commit message for dt-bindings docs
- add CPUHP_AP_CSKY_TIMER_STARTING in hotplug.h for csky_mptimer
- add COMPILE_TEST for timer-gx6605s Kconfig
- seperate csky two interrupt controllers with 2 patches
- add MAINTAINERS patch for csky
- move IPI_IRQ into csky_mptimer, fixup irq_mapping problem
- coding convension
Changes in v4:
- cleanup defconfig
- use ksys_ in syscall.c
- remove wrong comment in vdso.c
- Use GENERIC_IRQ_MULTI_HANDLER
- optimize the memset.c
- fixup dts warnings
- remove big-endian in byteorder.h
Changes in v3:
dc560f1 csky: change to EM_CSKY 252 for elf.h
2ac3ddf csky: remove gx6605s.dts
af00b8c csky: add defconfig and qemu.dts
6c87efb csky: remove the deprecate name.
f6dda39 csky: add dt-bindings doc.
d9f02a8 csky: remove KERNEL_VERSION in upstream branch
7bd663c csky: Use kernel/dma/noncoherent.c
1544c09 csky: bugfix emmc hang up LINS-976
e963271 csky: cleanup include/asm/Kbuild
cd267ba csky: remove CSKY_DEBUG_INFO
78950da csky: remove dcache invalid.
13fe51d csky: remove csum_ipv6_magic(), use generic one.
a7372db csky: bugfix CK810 access twice error.
1bb7c69 csky: bugfix add gcc asm memory for barrier.
5ea3257 csky: add -msoft-float instead of -mfloat-abi=soft.
38b037d csky: bugfix losing cache flush range.
ab5e8c4 csky: Add ticket-spinlock and qrwlock support.
c9aaec5 csky: rename cskyksyms.c to libgcc_ksyms.c
28c5e48 csky: avoid the MB on failure: trylock
f929c97 csky: bugfix idly4 may cause exception.
09dc496 csky: Use GENERIC_ASHLDI3/ASHRDI3 etc
6ecc99d csky: optimize smp boot code.
16f50df csky: asm/bug.h simple implement.
0ba532a csky: csky asm/atomic.h added.
df66947 csky: asm/compat.h added
275a06f csky: String operations optimization
4c021dd csky: ck860 SMP memory barrier optimize
fc39c66 csky: Add wait/doze/stop
d005144 csky: add GENERIC_ALLOCATOR
4a10074 csky: bugfix cma failed for highmem.
9f2ca70 csky: CMA supported :)
53791f4 csky: optimize csky_dma_alloc_nonatomic
974676e csky: optimize the cpuinfo printf.
2538669 csky: bugfix make headers_install error.
1158d0c csky: prevent hard-float and vdsp instructions.
dc3c856 csky: increase Normal Memory to 1GB
6ee5932 csky: bugfix qemu mmu couldn't support 0xffffe000
1d7dfb8 csky: csky_dma_alloc_atomic added.
caf6610 csky: restruct the fixmap memory layout.
5a17eaa csky: use -Wa,-mcpu=ckxxxfv to the as.
4d51829 csky: use Kconfig.hz.
f3f88fa csky: BUGFIX add -mcpu=ck860f support
6192fd1 csky: support ck860 fpu.
7aa5e01 csky: BUGFIX add smp_mb before ldex.
15758e2 csky: BUGFIX tlbi couldn't handle ASID in another CPU core.
d69640d csky: enable tlbi.vas to flush one tlb entry
Changes in v2:
a29bfc8 csky: add pre_mmu_init, move misc mmu setup to mm/init.c
4eab702 csky: no need kmap for !VM_EXEC.
6770eec csky: Use TEE as the name of CPU Trusted Execution Enviornment.
a56c8c7 csky: update the cache flush api.
1a48a95 csky: add C-SKY Trust Zone.
b7a0a44 csky: use CONFIG_RAM_BASE as the same in memory of dts.
15adf81 csky: remove unused code.
35c0d97 csky: bugfix lost a cacheline flush when start isn't cacheline-aligned.
4e82c8d csky: use tlbi.alls for ck860 smp temporary.
ae7149e csky: bugfix use kmap_atomic() to prevent no mapped addr.
5538795 csky: bugfix user access in kernel space.
a7aa591 csky: add 16bit user space bkpt.
0de70ec csky: add sync.is for cmpxchg in SMP.
c5c08a1 csky: seperate sync.is and sync for SMP and Non-SMP.
dbbf4dc csky: use sync.is for ck860 mb().
f33f8da csky: rewrite the alignment implement.
68152c7 csky: bugfix alignment pt_regs error.
d618d43 csky: support set_affinity for irq balance in SMP
ebf86c9 csky: bugfix compile error without CONFIG_SMP.
8537eea csky: remove debug code.
4ebc051 csky: bugfix compile error with linux-4.9.56
75a938e csky: C-SKY SMP supported.
0eebc07 csky: use internal function for map_sg.
3d29751 csky: bugfix can't support highmem
b545d2a csky: bugfix r26 is the link reg for jsri_to_jsr.
9e3313a csky: bugfix sync tls for abiv1 in ptrace.
587a0d2 csky: use __NR_rt_sigreturn in asm-generic.
f562b46 csky: bugfix gpr_set & fpr_set
f57266f csky: bugfix fpu_fpe_helper excute mtcr mfcr.
c676669 csky: bugfix ave is default enable on reset.
d40d34d csky: remove unused sc_mask in sigcontext.h.
274b7a2 csky: redesign the signal's api
7501771 csky: bugfix forget restore usp.
923e2ca csky: re-struct the pt_regs for regset.
2a1e499 csky: fixup config.
ada81ec csky: bugfix abiv1 compile error.
e34acb9 csky: bugfix abiv1 couldn't support -mno-stack-size.
ec53560 csky: change irq map, reserve soft_irq&private_irq space.
c7576f7 csky: bugfix modpost warning with -mno-stack-size
c8ff9d4 csky: support csky mp timer alpha version.
deabaaf csky: update .gitignore.
574815c csky: bugfix compile error with abiv1 in 4.15
0b426a7 csky: bugfix format of cpu verion id.
083435f csky: irq-csky-v2 alpha init.
21209e5 csky: add .gitignore
73e19b4 csky: remove FMFS_FPU_REGS/FMTS_FPU_REGS
07e8fac csky: add fpu regset in ptrace.c
cac779d csky: add CSKY_VECIRQ_LEGENCY for SOC bug.
54bab1d csky: move usp into pt_regs.
b167422 csky: support regset for ptrace.
a098d4c csky: remove ARCH_WANT_IPC_PARSE_VERSION
fe61a84 csky: add timer-of support.
27702e2 csky: bugfix boot error.
ebe3edb csky: bugfix gx6605s boot failed - add __HEAD to head.section for head.S - move INIT_SECTION together to fix compile warning.
7138cae csky: coding convension for timer-nationalchip.c
fa7f9bb csky: use ffs instead of fls.
ddc9e81 csky: change to generic irq chip for irq-csky.c
e9be8b9 irqchip: add generic irq chip for irq-nationalchip
2ee83fe csky: add set_handle_irq(), ref from openrisc & arm.
74181d6 csky: use irq_domain_add_linear instead of leagcy.
fa45ae4 csky: bugfix setup stroge order for uncached.
eb8030f csky: add HIGHMEM config in Kconfig
4f983d4 csky: remove "default n" in Kconfig
2467575 csky: use asm-generic/signal.h
77438e5 csky: coding conventions for irq.c
2e4a2b4 csky: optimize the cache flush ops.
96e1c58 csky: add CONFIG_CPU_ASID_BITS.
9339666 csky: add cprcr() cpwcr() for abiv1
ff05be4 csky: add THREAD_SHIFT define in asm/page.h
52ab022 csky: add mfcr() mtcr() in asm/reg_ops.h
bdcd8f3 csky: revert back Kconfig select.
590c7e6 csky: bugfix compile error with CONFIG_AUDIT
1989292 csky: revert some back with cleanup unistd.h
f1454fe csky: cleanup unistd.h
5d2985f csky: cleanup Kconfig and Makefile.
423d97e csky: cancel subdirectories
cae2af4 csky: use asm-generic/fcntl.h
-----BEGIN PGP SIGNATURE-----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=kHer
-----END PGP SIGNATURE-----
Merge tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux
Pull C-SKY architecture port from Guo Ren:
"This contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list.
More information:
http://en.c-sky.com
The development repo:
https://github.com/c-sky/csky-linux
ABI Documentation:
https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will
be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future"
Arnd acks, and adds the following notes:
"I did a thorough review of the ABI, which as usual mainly consists of
spotting any files that don't use the asm-generic ABI itself, and
having it changed to it matches exactly what we do on other new
architectures.
I also looked at every other patch and commented on maybe half of them
where I saw something that did not quite seem right. Others have
reviewed specific patches in greater depth. I'm sure that one could
fine more of the minor details, but as long as they are not ABI
relevant, they can be fixed later.
The only patch that is part of the ABI and that nobody reviewed is the
signal handling. This is one of the areas I never worked on in much
detail. I did not see anything wrong with it, but I also don't know
what the problems with the other architectures are here, and we seem
to be hitting issues occasionally, and we never managed to generalize
this enough for new architectures to have a trivial implementation.
I was originally hoping that we could have the 64-bit time_t
interfaces ready in time to completely drop the 32-bit ones, but that
did not happen. We might still remove them in the next merge window
depending on whether the libc upstream people prefer to keep them or
not.
One more general comment: I think this may well be the last new CPU
architecture we ever add to the kernel. Both nds32 and c-sky are made
by companies that also work on risc-v, and generally speaking risc-v
seems to be killing off any of the minor licensable instruction set
projects, just like ARM has mostly killed off the custom
vendor-specific instruction sets already.
If we add another architecture in the future, it may instead be
something like the LLVM bitcode or WebAssembly, who knows?"
To which Geert Uytterhoeven pipes in about another architecture still in
the pipeline: Kalray MPPA.
* tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux: (24 commits)
dt-bindings: interrupt-controller: C-SKY APB intc
irqchip: add C-SKY APB bus interrupt controller
dt-bindings: interrupt-controller: C-SKY SMP intc
irqchip: add C-SKY SMP interrupt controller
MAINTAINERS: Add csky
dt-bindings: Add vendor prefix for csky
dt-bindings: csky CPU Bindings
csky: Misc headers
csky: SMP support
csky: Debug and Ptrace GDB
csky: User access
csky: Library functions
csky: ELF and module probe
csky: Atomic operations
csky: IRQ handling
csky: VDSO and rt_sigreturn
csky: Process management and Signal
csky: MMU and page table management
csky: Cache and TLB routines
csky: System Call
...
Pull networking fixes from David Miller:
1) GRO overflow entries are not unlinked properly, resulting in list
poison pointers being dereferenced.
2) Fix bridge build with ipv6 disabled, from Nikolay Aleksandrov.
3) Direct packet access and other fixes in BPF from Daniel Borkmann.
4) gred_change_table_def() gets passed the wrong pointer, a pointer to
a set of unparsed attributes instead of the attribute itself. From
Jakub Kicinski.
5) Allow macsec device to be brought up even if it's lowerdev is down,
from Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: diag: document swapped src/dst in udp_dump_one.
macsec: let the administrator set UP state even if lowerdev is down
macsec: update operstate when lower device changes
net: sched: gred: pass the right attribute to gred_change_table_def()
ptp: drop redundant kasprintf() to create worker name
net: bridge: remove ipv6 zero address check in mcast queries
net: Properly unlink GRO packets on overflow.
bpf: fix wrong helper enablement in cgroup local storage
bpf: add bpf_jit_limit knob to restrict unpriv allocations
bpf: make direct packet write unclone more robust
bpf: fix leaking uninitialized memory on pop/peek helpers
bpf: fix direct packet write into pop/peek helpers
bpf: fix cg_skb types to hint access type in may_access_direct_pkt_data
bpf: fix direct packet access for flow dissector progs
bpf: disallow direct packet access for unpriv in cg_skb
bpf: fix test suite to enable all unpriv program types
bpf, btf: fix a missing check bug in btf_parse
selftests/bpf: add config fragments BPF_STREAM_PARSER and XDP_SOCKETS
bpf: devmap: fix wrong interface selection in notifier_call
-----BEGIN PGP SIGNATURE-----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=3yxi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlvURsoACgkQ+iyteGJfRspw9gCgtLHtFIm++UnS48IhP+ZlioGI
KqYAoLMhbd9IzpgPd1F8cLT/N29zAUcU
=bvZ1
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-4.20-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Armada 37xx CPU watchdog
- w83627hf_wdt: Add Support for NCT6796D, NCT6797D, NCT6798D
- hpwdt: several improvements
- renesas_wdt: SPDX identifiers, stop when unregistering, support for
R7S9210
- rza_wdt: SPDX identifiers, support longer timeouts
- core: fix null pointer dereference when releasing cdev
- iTCO_wdt: Drop option vendorsupport=2
- sama5d4: fix timeout-sec usage
- lantiq_wdt: convert to watchdog framework
- several small fixes
* tag 'linux-watchdog-4.20-rc1' of git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: ts4800: release syscon device node in ts4800_wdt_probe()
watchdog: armada_37xx_wdt: use do_div for u64 division
documentation: watchdog: add documentation for armada-37xx-wdt
dt-bindings: watchdog: Document armada-37xx-wdt binding
watchdog: Add support for Armada 37xx CPU watchdog
dt-bindings: watchdog: add mpc8xxx-wdt support
watchdog: mpc8xxx: provide boot status
MAINTAINERS: Fix file pattern for MEN Z069 watchdog driver
dt-bindings: watchdog: renesas-wdt: Add support for R7S9210
watchdog: rza_wdt: Support longer timeouts
watchdog: hpwdt: Disable PreTimeout when Timeout is smaller
watchdog: w83627hf_wdt: Support NCT6796D, NCT6797D, NCT6798D
watchdog: mpc8xxx: use dev_xxxx() instead of pr_xxxx()
watchdog: lantiq: add get_timeleft callback
watchdog: lantiq: Convert to watchdog_device
watchdog: lantiq: update register names to better match spec
watchdog: sama5d4: fix timeout-sec usage
watchdog: fix a small number of "watchog" typos in comments
watchdog: rza_wdt: convert to SPDX identifiers
watchdog: iTCO_wdt: Remove unused hooks
...
Daniel Borkmann says:
====================
pull-request: bpf 2018-10-27
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix toctou race in BTF header validation, from Martin and Wenwen.
2) Fix devmap interface comparison in notifier call which was
neglecting netns, from Taehee.
3) Several fixes in various places, for example, correcting direct
packet access and helper function availability, from Daniel.
4) Fix BPF kselftest config fragment to include af_xdp and sockmap,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (132 commits)
hugetlbfs: dirty pages as they are added to pagecache
mm: export add_swap_extent()
mm: split SWP_FILE into SWP_ACTIVATED and SWP_FS
tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE
mm: thp: relocate flush_cache_range() in migrate_misplaced_transhuge_page()
mm: thp: fix mmu_notifier in migrate_misplaced_transhuge_page()
mm: thp: fix MADV_DONTNEED vs migrate_misplaced_transhuge_page race condition
mm/kasan/quarantine.c: make quarantine_lock a raw_spinlock_t
mm/gup: cache dev_pagemap while pinning pages
Revert "x86/e820: put !E820_TYPE_RAM regions into memblock.reserved"
mm: return zero_resv_unavail optimization
mm: zero remaining unavailable struct pages
tools/testing/selftests/vm/gup_benchmark.c: add MAP_HUGETLB option
tools/testing/selftests/vm/gup_benchmark.c: add MAP_SHARED option
tools/testing/selftests/vm/gup_benchmark.c: allow user specified file
tools/testing/selftests/vm/gup_benchmark.c: fix 'write' flag usage
mm/gup_benchmark.c: add additional pinning methods
mm/gup_benchmark.c: time put_page()
mm: don't raise MEMCG_OOM event due to failed high-order allocation
mm/page-writeback.c: fix range_cyclic writeback vs writepages deadlock
...
It was reported that on some of our machines containers were restarted
with OOM symptoms without an obvious reason. Despite there were almost no
memory pressure and plenty of page cache, MEMCG_OOM event was raised
occasionally, causing the container management software to think, that OOM
has happened. However, no tasks have been killed.
The following investigation showed that the problem is caused by a failing
attempt to charge a high-order page. In such case, the OOM killer is
never invoked. As shown below, it can happen under conditions, which are
very far from a real OOM: e.g. there is plenty of clean page cache and no
memory pressure.
There is no sense in raising an OOM event in this case, as it might
confuse a user and lead to wrong and excessive actions (e.g. restart the
workload, as in my case).
Let's look at the charging path in try_charge(). If the memory usage is
about memory.max, which is absolutely natural for most memory cgroups, we
try to reclaim some pages. Even if we were able to reclaim enough memory
for the allocation, the following check can fail due to a race with
another concurrent allocation:
if (mem_cgroup_margin(mem_over_limit) >= nr_pages)
goto retry;
For regular pages the following condition will save us from triggering
the OOM:
if (nr_reclaimed && nr_pages <= (1 << PAGE_ALLOC_COSTLY_ORDER))
goto retry;
But for high-order allocation this condition will intentionally fail. The
reason behind is that we'll likely fall to regular pages anyway, so it's
ok and even preferred to return ENOMEM.
In this case the idea of raising MEMCG_OOM looks dubious.
Fix this by moving MEMCG_OOM raising to mem_cgroup_oom() after allocation
order check, so that the event won't be raised for high order allocations.
This change doesn't affect regular pages allocation and charging.
Link: http://lkml.kernel.org/r/20181004214050.7417-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Address issues slowing persistent memory initialization", v5.
The main thing this patch set achieves is that it allows us to initialize
each node worth of persistent memory independently. As a result we reduce
page init time by about 2 minutes because instead of taking 30 to 40
seconds per node and going through each node one at a time, we process all
4 nodes in parallel in the case of a 12TB persistent memory setup spread
evenly over 4 nodes.
This patch (of 3):
On systems with a large amount of memory it can take a significant amount
of time to initialize all of the page structs with the PAGE_POISON_PATTERN
value. I have seen it take over 2 minutes to initialize a system with
over 12TB of RAM.
In order to work around the issue I had to disable CONFIG_DEBUG_VM and
then the boot time returned to something much more reasonable as the
arch_add_memory call completed in milliseconds versus seconds. However in
doing that I had to disable all of the other VM debugging on the system.
In order to work around a kernel that might have CONFIG_DEBUG_VM enabled
on a system that has a large amount of memory I have added a new kernel
parameter named "vm_debug" that can be set to "-" in order to disable it.
Link: http://lkml.kernel.org/r/20180925201921.3576.84239.stgit@localhost.localdomain
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system that executes multiple cgrouped jobs and independent
workloads, we don't just care about the health of the overall system, but
also that of individual jobs, so that we can ensure individual job health,
fairness between jobs, or prioritize some jobs over others.
This patch implements pressure stall tracking for cgroups. In kernels
with CONFIG_PSI=y, cgroup2 groups will have cpu.pressure, memory.pressure,
and io.pressure files that track aggregate pressure stall times for only
the tasks inside the cgroup.
Link: http://lkml.kernel.org/r/20180828172258.3185-10-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Johannes Weiner <jweiner@fb.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Enderborg <peter.enderborg@sony.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When systems are overcommitted and resources become contended, it's hard
to tell exactly the impact this has on workload productivity, or how close
the system is to lockups and OOM kills. In particular, when machines work
multiple jobs concurrently, the impact of overcommit in terms of latency
and throughput on the individual job can be enormous.
In order to maximize hardware utilization without sacrificing individual
job health or risk complete machine lockups, this patch implements a way
to quantify resource pressure in the system.
A kernel built with CONFIG_PSI=y creates files in /proc/pressure/ that
expose the percentage of time the system is stalled on CPU, memory, or IO,
respectively. Stall states are aggregate versions of the per-task delay
accounting delays:
cpu: some tasks are runnable but not executing on a CPU
memory: tasks are reclaiming, or waiting for swapin or thrashing cache
io: tasks are waiting for io completions
These percentages of walltime can be thought of as pressure percentages,
and they give a general sense of system health and productivity loss
incurred by resource overcommit. They can also indicate when the system
is approaching lockup scenarios and OOMs.
To do this, psi keeps track of the task states associated with each CPU
and samples the time they spend in stall states. Every 2 seconds, the
samples are averaged across CPUs - weighted by the CPUs' non-idle time to
eliminate artifacts from unused CPUs - and translated into percentages of
walltime. A running average of those percentages is maintained over 10s,
1m, and 5m periods (similar to the loadaverage).
[hannes@cmpxchg.org: doc fixlet, per Randy]
Link: http://lkml.kernel.org/r/20180828205625.GA14030@cmpxchg.org
[hannes@cmpxchg.org: code optimization]
Link: http://lkml.kernel.org/r/20180907175015.GA8479@cmpxchg.org
[hannes@cmpxchg.org: rename psi_clock() to psi_update_work(), per Peter]
Link: http://lkml.kernel.org/r/20180907145404.GB11088@cmpxchg.org
[hannes@cmpxchg.org: fix build]
Link: http://lkml.kernel.org/r/20180913014222.GA2370@cmpxchg.org
Link: http://lkml.kernel.org/r/20180828172258.3185-9-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Johannes Weiner <jweiner@fb.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Enderborg <peter.enderborg@sony.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vmstat NR_KERNEL_MISC_RECLAIMABLE counter is for kernel non-slab
allocations that can be reclaimed via shrinker. In /proc/meminfo, we can
show the sum of all reclaimable kernel allocations (including slab) as
"KReclaimable". Add the same counter also to per-node meminfo under /sys
With this counter, users will have more complete information about kernel
memory usage. Non-slab reclaimable pages (currently just the ION
allocator) will not be missing from /proc/meminfo, making users wonder
where part of their memory went. More precisely, they already appear in
MemAvailable, but without the new counter, it's not obvious why the value
in MemAvailable doesn't fully correspond with the sum of other counters
participating in it.
Link: http://lkml.kernel.org/r/20180731090649.16028-6-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Vijayanand Jitta <vjitta@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the slub_debug syntax to "slub_debug=<flags>[,<slub>]*", where
<slub> may contain an asterisk at the end. For example, the following
would poison all kmalloc slabs:
slub_debug=P,kmalloc*
and the following would apply the default flags to all kmalloc and all
block IO slabs:
slub_debug=,bio*,kmalloc*
Please note that a similar patch was posted by Iliyan Malchev some time
ago but was never merged:
https://marc.info/?l=linux-mm&m=131283905330474&w=2
Link: http://lkml.kernel.org/r/20180928111139.27962-1-atomlin@redhat.com
Signed-off-by: Aaron Tomlin <atomlin@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Iliyan Malchev <malchev@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of fairly
complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for each
process and preload them on context switch. Leading to a 27% speedup for our
context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print more debug
information when they occur, and try to continue running by flushing the SLB
and reloading, rather than treating them as fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on 64-bit
Book3S. We only support up to 512TB as regular system memory, otherwise the
percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are presented
to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE flags.
- Add a driver for the PAPR SCM (storage class memory) interface, allowing
guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we need to use
a trampoline to get to ftrace_caller().
Many other smaller enhancements and cleanups.
Thanks to:
Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton Blanchard, Aravinda
Prasad, Bartlomiej Zolnierkiewicz, Benjamin Herrenschmidt, Breno Leitao,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Dan Carpenter, Daniel
Axtens, Finn Thain, Gautham R. Shenoy, Gustavo Romero, Haren Myneni, Hari
Bathini, Jia Hongtao, Joel Stanley, John Allen, Laurent Dufour, Madhavan
Srinivasan, Mahesh Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael
Bringmann, Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver O'Halloran,
Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab, Rob Herring, Sam
Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan Johnson, Stephen Rothwell,
Stewart Smith, Suraj Jitindar Singh, Tyrel Datwyler, Vaibhav Jain, Vasant
Hegde, YueHaibing, zhong jiang,
-----BEGIN PGP SIGNATURE-----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=I0pj
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A large series to rewrite our SLB miss handling, replacing a lot of
fairly complicated asm with much fewer lines of C.
- Following on from that, we now maintain a cache of SLB entries for
each process and preload them on context switch. Leading to a 27%
speedup for our context switch benchmark on Power9.
- Improvements to our handling of SLB multi-hit errors. We now print
more debug information when they occur, and try to continue running
by flushing the SLB and reloading, rather than treating them as
fatal.
- Enable THP migration on 64-bit Book3S machines (eg. Power7/8/9).
- Add support for physical memory up to 2PB in the linear mapping on
64-bit Book3S. We only support up to 512TB as regular system
memory, otherwise the percpu allocator runs out of vmalloc space.
- Add stack protector support for 32 and 64-bit, with a per-task
canary.
- Add support for PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP.
- Support recognising "big cores" on Power9, where two SMT4 cores are
presented to us as a single SMT8 core.
- A large series to cleanup some of our ioremap handling and PTE
flags.
- Add a driver for the PAPR SCM (storage class memory) interface,
allowing guests to operate on SCM devices (acked by Dan).
- Changes to our ftrace code to handle very large kernels, where we
need to use a trampoline to get to ftrace_caller().
And many other smaller enhancements and cleanups.
Thanks to: Alan Modra, Alistair Popple, Aneesh Kumar K.V, Anton
Blanchard, Aravinda Prasad, Bartlomiej Zolnierkiewicz, Benjamin
Herrenschmidt, Breno Leitao, Cédric Le Goater, Christophe Leroy,
Christophe Lombard, Dan Carpenter, Daniel Axtens, Finn Thain, Gautham
R. Shenoy, Gustavo Romero, Haren Myneni, Hari Bathini, Jia Hongtao,
Joel Stanley, John Allen, Laurent Dufour, Madhavan Srinivasan, Mahesh
Salgaonkar, Mark Hairgrove, Masahiro Yamada, Michael Bringmann,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers, Oliver
O'Halloran, Paul Mackerras, Petr Vorel, Rashmica Gupta, Reza Arbab,
Rob Herring, Sam Bobroff, Samuel Mendoza-Jonas, Scott Wood, Stan
Johnson, Stephen Rothwell, Stewart Smith, Suraj Jitindar Singh, Tyrel
Datwyler, Vaibhav Jain, Vasant Hegde, YueHaibing, zhong jiang"
* tag 'powerpc-4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (221 commits)
Revert "selftests/powerpc: Fix out-of-tree build errors"
powerpc/msi: Fix compile error on mpc83xx
powerpc: Fix stack protector crashes on CPU hotplug
powerpc/traps: restore recoverability of machine_check interrupts
powerpc/64/module: REL32 relocation range check
powerpc/64s/radix: Fix radix__flush_tlb_collapsed_pmd double flushing pmd
selftests/powerpc: Add a test of wild bctr
powerpc/mm: Fix page table dump to work on Radix
powerpc/mm/radix: Display if mappings are exec or not
powerpc/mm/radix: Simplify split mapping logic
powerpc/mm/radix: Remove the retry in the split mapping logic
powerpc/mm/radix: Fix small page at boundary when splitting
powerpc/mm/radix: Fix overuse of small pages in splitting logic
powerpc/mm/radix: Fix off-by-one in split mapping logic
powerpc/ftrace: Handle large kernel configs
powerpc/mm: Fix WARN_ON with THP NUMA migration
selftests/powerpc: Fix out-of-tree build errors
powerpc/time: no steal_time when CONFIG_PPC_SPLPAR is not selected
powerpc/time: Only set CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC64
powerpc/time: isolate scaled cputime accounting in dedicated functions.
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Pull thermal SoC updates from Eduardo Valentin:
"Several new things coming up. Specifics:
- Rework of tsens and hisi thermal drivers
- OF-thermal now allows sharing multiple cooling devices on maps
- Added support for r8a7744 and R8A77970 on rcar thermal driver
- Added support for r8a774a1 on rcar_gen3 thermal driver
- New thermal driver stm32
- Fixes on multiple thermal drivers: of-thermal, imx, qoriq, armada,
qcom-spmi, rcar, da9062/61"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (41 commits)
thermal: da9062/61: Prevent hardware access during system suspend
thermal: rcar_thermal: Prevent doing work after unbind
thermal: rcar_thermal: Prevent hardware access during system suspend
thermal: rcar_gen3_thermal: add R8A77980 support
dt-bindings: thermal: rcar-gen3-thermal: document R8A77980 bindings
thermal: add stm32 thermal driver
dt-bindings: stm32-thermal: add binding documentation
thermal: rcar_thermal: add R8A77970 support
dt-bindings: thermal: rcar-thermal: document R8A77970 bindings
thermal: rcar_thermal: fix duplicate IRQ request
dt-bindings: thermal: rcar: Add device tree support for r8a7744
thermal/drivers/hisi: Add the dual clusters sensors for hi3660
thermal/drivers/hisi: Add more sensors channel
thermal/drivers/hisi: Remove pointless irq field
thermal/drivers/hisi: Use platform_get_irq_byname
thermal/drivers/hisi: Replace macro name with relevant sensor location
thermal/drivers/hisi: Add multiple sensors support
thermal/drivers/hisi: Prepare to support multiple sensors
thermal/drivers/hisi: Factor out the probe functions
thermal/drivers/hisi: Set the thermal zone private data to the sensor pointer
...
These updates bring:
- Debugfs support for the Intel VT-d driver. When enabled, it
now also exposes some of its internal data structures to
user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing
and fast-path iova allocation code. This is expected to be a
major performance improvement, as this allocation path scales
a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=q1HJ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Debugfs support for the Intel VT-d driver.
When enabled, it now also exposes some of its internal data
structures to user-space for debugging purposes.
- ARM-SMMU driver now uses the generic deferred flushing and fast-path
iova allocation code.
This is expected to be a major performance improvement, as this
allocation path scales a lot better.
- Support for r8a7744 in the Renesas iommu driver
- Couple of minor fixes and improvements all over the place
* tag 'iommu-updates-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu/arm-smmu-v3: Remove unnecessary wrapper function
iommu/arm-smmu-v3: Add SPDX header
iommu/amd: Add default branch in amd_iommu_capable()
dt-bindings: iommu: ipmmu-vmsa: Add r8a7744 support
iommu/amd: Move iommu_init_pci() to .init section
iommu/arm-smmu: Support non-strict mode
iommu/io-pgtable-arm-v7s: Add support for non-strict mode
iommu/arm-smmu-v3: Add support for non-strict mode
iommu/io-pgtable-arm: Add support for non-strict mode
iommu: Add "iommu.strict" command line option
iommu/dma: Add support for non-strict mode
iommu/arm-smmu: Ensure that page-table updates are visible before TLBI
iommu/arm-smmu-v3: Implement flush_iotlb_all hook
iommu/arm-smmu-v3: Avoid back-to-back CMD_SYNC operations
iommu/arm-smmu-v3: Fix unexpected CMD_SYNC timeout
iommu/io-pgtable-arm: Fix race handling in split_blk_unmap()
iommu/arm-smmu-v3: Fix a couple of minor comment typos
iommu: Fix a typo
iommu: Remove .domain_{get,set}_windows
iommu: Tidy up window attributes
...
Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
fpga
stm
extcon
nvmem
eeprom
hyper-v
gsmi
coresight
thunderbolt
vmw_balloon
goldfish
soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9Le5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn+BQCfZ6DtCIgqo0UW3dLV8Fd0wya9kw0AoNglzJJ6
YRZiaSdRiggARpNdh3ME
=97BX
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc patches for 4.20-rc1.
Loads of things here, we have new code in all of these driver
subsystems:
- fpga
- stm
- extcon
- nvmem
- eeprom
- hyper-v
- gsmi
- coresight
- thunderbolt
- vmw_balloon
- goldfish
- soundwire
along with lots of fixes and minor changes to other small drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (245 commits)
Documentation/security-bugs: Clarify treatment of embargoed information
lib: Fix ia64 bootloader linkage
MAINTAINERS: Clarify UIO vs UIOVEC maintainer
docs/uio: fix a grammar nitpick
docs: fpga: document programming fpgas using regions
fpga: add devm_fpga_region_create
fpga: bridge: add devm_fpga_bridge_create
fpga: mgr: add devm_fpga_mgr_create
hv_balloon: Replace spin_is_locked() with lockdep
sgi-xp: Replace spin_is_locked() with lockdep
eeprom: New ee1004 driver for DDR4 memory
eeprom: at25: remove unneeded 'at25_remove'
w1: IAD Register is yet readable trough iad sys file. Fix snprintf (%u for unsigned, count for max size).
misc: mic: scif: remove set but not used variables 'src_dma_addr, dst_dma_addr'
misc: mic: fix a DMA pool free failure
platform: goldfish: pipe: Add a blank line to separate varibles and code
platform: goldfish: pipe: Remove redundant casting
platform: goldfish: pipe: Call misc_deregister if init fails
platform: goldfish: pipe: Move the file-scope goldfish_pipe_dev variable into the driver state
platform: goldfish: pipe: Move the file-scope goldfish_pipe_miscdev variable into the driver state
...
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
This has been a smaller cycle with many of the commits being smallish code
fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full packet
mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user API, and
provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute groups
and cdev properly for uverbs, and clean up some of the core code's device list
management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and rework
how RDMA holds poitners to mm_struct for get_user_pages cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices
-----BEGIN PGP SIGNATURE-----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=pacJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle with many of the commits being smallish
code fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and
rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full
packet mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user
API, and provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute
groups and cdev properly for uverbs, and clean up some of the core
code's device list management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and
rework how RDMA holds poitners to mm_struct for get_user_pages
cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (242 commits)
IB/mlx5: Add support for extended atomic operations
RDMA/core: Fix comment for hw stats init for port == 0
RDMA/core: Refactor ib_register_device() function
RDMA/core: Fix unwinding flow in case of error to register device
ib_srp: Remove WARN_ON in srp_terminate_io()
IB/mlx5: Allow scatter to CQE without global signaled WRs
IB/mlx5: Verify that driver supports user flags
IB/mlx5: Support scatter to CQE for DC transport type
RDMA/drivers: Use core provided API for registering device attributes
RDMA/core: Allow existing drivers to set one sysfs group per device
IB/rxe: Remove unnecessary enum values
RDMA/umad: Use kernel API to allocate umad indexes
RDMA/uverbs: Use kernel API to allocate uverbs indexes
RDMA/core: Increase total number of RDMA ports across all devices
IB/mlx4: Add port and TID to MAD debug print
IB/mlx4: Enable debug print of SMPs
RDMA/core: Rename ports_parent to ports_kobj
RDMA/core: Do not expose unsupported counters
IB/mlx4: Refer to the device kobject instead of ports_parent
RDMA/nldev: Allow IB device rename through RDMA netlink
...
Implement PKCS#8 RSA Private Key format [RFC 5208] parser for the
asymmetric key type. For the moment, this will only support unencrypted
DER blobs. PEM and decryption can be added later.
PKCS#8 keys can be loaded like this:
openssl pkcs8 -in private_key.pem -topk8 -nocrypt -outform DER | \
keyctl padd asymmetric foo @s
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Tested-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Provide the missing asymmetric key subops for new key type ops. This
include query, encrypt, decrypt and create signature. Verify signature
already exists. Also provided are accessor functions for this:
int query_asymmetric_key(const struct key *key,
struct kernel_pkey_query *info);
int encrypt_blob(struct kernel_pkey_params *params,
const void *data, void *enc);
int decrypt_blob(struct kernel_pkey_params *params,
const void *enc, void *data);
int create_signature(struct kernel_pkey_params *params,
const void *data, void *enc);
The public_key_signature struct gains an encoding field to carry the
encoding for verify_signature().
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Tested-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Provide five keyctl functions that permit userspace to make use of the new
key type ops for accessing and driving asymmetric keys.
(*) Query an asymmetric key.
long keyctl(KEYCTL_PKEY_QUERY,
key_serial_t key, unsigned long reserved,
struct keyctl_pkey_query *info);
Get information about an asymmetric key. The information is returned
in the keyctl_pkey_query struct:
__u32 supported_ops;
A bit mask of flags indicating which ops are supported. This is
constructed from a bitwise-OR of:
KEYCTL_SUPPORTS_{ENCRYPT,DECRYPT,SIGN,VERIFY}
__u32 key_size;
The size in bits of the key.
__u16 max_data_size;
__u16 max_sig_size;
__u16 max_enc_size;
__u16 max_dec_size;
The maximum sizes in bytes of a blob of data to be signed, a signature
blob, a blob to be encrypted and a blob to be decrypted.
reserved must be set to 0. This is intended for future use to hand
over one or more passphrases needed unlock a key.
If successful, 0 is returned. If the key is not an asymmetric key,
EOPNOTSUPP is returned.
(*) Encrypt, decrypt, sign or verify a blob using an asymmetric key.
long keyctl(KEYCTL_PKEY_ENCRYPT,
const struct keyctl_pkey_params *params,
const char *info,
const void *in,
void *out);
long keyctl(KEYCTL_PKEY_DECRYPT,
const struct keyctl_pkey_params *params,
const char *info,
const void *in,
void *out);
long keyctl(KEYCTL_PKEY_SIGN,
const struct keyctl_pkey_params *params,
const char *info,
const void *in,
void *out);
long keyctl(KEYCTL_PKEY_VERIFY,
const struct keyctl_pkey_params *params,
const char *info,
const void *in,
const void *in2);
Use an asymmetric key to perform a public-key cryptographic operation
a blob of data.
The parameter block pointed to by params contains a number of integer
values:
__s32 key_id;
__u32 in_len;
__u32 out_len;
__u32 in2_len;
For a given operation, the in and out buffers are used as follows:
Operation ID in,in_len out,out_len in2,in2_len
======================= =============== =============== ===========
KEYCTL_PKEY_ENCRYPT Raw data Encrypted data -
KEYCTL_PKEY_DECRYPT Encrypted data Raw data -
KEYCTL_PKEY_SIGN Raw data Signature -
KEYCTL_PKEY_VERIFY Raw data - Signature
info is a string of key=value pairs that supply supplementary
information.
The __spare space in the parameter block must be set to 0. This is
intended, amongst other things, to allow the passing of passphrases
required to unlock a key.
If successful, encrypt, decrypt and sign all return the amount of data
written into the output buffer. Verification returns 0 on success.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Tested-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Provide five new operations in the key_type struct that can be used to
provide access to asymmetric key operations. These will be implemented for
the asymmetric key type in a later patch and may refer to a key retained in
RAM by the kernel or a key retained in crypto hardware.
int (*asym_query)(const struct kernel_pkey_params *params,
struct kernel_pkey_query *info);
int (*asym_eds_op)(struct kernel_pkey_params *params,
const void *in, void *out);
int (*asym_verify_signature)(struct kernel_pkey_params *params,
const void *in, const void *in2);
Since encrypt, decrypt and sign are identical in their interfaces, they're
rolled together in the asym_eds_op() operation and there's an operation ID
in the params argument to distinguish them.
Verify is different in that we supply the data and the signature instead
and get an error value (or 0) as the only result on the expectation that
this may well be how a hardware crypto device may work.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Tested-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance is
much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular hardware
bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJb0FINAAoJEED/6hsPKofoI60IAJRS3vOAQ9Fav8cJsO1oBHcX
3+NexfnBke1bzrjIR3SUcHKGZbdnVPNZc+Q4JjIbPpPmmOMU5jc9BC1dmd5f4Vzh
BMnQ0yCvgFv3A3fy/Icx1Z8NJppxosdmqdQLrQrNo8aD3cjnqY2yQixdXrAfzLzw
XEgKdIFCCz8oVN/C9TT4wwJn6l9OE7BM5bMKGFy5VNXzMu7t64UDOLbbjZxNgi1g
teYvfVGdt5mH0N7b2GPPWRbJmgnz5ygVVpVNQUEFrdKZoCm6r5u9d19N+RRXAwan
ZYFj10W2T8pJOUf3tryev4V33X7MRQitfJBo4tP5hZfi9uRX89np5zP1CFE7AtY=
=yEPW
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- Improved guest IPA space support (32 to 52 bits)
- RAS event delivery for 32bit
- PMU fixes
- Guest entry hardening
- Various cleanups
- Port of dirty_log_test selftest
PPC:
- Nested HV KVM support for radix guests on POWER9. The performance
is much better than with PR KVM. Migration and arbitrary level of
nesting is supported.
- Disable nested HV-KVM on early POWER9 chips that need a particular
hardware bug workaround
- One VM per core mode to prevent potential data leaks
- PCI pass-through optimization
- merge ppc-kvm topic branch and kvm-ppc-fixes to get a better base
s390:
- Initial version of AP crypto virtualization via vfio-mdev
- Improvement for vfio-ap
- Set the host program identifier
- Optimize page table locking
x86:
- Enable nested virtualization by default
- Implement Hyper-V IPI hypercalls
- Improve #PF and #DB handling
- Allow guests to use Enlightened VMCS
- Add migration selftests for VMCS and Enlightened VMCS
- Allow coalesced PIO accesses
- Add an option to perform nested VMCS host state consistency check
through hardware
- Automatic tuning of lapic_timer_advance_ns
- Many fixes, minor improvements, and cleanups"
* tag 'kvm-4.20-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
KVM/nVMX: Do not validate that posted_intr_desc_addr is page aligned
Revert "kvm: x86: optimize dr6 restore"
KVM: PPC: Optimize clearing TCEs for sparse tables
x86/kvm/nVMX: tweak shadow fields
selftests/kvm: add missing executables to .gitignore
KVM: arm64: Safety check PSTATE when entering guest and handle IL
KVM: PPC: Book3S HV: Don't use streamlined entry path on early POWER9 chips
arm/arm64: KVM: Enable 32 bits kvm vcpu events support
arm/arm64: KVM: Rename function kvm_arch_dev_ioctl_check_extension()
KVM: arm64: Fix caching of host MDCR_EL2 value
KVM: VMX: enable nested virtualization by default
KVM/x86: Use 32bit xor to clear registers in svm.c
kvm: x86: Introduce KVM_CAP_EXCEPTION_PAYLOAD
kvm: vmx: Defer setting of DR6 until #DB delivery
kvm: x86: Defer setting of CR2 until #PF delivery
kvm: x86: Add payload operands to kvm_multiple_exception
kvm: x86: Add exception payload fields to kvm_vcpu_events
kvm: x86: Add has_payload and payload to kvm_queued_exception
KVM: Documentation: Fix omission in struct kvm_vcpu_events
KVM: selftests: add Enlightened VMCS test
...
Pull cgroup updates from Tejun Heo:
"All trivial changes - simplification, typo fix and adding
cond_resched() in a netclassid update loop"
* 'for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, netclassid: add a preemption point to write_classid
rdmacg: fix a typo in rdmacg documentation
cgroup: Simplify cgroup_ancestor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=N+Ts
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Fix two more locations where printf formatting leaked pointers
- Better log_buf_len parameter handling
- Add prefix to messages from printk code
- Do not miss messages on other consoles when the log is replayed on a
new one
- Reduce race between console registration and panic() when the log
might get replayed on all consoles
- Some cont buffer code clean up
- Call console only when there is something to do (log vs cont buffer)
* tag 'printk-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
lib/vsprintf: Hash printed address for netdev bits fallback
lib/vsprintf: Hash legacy clock addresses
lib/vsprintf: Prepare for more general use of ptr_to_id()
lib/vsprintf: Make ptr argument conts in ptr_to_id()
printk: fix integer overflow in setup_log_buf()
printk: do not preliminary split up cont buffer
printk: lock/unlock console only for new logbuf entries
printk: keep kernel cont support always enabled
printk: Give error on attempt to set log buffer length to over 2G
printk: Add KBUILD_MODNAME and remove a redundant print prefix
printk: Correct wrong casting
printk: Fix panic caused by passing log_buf_len to command line
printk: CON_PRINTBUFFER console registration is a bit racy
printk: Do not miss new messages when replaying the log
Rick reported that the BPF JIT could potentially fill the entire module
space with BPF programs from unprivileged users which would prevent later
attempts to load normal kernel modules or privileged BPF programs, for
example. If JIT was enabled but unsuccessful to generate the image, then
before commit 290af86629 ("bpf: introduce BPF_JIT_ALWAYS_ON config")
we would always fall back to the BPF interpreter. Nowadays in the case
where the CONFIG_BPF_JIT_ALWAYS_ON could be set, then the load will abort
with a failure since the BPF interpreter was compiled out.
Add a global limit and enforce it for unprivileged users such that in case
of BPF interpreter compiled out we fail once the limit has been reached
or we fall back to BPF interpreter earlier w/o using module mem if latter
was compiled in. In a next step, fair share among unprivileged users can
be resolved in particular for the case where we would fail hard once limit
is reached.
Fixes: 290af86629 ("bpf: introduce BPF_JIT_ALWAYS_ON config")
Fixes: 0a14842f5a ("net: filter: Just In Time compiler for x86-64")
Co-Developed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jann Horn <jannh@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: LKML <linux-kernel@vger.kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull more ->lookup() cleanups from Al Viro:
"Some ->lookup() instances are still overcomplicating the life
for themselves, open-coding the stuff that would be handled by
d_splice_alias() just fine.
Simplify a couple of such cases caught this cycle and document
d_splice_alias() intended use"
* 'work.lookup' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Document d_splice_alias() calling conventions for ->lookup() users.
simplify btrfs_lookup()
clean erofs_lookup()
Vignesh R