* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
Enable fast bcm4329 WIFI suspend/resume on Tegra2 board.
This patch allows the mach-tegra support to tell the tegra MMC host
controller to NOT turn off power for the MMC controller the WIFI part
lives behind. Thus bcm4329 firmware doesn't need to be reloaded.
Signed-off-by: Venkat Rao <vrao@broadcom.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
Convert ixp4xx, lpc32xx, mxc, netx, pxa, sa1100, tcc8k, tegra and u300
to use the generic mmio clocksource recently introduced.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since mandatory barriers may be used (explicitly or implicitly via readl
etc.) to ensure the ordering between Device and Normal memory accesses,
a DMB is not enough. This patch converts it to a DSB.
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra hardware design cannot reliably support an arbitrary set of keys
waking up the system. Modify wakeup logic so either any key wakes the
system up or none will do.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that irq.c is just an interface layer between the gic
and legacy_irq.c, move the contents of legacy_irq.c into
irq.c.
Signed-off-by: Colin Cross <ccross@android.com>
Tegra PM irq support is being improved, remove it for now
until the rest of the platform gets PM support.
Signed-off-by: Colin Cross <ccross@android.com>
Replace the ugly hack that inserts legacy irq controller calls
into the irq call paths by reading and replacing the gic irq
chip with the new gic arch extensions.
Signed-off-by: Colin Cross <ccross@android.com>
This patch updates the Tegra gpio chained IRQ handler to use the chained
IRQ enter/exit functions in order to function correctly on primary
controllers with different methods of flow control.
This is required for the GIC to move to fasteoi interrupt handling.
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the
ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine
Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have
SND_SOC_TEGRA_WM8903 depend on this.
[Redid ASoC diff so it applies. -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Seaboard derivate Kaen has a GPIO to mute the headphone output. Add a field
to tegra_wm8903_platform_data so the board files can pass the GPIO number
for that to the ASoC machine driver.
Also, initialize this new field to a "not present" value for Harmony.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the platform device in advance to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio driver will soon support more than just the Tegra Harmony board.
Rename the platform data header file and data type to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Checking 'rate < 0' doesn't work because 'rate' is unsigned.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Colin Cross <ccross@android.com>
Change b0f18edaf6
(arm: tegra: Remove unused bogus irq enable/disable magic)
introduces warnings:
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_resume':
arch/arm/mach-tegra/gpio.c:260: warning: unused variable 'i'
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_suspend':
arch/arm/mach-tegra/gpio.c:283: warning: unused variable 'i'
Fix them, and fix a coding style issue on the same lines.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Erik Gilling <konkers@konkers.net>
Remove the open coded access to irq_desc which will fail on sparse irq
and use the proper wrappers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
Initialize the PMIC voltage regulators and provide the supply map for
PCI-e clock supply. The rest of the supplies should be added together
with the drivers that use them.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On Harmony board PCI-e subsystem can be enabled only after certain
voltage regulators are on. One of the regulators is an internal
regulator on the PMIC and another one is controlled by a PMIC GPIO.
Addition of the voltage control to the Harmony PCI-e initialization
allows booting of kernel with CONFIG_TEGRA_PCI even if the PMIC driver
is not loaded. In this case the PCI-e initialization will fail
gracefully intead of hanging the system.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TrimSlice has MicroSD and standard MMC/SD slots.
Register sdhci devices and enable GPIOs for MMC/SD slot.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the final patch to enable audio support on Harmony. It additionally
relies on the latest ASoC branch being merged in, which provides the header
defining the gpio_base field in the WM8903 platform data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is the portion of the audio-related setup that relies additionally
on the latest Tegra I2C driver being merged.
* Define platform data for WM8903 audio codec
* Register WM8903 as an I2C device
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Register the base i2c busses on harmony. Devices coming at a later date,
but this allows for hand-probing of some of them at least.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Register the base i2c devices on seaboard. A few more are pending,
but it's a start.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This change includes everything required to enable audio on Harmony, except
those parts which rely on code not currently in Tegra's for-next branch, i.e.
except those parts which rely on merges of the Tegra I2C driver or latest
ASoC subsystem.
* Define GPIO names for audio-related GPIOs
* Set up platform data and platform device for ASoC machine driver
* Register audio-related platform devices
* Initialize audio-related clocks
* Correctly configure pinmux and GPIO enables for audio-related pins
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This ensures they're kept in sync between platform_data definitions and
the GPIO table initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently tegra_pcie_init is effectively called as subsys_initcall. With
multiplatform kernel this may cause hangs on boards that don't intend to
support Tegra2 PCI-e. Ensure that TrimSlice board code initializes PCI-e
only when actually running on the TrimSlice.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
Move tegra_pcie_power_off before tegra_pcie_power_on for clean addition
of PCIE power gating
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
tegra_dma_init currently simply bails out early if any initialization fails.
This skips various data-structure initialization. In turn, this means that
tegra_dma_allocate_channel can still hand out channels. In this case, when
tegra_dma_free_channel is called, which calls tegra_dma_cancel, the walking
on ch->list will OOPS since the list's next/prev pointers may still be
NULL.
To solve this, add an explicit "initialized" flag, only set this once _init
has fully completed successfully, and have _allocate_channel refuse to hand
out channels if this is not set.
While at it, simplify _init:
* Remove redundant memsets
* Use bitmap_fill to mark all channels as in-use up-front, and remove
some now-redundant bitmap initialization loops.
* Only mark a channel as free once all channel-related initialization has
completed.
Finally, the successful exit path from _init always has ret==0, so just
hard-code that return. The error path still returns ret.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The ASoC machine driver was written assuming my previous patch to add
complete support for these clocks, which named them cdev1/2. Rename
the clocks to match that, to avoid churn in the ASoC driver.
This rename also makes the clocks more consistent with other Tegra
clocks irrespective of any of that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The driver is tegra-i2s not just i2s. Rename the clocks to match, so that
clk_get_sys can look up by driver name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The following commit makes the Tegra APB DMA engine fail to initialize
correctly: 0cf6230af9
ARM: tegra: Move tegra_common_init to tegra_init_early
The reason is that tegra_init_early_ calls tegra_dma_init which calls
request_threaded_irq, which fails since the IRQ hasn't yet been marked
valid; that only happens in tegra_init_irq, which gets called after
tegra_init_early.
This used to work OK, since tegra_init_early was tegra_common_init, which
got called after tegra_init_irq, basically from the beginning of
tegra_harmony_init.
Solve this by converting tegra_dma_init to a postcore_initcall. This makes
it execute late enough that IRQs are marked valid, and avoids having to
add it back to every machine's init function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The current code support of dummy timers in absence of local
timer is compile time. This is an attempt to convert it to runtime
so that on few SOC version if the local timers aren't supported
kernel can switch to dummy timers. OMAP4430 ES1.0 does suffer from
this limitation.
This patch should not have any functional impact on affected
files.
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds board support for the Seaboard eval platform and some of the
derivatives that are very similar. Since they only differ in some very
minor ways, most of the code is shared.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Turns out MMC2 (the bayonet 4-lane port) wasn't enabled in the
original pinmux. Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add the 3 sdhci devices that are available on Harmony as
platform devices. Two go to slots (one 4-lane, one 8-lane),
and one goes to onboard wifi.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add a common location to register resources for used on-chip devices
that are commonly configured on boards. Devices will be added to this file
as more drivers are added that can make use of them.
This is based on work contributed by several people, most of it from
Colin Cross and Erik Gilling.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Move harmony over to use the new gpio config table instead of having
separate settings in various parts of the code.
(The tegra sdhci driver should have the tegra_gpio_* ops removed, but
that will be done separately from this change.)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
To give one place to setup the pins that are used as GPIOs instead
of as their pinmuxed functions. Specifying enabled as false explicitly
disables the gpio mode of that pin (if left on by firmware).
This should remove the need for calling these from specific drivers and
thus reduce tegra-specific code from them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
The option isn't terribly useful on other ARM platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Enable the cpu, emc (memory controller) and csite (debug and
trace controller) clocks during init to prevent them from
being disabled by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Enable the timer and rtc clocks to prevent them being
turned off by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move tegra_common_init to tegra_init_early, and set it
as the init_early entry in the machine struct.
Initializes the clocks earlier so that timers can enable
their clocks.
Also reorders the members in the Harmony and Trimslice
boards' machine structs to match the order they are
called in.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Peripheral clocks that have no clock enable bit in the
enable registers have their clk_num set to 0. Bit 0
in the clock enable registers is the CPU clock.
Prevent disables on these peripheral clocks from
accidentally disabling the CPU clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Call the clock's round_rate op, if it exists, before calling
the set_rate op. This will help later when dvfs is added,
dvfs needs to know what the final rate will be before the
frequency changes.
Also requires fixes to the round rate functions to ensure
calling round rate and then set rate will not cause the
frequency to be rounded down twice. When picking clock
divider values, the clock framework picks the closest
frequency that is lower than the requested frequency. If
the new frequency calculated from the divider value is
rounded down, and then passed to set_rate, it will get
rounded down again, possibly resulting in a frequency two
steps lower than the original requested frequency.
Fix the problem by rounding up when calculating the frequency
coming out of a clock divider, so if that frequency is
requested again, the same divider value will be picked.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Some peripheral clocks share enable bits. Refcount the enables so
that calling clk_disable on one clock will not turn off another
clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Correct max rates for pclk and sclk (Originally fixed by
Dima Zavin <dima@android.com>)
Correct max rate for plla (Originally fixed by
Stephen Warren <swarren@nvidia.com>)
Remove unnecessary no-op set_rate on audio clocks
Add clock lookup entries for grhost, bsea, and vde clocks
Update clock clookup entries for vcp, bsea, and vde clocks
Add shared clock entries for sclk and emc
Add a virtual cop clock to provide a reset op (Originally fixed by
Dima Zavin <dima@android.com>)
Pass set_rate on super clocks through to parent
Fix pllx frequency table entry for 608 MHz
Remove incorrect plla frequency table entries
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLLP registers are now being restored by the low-level resume code,
and the CPU may be running off PLLP, so don't touch them during clock
resume.
Save plld, plls, pllu, and audio clock during suspend (originally
fixed by Mayuresh Kulkarni <mkulkarni@nvidia.com>)
The lock time for plld is 1000 us, so increase the delay after
setting the PLLs.
Add a BUG_ON to ensure the size of the suspend context area is
correct.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The SDMMC controllers have extra bits in the clock source
register that adjust the delay between the clock and data
to compenstate for delays on the PCB. The values need to
be set from the clock code so the clock can be locked
during the read-modify-write on the clock source register.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Adjusts the minimum memory frequency when the cpu frequency
changes. The values are currently hardcoded to a reasonable
default. If memory frequency scaling is not enabled this
patch will have no effect.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add clock ops on the emc peripheral clock that call into the
emc driver to update the memory controller registers for the
new frequency. Tegra has an interlock between the clock
controller and the memory controller that prevents the new
register values from taking effect until the clock frequency
update occurs.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Remove unnecessary uses of #ifdef CONFIG_DEBUG_FS
Convert bool assignments from 1 to true
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Some clocks may have multiple downstream users that need to request a
higher clock rate. Shared bus clocks provide a unique shared_bus_user
clock to each user. The frequency of the bus is set to the highest
enabled shared_bus_user clock, with a minimum value set by the
shared bus. Drivers can use clk_enable and clk_disable to enable
or disable their requirement, and clk_set_rate to set the minimum rate.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
During cpu frequency changes, take an extra reference to pllx so
that it doesn't turn off and on while the cpu is temporarily on
pllp. If the cpu is moved to pllp permanently, pllx will be
turned off.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Give each clock its own lock, and remove all lock traversals from
parent to child clocks to prevent AB-BA deadlocks.
This brings the locking in line with the common struct clk
patches and should make conversion simple.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Creates a union of a struct for each type of clock to reduce memory
usage and clarify which members are used by all clocks and which are
used by a single type.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Make the static clocks look more like the array of clocks
so they can all be initalized with the same helper function.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLL lock bits are not reliable, use per-PLL timeouts instead.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Drop the unnecessary pr_debug calls to avoid having to maintain them.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
When updating the CPU PLL frequency, keeping the PLL enabled avoids
ramping the PLL all the way down and back up again. Remove the BUG_ON
in tegra2_pll_clk_set_rate to allow the rate to change while the PLL
is enabled.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add a new 'reset' clk op. This can be provided for any clock,
not just peripherals.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
This seems to be a regression in 2.6.37.
We cannot use writel() here since the resulting wmb() calls l2x0_cache_sync()
which uses a spinlock and L1 cache may be off at this point.
http://lists.infradead.org/pipermail/linux-arm-kernel/2011-February/041909.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Colin Cross <ccross@android.com>
If a request already in the queue is passed to tegra_dma_enqueue_req,
tegra_dma_req.node->{next,prev} will end up pointing to itself instead
of at tegra_dma_channel.list, which is the way a the end-of-list
should be set up. When the DMA request completes and is list_del'd,
the list head will still point at it, yet the node's next/prev will
contain the list poison values. When the next DMA request completes,
a kernel panic will occur when those poison values are dereferenced.
This makes the DMA driver more robust in the face of buggy clients.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sometimes, due to high interrupt latency in the continuous mode
of DMA transfer, the half buffer complete interrupt is handled
after DMA has transferred the full buffer. When this is detected,
stop DMA immediately and restart with the next buffer if the next
buffer is ready.
originally fixed by Victor(Weiguo) Pan <wpan@nvidia.com>
In place of using the simple spin_lock()/spi_unlock() in the
interrupt thread, using the spin_lock_irqsave() and
spin_unlock_irqrestore(). The lock is shared between the normal
process context and interrupt context.
originally fixed by Laxman Dewangan (ldewangan@nvidia.com)
The use of shadow registers caused memory corruption at physical
address 0 because the enable bit was not shadowed, and assuming it
needed to be set would enable an unconfigured dma block. Most of the
register accesses don't need to know the previous state of the
registers, and the few places that do need to modify only a few bits
in the registers are the same ones that were sometimes incorrectly
setting the enable bit. This patch convert tegra_dma_update_hardware
to set the entire register, and the other users to read-modify-write,
and drops the shadow registers completely.
Also fixes missing locking in tegra_dma_allocate_channel
Signed-off-by: Colin Cross <ccross@android.com>
On Tegra, calling clk_set_rate on the CPU clock may call into the
regulator API. If the regulator driver that controls the CPU
voltage rail has been suspended, this can lead to attempted
communication with a hardware block that has already been turned
off.
Adds a SUSPEND_PREPARE notification hook to drop the frequency to
the lowest possible during suspend.
Also adds 216MHz (off of PLLP) as the lowest CPU frequency, which
allows PLLX to be turned off.
Signed-off-by: Colin Cross <ccross@android.com>
Adds gart, hdmi, avp, host1x, and pwm controllers to mach/iomap.h
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement read_persistent_clock by reading the Tegra RTC
registers that stay running during suspend.
Save and restore the timer configuration register in
suspend.
Signed-off-by: Colin Cross <ccross@android.com>
Adds missing drive pingroups, saves all drive pingroups in
suspend, and restores the pinmux registers in the proper order.
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Save and restore pll and osc state during suspend
Add digital audio clocks
Update clk dev associations
Correct max clock frequencies
Add pll_p as additional cpu clock state
Add values to plld table
Fix register offset for sdmmc4 clock
Add blink timer to tegra2_clocks
Signed-off-by: Colin Cross <ccross@android.com>
Add fields to describe all the audio-related GPIOs on Harmony, except for
the codec's GPIO IRQ, which will be passed in its i2c_board_info.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future patch will export gic_mask_irq and gic_unmask_irq.
Rename the pointers in arch/arm/mach-tegra/irq.c to avoid
a compile error.
Signed-off-by: Colin Cross <ccross@android.com>
Commit 37337a8d5e, "ARM: tegra: irq_data
conversion." missed changing one reference to 'irq' in the function
tegra_gpio_irq_set_type(). This patch fixes the build error.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@google.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
e3d9c625 (ARM: CPU hotplug: fix hard-coded control register constants)
changed the wrong constants in the hotplug assembly code. Fix this.
Reported-by: viresh kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SDHCI driver for Tegra. This driver plugs in as a new variant of
sdhci-pltfm, using the platform data structure passed in to specify the
GPIOs to use for card detect, write protect and card power enablement.
Original driver (of which only the header file is left):
Signed-off-by: Yvonne Yip <y@palm.com>
The rest, which has been rewritten by now:
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tegra_clocksource_read should not use cnt32_to_63, wrapping is
already handled in the clocksource code. Move the cnt32_to_63
into the sched_clock function, and replace the use of clocksource
mult and shift with a multiplication by 1000 to convert us to ns.
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original scheme for reporting spurious wakeups was broken - it
tried to use printk() from a context which wasn't coherent with the
other CPUs, which risks corrupting the printk() data.
Fix this by noting the number spurious wakeups, and only report them
when we are properly woken - when we will be coherent with the rest
of the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Milo is an old boot loader, which is no longer relevant for these
platforms. References to it are misleading. Move the code out
of poke_milo(), and remove references to milo in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the Tegra subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 0ea1293009 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds