Should be called for all incoming packets and not just for GRO packets
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-ordering the statistics to enhance readability and adding per queue
statistics (available via ethtool -S)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This check is unreliable since latest MC can issue warnings on rare occasions
which are not fatal errors
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initializing the chip after iSCSI boot, the interrupts of the function
that was used to boot must be disabled. That means that the driver needs to set
the chip as if it is the iSCSI PCI function - this bug is exposed only with MSI
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling MSI on top of MSI-X and INTA. Also changing the module parameter to
allow choosing INTA or MSI even when MSI-X is available. The default status
block should not be reversed for endianity. Since MSI can issue
re-configuration, the interrupt disable function now requires mmiowb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Tx multi-queue and enabling multi-queue by default
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the FW blob and the relevant definitions without any logic. It
also contains the minimal mandatory code changes to work with this FW
but it does not contain enabling of the new features that this FW
provides.
This FW is needed for:
- More efficient multi-queue
- per queue statistics
- Big-endian issue with MSI
- Improved pause response
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TX and RX hardware time stamping are implemented. Due to
hardware limitations it is not possible to verify reliably which
packet was time stamped when multiple were pending for sending; this
could be solved by only allowing one packet marked for hardware time
stamping into the queue (not implemented yet).
RX time stamping relies on the flag in the packet descriptor which
marks packets that were time stamped. In "all packet" mode this flag
is not set. TODO: also support that mode (even though it'll suffer
from race conditions).
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the register definitions and code to read the time
register.
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single-thread access must be ensured for ICH8 NVM and PHY operations.
This synchronization is provided by the nvm_mutex. To assist in
understanding the contexts from which this code could be reached,
a WARN was output if the mutex was not going to be immediately
acquirable (if !mutex_trylock()). The code has now been optimized,
and we have verified that the few remaining mutex contentions are
reasonable and non-blocking, and it is time to remove the
mutex_trylock() and WARN messages.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32 directly as it handles constant folding now, replace direct
uses of __constant_cpu_to_{endian} as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forward-porting the tun accounting patch I managed to break
the send path compltely by dropping the tun_get call.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need the udelay() for all families, including AR5416.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The test to find out if we have FAT channels do not consider that
the value of regulatory_bands for the 5000 series is larger than its
eeprom size. Using the eeprom size is strange in itself.
Use a new EEPROM_REGULATORY_BAND_NO_FAT to indicate no FAT support
and test for that explicitly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch remove w/a used for development boards.
These boards are not available thus no need to keep it inside driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the code from mac80211 to keep track of BSSes
and use the cfg80211-provided code completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes zd1211rw honour enable_beacon, as well as fixing
a memory leak: the beacon skb is leaked when configuring it
to the hardware fails.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is rather confusing to see this in the log:
[ 695.606877] __ratelimit: 40 callbacks suppressed
[ 700.726878] __ratelimit: 40 callbacks suppressed
without ever seeing any actual message. This is because
zd1211rw doesn't compile out the net_ratelimit() call
properly if debugging is not enabled.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the various function pointer
assignments and unifies them in a single ops structure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is preparatory work for removing the individual
function pointer assignments in eeprom.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few variables (bssid, bssidmask, curaid) were duplicated in
struct ath_softc and in ath_hal, remove them.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the HW version/revision specific
information into a separate structure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the useless sc_ prefixes for all variables.
Also, refer to interfaces as VIFs and not as VAPs anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the ANI channel reference to a pointer,
this facilitates moving struct ar5416AniState to ani.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the core header files into manageable pieces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* We call reset too often and this can result various PHY problems.
On config_interface we don't need to reset the whole device.
TODO: Create a function hw_fast_reset that only resets the PCU
(tx/rx stuff) and not the whole device so that we can use this for
stuck beacons etc.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't enable BMISS interrupts as we don't handle them yet
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update reset and sync with HALs
* Clean up eeprom settings and tweaking of initvals and
put them on separate functions
* Set/Restore 32KHz ref clk operation
* Add some more documentation
TODO: Spur mitigation, tpc, half/quarter rate, compression etc
v2: Address comments from Bob and Felix and fix RSSI threshold bug
introduced on the first version of the patch
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update initvals to match legacy and Sam's HAL
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use the new way to modify rf buffer and put some rf buffer
documentation on rfbufer.h
* Merge all rf regs functions to one
* Sync with legacy HAL and Sam's HAL
* Set gain_F settings so that gain_F optimization engine works
on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
and they don't use gain_F optimization for this chip, code is
there but is never used)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update and cleanup rf gain optimization code
* Add comments and refferences to docs and use sane function names
* Use only step index on ath5k_gain, no need to have a pointer to
the current step since we can determine te step from it's index,
this also allows us to put all other structs on rfgain.h and cleanup
ath5k.h a little
* No need for ah_rfgain variable, we use ah_gain.g_state for everything
* Tested on RF2112B chip but gain_F calibration is not yet done
(we will finish this on the next patch where we'll rewrite rf-buffer
handling)
* Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch
It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
new way to access specific rf registers (will use it later)
* Clean up initial rf gain settings by moving them on a new file (rfgain.h)
so we can later work on gain optimization functions
* Update initial rf buffer settings and initial rf gain settings from HALs.
This breaks things for now because our current dumps come from pre-configured
rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just compile it into the orinoco module. If we merge USB support, the
module can then be split as appropriate.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... when used by the WEXT ioctl functions. This will allow us to
separate the card specific stuff from the WEXT code.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eilon Greenstein