We shouldn't set HNAE3_NONE_RESET bit of the variable that represents a
reset request during handling of MSI-X errors, or may cause issue when
trigger reset.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LINK_UP and LINK_DOWN are two bits of MAC tunnel interrupts, but previous
HNS3 driver didn't handle them. If they were enabled, value of these two
bits will change during link down and link up, which will cause HNS3
driver keep receiving IRQ but can't handle them.
This patch adds handling of these two bits of interrupts, we will record
and clear them as what we do to other MAC tunnel interrupts.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hclge/hclgevf and hns3 module can be unloaded independently,
when hclge/hclgevf unloaded firstly, the ops of ae_dev should
be set to NULL, otherwise it will cause an use-after-free problem.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we add a VF without loading hclgevf.ko and then there is a RAS error
occurs, PCIe AER will call error_detected and slot_reset of all functions,
and will get a NULL pointer when we check ad_dev->ops->handle_hw_ras_error.
This will cause a call trace and failures on handling of follow-up RAS
errors.
This patch check ae_dev and ad_dev->ops at first to solve above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the port shaper according to the MAC speed as
suggested by hardware user manual.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, the driver only restore VLAN filter entries
for PF after reset, the VLAN entries of VF will lose in this
case.
This patch fixes it by recording VLAN IDs for each function
when add VLAN, and restore the VLAN IDs after reset.
Fixes: 681ec3999b ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since core reset is similar to the global reset, so this
patch removes it and uses global reset to replace it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing a loopback test at copper ports, the serdes loopback
and the phy loopback will fail, because of the adjust link had
not finished, and phy not ready.
Adds sleep between adjust link and test process to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hclge_bind_ring_with_vector() fails,
hclge_map_unmap_ring_to_vf_vector() returns the error
directly, so nobody will free the memory allocated by
hclge_get_ring_chain_from_mbx().
So hclge_free_vector_ring_chain() should be called no matter
hclge_bind_ring_with_vector() fails or not.
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_uninit_phy() should be called before checking
HNS3_NIC_STATE_INITED flags, otherwise when this checking fails,
there is nobody to call hns3_uninit_phy().
Fixes: c8a8045b2d ("net: hns3: Fix NULL deref when unloading driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading driver, the reset task should not be scheduled
anymore. If disable IRQ before cancel ongoing reset task,
the IRQ may be re-enabled by the reset task.
This patch uses HCLGE_STATE_REMOVING/HCLGEVF_STATE_REMOVING
flag to indicate that the driver is unloading, and we should
stop new coming reset service to be scheduled, otherwise,
reset service will access some resource which has been freed
by unloading.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reset happens, the hardware reset should begin after the
driver has finished its preparatory work, otherwise it may cause
some hardware error.
Before Hardware's reset, it will wait for the driver to write
bit HCLGE_NIC_CMQ_ENABLE of register HCLGE_NIC_CSQ_DEPTH_REG
to 1, while the driver finishes its preparatory work will do that.
BTW, since some cases this register will be cleared, so it needs
some sync time before driver's writing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclgevf_init_client_instance() is a little bloated and there is
some duplicated code. This patch adds some cleanup for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_init_client_instance() is a little bloated and there is
some duplicated code. This patch adds some cleanup for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGEVF_STATE_NIC_REGISTERED
to indicate that. And before calling VF NIC client's uninit_instance(),
we clear this state.
So any operation of VF NIC client from HCLGEVF is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF ROCE client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_ROCE_REGISTERED
to indicate that. And before calling PF ROCE client's uninit_instance(),
we clear this state.
So any operation of the ROCE client from HCLGE is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_NIC_REGISTERED
to indicate that. And before calling PF NIC client's uninit_instance(),
we clear this state.
So any operation of PF NIC client from HCLGE is not allowed if this
state is not set.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user menual, the GRO_SIZE is 14 bits width,
the HNS3_RXD_GRO_SIZE_M is 10 bits width now, which may cause
hardware GRO received packet error problem.
Fixes: a6d53b97a2 ("net: hns3: Adds GRO params to SKB for the stack")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifdef condition of function hclge_add_fd_entry_by_arfs() is
unnecessary. It may cause compile warning when CONFIG_RFS_ACCEL
is not chosen. This patch fixes it by removing the ifdef condition.
Fixes: d93ed94fbe ("net: hns3: add aRFS support for PF")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC capbility may be changed with port speed changes. Driver
needs to read the active FEC mode, and update FEC capability
when port speed changes.
Fixes: 7e6ec9148a ("net: hns3: add support for FEC encoding control")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate CPU rmap and add entry for each irq. CPU rmap is
used in aRFS to get the queue number of the rx completion
interrupts.
In additional, remove the calling of
irq_set_affinity_notifier() in hns3_nic_init_irq(), because
we have registered notifier in irq_cpu_rmap_add() for each
vector, otherwise it may cause use-after-free issue.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Å tetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses devm_kcalloc instead of kcalloc when allocating
ring->desc_cb, because devm_kcalloc not only ensure to free the
memory when the dev is deallocted, but also allocate the memory
from it's device memory node.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some unused field in struct hns3_enet_ring,
use ring->dev for ring_to_dev macro, and use dev consistently
in hns3_fill_desc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When page size is 64K, RX buffer is currently not reused when the
page_offset is moved to last buffer. This patch adds checking to
decide whether the buffer page can be reused when last_offset is
moved beyond last offset.
If the driver is the only user of page when page_offset is moved
to beyond last offset, then buffer can be reused and page_offset
is set to zero.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a barrier is used when cleaning each TX BD, which may
cause performance degradation.
This patch optimizes it to use one barrier when cleaning TX BD
each round.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When desc filling fails in hns3_nic_net_xmit, it will call
hns3_clear_desc to unmap the dma mapping. But currently the
ring->next_to_use points to the desc where the desc filling
or dma mapping return error, which means the desc that
ring->next_to_use points to has not done the dma mapping,
the desc that need unmapping is before the ring->next_to_use.
This patch fixes it by calling ring_ptr_move_bw(next_to_use)
before doing unmapping operation, and set desc_cb->dma to
zero to avoid freeing it again when unloading.
Also, when filling skb head or frag fails, both need to unmap
all the way back to next_to_use_head, so remove one desc filling
error handling.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling len and checksum info to description, there is some
similar checking or calculation.
So this patch adds hns3_set_l2l3l4 to fill the inner(/normal)
header's len and checksum info. If it is a encapsulation skb, it
calls hns3_set_outer_l2l3l4 to handle the outer header's len and
checksum info, in order to avoid some similar checking or
calculation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the inner and outer l2l3l4 len handling in
hns3_set_l2l3l4_len, this is a preparation to combine the l2l3l4
len and checksum handling for inner and outer header.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user manual, the tunnel packet type is
available in the rx.ol_info field of struct hns3_desc. Currently
the tunnel packet type is decided by the rx.l234_info, which may
cause RX checksum handling error.
This patch fixes it by using the correct field in struct hns3_desc
to decide the tunnel packet type.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW requires every continuous 8 buffer data to be larger than MSS,
we simplify it by ensuring skb_headlen + the first continuous
7 frags to to be larger than GSO header len + mss, and the
remaining continuous 7 frags to be larger than MSS except the
last 7 frags.
This patch adds hns3_skb_need_linearized to handle it for TSO
case.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, using "ethtool --statistics" can show how many time RX
page have been reused, but there is no counter for RX page not
being reused.
This patch adds non_reuse_pg counter to better debug the performance
issue, because it is hard to determine when the RX page is reused
or not if there is no such counter.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule_irqoff is introduced to be used from hard interrupts
handlers or when irqs are already masked, see:
https://lists.openwall.net/netdev/2014/10/29/2
So this patch replaces napi_schedule with napi_schedule_irqoff.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, maybe_stop_tx ops for TSO and non-TSO case share some BD
calculation code, so this patch unifies the maybe_stop_tx by removing
the maybe_stop_tx ops. skb_is_gso() can be used to differentiate the
case between TSO and non-TSO case if there is need to handle special
case for TSO case.
This patch also add tx_copy field in "ethtool --statistics" to help
better debug the performance issue caused by calling skb_copy.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.
The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes
In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).
If not modified, the loopback test returns probability failure.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375b ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
PF supports all debugfs command, but VF only supports part of
debugfs command. So VF should not show unsupported help information.
This patch adds a check for PF and PF to show the supportable help
information.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates VF's TQP statistic info in the service task,
and adds a limitation to prevent update too frequently.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.
The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.
In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allow users to dump content of NCL_CONFIG by using debugfs
command.
Command format:
echo dump ncl_config <offset> <length> > cmd
It will print as follows:
hns3 0000:7d:00.0: offset | data
hns3 0000:7d:00.0: 0x0000 | 0x00000020
hns3 0000:7d:00.0: 0x0004 | 0x00000400
hns3 0000:7d:00.0: 0x0008 | 0x08020401
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for network interface message level
settings. The message level can be changed by module parameter
or ethtool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function hns3_get_tx_timeo_queue_info(), it should use
netdev->num_tx_queues, instead of netdve->real_num_tx_queues
as the loop limitation.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current codes, tx_timeout_cnt is used before increased,
then we can see the tx_timeout_count is still 0 from the
print when tx timeout happens, e.g.
"hns3 0000:7d:00.3 eth3: tx_timeout count: 0, queue id: 0, SW_NTU:
0xa6, SW_NTC: 0xa4, HW_HEAD: 0xa4, HW_TAIL: 0xa6, INT: 0x1"
The tx_timeout_cnt should be updated before used.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When wait for response timeout or response code not match, there
should be more information for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When received vector0 msix and other event interrupt, it should
print the value of the register for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some statistics for VF reset.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).
So this patch fixes it by using u32 for vport->bw_limit.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameter "proto" in function hclge_set_vlan_filter_hw()
is asked to be __be16, but got u16 when calling it in function
hclge_update_port_base_vlan_cfg().
This patch fixes it by converting it with htons().
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 21e043cd81 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some redundant BH disable when initializing
and uninitializing command queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is pending skb in RX flow when close the port, and the
pending buffer is not cleaned, the new packet will be added to
the pending skb when the port opens again, and the first new
packet has error data.
This patch cleans the pending skb when clean RX ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some cases, PHY may not be connected to MDIO bus, then
the driver will initialize fail since MDIO bus initialization
fails.
This patch fixes it by skipping the MDIO bus initialization
when PHY is inexistent.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware description, reset level that should be
triggered are not consistent in a module. For example, in SSU
common errors, the first two bits has no need to do reset,
but the other bits need global reset.
This patch sets separate reset level for all RAS and MSI-X
interrupts by adding a reset_lvel field in struct hclge_hw_error,
and fixes some incorrect reset level.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hardware may have not enough buffer to receive packet
when it has used more than two MPS(maximum packet size) of
buffer, but there are still a lot of shared buffer left unused
when TC num is small.
This patch divides shared buffer to be used between TC when
the port supports DCB, and adjusts the waterline and threshold
according to user manual for the port that does not support
DCB.
This patch also change hclge_get_tc_num's return type to u32
to avoid signed-unsigned mix with divide.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RX shared buffer' threshold size for speific TC is
set to smaller value when the TC's PFC is not enabled, which may
cause performance problem because hardware may not have enough
hardware buffer when PFC is not enabled.
This patch sets the same threshold size for all TC no matter if
the specific TC's PFC is enabled.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a GRO packet is received by driver, the cwr field in the
struct tcphdr needs to be checked to decide whether to set the
SKB_GSO_TCP_ECN for skb_shinfo(skb)->gso_type.
So this patch adds hns3_gro_complete to do that, and adds the
hns3_handle_bdinfo to handle the hns3_gro_complete and
hns3_rx_checksum.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the parameters of hns3_rx_checksum to be more specific to
what is used internally, rather than passing in a pointer to the
whole hns3_desc. Reduces duplicate code and bring this function
inline with the approach used in hns3_set_gro_param.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
This patch fixes it. When VF loads up, it firstly queries the port
based VLAN state from PF. When user change port based VLAN state
from PF, PF firstly checks whether the VF is alive. If the VF is
alive, then PF notifies the VF the modification; otherwise PF
configure the port based VLAN state directly.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, ndo_set_vf_vlan() in hns3 driver was implemented
wrong. It adds or removes VLAN into VLAN filter for VF, but VF is
unaware of it.
Indeed, ndo_set_vf_vlan() is expected to enable or disable port based
VLAN (hardware inserts a specified VLAN tag to all TX packets for a
specified VF) . When enable port based VLAN, we use port based VLAN id
as VLAN filter entry. When disable port based VLAN, we use VLAN id of
VLAN device.
This patch fixes it for PF, enable/disable port based VLAN when calls
ndo_set_vf_vlan().
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in TX direction, driver implements the TX VLAN offload
by checking the VLAN header in skb, and filling it into TX descriptor.
Usually it works well, but if enable inserting VLAN header based on
port, it may conflict when out_tag field of TX descriptor is already
used, and cause RAS error.
In RX direction, hardware supports stripping max two VLAN headers.
For vlan_tci in skb can only store one VLAN tag, when RX VLAN offload
enabled, driver tells hardware to strip one VLAN header from RX
packet; when RX VLAN offload disabled, driver tells hardware not to
strip VLAN header from RX packet. Now if port based insert VLAN
enabled, all RX packets will have the port based VLAN header. This
header is useless for stack, driver needs to ask hardware to strip
it. Unfortunately, hardware can't drop this VLAN header, and always
fill it into RX descriptor, so driver has to identify and drop it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our hardware supports inserting a specified VLAN header for each
function when sending packets. User can enable it with command
"ip link set <devname> vf <vfid> vlan <vlan id>".
For this VLAN header is inserted by hardware, not from stack,
hardware also needs to strip it from received packets before
sending to stack. In this case, driver needs to tell
hardware which VLAN to insert or strip.
The current VLAN initialization doesn't allow inserting
VLAN header by hardware, this patch modifies it, in order be
compatible with VLAN inserted base on port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclgevf_client_start() fails or VF driver unloaded, there is
nobody to disable keep_alive_timer.
So this patch fixes them.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checking of HCLGEVF_STATE_RST_HANDLING flag in the
hclgevf_reset_task_schedule() will make some scheduling of
reset pending fail. This flag will be checked in the
hclgevf_reset_service_task(), it is unnecessary to check it
in the hclgevf_reset_task_schedule(). So this patch removes it.
Fixes: 35a1e50343 ("net: hns3: Add VF Reset Service Task to support event handling")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds error handler for the failure of command queue
initialization both PF and VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the command queue needs re-initialization, the mailbox handling
task should do nothing, otherwise this task will just get some error
print.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ongoing lower-level reset will fail when there is a higher-level
reset occurs, so the error handler should deal with this situation.
Fixes: 6a5f6fa382 ("net: hns3: add error handler for hclgevf_reset()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reset does not finish, the driver should not
request a new reset, otherwise the ongoing hardware reset
will get problem.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to deal with the new coming reset if
it is lower than the ongoing one.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the reset has been done successfully, the ongoing reset timer
is unnecessary.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_stop() should be called after unregister_netdev(),
otherwise the ongoing reset task may start the client just after it.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a vport is not alive, it is unnecessary to notify it to reset
before PF asserting a reset. So before inform vport to reset,
we need to check its alive state firstly.
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reinitializing, the vport alive state needs to be set up.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting, the vport alive state should be set to default,
otherwise the alive state of the vport whose driver not running
is wrong before the timer to check it out.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mskid is unsigned and hence comparisons with negative
error return values are always false. Fix this by making mskid an
int.
Fixes: f058e46855 ("net: hns: fix ICMP6 neighbor solicitation messages discard problem")
Addresses-Coverity: ("Operands don't affect result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some sparse warnings in the HNS drivers:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] <asn:2> *io_base
got void *vaddr
warning: cast removes address space '<asn:2>' of expression
[...]
Add __iomem and change all the u8 __iomem to void __iomem to
fix these kind of warnings.
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2> *base
got unsigned char [usertype] *base_addr
warning: cast to restricted __le16
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] tbl_tcam_data_high
got restricted __le32 [usertype]
warning: cast to restricted __le32
[...]
These variables used u32/u16 as their type, and finally as a
parameter of writel(), writel() will do the cpu_to_le32 coversion
so remove the little endian covert code to fix these kind of warnings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.
This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HNS driver loaded, always have an error print:
"netif_napi_add() called with weight 256"
This is because the kernel checks the NAPI polling weights
requested by drivers and it prints an error message if a driver
requests a weight bigger than 64.
So use NAPI_POLL_WEIGHT to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is trying to fix the issue due to:
[27237.844750] BUG: KASAN: use-after-free in hns_nic_net_xmit_hw+0x708/0xa18[hns_enet_drv]
After hnae_queue_xmit() in hns_nic_net_xmit_hw(), can be
interrupted by interruptions, and than call hns_nic_tx_poll_one()
to handle the new packets, and free the skb. So, when turn back to
hns_nic_net_xmit_hw(), calling skb->len will cause use-after-free.
This patch update tx ring statistics in hns_nic_tx_poll_one() to
fix the bug.
Signed-off-by: Liubin Shu <shuliubin@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hnae3_match_n_instantiate() was called both by
initializing or uninitializing client. For uninitializing, the
return value was never used.
To make it more clear, this patch splits it to two functions,
hnae3_init_client_instance() and hnae3_uninit_client_instance().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_reset_notify_uninit_enet() HNS3_NIC_STATE_INITED flag
should be checked and cleared firstly.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting, the changing of MTU is not allowed, so this patch
adds checking reset status in hns3_nic_change_mtu() to do that.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_get_stats() should check the resetting status firstly,
since the device will be reinitialized when resetting. If the
reset has not completed, the hns3_get_stats() may access
invalid memory.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used netdev->uc and netdev->mc list in function
hns3_recover_hw_addr() and hns3_remove_hw_addr().
We should add protect for them.
Fixes: f05e210971 ("net: hns3: Clear mac vlan table entries when unload driver or function reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
csq is used as a ring buffer, the value of the desc will be replaced
in next use. This patch removes the unnecessary memset, and just
updates the next_to_clean.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a likely case for hns3_fill_desc and
limits the local variables' scope as much as possible,
also avoid div operation when the tqp_vector->num_tqps
is one.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the ring_space by calculating the
ring space without calling ring_dist.
Also ring_dist is only used by ring_space, so this patch
removes it when it is no longer used.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set 2 same MAC to different function of one port, IMP
will return error as the later one may modify the origin one.
This will cause bond fail for 2 VFs of one port.
Driver just print warning and return 0 with this patch, so
if set same MAC address, it will return 0 but do not really
configure HW.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Method for obtaining the media type of the VF network port periodically,
regular tasks will not run until the network port UP. When the network
port is DOWN, the network port cannot obtain the media type.
Modifies the media type obtained when initializing the VF network port.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kdump kernel started, the HNS3 driver fail to register:
[14.753340] hns3 0000:7d:00.0: Alloc umv space failed, want 512, get 0
[14.795034] hns3 0000:7d:00.0: add uc mac address fail, ret =-22.
By default, the HNS3 driver will use about 512M memory, but
usually the reserved memory of kdump kernel is 576M, so the HNS3
driver fail to register. This patch reduces the memory use in
kdump kernel to about 16M.
And when the kdump kernel starts, we must clear ucast mac address
first to avoid add fail.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hip08 SOC does not support 1000M half, this patch adds 1000M half
check for hns3_ethtool_ops.set_link_ksettings, so the user can not
set 1000M half by ethtool.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the rules for configuring search paths in Kbuild have
changed, this will lead some erros when compiling hns3 with the
following command:
make O=DIR M=drivers/net/ethernet/hisilicon/hns3
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10:
fatal error: hnae3.h: No such file or directory
This patch fix it by adding $(srctree)/ prefix to the serach paths.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added IANA_VXLAN_UDP_PORT (4789) definition to vxlan header file so it
can be used by drivers instead of local definition.
Updated drivers which locally defined it as 4789 to use it.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Yunsheng Lin <linyunsheng@huawei.com>
Cc: Peng Li <lipeng321@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:414:6:
warning: symbol 'hclge_destroy_cmd_queue' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:407:6:
warning: symbol 'hclgevf_update_link_mode' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit bfcb79fca1
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.
This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.
This patch needs backporting to the kernel v5.0+
Fixes: 332fbf5765 ("net: hns3: add handling of hw ras errors using new set of commands")
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a couple logical ORs accidentally mixed in with the bitwise
ORs.
Fixes: e8149933b1 ("net: hns3: remove hnae3_get_bit in data path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(struct boo) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hns3_client_start() failed in the hns3_client_init(),
register_dev() should be undo in its error handling.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the hns reset_type for the roce errors is set
in the hclge_log_and_clear_rocee_ras_error function.
This function is also called to detect and clear roce errors
while enabling the rdma error interrupts. However there is no hns
reset requested for this case. This can cause issue of wrong
reset_type used with subsequent hns reset as the
reset_type set in the above case was not cleared.
This patch moves setting of hns reset_type for the roce errors from
hclge_log_and_clear_rocee_ras_error function
to hclge_handle_rocee_ras_error.
Fixes: 630ba007f4 ("net: hns3: add handling of RDMA RAS errors")
Reported-by: Huazhong Tan <tanhuazhong@huawei.com>
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, VF shares the same RSS config with PF.
In original codes, it always return 0 when query RSS hash
key for VF. This patch fixes it by return the hash key
got from PF.
Fixes: 374ad29176 ("net: hns3: net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x21, the switch of VF VLAN filter is per function.
It's necessary to enable VF VLAN filter for each VF when initializing.
Otherwise, VF will be able to receive broadcast packets with unknown
VLAN when PF enters promisc mode.
Fixes: 64d114f0a7 ("net: hns3: Add egress/ingress vlan filter for revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hnae3_get_bit uses hnae3_get_field, and hnae3_get_field
masks the data, which is unnecessary in data path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_set_bit and hnae3_set_field masks the data before setting
the field or bit, which is unnecessary because the data is already
zero initialized.
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely hint for error handling in critical data
path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fill_desc ops has only one implementation, and
get_rxd_bnum has not been used, so this patch removes
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits some variables' scope as much as possible in
hns3_fill_desc.
Also, only set l3_type and l4_type when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses shift offset to avoid doing mult and div operation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xps setting support for hns3 driver based on
the interrupt affinity info.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading VF driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Also this patch adds hclge_cmd_uninit() to do the command queue
uninitialization which includes clearing registers and freeing
memory.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify print message of 6th bit of ppp mpf abnormal errors,
there is a extra letter e in it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits are enabled now and have been test.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd and 4th of PPU(RCB) PF Abnormal is RAS errors instead of MSI-X
like other bits. This patch adds process of handling and logging this
two bits. Otherwise, this patch modifies print message of 28th and 29th
bit of PPU MPF Abnormal errors, which keep same with other errors now.
Fixes: f69b10b317 ("net: hns3: handle hw errors of PPU(RCB)")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add information of specific bit in log to be consistent
with other type of errors, so that we can know which memory of ssu
has occurred a ecc ras errors.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, for copper port which doesn't connect to phy,
it always returns -EOPNOTSUPP when query port information. This
patch fixes it by return the port information of MAC.
Fixes: 5f373b1585 ("net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link mode with bits has been up to more than 31 for some MAC
and phy. Convert to using a linkmode bitmap, which can support all
link modes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hnae3_register_ae_dev(), ae_algo->ops is assigned to ae_dev->ops
before check that ae_algo->ops is valid.
And in hnae3_register_ae_algo(), missing check for ae_algo->ops.
This patch fixes them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are exported, add pointer checking at the beginning
can make them more safe.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.
Fixes: c969c6e7ab ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2 ("net: hns3: Support for dynamically assigning tx buffer to TC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should return -ENOMEM if the kcalloc() fails.
Fixes: d174ea75c9 ("net: hns3: add statistics for PFC frames and MAC control frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.
This patch fixes it by only enabling it when first initialzing.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is resetting, it can't communicate to PF with mailbox msg.
This patch adds reset state checking before sending keep alive msg
to PF.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hclge_init_umv_space() failed in the hclge_init_ae_dev(),
we should undo all the operation which has been done successfully,
the last success operation maybe hclge_mac_mdio_config(), so if
hclge_init_umv_space() failed, we also need to undo it.
Fixes: 288475b2ad01 ("{topost} net: hns3: refine umv space allocation")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rss result is more uniform when use recommended hash key from
microsoft, instead of the one generated by netdev_rss_key_fill().
Also using hash algorithm "xor" is better than "toeplitz".
This patch modifies the default hash key and hash algorithm.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is unloading, if a global reset occurs,
unmap_ring_from_vector() in the hns3_nic_uninit_vector_data() will
fail, and hns3_nic_uninit_vector_data() just return. There may be
some netif_napi_del() not be done.
Since hardware will unmap all ring while resetting, so
hns3_nic_uninit_vector_data() should ignore this error, and do the
rest uninitialization.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF shares the same TC config as PF, the business
running on PF and VF must have samiliar module.
For simplicity, we are not considering VF sharing the same tc
configuration as PF use case, so this patch removes the support
of TC configuration from VF and forcing VF to just use single
TC.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_register_ae_dev() may fail, and it should return a error code
to its caller, so change hnae3_register_ae_dev() return type to int.
Also, when hnae3_register_ae_dev() return error, hns3_probe() should
do some error handling and return the error code.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_close() stop the netdev and the service base on the netdev
will stop. But ndev->netdev_ops->ndo_stop() may only stop HW
and stack queue, the service base on the netdev can still work.
Fixes: 5668abda09 ("net: hns3: add support for set_ringparam")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the .get_regs_len and .get_regs were missed
assigned. This patch fixes it.
Fixes: 1600c3e5f2 ("net: hns3: Support "ethtool -d" for HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Union l3_hdr_info and l4_hdr_info have already been defined in
the hns3_enet.h, so it is unnecessary to define them elsewhere.
This patch removes the redundant definition, and reuses the one
defined in the hns3_enet.h.
Signed-off-by: liyongxin <liyongxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.
Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217
Fixes: 48189d6aaf ("net: hns: enet specifies a reference to dsaf")
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF can receive packets of other functions when in promisc
mode. It's not safe, so don't allow VF to enable promisc
mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initialization for nic state, sets flag
HNS3_NIC_STATE_DOWN when initialize, clears it before
vectors and napi being enabled in the hns3_nic_net_up(),
and sets it back in the error handler.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single transmit packet can span up to 8 descriptors according
to the HW limit. If a skb has more than 8 frags, driver uses
skb_copy to get a new skb which has less frags.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_setup_tc in enet is for updating TC configuration to
stack, and hclge_setup_tc in hclge_dcb is mainly for setting the
configuration to hardware.
This patch removes the hns3_nic_set_real_num_queue from
hns3_setup_tc in enet, and call hclge_client_setup_tc to update
TC configuration to stack with netdev down, because the netdev
down operation is done in hclge_dcb now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After doing down/uninit/init/up in hclge_dcb, it is not necessary
to call dcb_ops->map_update in enet, so hclge_map_update can be
called directly in hclge_dcb.
This is for preparing to call hns3_nic_set_real_num_queue with
netdev down when user changes mqprio configuration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user changes the mqprio configuration, enet need to be
uninited and inited besides down'ed and up'ed, because the queue
num may change when the TC num changes.
Also, it is more suitable to do the down/unint/init/up operation
in hclge module using hclge_notify_client, because this config
change may affect PF and its VF.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setting the serdes loopback, you need to determine
the status of the MAC negotiation. If a status exception
is obtained after 200ms, a timeout error is returned.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, vlan filter is always bypassed when enable
broadcast promisc mode. In this case, broadcast packets with
any vlan id can be accpeted. We should disable broadcast promisc
mode until user want enable it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current code, it always return 0, even loopback mode setting failed.
It's incorrect. This patch fixes return value handle for loopback test.
Fixes: 0f29fc23b2 ("net: hns3: Fix for loopback selftest failed problem")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclge_ieee_setets returns error directly when there is
error, which may cause netdev not up problem.
This patch adds some error handling when setting ETS configuration
fails.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unload hns3 driver, we should clear the pci private data.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet statistics for netdev should not include the packets dropped
by hardware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFC enabling is based on user priority, currently it is
based on TC, which may cause PFC not setting correctly when pri
to TC mapping is not one to one relation.
This patch adds pfc_en in tm_info to fix it.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old firmware version, statistics acquisition of
PFC frames and MAC control frames is not supported.
Add command retrieves statistics for PFC frames and
MAC control frames from the firmware.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the TC weight in SSU module according to
info in tm_info.
Also, zero weight of TC weight in SSU ETS module means enabling
strict priority, so do not allow zero weight when in ETS mode.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GE MAC does not support PFC, when driver is initializing and MAC
is in GE Mode, ignore the fw not supported error, otherwise
initialization will fail.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to firmware error code definition, the error code of 2
means NOT_SUPPORTED, this patch changes it to NOT_SUPPORTED.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Param pending_buf and skb may be not NULL when free ring.
This patch clears them when free ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 849e460776 ("net: hns3: add ethtool_ops.get_channels support for VF")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaper setting does not change currently, when TC num changes,
which may cause shaper parameter not setting problem.
This patch fixes it by setting the shaper parameter when TC num
changes.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rss configuration set by user will be lost when setting
channel.
This patch fixes it by not setting rss configuration to default
if user has configured the rss.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In origin codes, there are some statistics item are got from mac, which
also include the packets statistics of VF. It is unreasonable. This
patch fixes it by counting them in the rx/tx processing flow.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx multicast packets statistic for each ring.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds calling roce callback function when link status
change.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNAE3_INIT_CLIENT interface is also used when changing tc
configuration, vlan/mac hardware table does not need to be restored
when tc configuration changes.
This patch adds a HNAE3_RESTORE_CLIENT interface to restore the
vlan/mac hardware table when resetting.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ETS information is changed, the network device needs to be
re-initialized, otherwise the information such as the receiving queue
will be incorrect.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 482d2e9c1c ("net: hns3: add support to query tqps number")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alloc_tqps field of struct hclge_vport represents the total number
of tqps allocated to the vport. The num_tqps of struct
hnae3_knic_private_info indicates the total number of all enabled tqps,
which needs to be distinguished during use.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool -L option with the combined parameter is for changing the number of
multi-purpose channels of the specified network device. Under the current
scheme, the user configuration information will be lost after the reset or
TC information changed.
This patch fixes this issue. By default, this configuration is set to the
minimum between the number of queues for each enabled TCs and the maximum
number support available in the hardware. When there is a user
configuration, regardless of the reset or TC information change, it should
keep the user's configuration while it is under the hardware limits,
otherwise set to the maximum number support available in the hardware.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC info will be updated in hclge_tm_vport_tc_info_update(),
so hclge_knic_setup() no need to do it again.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of queues for each enabled TC should range from 1 to
the maximum available value, and return directly if the value
is same as the current one.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a common interface to complete the back pressure settings
of all enabled TCs. So other functions directly call this interface
to complete the corresponding operation.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already common interface for network device reinitialization,
so hns3_set_channels() should just call them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter passed to hns3_set_channels() are already the number of
queues per channel of the enabled TC, so it is not need to divide
the number of enabled TCs.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq_init_flag field in struct hns3_enet_ring is unnecessary.
This patch removes it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_reset_notify_init_enet and hns3_reset_notify_uninit_enet are the
reinitialization interface that will be called when the device reset,
the number of TC changed, or the queue length changed. So these two
function should call hns3_get_ring_config() and hns3_put_ring_config()
to allocate and free memory for the ring with the correct number.
Also this patch fixes a double free problem when
hns3_reset_notify_uninit_enet calling hns3_nic_dealloc_vector_data
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 308c6cafde ("net: hns: All ports can not work when insmod hns ko
after rmmod.") add phy_stop in hns_nic_init_phy(), In the branch of "net",
this method is effective, but in the branch of "net-next", it will cause
a WARNING when hns modules loaded, reference to commit 2b3e88ea65 ("net:
phy: improve phy state checking"):
[10.092168] ------------[ cut here ]------------
[10.092171] called from state READY
[10.092189] WARNING: CPU: 4 PID: 1 at ../drivers/net/phy/phy.c:854
phy_stop+0x90/0xb0
[10.092192] Modules linked in:
[10.092197] CPU: 4 PID:1 Comm:swapper/0 Not tainted 4.20.0-rc7-next-20181220 #1
[10.092200] Hardware name: Huawei TaiShan 2280 /D05, BIOS Hisilicon D05 UEFI
16.12 Release 05/15/2017
[10.092202] pstate: 60000005 (nZCv daif -PAN -UAO)
[10.092205] pc : phy_stop+0x90/0xb0
[10.092208] lr : phy_stop+0x90/0xb0
[10.092209] sp : ffff00001159ba90
[10.092212] x29: ffff00001159ba90 x28: 0000000000000007
[10.092215] x27: ffff000011180068 x26: ffff0000110a5620
[10.092218] x25: ffff0000113b6000 x24: ffff842f96dac000
[10.092221] x23: 0000000000000000 x22: 0000000000000000
[10.092223] x21: ffff841fb8425e18 x20: ffff801fb3a56438
[10.092226] x19: ffff801fb3a56000 x18: ffffffffffffffff
[10.092228] x17: 0000000000000000 x16: 0000000000000000
[10.092231] x15: ffff00001122d6c8 x14: ffff00009159b7b7
[10.092234] x13: ffff00001159b7c5 x12: ffff000011245000
[10.092236] x11: 0000000005f5e0ff x10: ffff00001159b750
[10.092239] x9 : 00000000ffffffd0 x8 : 0000000000000465
[10.092242] x7 : ffff0000112457f8 x6 : ffff0000113bd7ce
[10.092245] x5 : 0000000000000000 x4 : 0000000000000000
[10.092247] x3 : 00000000ffffffff x2 : ffff000011245828
[10.092250] x1 : 4b5860bd05871300 x0 : 0000000000000000
[10.092253] Call trace:
[10.092255] phy_stop+0x90/0xb0
[10.092260] hns_nic_init_phy+0xf8/0x110
[10.092262] hns_nic_try_get_ae+0x4c/0x3b0
[10.092264] hns_nic_dev_probe+0x1fc/0x480
[10.092268] platform_drv_probe+0x50/0xa0
[10.092271] really_probe+0x1f4/0x298
[10.092273] driver_probe_device+0x58/0x108
[10.092275] __driver_attach+0xdc/0xe0
[10.092278] bus_for_each_dev+0x74/0xc8
[10.092280] driver_attach+0x20/0x28
[10.092283] bus_add_driver+0x1b8/0x228
[10.092285] driver_register+0x60/0x110
[10.092288] __platform_driver_register+0x40/0x48
[10.092292] hns_nic_dev_driver_init+0x18/0x20
[10.092296] do_one_initcall+0x5c/0x180
[10.092299] kernel_init_freeable+0x198/0x240
[10.092303] kernel_init+0x10/0x108
[10.092306] ret_from_fork+0x10/0x18
[10.092308] ---[ end trace 1396dd0278e397eb ]---
This WARNING occurred because of calling phy_stop before phy_start.
The root cause of the problem in commit '308c6cafde01' is:
Reference to hns_nic_init_phy, the flag phydev->supported is changed after
phy_connect_direct. The flag phydev->supported is 0x6ff when hns modules is
loaded, so will not change Fiber Port power(Reference to marvell.c), which
is power on at default.
Then the flag phydev->supported is changed to 0x6f, so Fiber Port power is
off when removing hns modules.
When hns modules installed again, the flag phydev->supported is default
value 0x6ff, so will not change Fiber Port power(now is off), causing mac
link not up problem.
So the solution is change phy flags before phy_connect_direct.
Fixes: 308c6cafde ("net: hns: All ports can not work when insmod hns ko after rmmod.")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HNAE3_DOWN_CLIENT calling hns3_nic_net_stop(), HNAE3_UP_CLIENT
should call hns3_nic_net_open(), since if the number of queue or
the map of TC has is changed before HHAE3_UP_CLIENT is called,
it will cause problem.
Also the HNS3_NIC_STATE_RESETTING flag needs to be cleared before
hns3_nic_net_open() called, and set it back while hns3_nic_net_open()
failed.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the redundant variable initialization,
as driver will devm_kzalloc to set value to hdev soon.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver gets rss information from the last descriptor of the packet.
When driver handle the rss type, ring->next_to_clean indicates the
first descriptor of next packet.
This patch fix the descriptor index with "ring->next_to_clean - 1".
Fixes: 232fc64b6e ("net: hns3: Add HW RSS hash information to RX skb")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables flow director, all the rules will be disabled. But
when reset happens, it will restore all the rules again. It's not
reasonable. This patch fixes it by add flow director status check before
restore fules.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Fixes: c17852a893 ("net: hns3: Add support for enable/disable flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When add flow director fule for vf, the vf id is used as array
subscript before valid checking, which may cause memory overflow.
Fixes: dd74f815dd ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN operation, the driver will reclaim the memory which has
already used for TX. If the hardware is processing this memory, it will
cause a RCB error to the hardware. According the hardware's description,
the driver should reset the tqp before reclaim the memory during DOWN.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario,
there may be more than 64 cpus online. So the result of min_t(u16,
num_Online_cpus(), tqp_num) may be more than 64. This patch adds check
for the vector number.
Fixes: dd38c72604 ("net: hns3: fix for coalesce configuration lost during reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() in driver may always occupancy processor. If there is only
one cpu in system, the VF driver may initialize fail when insmod
PF and VF driver in the same system. This patch use msleep() to free
cpu when VF wait PF message.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, default tc value is set to the max tc. It's more
reasonable to close tc by changing default tc value to 1. Users can
enable it with lldp tool when they want to use tc.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When triggering nic down, there is a time window between bringing down
the protocol stack and stopping the work task. If the net is up in the
time window, it may bring up the protocol stack again.
This patch fixes it by stop the work task at the beginning of
hns3_nic_net_stop(). To keep symmetrical, start the work task at the
end of hns3_nic_net_open().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.
This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver calls phy_connect_direct and registers hclge_mac_adjust_link
to synchronize mac speed and duplex from phy. It is better to
synchronize mac speed and duplex from phy when phy link up.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our phy does not support 1000M/half, this patch removes 1000M/half from
PHY_SUPPORTED_FEATURES.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
coalesce param updates every 100 napi times, it may update a little
late if ping test after a high rate flow, may over napi poll is called
100 times as ping test sends packets every second.
This patch updates coalesce param every second, instead with every
100 napi times. It can not update the param 100% in time, but the
lag time is very short.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_nic_uninit_vector_data(), the procedure of uninitializing
the tqp_vector's IRQ has not set affinity_notify to NULL and changes
its init flag. This patch fixes it. And for simplificaton, local
variable tqp_vector is used instead of priv->tqp_vector[i].
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, it is unnecessary to get the hardware's default
configuration again, otherwise, the user's configuration will be
overwritten.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() completes successfully, it should update the
last_reset_time, set reset_fail_cnt to 0, and set reset_type of
hnae3_ae_dev to HNAE3_NONE_RESET.
Also when hclgevf_reset() completes successfully, it should update
the last_reset_time, and set reset_type of hnae3_ae_dev to
HNAE3_NONE_RESET.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN, the calling of napi_disable() may not return, since the
napi_complete() in the hns3_nic_common_poll() will never be called when
HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before
checking HNS3_NIC_STETE_DOWN.
Fixes: ff0699e04b ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hclgevf_pci_reset(), it only uninitialize and initialize
the msi, so if the initialization fails, hclgevf_uninit_hdev()
does not need to uninitialize the msi, but needs to uninitialize
the pci, otherwise it will cause pci resource not free.
Fixes: 862d969a3a ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_vector_ring_chain() failed in the
hns3_nic_init_vector_data(), it should do the error handling instead
of return directly.
Also, cur_chain should be freed instead of chain and head->next should
be set to NULL in error handling of hns3_get_vector_ring_chain.
This patch fixes them.
Fixes: 73b907a083 ("net: hns3: bugfix for buffer not free problem during resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li