commit ce722da66d upstream.
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d97c78a190 upstream.
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8w9z
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.2.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit f580170f13 ]
SPLIT_BOUNDARY_DISABLE should be set for DesignWare USB3 DRD Core
of Hisilicon Kirin Soc when dwc3 core act as host.
[mchehab: dropped a dev_dbg() as only traces are now allowwed on this driver]
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Considering there are various special handling for different dwc3
based integrations on SoC, introduce platform data to let glue
layer driver to pass those specific hanldings to dwc3 core driver,
like set_role_post and quirk flags for xhci and dwc3.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit 240acf931cd907e17e90cb46172c2ed3092fabae)
USB role class has 3 state: host, device and none, current dwc3 only
has 2 states: host and device, typec compliance test requires DUT
to stop one specific role USB data when parter removed by set its
to be none, so add none role support by stop current role.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
(cherry picked from commit f6d2550ec1922662c8843e578f36e416ffe36f05)
Per dwc3 databook, if GCTL.SOFITPSYNC is enabled, The DWC_usb3 uses
ref_clk for ITP counter when all the 2.0 ports are suspended.
For this usage, GUCTL.REFCLKPER needs to update to be nano seconds
the period of ref_clk; and GFLADJ.GFLADJ_REFCLK_FLADJ needs to update
to be the frame length adjustment to be applied when SOF/ITP counter is
running on the ref_clk, the value is derived as follows:
FLADJ_REF_CLK_FLADJ=
((125000/ref_clk_period_integer)-(125000/ref_clk_period)) * ref_clk_period where
- the ref_clk_period_integer is the integer value of the ref_clk period
got by truncating the decimal (fractional) value that is programmed in
the GUCTL.REF_CLK_PERIOD field.
- the ref_clk_period is the ref_clk period including the fractional
value.
For imx8mp case, the ref_clk is 24M, so ref_clk_period_integer is 41,
and fladj is 2032.
Review-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
[ Upstream commit d94ea53198 ]
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ba6b09fda ]
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In case system resume by device mode event(e.g, VBUS), runtime resume
will happen before system resume, to avoid doing device mode resume
again when system resume, add a core init flag.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
On some platforms, if the ITP counter clock is from utmi_clk, and
the usb2 suspended firstly, then the ITP clock will miss, to resolve
this, we can use soft ITP sync to make dwc3 core use ref_clk for ITP
counter.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
If we're in the middle of series of chained TRBs and we
receive a short transfer along the way, DWC3 will skip
through all TRBs including the last TRB in the chain, DWC3
will avoid clearing HWO bit and SW has to do it manually.
but currect code can't hit the condition when loop sgs of
request in dwc3_gadget_ep_reclaim_trb_sg() if short packet
received for one chained trb, because it only check the HWO
bit of all trbs and then break if it's 1, so the remain trbs
has no chance to be handled by dwc3_gadget_ep_reclaim_completed_trb(),
this patch adds a flag if received a short packet in a chained
trb, and let dwc3_gadget_ep_reclaim_trb_sg() continue handle
all trbs and give back to function driver.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
DWC3 glue layer driver may need private API to interact with core
driver, here addd a dwc3_priv_data struct and which only has one
API for setting after usb mode set.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
commit da10bcdd6f upstream.
If the END_TRANSFER command hasn't completed yet, then don't send the
START_TRANSFER command. The controller may not be able to start if
that's the case. Some controller revisions depend on this. See
commit 76a638f8ac ("usb: dwc3: gadget: wait for End Transfer to
complete"). Let's only send START_TRANSFER command after the
END_TRANSFER command had completed.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c58d8bfc77 upstream.
While the END_TRANSFER command is sent but not completed, any request
dequeue during this time will cause the driver to issue the END_TRANSFER
command. The driver needs to submit the command only once to stop the
controller from processing further. The controller may take more time to
process the same command multiple times unnecessarily. Let's add a flag
DWC3_EP_END_TRANSFER_PENDING to check for this condition.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 89a9cc4751.
Don't limit DRD for higher IP version.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
This feature is telling how to configure cache type on 4 different
transfer types: Data Read, Desc Read, Data Write and Desc write. For each
transfer type, controller has a 4-bit register field to enable different
cache type. Quoted from DWC3 data book Table 6-5 Cache Type Bit Assignments:
----------------------------------------------------------------
MBUS_TYPE| bit[3] |bit[2] |bit[1] |bit[0]
----------------------------------------------------------------
AHB |Cacheable |Bufferable |Privilegge |Data
AXI3 |Write Allocate|Read Allocate|Cacheable |Bufferable
AXI4 |Allocate Other|Allocate |Modifiable |Bufferable
AXI4 |Other Allocate|Allocate |Modifiable |Bufferable
Native |Same as AXI |Same as AXI |Same as AXI|Same as AXI
----------------------------------------------------------------
Note: The AHB, AXI3, AXI4, and PCIe busses use different names for certain
signals, which have the same meaning:
Bufferable = Posted
Cacheable = Modifiable = Snoop (negation of No Snoop)
In most cases, driver support is not required unless the default values of
registers are not correct *and* DWC3 node has enabled dma-coherent. So far we
have observed USB device detect failure on some Layerscape platforms if this
programming was not applied.
Related struct:
struct dwc3_cache_type {
u8 transfer_type_datard;
u8 transfer_type_descrd;
u8 transfer_type_datawr;
u8 transfer_type_descwr;
};
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
- Advantage of park mode
When only a single Async endpoint is active.
- Behavior of park mode
1. The controller prefetches data/TRBs to do 3 * burst_size worth
of packets.
2. When park mode is disabled there will be some delay between
bursts on the USB. This can be avoided if park mode is enabled
in cases of only one endpoint is active.
3. But this delay is significant only with systems of large
latencies.
4. We have noticed that in cases where a device NAKs often, it
tends to bring down the performance for a single endpoint case.
- Issue on "park mode"
1. LSP (List Processor) goes in and out of park mode irrespective
of the fact that there are more endpoints active. #LSP consider
that there is only one endpoint active.
2. This causes master scheduler and transaction handlers to think
that they are in park mode even though they are not. This is
because request to transaction handlers, generated by HSCH is
in park mode when the request is made
3. This causes a case where the master scheduler calculates wrongly
the number of TRB cache space available.
4. Because of the wrongly calculated number of TRB spaces, the core
fetches more TRBS than there is space for.
5. This causes overwriting the TRB cache area into the TRQ cache
area which is next to the TRB cache area.
6. This causes invalidating an entry in the TRQ
7. This causes transaction handlers to ignore a request in the TRQ
which it should have processed.
8. This causes the main scheduler to hang because it is waiting for
status from transaction handler.
9. This causes host controller to hang.
- Work Around
Disabling park mode for super speed by setting GUCTL1[17] to be 1.
The STAR number is 9001415732, which is target to be released around
May,2020.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will be turned on immediately on related Root Hub
ports. Then, the VBUS is turned off for a little while(15us) when do xhci
reset (conducted by xhci driver) and back to normal finally, we can
observe a negative glitch of related signal happen.
This VBUS glitch might cause some USB devices enumeration fail if kernel
boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
/LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
4GB USB2.0 drives. The fail cases include enumerated as full-speed device
or report wrong device descriptor, etc.
One SW workaround which can fix this is by programing all xhci PORTSC[PP]
to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
(per signal measurement result, it will be too late to do it in
xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
no glitch happen and normal enumeration process has no impact.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
During the USB certification CV9 test, if we report OTG descriptor
to test suite, it will require doing OTG test, but in fact, it does
not support OTG-compliance in dwc3 driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Since the new dwc3 use bulk clks including the suspend clk, so we can
use it to calculate the power down scale value.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The member @lock of dwc3_ep struct is only initialized,
and not used elsewhere, so remove it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.
Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.
Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.
Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.
Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.
This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The macro name DWC3_DCTL_LPM_ERRATA is uninformative and does not do
masking. Remove DWC3_DCTL_LPM_ERRATA_MASK and rename
DWC3_DCTL_LPM_ERRATA to DWC3_DCTL_NYET_THRES with proper masking.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Zhizhikin