Removes the use of bitfields from the ibmveth driver. This results
in slightly smaller object code.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes dead frag processing code from ibmveth. Since NETIF_F_SG was
not set, this code was never executed. Also, since the ibmveth
interface can only handle 6 fragments, core networking code would need
to be modified in order to efficiently enable this support.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool hooks to ibmveth to retrieve driver statistics.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add handlers for get_tso and get_ufo to prevent errors being printed
by ethtool.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the appropriate ethtool hooks to allow for enabling/disabling
of hypervisor assisted checksum offload for TCP.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patchset enables TCP checksum offload support for IPV4
on ibmveth. This completely eliminates the generation and checking of
the checksum for packets that are completely virtual and never
touch a physical network. A simple TCP_STREAM netperf run on
a virtual network with maximum mtu set yielded a ~30% increase
in throughput. This feature is enabled by default on systems that
support it, but can be disabled with a module option.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually, D-Link modified the VendorID/ProductID of the TC902x.
The TC902x is the original chipset.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add suspend/resume support to the uli526x network driver (tested on x86_64,
with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 40').
This patch is based on the suspend/resume code in the tg3 driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add suspend and resume capability to the driver.
Tested both to ram and to disk on x86_64 platform.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this implements support for USB autosuspend in the asix USB ethernet
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper':
drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real':
drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kmalloc() and friends return void*, no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for 802.11g bitrates when starting adhoc
networks, not just 802.11b bitrates.
Signed-off-by: Brajesh Dave <brajeshd@marvell.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch strips away possible mess in regioncode (eg. on my card - 88W8305
chipset - I get 0x3031 instead of expected 0x0031 and as a result the driver
defaults to USA region which is obviously incorrect). Following patch fixes
the issue.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that errors reported by the hardware layer is properly
handled. Otherwise commands tend to get stuck in limbo.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensures that any platform specific code that might live in libertas_reset_device
(for example, OLPC tells the EC to do a GPIO-toggled reset of the wireless
from libertas_reset_device) isn't called. Could be handled better by
interface-specific callbacks and a flag for "other hardware reset".
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure. It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware. It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.
Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL. All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Nathen Meyers
FCC ID: SI5WUB221Z
zd1211b chip 0586:340a v4810 high 00-13-49 AL2230_RF pa0 ----S
Despite the product name, I'm pretty sure this isn't a MIMO device. It
appears just to be a normal ZD1211B and we have never heard of these
devices having more than 1 RF. I guess they named this product this way
to make it appear that it fits in with the rest of their XtremeMIMO
product range.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Daniel Drake, the zd1211rw driver used several
different rate values and names throughout the driver. He has
written a patch to change it and tweaked it after some pretty wild
ideas from my side. But the discussion helped me to understand the
problem better and I think I have nailed it down with this patch.
A zd-rate will consist from now on of a four-bit "pure" rate value
and a modulation type flag as used in the ZD1211 control set used
for packet transmission. This is consistent with the usage in the
zd_rates table. If possible these zd-rates should be used in the
code.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Giuseppe Lippolis
zd1211b chip 0cde:001a v4810 high 00-60-b3 AL2230_RF pa0 g--NS
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While developing the driver we added a lot of debug messages for
setting hardware registers. These messages make the reading of the
log files difficult and are of no use anymore. This patch removes
those messages in zd_chip.c.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes some residual dead code left over from removing the
"flip" receive mode. This patch doesn't change the generated output
at all, since gcc already realized it was dead.
This resolves the "regression" reported by Adrian.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
Replacing kmalloc with kzalloc and cleaning up memset in
drivers/net/tokenring/3c359.c
Signed-off-by: Surya Prabhakar <surya.prabhakar@wipro.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the MAC workaround to deal with switches that do not
honor pause frames.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch covers something like this:
dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));
The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
drivers/net/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
-Fixed Link LED issue when MSI-X is enabled.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Calling store_xmsi_data to store the MSI-X datas during initialization
in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Making MSIX as default intr_type
- Driver will test MSI-X by issuing test MSI-X vector and if fails it will
fallback to INTA
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* (main change) tab-align hardware register value enums, and hw struct
* MMIO_FLUSH_AUDIT_COMPLETE has been defined to 1 for a while. Remove
the code activated when it is set to zero.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing accesses to dev->priv to netdev_priv(dev). The replacment
is safe when netdev_priv is used to access a private structure that is
right next to the net_device structure in memory.
Cf http://groups.google.com/group/comp.os.linux.development.system/browse_thread/thread/de19321bcd94dbb8/0d74a4adcd6177bd
This is the case when the net_device structure was allocated with
a call to alloc_netdev or one of its derivative.
Here is an excerpt of the semantic patch that performs the transformation
@ rule1 @
type T;
struct net_device *dev;
@@
dev =
(
alloc_netdev
|
alloc_etherdev
|
alloc_trdev
)
(sizeof(T), ...)
@ rule1bis @
struct net_device *dev;
expression E;
@@
dev->priv = E
@ rule2 depends on rule1 && !rule1bis @
struct net_device *dev;
type rule1.T;
@@
- (T*) dev->priv
+ netdev_priv(dev)
PS: I have performed the same transformation on the whole kernel
and it affects around 70 files, most of them in drivers/net/.
Should I split my patch for each subnet directories ? (wireless/, wan/, etc)
Thanks to Thomas Surrel for helping me refining my semantic patch.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
3c359.c | 58 +++++++++++++++++++++++++++++-----------------------------
ibmtr.c | 38 +++++++++++++++++++-------------------
lanstreamer.c | 32 ++++++++++++++++----------------
madgemc.c | 4 ++--
olympic.c | 36 ++++++++++++++++++------------------
tmspci.c | 4 ++--
6 files changed, 86 insertions(+), 86 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver has not compiled in anything except PCI support for many
years (see drivers/net/skfp/Makefile). This driver is also unmaintained
for many years, so arguments for keeping the cross-OS, cross-bus (ISA,
EISA, MCA) code do not exist.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A few fields being converted to the wrong sized type, and a few missed
endian conversions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Describe the association response status code the firmware
returns, based on mail to libertas-dev from Ronak.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
