The hardware requires the HDSR and VDSR registers to be set to 1 or
higher. This translates to a minimum combined horizontal sync and back
porch of 20 pixels and a minimum vertical back porch of 3 lines. Reject
modes that fail those requirements.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The rcar-du driver supports probe deferral for external clocks, but
implements it badly by checking the wrong pointer due to a bad copy and
paste. Fix it.
While at it, reject invalid clocks outright for DU channels that have a
display PLL, as the external clock is mandatory in that case. This
avoids a WARN_ON() at runtime.
Fixes: 1b30dbde85 ("drm: rcar-du: Add support for external pixel clock")
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
We return 0 unconditionally in 'rcar_du_crtc_set_crc_source()'.
However, 'ret' is set to some error codes if some function calls fail.
Return 'ret' instead to propagate the error code.
Fixes: 47a52d024e ("media: drm: rcar-du: Add support for CRC computation")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fix the misspelled 'belance' in a comment.
Reported-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The official way to stop the display is to clear the display enable
(DEN) bit in the DSYSR register, but that operates at a group level and
affects the two channels in the group. To disable channels selectively,
the driver uses TV sync mode that stops display operation on the channel
and turns output signals into inputs.
While TV sync mode is available in all DU models currently supported,
the D3 and E3 DUs don't support it. We will thus need to find an
alternative way to turn channels off.
In the meantime, condition the switch to TV sync mode to the
availability of the feature, to avoid writing an invalid value to the
DSYSR register. When the feature is unavailable the display output will
turn blank as all planes are disabled when stopping the CRTC.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
DSYSR is a DU channel register that also contains group fields. It is
thus written to by both the group and CRTC code, using read-update-write
sequences. As the register isn't initialized explicitly at startup time,
this can lead to invalid or otherwise unexpected values being written to
some of the fields if they have been modified by the firmware or just
not reset properly.
To fix this we can write a fully known value to the DSYSR register when
turning a channel's functional clock on. However, the mix of group and
channel fields complicate this. A simpler solution is to cache the
register and initialize the cached value to the desired hardware
defaults.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
On selected SoCs, the DU can use the clock output by the LVDS encoder
PLL as its input dot clock. This feature is optional, but on the D3 and
E3 SoC it is often the only way to obtain a precise dot clock frequency,
as the other available clocks (CPG-generated clock and external clock)
usually have fixed rates.
Add a DU model information field to describe which DU channels can use
the LVDS PLL output clock as their input clock, and configure clock
routing accordingly.
This feature is available on H2, M2-W, M2-N, D3 and E3 SoCs, with D3 and
E3 being the primary targets. It is left disabled in this commit, and
will be enabled per-SoC after careful testing.
At the hardware level, clock routing is configured at runtime in two
steps, first selecting an internal dot clock between the LVDS PLL clock
and the external DOTCLKIN clock, and then selecting between the internal
dot clock and the CPG-generated clock. The first part requires stopping
the whole DU group in order for the change to take effect, thus causing
flickering on the screen. For this reason we currently hardcode the
clock source to the LVDS PLL clock if available, and allow flicker-free
selection of the external DOTCLKIN clock or CPG-generated clock
otherwise. A more dynamic clock selection process can be implemented
later if the need arises.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
The rcar_du_crtc_get() function is always immediately followed by a call
to rcar_du_crtc_setup(). Call the later from the former to simplify the
code, and add a comment to explain how the get and put calls are
balanced.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
The ESCR and OTAR registers exist in each DU channel, but at different
offsets for odd and even channels. This led to usage of the group
register access API to write them, with offsets macros named ESCR/OTAR
and ESCR2/OTAR2 for the first and second ESCR/OTAR register in the group
respectively.
The names are confusing as it suggests that the ESCR/OTAR registers for
DU0 and DU2 are taken into account, especially with writes performed to
the group register access API.
Rename the offsets to ESCR/OTAR02 and ESCR/OTAR13, and use the CRTC
register access API to clarify the code. The offsets values are updated
accordingly.
Cosmetic patch, no functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Squashed ESCR and OTAR changes in a single commit]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Document and re-name the 'dpll_ch' field to a more precise 'dpll_mask' for
consistency with the 'channels_mask' field defined in 'struct
rcar_du_device_info'.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
DU channels not equipped with a DPLL use an SoC internal (provided by
the CPG) or external clock source combined with a DU internal divider to
generate the desired output dot clock frequency.
The current clock selection procedure does not fully exploit the ability
of external clock sources to generate the exact dot clock frequency by
themselves, but relies instead on tuning the internal DU clock divider
only, resulting in a less precise clock generation process.
When possible, and desirable, ask the external clock source for the
exact output dot clock frequency, and select the clock source that
produces the frequency closest to the desired output dot clock.
This patch specifically targets platforms (like Salvator-X[S] and ULCBs)
where the DU's input dotclock.in is generated by the versaclock VC5
clock source, which is capable of generating the exact rate the DU needs
as pixel clock output.
This patch fixes higher resolution modes which requires an high pixel
clock output currently not working on non-HDMI DU channel (such as
1920x1080@60Hz on the VGA output).
Fixes: 1b30dbde85 ("drm: rcar-du: Add support for external pixel clock")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
[Factor out code to a helper function]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
The DU channels that have a display PLL (DPLL) can only use external
clock sources, and don't have an internal clock divider (with the
exception of H3 ES1.x where the post-divider is present and needs to be
used as a workaround for a DPLL silicon issue).
Rework the clock configuration to take this into account, avoiding
selection of non-existing clock sources or usage of a missing
post-divider.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Upcoming implementations of the R-Car DU have removed support for
interlaced display pipelines. Provide a means to determine this based on
the feature flags of the hardware configuration structs.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Use the newly exposed VSP1 interface to enable interlaced frame support
through the VSP1 LIF pipelines.
The DSMR register is updated to set the ODEV flag on interlaced
pipelines, thus defining an interlaced stream as having the ODD field
located in the second half (BOTTOM) of the frame buffer.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Kconfig doesn't have license line, thus, it is GPL-2.0 as default.
rcar_du_regs.h, rcar_lvds_regs.h are GPL-2.0,
and all other files are GPL-2.0+ as original license.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch make changes to allocate crc-entries buffer before
enabling CRC generation.
It moves all the failure check early in the function before setting
the source or memory allocation.
Now set_crc_source takes only two variable inputs, values_cnt we
already gets as part of verify_crc_source.
Changes since V1:
- refactor code to use single spin lock
Changes since V2:
- rebase
Changes since V3:
- rebase on top of VKMS driver
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Leo Li <sunpeng.li@amd.com> (V2)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (V3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180821083858.26275-3-mahesh1.kumar@intel.com
This patch implements get_crc_sources callback, which returns list of
all the crc sources supported by driver in current platform.
Changes Since V1:
- move sources list per-crtc
- init sources-list only for gen3
Changes Since V2:
- Adopt to driver style
- Address other review comments from Laurent Pinchart
Changes Since V3/4/5: (Laurent Pinchart review)
- s/rcar_du_crtc_crc_sources_list_init/rcar_du_crtc_crc_init
- s/rcar_du_crtc_crc_sources_list_uninit/rcar_du_crtc_crc_cleanup
- other cleanup
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180808152630.6563-1-mahesh1.kumar@intel.com
-----BEGIN PGP SIGNATURE-----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=r/WP
-----END PGP SIGNATURE-----
Merge tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove of atomisp driver from staging, as nobody would have time to
dedicate huge efforts to fix all the problems there. Also, we have a
feeling that the driver may not even run the way it is.
- move Zoran driver to staging, in order to be either fixed to use VB2
and the proper media kAPIs or to be removed
- remove videobuf-dvb driver, with is unused for a while
- some V4L2 documentation fixes/improvements
- new sensor drivers: imx258 and ov7251
- a new driver was added to allow using I2C transparent drivers
- several improvements at the ddbridge driver
- several improvements at the ISDB pt1 driver, making it more coherent
with the DVB framework
- added a new platform driver for MIPI CSI-2 RX: cadence
- now, all media drivers can be compiled on x86 with COMPILE_TEST
- almost all media drivers now build on non-x86 architectures with
COMPILE_TEST
- lots of other random stuff: cleanups, support for new board models,
bug fixes, etc
* tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
media: omap2: fix compile-testing with FB_OMAP2=m
media: media/radio/Kconfig: add back RADIO_ISA
media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl()
media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
media: arch: sh: migor: Fix TW9910 PDN gpio
media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure
media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG
media: marvel-ccic: allow ccic and mmp drivers to coexist
media: uvcvideo: Prevent setting unavailable flags
media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges
media: dvb-frontends/stv0910: make TS speed configurable
media: ddbridge/mci: add identifiers to function definition arguments
media: ddbridge/mci: protect against out-of-bounds array access in stop()
media: rc: ensure input/lirc device can be opened after register
media: rc: nuvoton: Keep device enabled during reg init
media: rc: nuvoton: Keep track of users on CIR enable/disable
media: rc: nuvoton: Tweak the interrupt enabling dance
media: uvcvideo: Support realtek's UVC 1.5 device
media: uvcvideo: Fix driver reference counting
media: gspca_zc3xx: Enable short exposure times for OV7648
...
Implement CRC computation configuration and reporting through the DRM
debugfs-based CRC API. The CRC source can be configured to any input
plane or the pipeline output.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DU CRTC driver does not support distinguishing between a hardware
index, and a software (CRTC) index in the event that a DU channel might
not be populated by the hardware.
Support this by adapting the rcar_du_device_info structure to store a
bitmask of available channels rather than a count of CRTCs. The count
can then be obtained by determining the hamming weight of the bitmask.
This allows the rcar_du_crtc_create() function to distinguish between
both index types, and non-populated DU channels will be skipped without
leaving a gap in the software CRTC indexes.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
In general, PLL has VCO (= Voltage controlled oscillator),
one of the very important electronic feature called as "jitter"
is related to this VCO.
In academic generalism, VCO should be maximum to be more small jitter.
In high frequency clock, jitter will be large impact.
Thus, selecting Hi VCO is general theory.
fin fvco fout fclkout
in --> [1/M] --> |PD| -> [LPF] -> [VCO] -> [1/P] -+-> [1/FDPLL] -> out
+-> | | |
| |
+-----------------[1/N]<-------------+
fclkout = fvco / P / FDPLL -- (1)
In PD, it will loop until fin/M = fvco/P/N
fvco = fin * P * N / M -- (2)
(1) + (2) indicates
fclkout = fin * N / M / FDPLL
In this device, N = (n + 1), M = (m + 1), P = 2, FDPLL = (fdpll + 1).
fclkout = fin * (n + 1) / (m + 1) / (fdpll + 1)
This is the datasheet formula.
One note here is that it should be 2kHz < fvco < 4096MHz
To be smaller jitter, fvco should be maximum,
in other words, N as large as possible, M as small as possible driver
should select. Here, basically M=1.
This patch do it.
Reported-by: HIROSHI INOSE <hiroshi.inose.rb@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Small clarifications in comments, renamed finnm to fout]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
It is difficult to understand its scale if number has many 0s.
This patch uses "* 1000" to avoid it in rcar_du_dpll_divider().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Unlike the KMS API, the hardware doesn't support planes exceeding the
screen boundaries or planes being located fully off-screen. We need to
clip plane coordinates to support the use case.
Fortunately the DRM core offers a drm_atomic_helper_check_plane_state()
helper that validates the scaling factor and clips the plane
coordinates. Use it to implement the plane atomic check and use the
clipped source and destination rectangles from the plane state instead
of the unclipped source and CRTC coordinates to configure the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
An early implementation of suspend-resume helpers are available in the
CRTC module, however they are unused and no longer needed.
With suspend and resume handled by the core DRM atomic helpers, we can
remove the unused functions.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.
To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.
As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.
With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.
Fixes: d503a43ac0 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When stopping the CRTC the driver must disable all planes and wait for
the change to take effect at the next vblank. Merely calling
drm_crtc_wait_one_vblank() is not enough, as the function doesn't
include any mechanism to handle the race with vblank interrupts.
Replace the drm_crtc_wait_one_vblank() call with a manual mechanism that
handles the vblank interrupt race.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
When implementing support for interlaced modes, the driver switched from
reporting vblank events on the vertical blanking (VBK) interrupt to the
frame end interrupt (FRM). This incorrectly divided the reported refresh
rate by two. Fix it by moving back to the VBK interrupt.
Fixes: 906eff7fca ("drm: rcar-du: Implement support for interlaced modes")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Commit 52055bafa1 ("drm: rcar-du: Move plane commit code from CRTC
start to CRTC resume") changed the order of the plane commit and CRTC
enable operations to accommodate the runtime PM requirements. However,
this introduced corruption in the first displayed frame, as the CRTC is
now enabled without any plane configured. On Gen2 hardware the first
frame will be black and likely unnoticed, but on Gen3 hardware we end up
starting the display before the VSP compositor, which is more
noticeable.
To fix this, revert the order of the commit operations back, and handle
runtime PM requirements in the CRTC .atomic_begin() and .atomic_enable()
helper operation handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The H3 ES1.x exhibits dot clock duty cycle stability issues. We can work
around them by configuring the DPLL to twice the desired frequency,
coupled with a /2 post-divider. This isn't needed on other SoCs and
breaks HDMI output on M3-W for a currently unknown reason, so restrict
the workaround to H3 ES1.x.
From an implementation point of view, move work around handling outside
of the rcar_du_dpll_divider() function by requesting a x2 DPLL output
frequency explicitly. The existing post-divider calculation mechanism
will then take care of dividing the clock by two automatically.
While at it, print a more useful debugging message to ease debugging
clock rate issues.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
On R-Car H3 ES2.0, DU channels 0 and 3 are served by two separate
pipelines from the same VSP. Support this in the DU driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
To avoid mixing comment styles when new comments complying with the
kernel coding style are introduced, fix all multiline comments in one
go.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
Currently we process page flip events on every display interrupt,
however this does not take into consideration the processing time needed
by the VSP1 utilised in the pipeline.
Register a callback with the VSP driver to obtain completion events, and
track them so that we only perform page flips when the full display
pipeline has completed for the frame.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The page flip event is armed in the atomic begin handler, creating a
race condition with the frame end interrupt that could send the event
before the atomic operation actually completes. To avoid that, arm the
event in the atomic flush handler after queuing the page flip.
This change doesn't fully close the race window, as the frame end
interrupt could be generated before the page flip is committed to
hardware but only handled after the event is armed. However, the race
window is now much smaller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The implementation hardcodes a workaround for the H3 ES1.x SoC
regardless of the SoC revision, as the workaround can be safely applied
on all devices in the Gen3 family without any side effect.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The atomic commit helper requires drivers to clear the event pointer
stored in the CRTC state when the event is handled. In preparation to
using the helper, fix the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver currently handles vblank events only when updating planes on
a CRTC. The atomic update API however allows requesting an event when
disabling a CRTC. This currently leads to event objects being leaked in
the kernel and to events not being sent out. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-17-git-send-email-shawnguo@kernel.org
The VSL and HSL bits in the DSMR register set the corresponding
horizontal and vertical sync signal polarity to active high. The code
got it the wrong way around, fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
There is a bug in the setting of the DES (Display Enable Signal)
register. This current setting occurs 1 dot left shift. The DES
register should be set minus one value about the specifying value
with H/W specification. This patch corrects it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
version 6:
rebased patch on top rcar-du changes for zpos
version 4:
fix null pointer issue while setting zpos in plane reset function
This patch replaces zpos property handling custom code in rcar DRM
driver with calls to generic DRM code.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Document the R8A7795-specific DT bindings and support them in the
driver. The HDMI and LVDS outputs are currently not supported.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DE signal is currently configured to be identical to the DISP
signal and is used for the same purpose. To make it clearer that the
DISP pin outputs the DISP signal, select it explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The Gen3 R8A7795 DU has 4 CRTCs, support them all.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
On R-Car Gen3 SoCs the DU lost its ability to access memory directly and
needs to work in conjunction with the VSP to do so. This commit handles
the VSP internally to hide it from the user.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
