When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Dmesg log is as following:
amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device.
amdgpu: cp queue pipe 4 queue 0 preemption failed
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
global noretry setting is cached to gmc.noretry
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to correct the sensor value of power for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* dma-buf: Include <linux/vmalloc.h> for building on MIPS
* komeda: Fix order of operation in commit tail; Fix NULL-pointer and
out-of-bounds access; Cleanups
* ttm: Fix an unused-function warning
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl/iRSAACgkQaA3BHVML
eiMrsQf/dlHwJykbsGbkE/lG8qgrnz4jFKkei+DnZjqNaAwvgbz9s1YvaMYIIdsE
wvYnBSTvdvhYzde08+E0Q4JLCvHh/0aHWqkZR3dGd22tAgNxGfslBITu07EyI+k8
Agy4AeBbYJUwYcfRAHqwDuKCDQ28/FXcBpLajSF9K9oG6et2GgftshuIwWij2xNR
kNQTddCsXdXXbFDK/N3X/Inb+WSbRU0GWDTMTUPC31rMXX6kIKASQmVvCQ8h6a5F
N9EqjUmGf7XGjdqWEkSM34HpCUv5c5N2MWc4OAiSaP3Q3QVJyp3RHg8zLOpeSIsy
hVAj+8SN8UrI+Fz0Tx+SFdU72t0eVA==
=hlDA
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2020-12-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* dma-buf: Include <linux/vmalloc.h> for building on MIPS
* komeda: Fix order of operation in commit tail; Fix NULL-pointer and
out-of-bounds access; Cleanups
* ttm: Fix an unused-function warning
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/X+JFYlW1SEZa6ShA@linux-uq9g
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739
Fixes: 65bf2cf95d ("drm/amdgpu: utilize subconnector property for DP through atombios")
Tested-By: Kris Karas <bugs-a17@moonlit-rail.com>
Cc: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
This can suppress the annoying but unharmful prompts.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new_crtc_state is already dereferenced earlier in the function
[How]
Remove the check
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need driver to pass values of backlight ramp start and ramp reduction so
that intensity can be ramped down appropriately.
[How]
Using abm_parameters structure to get these values from driver.
Signed-off-by: Rizvi <syerizvi@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some MST display may not report the internal panel to DEVICE_COUNT,
that makes the check condition always failed.
[how]
To update this condition with the reported device count + 1
(because the immediate repeater's internal panel is possibly
not included in DEVICE_COUNT)
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
handler is supposedly passed in as a function pointer;
however, the entire struct amdgpu_dm_irq_handler_data
gets from the list is used to check match.
[how]
use the interrupt_handler within amdgpu_dm_irq_handler_data
for checking match.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GUI_IDLE interrupts controlled by CP_INT_CNTL_RING0
are only applicable to me0 pipe0.
For ASICs that have gfx pipe removed, don't toggle
those bits.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The number of crtc should be 0 for ASICs that don't
have display engine. Remove the unnecessary asic type
check then.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check number of gfx ring, rather than asic type,
before cp gfx engine initialization so driver just
need to make sure number of gfx ring is initialized
correctly in gfx early_init phase. No need to add
additional asic type check everywhere when there is
new asic with gfx pipe removed.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KASAN found this problem. find_first_bit() expects to look at a
pointer pointing to a long, but we look at a u32 - this is going to be
an issue with endianness but, KSAN already flags this as out-of-bounds
stack reads. This fixes it by just importing inot a local long.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218150812.68195-1-carsten.haitzler@foss.arm.com
komeda_component_get_old_state() technically can return a NULL
pointer. komeda_compiz_set_input() even warns when this happens, but
then proceeeds to use that NULL pointer to compare memory content there
agains the new state to see if it changed. In this case, it's better to
assume that the input changed as there is no old state to compare
against and thus assume the changes happen anyway.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[Applied small spelling fixes and fix suggested by Steven Price]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127110054.133686-1-carsten.haitzler@foss.arm.com
ret is not actually read after this (only written in one case then
returned), so this assign line is useless. This removes that assignment.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127110027.133569-1-carsten.haitzler@foss.arm.com
Komeda HW has no special, program the update to HW is done first,
then flip happens. So correct the sequence to hw_done() first then
flip_done().
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: James Qian Wang <james.qian.wang@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201119013948.2866343-1-james.qian.wang@arm.com
That seems to be unused.
Daniel: Mike reported a warning when booting with qxl, which this
patch fixes:
[ 1.815561] WARNING: CPU: 7 PID: 355 at drivers/gpu/drm/ttm/ttm_pool.c:365 ttm_pool_alloc+0x41b/0x540 [ttm]
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Mike Galbraith <efault@gmx.de>
References: https://lore.kernel.org/lkml/7cb43d5b-4e6a-defc-1ab6-5f713ad5a963@amd.com/
Reviewed-by: David Airlie <airlied@redhat.com>
[davnet: bring commit message up to par.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218134243.110884-1-christian.koenig@amd.com
As per the radeon/amdgpu fix don't use multihop if hw moves
aren't enabled.
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Fixes: 0c8c0659d7 ("drm/nouveau/ttm: use multihop")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201217200943.30511-1-airlied@gmail.com
Fix TGL REVID macros to fetch correct display/gt stepping based
on SOC rev id from INTEL_REVID() macro. Previously, we were just
returning the first element of the revid array instead of using
the correct index based on SOC rev id.
Fixes: c33298cb34 ("drm/i915/tgl: Fix stepping WA matching")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203072359.156682-1-aditya.swarup@intel.com
(cherry picked from commit 83dbd74f82)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We now use ilk_hpd_irq_setup for all GMCH platforms that do not have
hotplug. These are early gen3 and gen2 devices that now explode on boot
as they try to access non-existent registers.
Fixes: 794d61a190 ("drm/i915: re-order if/else ladder for hpd_irq_setup")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127145748.29491-1-chris@chris-wilson.co.uk
(cherry picked from commit e5346a1ff3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There is no reserveration so set the size to 0. Fixes
a regression on SR-IOV.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only pmfw version behind v4.63.23.00 could support this message.
Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX10 CP firmware expects PCIe atomics support. Don't enumerate GFX10
devices on platforms (PCIe v2) that don't support PCIe atomics.
Currently, some of the applications like clinfo soft hangs on platforms
without PCIe atomics support.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add documentation for crc window.
Fixes: c920888c60 ("drm/amd/display: Expose new CRC window property")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
This makes it easier to debug what block is causing the fault, same as
sienna_cichlid.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use mode1 reset for dimgrey_cavefish by default.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some old ASICs might not implement/require get_dig_frontend helper; in
this scenario, we can have a NULL pointer exception when we try to call
it inside vbios disable operation. For example, this situation might
happen when using Polaris12 with an eDP panel. This commit avoids this
situation by adding a specific get_dig_frontend implementation for DCEx.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Chiawen Huang <chiawen.huang@amd.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Dennis Li