commit 3d992fd8f4 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb08965622 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove no longer needed samsung thermal properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
The exynos-syscon-restart.dtsi is already included by exynos5.dtsi
(through exynos54xx.dtsi).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c0254 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b0 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This reverts commit 6737b08140.
Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC. The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for the True Random Number Generator found in Samsung Exynos
5250+ SoCs.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for Pseudo Random Number Generator in dts files describing
Exynos5 chips.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
PMU (system-controller@10040000) is used as interrupt-parent for certain
nodes thus it should be marked as interrupt-controller to silence
warnings when building Exynos5410-based DTBs:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (interrupts_property):
Missing interrupt-controller or interrupt-map property in /soc/system-controller@10040000
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (interrupts_property):
Missing #interrupt-cells in interrupt-parent /soc/system-controller@10040000
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for ARM Performance Monitoring Units available in Cortex-A7
and Cortex-A15 CPU cores for Exynos54xx SoCs (5410, 5420 and 5422/5800).
The PMUs interrupts are defined in the common exynos54xx.dtsi device tree,
but the PMUs are enabled and have their interrupt CPU affinity defined
next to each SoC's cpus node.
Tested with perf on Odroid XU4 (Exynos5422):
armv7_cortex_a7 PMU driver: 5 counters available
armv7_cortex_a15 PMU driver: 7 counters available
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Willy Wolff <willy.mh.wolff@gmail.com>
[mszyprow: reordered nodes according to krzk request, fixed typos]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UART modules can use DMA for offloading data transfers and reducing
interrupts, so enable this feature for Exynos5 boards. Tested on
Google ChromeBook Snow (Exynos5250), Odroid XU (Exynos5410) and Odroid
XU3 (Exynos5422) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lyeE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch with DT changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5440
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5260
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos4
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5440
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5260
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5410/exynos542x
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4x12
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4210
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4
Signed-off-by: Olof Johansson <olof@lixom.net>
Recently added audio block of Exynos5410 missed global fixup of GIC
interrupt flags. Interrupt of type IRQ_TYPE_NONE is not allowed for GIC
interrupts so use level high.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This patch adds device nodes for the AUDSS clock controller,
peripheral DMA 0/1 controllers and the Audio Subsystem I2S controller.
These entries are required for sound support on Odroid-XU board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move watchdog and Security SubSystem nodes from exynos5420.dtsi to file
shared with Exynos5410 and configure the clocks on the latter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Add nodes for Thermal Management Unit to exynos5410.dtsi. Use the same
compatible as for Exynos5420 however without second base for TRIMINFO
register and without TMU for GPU.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
On Exynos5410 the SPI interrupt for second USB DWC3 (called DRD: Dual
Role Device) is different - 200 instead of 73.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Configure Exynos5410-specific properties of RTC, I2C and HSI2C nodes.
This still does not enable them on the board level though.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Move USB 3.0 DWC and 2.0 EHCI/OHCI nodes from exynos5420.dtsi to
exynos54xx.dtsi common for entire family. For Exynos542x/5800 this
should not have functional impact but for Exynos5410 this effectively
adds USB support.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
The Exynos5410/542x/5800 are very similar designs. Create a new
DTSI with common nodes to remove DTS duplication. Although currently
only MCT and SysRAM are shared but in future more nodes will be added to
the common file.
The patch should not have functional impact.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Just like other Exynos5 family SoCs, this one has four UARTs. Configure
clocks for UART3 and enable it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The exynos5.dtsi is used for common nodes shared between Exynos5250 and
Exynos542x. Since Exynos5410 is very similar to Exynos5420 it can
include the common file as well to remove duplication and make
everything more consistent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
For consistency lowercase node labels are used.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The CLKOUT (which control is provided by PMU) is necessary for some of
the drivers using this as a clock, e.g. usb3503 USB HUB on Odroid XU
board.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch changes SROM nodes compatible from generic to model specific
to match with binding documentation. Also updating property
"samsung,srom-page-mode" as it is not defined as bool instead of int
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
All Exynos SoCs have the same syscon reboot and poweroff device nodes so
there is no need to duplicate the same on each SoC dtsi and can be moved
to a common dtsi that can be included by all the SoCs dtsi files.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung,com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The chip is smsc9115, connected via SROMc bank 3. Additionally, some GPIO
initialization is required.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
driver. The driver saves and restores SROM registers during suspend to RAM.
DT changes should go in before removal of SROM support from mach-exynos.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MvOQ
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-srom-4.6' into next/dt
Device Tree changes for v4.6 adding the nodes for Exynos SROM controller
driver. The driver saves and restores SROM registers during suspend to RAM.
DT changes should go in before removal of SROM support from mach-exynos.
This machine uses own SoC device tree file, add missing part.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add the required pin configuration support to Exynos5410 using pinctrl
interface.
Signed-off-by: Hakjoo Kim <ruppi.kim@hardkernel.com>
[AF: Rebased, style changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
[k.kozlowski: Move pinctrl nodes into soc node]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds syscon-{reboot, poweroff} nodes to allow the
generic syscon-{reboot, poweroff} driver to reset/poweroff exynos5410 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
Exynos initialization code now relies on obtaining the PMU address,
so prepare a PMU node for Exynos5410.
Fixes: fce9e5bb25 ("ARM: EXYNOS: Add support for mapping PMU base
address via DT")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds alias entries for UART nodes of all SoCs using
samsung-uart compatible UART controllers, so that the dependency on
probe order is removed and deterministic device naming is assured.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's 1.6 GHz for the Cortex-A15.
Avoids warnings like "/cpus/cpu@0 missing clock-frequency property".
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Krzysztof Kozlowski