* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
b43: Fix warning at drivers/mmc/core/core.c:237 in mmc_wait_for_cmd
mac80211: fix failure to check kmalloc return value in key_key_read
libertas: Fix sd8686 firmware reload
ath9k: Fix incorrect access of rate flags in RC
netfilter: xt_socket: Make tproto signed in socket_mt6_v1().
stmmac: enable/disable rx/tx in the core with a single write.
net: atarilance - flags should be unsigned long
netxen: fix kdump
pktgen: Limit how much data we copy onto the stack.
net: Limit socket I/O iovec total length to INT_MAX.
USB: gadget: fix ethernet gadget crash in gether_setup
fib: Fix fib zone and its hash leak on namespace stop
cxgb3: Fix panic in free_tx_desc()
cxgb3: fix crash due to manipulating queues before registration
8390: Don't oops on starting dev queue
dccp ccid-2: Stop polling
dccp: Refine the wait-for-ccid mechanism
dccp: Extend CCID packet dequeueing interface
dccp: Return-value convention of hc_tx_send_packet()
igbvf: fix panic on load
...
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (46 commits)
ftrace/MIPS: Enable C Version of recordmcount
ftrace/MIPS: Add module support for C version of recordmcount
ftrace/MIPS: Add MIPS64 support for C version of recordmcount
MIPS: Make TASK_SIZE reflect proper size for both 32 and 64 bit processes.
MIPS: Allow UserLocal on MIPS_R1 processors
MIPS: Honor L2 bypass bit
MIPS: Add BMIPS CP0 register definitions
MIPS: Add BMIPS processor types to Kconfig
MIPS: Decouple BMIPS CPU support from bcm47xx/bcm63xx SoC code
MIPS: Add support for hardware performance events (mipsxx)
MIPS: Perf-events: Add callchain support
MIPS: add support for hardware performance events (skeleton)
MIPS: add support for software performance events
MIPS: define local_xchg from xchg_local to atomic_long_xchg
MIPS: AR7: Add support for Titan (TNETV10xx) SoC variant
MIPS: AR7: Initialize GPIO earlier
MIPS: Add platform device and Kconfig for Octeon USB EHCI / OHCI
USB: Add EHCI and OHCH glue for OCTEON II SOCs.
MIPS: Octeon: Add register definitions for EHCI / OHCI USB glue logic.
MIPS: Octeon: Apply CN63XXP1 errata workarounds.
...
The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
use the new definitions on twl header for code
consistency.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Crash is triggered by commit e6484930d7 ("net: allocate tx queues in
register_netdevice"), which moved tx netqueue creation into register_netdev.
So now calling netif_stop_queue() before register_netdev causes an oops.
Move netif_stop_queue() after net device registration to fix crash.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbfs_get_inode() is something completely different...
Bogosity introduced by commit 85fe4025c6 ("fs: do not assign default
i_ino in new_inode").
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'vfs' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl: (30 commits)
BKL: remove BKL from freevxfs
BKL: remove BKL from qnx4
autofs4: Only declare function when CONFIG_COMPAT is defined
autofs: Only declare function when CONFIG_COMPAT is defined
ncpfs: Lock socket in ncpfs while setting its callbacks
fs/locks.c: prepare for BKL removal
BKL: Remove BKL from ncpfs
BKL: Remove BKL from OCFS2
BKL: Remove BKL from squashfs
BKL: Remove BKL from jffs2
BKL: Remove BKL from ecryptfs
BKL: Remove BKL from afs
BKL: Remove BKL from USB gadgetfs
BKL: Remove BKL from autofs4
BKL: Remove BKL from isofs
BKL: Remove BKL from fat
BKL: Remove BKL from ext2 filesystem
BKL: Remove BKL from do_new_mount()
BKL: Remove BKL from cgroup
BKL: Remove BKL from NTFS
...
Fix regression introduced by commit
f26788da3b (USB: serial: refactor generic
close) which broke driver close().
This driver uses non-standard semantics for the read urb which makes the
generic close function fail to kill it (the read urb is actually an
interrupt urb and therefore bulk_in size is zero).
Reported-by: Eric Shattow "Eprecocious" <lucent@gmail.com>
Tested-by: Eric Shattow "Eprecocious" <lucent@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In function udc_probe() call put_device() when device_register() fails.
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Acked-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
warning: (USB_MUSB_HDRC_HCD && USB_SUPPORT && USB_MUSB_HDRC &&
(USB_MUSB_HOST || USB_MUSB_OTG) && USB_GADGET_MUSB_HDRC || USB_MUSB_OTG
&& <choice> && USB && USB_GADGET && PM && EXPERIMENTAL) selects USB_OTG
which has unmet direct dependencies (USB_GADGET_OMAP && ARCH_OMAP_OTG &&
USB_OHCI_HCD)
This doesn't seem to happen on 2.6.36-rc8, but still doesn't make sense
to keep this duplicated config that is already defined in usb/core.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When USB was removed, this patch prepares for the next insertion.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the requested device ids to the ftdi_sio driver.
Reported-by: Ewan Bingham <ewan@auc.co.uk>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x has musb interface and uses CPPI4.1 DMA engine.
Current patch supports only PIO mode. DMA support can be
added later once basic CPPI4.1 DMA patch is accepted.
Also added USB_MUSB_AM35X which is required to differentiate musb ips
between OMAP3x and AM35x. This config would be used to for below
purposes,
- Select am35x.c instead of omap2430.c for compilation
at drivers/usb/musb directory. Please note there are
significant differneces in these two files as musb ip
in quite different on AM35x.
Please note that in multi omap configuration only omap2430.c
file will get compiled and we would require to select only
AM35x based board config to compile am35x.c
- Select workaround codes applicable for AM35x musb issues.
one such workaround is for bytewise read issue on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this error when CONFIG_PM is not enabled:
drivers/usb/host/xhci.c:675: error: implicit declaration of function 'usb_root_hub_lost_power'
Wrap xhci_suspend() and xhci_resume() into an ifdef CONFIG_PM, along with
the functions that only they call -- xhci_save_registers() and
xhci_restore_registers().
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few devices (such as the RCA VR5220 voice recorder) are so
non-compliant with the USB spec that they have invalid maxpacket sizes
for endpoint 0. Nevertheless, as long as we can safely use them, we
may as well do so.
This patch (as1432) softens our acceptance criterion by allowing
high-speed devices to have ep0-maxpacket sizes other than 64. A
warning is printed in the system log when this happens, and the
existing error message is clarified.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: James <bjlockie@lockie.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the PCI suspend/resume.
Please refer to xHCI spec for doing the suspend/resume operation.
For S3, CSS/SRS in USBCMD is used to save/restore the internal state.
However, an error maybe occurs while restoring the internal state.
In this case, it means that HC internal state is wrong and HC will be
re-initialized.
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Dong Nguyen <dong.nguyen@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements xHCI bus suspend/resume function hook.
In the patch it goes through all the ports and suspend/resume
the ports if needed.
If any port is in remote wakeup, abort bus suspend as what ehci/ohci do.
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit implements port remote wakeup.
When a port is in U3 state and resume signaling is detected from a device,
the port transitions to the Resume state, and the xHC generates a Port Status
Change Event.
For USB3 port, software write a '0' to the PLS field to complete the resume
signaling. For USB2 port, the resume should be signaling for at least 20ms,
irq handler set a timer for port remote wakeup, and then finishes process in
hub_control GetPortStatus.
Some codes are borrowed from EHCI code.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add software trigger USB device suspend resume function hook.
Do port suspend & resume in terms of xHCI spec.
Port Suspend:
Stop all endpoints via Stop Endpoint Command with Suspend (SP) flag set.
Place individual ports into suspend mode by writing '3' for Port Link State
(PLS) field into PORTSC register. This can only be done when the port is in
Enabled state. When writing, the Port Link State Write Strobe (LWS) bit shall
be set to '1'.
Allocate an xhci_command and stash it in xhci_virt_device to wait completion for
the last Stop Endpoint Command. Use the Suspend bit in TRB to indicate the Stop
Endpoint Command is for port suspend. Based on Sarah's suggestion.
Port Resume:
Write '0' in PLS field, device will transition to running state.
Ring an endpoints' doorbell to restart it.
Ref: USB device remote wake need another patch to implement. For details of
how USB subsystem do power management, please see:
Documentation/usb/power-management.txt
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the system suspends and a host controller's power is lost, the USB
core attempts to revive any USB devices that had the persist_enabled flag
set. For non-SuperSpeed devices, it will disable the port, and then set
the udev->reset_resume flag. This will cause the USB core to reset the
device, verify the device descriptors to make sure it's the same device,
and re-install any non-default configurations or alternate interface
settings.
However, we can't disable SuperSpeed root hub ports because that turns off
SuperSpeed terminations, which will inhibit any devices connecting at USB
3.0 speeds. (Plus external hubs don't allow SuperSpeed ports to be
disabled.)
Because of this logic in hub_activate():
/* We can forget about a "removed" device when there's a
* physical disconnect or the connect status changes.
*/
if (!(portstatus & USB_PORT_STAT_CONNECTION) ||
(portchange & USB_PORT_STAT_C_CONNECTION))
clear_bit(port1, hub->removed_bits);
if (!udev || udev->state == USB_STATE_NOTATTACHED) {
/* Tell khubd to disconnect the device or
* check for a new connection
*/
if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
set_bit(port1, hub->change_bits);
} else if (portstatus & USB_PORT_STAT_ENABLE) {
/* The power session apparently survived the resume.
* If there was an overcurrent or suspend change
* (i.e., remote wakeup request), have khubd
* take care of it.
*/
if (portchange)
set_bit(port1, hub->change_bits);
} else if (udev->persist_enabled) {
udev->reset_resume = 1;
set_bit(port1, hub->change_bits);
} else {
/* The power session is gone; tell khubd */
usb_set_device_state(udev, USB_STATE_NOTATTACHED);
set_bit(port1, hub->change_bits);
}
a SuperSpeed device after a resume with a loss of power will never get the
reset_resume flag set. Instead the core will assume the power session
survived and that the device still has the same address, configuration,
and alternate interface settings. The xHCI host controller will have no
knowledge of the device (since all xhci_virt_devices were destroyed when
power loss was discovered, and xhci_discover_or_reset_device() has not
been called), and all URBs to the device will fail.
If the device driver responds by resetting the device, everything will
continue smoothly. However, if lsusb is used before the device driver
resets the device (or there is no driver), then all lsusb descriptor
fetches will fail.
The quick fix is to pretend the port is disabled in hub_activate(), by
clearing the local variable. But I'm not sure what other parts of the hub
driver need to be changed because they have assumptions about when ports
will be disabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xHCI driver uses hardware assigned device address. This may cause device
address conflict in certain cases.
Use kernel assigned address for devices under xHCI. Store the xHC assigned
address locally in xHCI driver.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Rename xhci_reset_device() to xhci_discover_or_reset_device().
If xhci_discover_or_reset_device() is called to reset a device which does
not exist or does not match the udev, it calls xhci_alloc_dev() to
re-allocate the device.
This would prevent the reset device failure, possibly due to the xHC restore
error during S3/S4 resume.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a pointer to udev in struct xhci_virt_device. When allocate a new
virt_device, make the pointer point to the corresponding udev.
Modify xhci_check_args(), check if virt_dev->udev matches the target udev,
to make sure command is issued to the right device.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some functions changed by 1c98347e61.
However, There was a change mistake of the function (outsw).
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Paul Mundt <lethal@linux-sh.org>
Cc: stable <stable@kernel.org> [.35 & .36]
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend id's table to have ulpi phy names in it.
Report if the known phy is found.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve ulpi phy detection by utilizing the "scratch" register.
Allow unknown ulpi phy work without the need to hard-code the id.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OPN2001 expects write operations to arrive as a vendor-specific command
through the control pipe (instead of using a separate bulk-out pipe).
Signed-off-by: Alon Ziv <alon-git@nolaviz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bulk-read callback had two bugs:
a) The bulk-in packet's leading two zeros were returned (and the two last
bytes truncated)
b) The wrong URB was transmitted for the second (and later) read requests,
causing further reads to return the entire packet (including leading
zeros)
Signed-off-by: Alon Ziv <alon-git@nolaviz.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to set latency timeout at every open.
This also fixes an issue with the read latency being as high as 250ms
(instead of 1ms) for the first read after port probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the iowarrior devices in this case statement support more than 8 bytes
per report, it is possible to write past the end of a kernel heap allocation.
This will probably never be possible, but change the allocation to be more
defensive anyway.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit
214916f2ec (USB: visor: reimplement using
generic framework) which broke initialisation of UX50/TH55 devices that
used re-mapped bulk-out endpoint addresses.
Reported-by: Robert Gadsdon <rgadsdon@bayarea.net>
Tested-by: Robert Gadsdon <rgadsdon@bayarea.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for FTDI USB serial driver ads new VID/PIDs used on various
devices manufactured by Papouch (http://www.papouch.com). These devices
have their own VID/PID, although they're using standard FTDI chip. In
ftdi_sio.c, I also made small cleanup to have declarations for all
Papouch devices together.
Signed-off-by: Daniel Suchy <danny@danysek.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
