Since the i2c driver of Spreadtrum can not be build as one module, thus
it should depend on CONFIG_I2C is build in.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.
This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.
Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c2188 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored as a reference in the quirks
field of an i2c_adapter structure, which is const. Done using
Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored in the algo field of
i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
count data1 data2 data3 data4
0x04 0xde 0xad 0xbe 0xef
That's what we want to return in data->block to the next level.
Instead we were actually prefixing that with desc->rxbytes:
bad
count count data1 data2 data3 data4
0x05 0x04 0xde 0xad 0xbe 0xef
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The structure cht_wc_i2c_adap_driver is local to the source
and does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'cht_wc_i2c_adap_driver' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In addition to the base, low and high clock configuration, the AC timing
register #1 on the AST2400 houses fields controlling:
1. tBUF: Minimum delay between Stop and Start conditions
2. tHDSTA: Hold time for the Start condition
3. tACST: Setup time for Start and Stop conditions, and hold time for the
Repeated Start condition
These values are defined in hardware on the AST2500 and therefore don't
need to be set.
aspeed_i2c_init_clk() was performing a direct write of the generated
clock values rather than a read/mask/modify/update sequence to retain
tBUF, tHDSTA and tACST, and therefore cleared the tBUF, tHDSTA and tACST
fields on the AST2400. This resulted in a delay/setup/hold time of 1
base clock, which in some configurations is not enough for some devices
(e.g. the MAX31785 fan controller, with an APB of 48MHz and a desired
bus speed of 100kHz).
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There seems to be no need for separate ones since all users include both
files anyhow. Merge them because include/linux/i2c is to be deprecated.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Cherry Trail Whiskey Cove PMIC's IRQ line is attached to one of
the GPIOs of the Cherry Trail SoC. The CHT GPIO controller sometimes
fails to deliver IRQs (seen when there is an IRQ storm on another pin).
This commit works around this by reducing the long timeout which was
a poor attempt to workaround this from 3s to 30ms and after that
manually checking the status register for transfer completion by
calling the threaded IRQ handler directly.
This is safe todo as the entire threaded IRQ handler is protected
by a mutex.
Note 30ms should be more then long enough, at 100KHz any smbus single
byte transaction should be finished in 4ms.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing has shown that writing 1 to clear the read-complete irq does
not work until the data register has been read first.
This commit fixes the driver to read the data register first, halving the
amount of interrupts in most cases since we mostly read on this i2c bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely without locking the smbux_xfer function may miss
the nack flag and further fixes in this patch-set add some more
complex constructions which need protection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C slave controller must be powered and active all the time when I2C
slave backend is registered in order to let master address and
communicate with us.
Now if the controller is runtime PM capable it will be suspended after
probe and cannot ever respond to the master or generate interrupts.
Fix this by resuming the controller when I2C slave backend is registered
and let it suspend after unregistering.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I guess pm_runtime_put_noidle() call in i2c_dw_probe_slave() was copied
by accident from similar master mode adapter registration code. It is
unbalanced due missing pm_runtime_get_noresume() but harmless since it
doesn't decrease dev->power.usage_count below zero.
In theory we can hit similar needless runtime suspend/resume cycle
during slave mode adapter registration that was happening when
registering the master mode adapter. See commit cd998ded5c ("i2c:
designware: Prevent runtime suspend during adapter registration").
However, since we are slave, we can consider it as a wrong configuration
if we have other slaves attached under this adapter and can omit the
pm_runtime_get_noresume()/pm_runtime_put_noidle() calls for simplicity.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If i2c_mux_alloc() fails then we'd have a NULL dereference here.
Fixes: c4aee3e1b0 ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Before I skipped null checks when the master is in the STOP state; this
fixes that.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
24xx BMCs have larger clock divider granularity which can cause problems
when trying to set them as 25xx clock dividers; this adds clock setting
code specific to 24xx.
This also fixes a potential issue where clock dividers were rounded down
instead of up.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-i2c@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use api pair of request_mem_region and release_mem_region
instead of release_resource.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drivers were required to have an I2C device ID table even if were for
devices that would only be registered using a specific firmware interface
(e.g: OF or ACPI).
But commit da10c06a04 ("i2c: Make I2C ID tables non-mandatory for DT'ed
devices") changed the I2C core to relax the requirement and allow drivers
to avoid defining this table.
Unfortunately it only took into account drivers for OF-only devices and
forgot about ACPI-only ones, and this was fixed by commit c64ffff7a9
("i2c: core: Allow empty id_table in ACPI case as well").
But the latter didn't update the original comment, so it doesn't reflect
what the code does now.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code sets bit DW_IC_CON_SPEED_FAST (0x4) always when configuring the slave
mode. This results incorrect register value DW_IC_CON_SPEED_HIGH (0x6)
when OR'ed together with DW_IC_CON_SPEED_STD (0x2).
Remove this and let the code set the speed mode bits according to clock
frequency or default to fast mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When i2c-designware is initialized in slave mode the
i2c-designware-slave.c: i2c_dw_irq_handler_slave() can hit a NULL
pointer dereference when I2C slave backend is not registered but code is
accessing the struct dw_i2c_dev.slave without testing is it NULL.
We might get spurious interrupts from other devices or from IRQ core
during unloading the driver when CONFIG_DEBUG_SHIRQ is set. Existing
check for enable and IRQ status is not enough since device can be power
gated and those bits may read 1.
Fix this by handling the interrupt only when also struct dw_i2c_dev.slave
is set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit 8503ff1665 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.
However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.
Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.
More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.
To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.
Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.
It should also be noted that this change does not fix commit 8503ff1665
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No platform (at least no upstreamed platform) has ever used this
platform_data. Just drop it and simplify the code.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.
This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.
Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for the i2c controller on rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for i2c_algorithm and i2c_adapter_quirks structures that are only
stored in the algo and quirks fields of an i2c_adapter structure
correspondingly. These fields are declared const, so i2c_algorithm and
i2c_adapter_quirks structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for designware)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow i2c-versatile to be enabled for ARM MPS platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata(). In platform_get_drvdata(),
the platform_device is converted back to struct device again.
Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The speed of sending i2c master code in high-speed mode depends on
source clock, clock-div and TIMING register. The source clock and
clock-div of different SoC are not all the same. In order to send
i2c master code at 400k in high-speed mode, a appropriate value
should be set to TIMING register for a certain source clock and
clock-div.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least the Acer Iconia Tab8 / aka W1-810 uses 1MiHz instead of
1MHz for one of its busses, fix this up to 1MHz instead of failing
the probe of that bus.
This fixes the accelerometer on the Acer Iconia Tab8 not working.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we refuse to probe due to an invalid clock frequency, log
the frequency which is causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For now empty ID table is not allowed with ACPI and prevents driver to
be probed.
Add a check to allow empty ID table.
This introduces a helper i2c_acpi_match_device().
Note, we rename some static function in i2c-core-acpi.c to distinguish
with public API.
Fixes: da10c06a04 ("i2c: Make I2C ID tables non-mandatory for DT'ed devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Rajmohan Mani <rajmohan.mani@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: needed to get some drivers probed again]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Kconfig says the resulting module is pinctrl-i2cmux, but the module when
built is i2c-mux-pinctrl.
Fixes: ae58d1e406 ("i2c: Add generic I2C multiplexer using pinctrl API")
Signed-off-by: Chris Gorman <chrisjohgorman@gmail.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Only certain system configurations may use the I2C slave mode so let the
support be optional. This allow reducing module size if needed:
text data bss dec hex filename
10328 1336 16 11680 2da0 drivers/i2c/busses/i2c-designware-core.ko
7222 1136 8 8366 20ae drivers/i2c/busses/i2c-designware-core.ko
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recent i2c-designware slave support patches use master or slave HW init
functions through the function pointer so we can declare them static.
While at it, rename i2c_dw_init() as i2c_dw_init_master().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fixes to spelling mistakes in dev_dbg message
"STAUTS" -> "STATUS"
"SLAVE_ACTTVITY" -> "SLAVE_ACTIVITY"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than returning -ENODEV if i2c_pca_add_numbered_bus() fails,
propagate the error to aid debugging.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When device tree support was added the setting of algo_data.reset_chip
was moved. There were two problems with this. The first being that
i2c_pca_pf_resetchip was only used if platform data was provided. The
second that it was unconditionally overridden with
i2c_pca_pf_dummyreset. Ensure that however the reset gpio is defined the
correct reset_chip function is used.
Fixes: commit 4cc7229daa ("i2c: pca-platform: switch to struct gpio_desc")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI video devices get tagged by the kernel with the custom LNXVIDEO
HID so that normal pnp-id matching can be used and are handled by the
acpi-video driver.
Sometimes the ACPI nodes describing these contain a SERIAL_TYPE_I2C ACPI
resource. Before this commit the presence of this resource would cause the
i2c-core to create a /sys/bus/i2c/devices/i2c-LNXVIDEO:00 device for this
with a modalias of: "i2c:LNXVIDEO:00".
There is no i2c driver for this custom HID, the acpi-video driver binds
directly to the ACPI device /sys/bus/acpi/devices/LNXVIDEO\:00 which has
a modalias of "acpi:LNXVIDEO:" .
Not only is the creation of an i2c-client for this undesirable, it is
actually causing problems. This weird pseudo-resource claims an i2c
speed of 100KHz and typically points to the i2c bus which is used by the
touchscreen controller. Some touchscreen controllers only work properly at
400KHz, at 100KHz they cause errors like these:
i2c_designware 80860F41:03: i2c_dw_handle_tx_abort: lost arbitration
i2c_designware 80860F41:03: i2c_dw_handle_tx_abort: lost arbitration
i2c_designware 80860F41:03: i2c_dw_handle_tx_abort: lost arbitration
i2c_designware 80860F41:03: i2c_dw_handle_tx_abort: lost arbitration
silead_ts i2c-MSSL1680:00: Registers clear error -11
This commit makes the i2c-core ignore LNXVIDEO compatible ACPI devices
which has 2 positive results:
1) The bogus i2c-client for these is no longer created.
2) i2c_acpi_lookup_speed now ignores the 100KHz speed from the pseudo
i2c-resouce and properly returns 400KHz as speed for the touchscreen
i2c bus, fixing the touchscreen not working on various devies.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
- Slave mode selected in platform module if the support is detected in
the DT.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
when supported by the architecture.
All the SLAVE flow is added but it is not enabled via platform
driver.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
0-DAY kernel test reports the following build issue on IA64 architecture
with allmodconfig.
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_writesb':
>> drivers/i2c/busses/i2c-zx2967.c:87:2: error: implicit declaration of function 'writesb' [-Werror=implicit-function-declaration]
writesb(i2c->reg_base + reg, data, len);
^~~~~~~
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_readsb':
>> drivers/i2c/busses/i2c-zx2967.c:93:2: error: implicit declaration of function 'readsb' [-Werror=implicit-function-declaration]
readsb(i2c->reg_base + reg, data, len);
^~~~~~
cc1: some warnings being treated as errors
It's caused by that writesb/readsb are unavailable on IA64 architecture.
Let's drop COMPILE_TEST dependency to avoid the build issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Let's always use the platform device for dev_* and not sometimes the
adapter device as well. Also fix this checkpatch check:
CHECK: Macro argument 'i2c' may be better as '(i2c)' to avoid precedence issues
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to using the devm_ APIs and remove the now unnecessary error
handling and most of the device removal code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: adapted error handling I added in previous patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow devices that use this driver to be registered via a
devicetree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: fixed leakage when registering GPIO failed]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make use of struct gpio_desc which allows us to specify the active state
of the reset pin.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.
This issue was only observed when a system was running much
slower than a normal processor would execute. The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for enforced STOPs will allow us to use SCCB compatible devices.
Based on a preliminary patch by Wolfram Sang.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added slave support for Aspeed I2C controller. Supports fourteen busses
present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add recent findings (IGNORE_NAK) and document in a bit more detail why
the feature is not possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.
Signed-off-by: Michail G Etairidis <m.etairidis@beck-ipc.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f2 ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Definitions were added to core library
- A example was added to designware-core.txt Documentation that shows
how the slave can be setup using DTS
SLAVE related definitions were added to the core of the controller.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- The functions related to I2C master mode of operation were transformed
in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
associated are in a source file called i2c-designware-common and
are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
functions implementation.
Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Factor out all _master() part of code from i2c-designware-core
and i2c-designware-platdrv to separate functions.
- Standardize all code related with MASTER mode.
- I have to take off DW_IC_INTR_TX_EMPTY from DW_IC_INTR_DEFAULT_MASK
because it is master specific.
The purpose of this is to prepare the controller to have is I2C MASTER
flow in a separate driver. To do this first all the
functions/definitions related to the MASTER flow were identified.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The purpose of this commit is to fix some comments and styling in the
existing code due to the need of reuse this code. What is being made
here is:
- Sorted the headers files
- Corrected some comments style (capital letters, lowcase i2c)
- Reverse tree in the variables declaration
- Add/remove empty lines and tabs where needed
- Fix of misspelled word "endianness" and "transferred"
- Replaced the return variable "r" with the more standard "ret"
The value of this, besides the rules of coding style, is because I
will use this code after and it will make my future patch a lot bigger and
complicated to review. The work here won't bring any additional work to
backported fixes because is just style and reordering.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace '%d' by '%zu' to fix the following type of compilation warnings:
drivers/i2c/busses/i2c-at91.c:277:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(dev->dev, "wrote 0x%x, to go %d\n", *dev->buf, dev->buf_len);
^
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Also, add a missing clk_disable_unprepare().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set I2C_CLASS_HWMON for xlp9xx to enable automatic probing of BMC
devices by the ipmi-ssif driver.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig.
Cover Cannon Lake-H too]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The newly added support for the pcc mailbox fails to build
in some configurations:
drivers/i2c/busses/i2c-xgene-slimpro.c: In function 'xgene_slimpro_i2c_probe':
drivers/i2c/busses/i2c-xgene-slimpro.c:516:25: error: implicit declaration of function 'memremap'; did you mean 'memcmp'? [-Werror=implicit-function-declaration]
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: error: 'MEMREMAP_WB' undeclared (first use in this function)
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: note: each undeclared identifier is reported only once for each function it appears in
This includes the missing header file.
Fixes: df5da47fe7 ("i2c: xgene-slimpro: Add ACPI support by using PCC mailbox")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 6c42778780 ("i2c: stub: use pr_fmt") changed the DEBUG
handling and caused build warnings. Revert back to the original.
Fixes: 6c42778780 ("i2c: stub: use pr_fmt")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because we need to transfer some bytes with PIO, the msg length is not
the length of the DMA buffer. Use the correct value which we used when
doing the mapping.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a general purpose i2c mux that uses a multiplexer controlled by
the multiplexer subsystem to do the muxing.
The user can select if the mux is to be mux-locked and parent-locked
as described in Documentation/i2c/i2c-topology.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of printing errors after mxs_i2c_pio_wait_xfer_end returns with
an error code just print a debug message.
NAKs and timeouts can occur in this situation normally, so do not treat
them as errors.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After removal of platform_data support, we can simplify OF handling.
of_match_device() evaluates to NULL if !CONFIG_OF or if there is no node
pointer for that device, so we can remove the check for the node ptr.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No platform currently upstream makes use of this platform_data anymore.
The ones that did are converted to DT meanwhile. So, remove it. The old
platforms likely don't have the 'clks_per_cnt' feature, otherwise it
would have been implemented by now. And in the unlikely case they need
to setup a different bus speed, we should rather go for a generic i2c
platform data just for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of hard coding "i2c-stub:", let's use the pr_fmt mechanism to
achieve the same more easily. This makes it easier to stay consistent
when adding new messages. Also, remove an unneeded OOM message while we
are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds ACPI support by using PCC mailbox communication
interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch refactors the code to use a single message function to
send command message.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Finally, apply modern comment rules to the file header. The old style
looked very non-Linuxish and challenged my eyes for some time now. I
also added my own copyright for the period of me being the maintainer.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
They seem like cruft to me. I couldn't find any evidence that something
included from there is actually used.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Removes some ifdeffery. Also add the new file to the relevant
MAINTAINERS section.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Break out the exported SMBus functions and the emulation layer into a
separate file. This also involved splitting up the tracing header into
an I2C and an SMBus part.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core became quite huge and its monolithic structure makes
maintenance hard. So, prepare to break out some functionality into
separate files by renaming the source file. Note that we keep the
resulting object name constant to avoid regressions.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Fixes: 9d64084330 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit bd698d24b1 ("i2c: designware: Get selected speed mode
sda-hold-time via ACPI") updated the logic that reads the timing
parameters for various I2C bus rates from the DSDT, to only read
the timing parameters for the currently selected mode.
This causes a WARN_ON() splat on platforms that legally omit the clock
frequency from the ACPI description, because in the new situation, the
core I2C designware driver still accesses the fields in the driver
struct that we no longer populate, and proceeds to calculate them from
the clock frequency. Since the clock frequency is unspecified, the
driver complains loudly using a WARN_ON().
So revert back to the old situation, where the struct fields for all
timings are populated, but retain the new logic which chooses the SDA
hold time from the timing mode that is currently in use.
Fixes: bd698d24b1 ("i2c: designware: Get selected speed mode ...")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With ACPI, i2c-core requires ACPI companion to be set in order for it
to create slave device.
This patch sets the ACPI companion accordingly.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no reason to use platform_get_irq() for non-DT probing and
irq_of_parse_and_map() for DT probing. Indeed, platform_get_irq()
works fine for both.
In addition, using platform_get_irq() properly returns -EPROBE_DEFER
when the interrupt controller is not yet available, so instead of
inventing our own error code (-ENXIO), return the one provided by
platform_get_irq().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As is, a failure message is printed unconditionally, which is confusing.
And noisy.
Fixes: 8d4d159f25 ("i2c: mux: provide more info on failure in i2c_mux_add_adapter")
Signed-off-by: Peter Rosin <peda@axentia.se>
It is only prudent to let go of resources that are not used.
Fixes: b3fdd32799 ("i2c: mux: Add register-based mux i2c-mux-reg")
Signed-off-by: Peter Rosin <peda@axentia.se>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
Pull input subsystem updates from Dmitry Torokhov:
- a big update from Mauro converting input documentation to ReST format
- Synaptics PS/2 is now aware of SMBus companion devices, which means
that we can now use native RMI4 protocol to handle touchpads, instead
of relying on legacy PS/2 mode.
- we removed support from BMA180 accelerometer from input devices as it
is now handled properly by IIO
- update to TSC2007 to corretcly report pressure
- other miscellaneous driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits)
Input: ar1021_i2c - use BIT to check for a bit
Input: twl4030-pwrbutton - use input_set_capability() helper
Input: twl4030-pwrbutton - use correct device for irq request
Input: ar1021_i2c - enable touch mode during open
Input: add uinput documentation
dt-bindings: input: add bindings document for ar1021_i2c driver
dt-bindings: input: rotary-encoder: fix typo
Input: xen-kbdfront - add module parameter for setting resolution
ARM: pxa/raumfeld: fix compile error in rotary controller resources
Input: xpad - do not suggest writing to Dominic
Input: xpad - don't use literal blocks inside footnotes
Input: xpad - note that usb/devices is now at /sys/kernel/debug/
Input: docs - freshen up introduction
Input: docs - split input docs into kernel- and user-facing
Input: docs - note that MT-A protocol is obsolete
Input: docs - update joystick documentation a bit
Input: docs - remove disclaimer/GPL notice
Input: fix "Game console" heading level in joystick documentation
Input: rotary-encoder - remove references to platform data from docs
Input: move documentation for Amiga CD32
...
Pull i2c updates from Wilfram Sang:
"I2C has the following updates for you:
- an immutable cross-subsystem branch fixing PMIC access on Intel
Baytrail
- bigger driver updates to the designware, meson, exynos5 drivers
- new i2c_acpi_new_device() function to create devices from ACPI
- struct i2c_driver has now a flag 'disable_i2c_core_irq_mapping' to
allow custom IRQ mapping in case the default does not fit
- mux subsystem centralized error messages in its core
- new driver for ltc4306 i2c mux
- usual set of small updates"
* 'i2c/for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: thunderx: Enable HWMON class probing
i2c: rcar: clarify PM handling with more comments
i2c: rcar: fix resume by always initializing registers before transfer
i2c: tegra: fix spelling mistake: "contoller" -> "controller"
i2c: exynos5: use core helper to get driver data
i2c: exynos5: de-duplicate error logs on clock setup
i2c: exynos5: simplify clock frequency handling
i2c: exynos5: simplify timings calculation
i2c: designware-baytrail: fix potential null pointer dereference on dev
i2c: designware: Get selected speed mode sda-hold-time via ACPI
[media] cx231xx: stop double error reporting
i2c: core: Allow drivers to disable i2c-core irq mapping
i2c: core: Add new i2c_acpi_new_device helper function
i2c: core: Allow getting ACPI info by index
i2c: img-scb: use setup_timer
i2c: i2c-scmi: add a MS HID
i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch
dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch
i2c: mux: reg: stop double error reporting
i2c: mux: pinctrl: stop double error reporting
...
Add ACPI HID HISI02A1 and HISI02A2 for Hisilicon Hip07/08,
which have different clock frequency.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Set I2C_CLASS_HWMON to enable automatic probing of BMC devices
by the ipmi-ssif driver.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
PM handling is correct but might be a bit subtle. Add some comments for
clarification.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Resume failed because of uninitialized registers. Instead of adding a
resume callback, we simply initialize registers before every transfer.
This lightweight change is more robust and will keep us safe if we ever
need support for power domains or dynamic frequency changes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
trivial fix to spelling mistake in MODULE_DESCRIPTION text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver core provides of_device_get_match_data which can be used
to get driver data instead of custom helper.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of clock setup error it is enough to log it once.
Moreover patch simplifies clock setup routines.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to keep separate settings for high and fast speed clock.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using cryptic loop direct calculation of timings
can be used.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/i2c/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
cc: linux-i2c@vger.kernel.org
The assignment to addr requires a call to get_sem_addr that dereferences
dev, however, this dereference occurs before a null pointer check on dev.
Move this assignment after the null check on dev to avoid a potential null
pointer dereference.
Detected by CoverityScan, CID#1419700 ("Dereference before null check")
Fixes: fd476fa22a ("i2c: designware-baytrail: Add support for cherrytrail")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sda-hold-time is an important parameter for tuning i2c to meet the
electrical specification especially for high speed. I2C with incorrect
sda-hold-time may cause lost arbitration error. Instead of loading all
speed mode settings, only selected speed mode settings are loaded.
Signed-off-by: Tan Chin Yew <chin.yew.tan@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
By default the i2c-core will try to get an irq with index 0 on ACPI / of
instantiated devices. This is troublesome on some ACPI systems where the
irq info at index 0 in the CRS table may contain nonsense and/or point
to an irqchip for which there is no Linux driver.
If this happens then before this commit the driver's probe method would
never get called because i2c_device_probe will try to get an irq by
calling acpi_dev_gpio_irq_get which will always return -EPROBE in this
case, as it waits for a matching irqchip driver to load. Thus causing
the driver to not get a chance to bind.
This commit adds a new disable_i2c_core_irq_mapping flag to struct
i2c_driver which a driver can set to tell the core to skip irq mapping.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
By default the i2c subsys creates an i2c-client for the first I2cSerialBus
resource of an acpi_device, but some acpi_devices have multiple
I2cSerialBus resources and we may want to instantiate i2c-clients for
the others.
This commit adds a new i2c_acpi_new_device function which can be used to
create an i2c-client for any I2cSerialBus resource of an acpi_device.
Note that the other resources may even be on a different i2c bus, so just
retrieving the client address is not enough.
Here is an example DSDT excerpt from such a device:
Device (WIDR)
{
Name (_HID, "INT33FE" /* XPOWER Battery Device */)
Name (_CID, "INT33FE" /* XPOWER Battery Device */)
Name (_DDN, "WC PMIC Battery Device")
<snip>
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x005E, ControllerInitiated, 0x000186A0,
AddressingMode7Bit, "\\_SB.PCI0.I2C7",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0036, ControllerInitiated, 0x000186A0,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0022, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
I2cSerialBusV2 (0x0054, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C1",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0012
}
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0005
}
GpioInt (Level, ActiveLow, Exclusive, PullNone, 0x0000,
"\\_SB.PCI0.I2C7.PMI5", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
})
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Return (RBUF) /* \_SB_.PCI0.I2C7.WIDR.RBUF */
}
<snip>
}
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Modify struct i2c_acpi_lookup and i2c_acpi_fill_info() to allow
using them to get the info from a certain index in the ACPI-resource
list rather then taking the first I2cSerialBus resource.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Description of the problem:
- i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM";
- the fist HID (SMBUS01) is clearly defined in "SMBus Control Method
Interface Specification, version 1.0": "Each device must specify
'SMBUS01' as its _HID and use a unique _UID value";
- unfortunately, BIOS vendors (like AMI) seem to ignore this requirement
and implement "SMB0001" HID instead of "SMBUS01";
- I speculate that they do this because only "SMB0001" is hard coded in
Windows SMBus driver produced by Microsoft.
This leads to following situation:
- SMBus works out of box in Windows but not in Linux;
- board vendors are forced to add correct "SMBUS01" HID to BIOS to make
SMBus work in Linux. Moreover the same board vendors complain that
tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier
and produce errors. So they need to constantly patch the compiler for
each new version of BIOS.
As it is very unlikely that BIOS vendors implement a correct HID in
future, I would propose to consider whether it is possible to work around
the problem by adding MS HID to the Linux i2c-scmi driver.
v2: move the definition of the new HID to the driver itself.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Signed-off-by: Michael Brunner <Michael.Brunner@kontron.com>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the Analog Devices / Linear Technology
LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches.
The LTC4306 optionally provides two general purpose input/output pins
(GPIOs) that can be configured as logic inputs, opendrain outputs or
push-pull outputs via the generic GPIOLIB framework.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY6mY1AAoJEHm+PkMAQRiGB14IAImsH28JPjxJVDasMIRPBxVc
euPPlZgoBieu7sNt+kEsEqdkXuu0MLk6gln0IGxWLeoB2S+u3Tz5LMa2YArVqV9Z
tWzOnI9auE73P2Pz/tUMOdyMs5tO0PolQxX3uljbULBozOHjHRh13fsXchX2yQvl
mFeFCDqpPV0KhWRH/ciA8uIHdvYPhMpkKgRtmR8jXL0yzqLp6+2J+Bs8nHG4NNng
HMVxZPC8jOE/TgWq6k/GmXgxh3H/AideFdHFbLKYnIFJW41ZGOI8a262zq3NmjPd
lywpVU7O7RMhSITY5PnuR3LpNV8ftw1hz2y6t35unyFK1P02adOSj5GJ3hGdhaQ=
=Xz5O
-----END PGP SIGNATURE-----
Backmerge tag 'v4.11-rc6' into drm-next
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
No callers then need to report any further info, thus reducing both the
amount of code and the log noise.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Simple integer for interrupt number is not expressive enough, as it does
not convey interrupt trigger type that should be used. Let's allow
attaching array of resources to the board info and have i2c core parse
first IRQ resource and set up interrupt trigger as needed.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This will allow marking device property lists as __initdata, the same as
board info structures themselves.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c bus has 2 different types of device belonging to the same bus and
bus notifiers use device type to distinguish between adapters and clients.
Previously we only had i2c_adapter_type exported, which made code wanting
to work with i2c_client devices test for type not equal to adapter type.
This unfortunately is not safe if we ever add another type to the bus,
so let's export i2c_client_type as well.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The preceding changes in this patch series now allow to simplify
the interrupt handler significantly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
meson_i2c_write_tokens is always called directly after
meson_i2c_prepare_xfer (and only then). So we can simplify the code by
removing meson_i2c_write_tokens and moving the two statements of
meson_i2c_write_tokens to the end of meson_i2c_prepare_xfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can directly add the stop token to the token chain including the
last transfer chunk. This is more efficient than creating a separate
token chain just for the stop command.
And it allows us to get rid of state STATE_STOP completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If state is STATE_IDLE no interrupt should occur. Return IRQ_NONE
if such a spurious interrupt is detected.
Not having to take care of STATE_IDLE later in the interrupt handler
allows to further simplify the interrupt handler in subsequent
patches of this series.
In addition move resetting REG_CTRL_START bit to the start of the
interrupt handler to ensure that the start bit is always reset.
Currently the start bit is not reset for STATE_STOP because
i2c->state is set to STATE_IDLE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Variable count has always the same value as i, so we don't need it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The clock divider has 12 bits, splitted into a 10 bit field and a
2 bit field. The extra 2 bits aren't used currently.
Change this to use the full 12 bits and warn if the requested
frequency is too low.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't have to parse the DT manually to retrieve the bus frequency
and we don't have to maintain an own default for the bus frequency.
Let the i2c core do this for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The bus frequency is fixed to what is set DT, therefore we can set
the clock divider in probe already and we don't have to set it for
each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Member irq can be replaced with a local variable in probe
because it's nowhere else accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use min instead of min_t where min_t isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The spec for the pca9546 was missing. This chip is the same as the pca9545
except that it lacks interrupt lines. While the i2c_device_id table mapped
the pca9546 to the pca9545 definition the compatible table did not.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Peter Rosin <peda@axentia.se>
In ACPI world any ID should be carefully chosen and registered
officially. The commit bbf9d262a1 seems did a wrong assumption because
PCA is the registered PNP ID for "PHILIPS BU ADD ON CARD". I'm pretty
sure this prefix has nothing to do with the driver in question.
Moreover, newer ACPI specification has a support of _DSD method and
special device IDs to allow drivers be enumerated via compatible string.
The slight change to support this kind of enumeration will be added in
sequential patch against pca954x.c.
Revert the commit bbf9d262a1 for good.
Cc: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Add support for reading the system clock and the TWSI clock
frequency from ACPI DSDT.
TWSI clock was already covered by using device_property_read().
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of the platform.
Update compile dependencies and ACPI ID to reflect this change. There
is not need to retain ARCH_VULCAN since the Vulcan processor was never
in production and the config option will be removed soon.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the Tegra BPMP I2C adapter by default if the Tegra BPMP itself
is enabled. This adapter is used as the I2C interface for the PMIC on
the Tegra186 Jetson-TX2 platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYzznuAAoJEHm+PkMAQRiGAzMIAJDBo5otTMMLhg8eKj8Cnab4
2NyaoWDN6mtU427rzEKEfZlTtp3gIBVdFex5x442weIdw6BgRQW0dvF/uwEn08yI
9Wx7VJmIUyH9M8VmhDtkUTFrhwUGr29qb3JhENMd7tv/CiJaehGRHCT3xqo5BDdu
xiyPcwSkwP/NH24TS91G87gV6r0I0oKLSAxu+KifEFESrb8gaZaduslzpEj3m/Ds
o9EPpfzaiGAdW5EdNfPtviYbBk7ZOXwtxdMV+zlvsLcaqtYnFEsJZd2WyZL0zGML
VXBVxaYtlyTeA7Mt8YYUL+rDHELSOtCeN5zLfxUvYt+Yc0Y6LFBLDOE5h8b3eCw=
=uKUo
-----END PGP SIGNATURE-----
BackMerge tag 'v4.11-rc3' into drm-next
Linux 4.11-rc3 as requested by Daniel
Cherrytrail devices use the dw i2c-bus with uid 7 to access their PMIC.
Even if the i2c-bus to the PMIC is not shared with the SoC's P-Unit
and i2c-designware-baytrail.c thus does not set the pm_disabled flag,
we still need to disable pm so that ACPI PMIC opregions can access the
PMIC during late-suspend and early-resume.
This fixes errors like these blocking suspend:
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently we are already setting a pm_runtime_disabled flag and disabling
runtime-pm for i2c-busses used for accessing the system PMIC on x86.
But this is not enough, there are ACPI opregions which may want to access
the PMIC during late-suspend and early-resume, so we need to completely
disable pm to be safe.
This commit renames the flag from pm_runtime_disabled to pm_disabled and
adds the following new behavior if the flag is set:
1) Call dev_pm_syscore_device(dev, true) which disables normal suspend /
resume and remove the pm_runtime_disabled check from dw_i2c_plat_resume
since that will now never get called. This fixes suspend_late handlers
which use ACPI PMIC opregions causing errors like these:
PM: Suspending system (freeze)
PM: suspend of devices complete after 1127.751 msecs
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
2) Set IRQF_NO_SUSPEND irq flag. This fixes resume_early handlers which
handlers which use ACPI PMIC opregions causing errors like these:
PM: resume from suspend-to-idle
i2c_designware 808622C1:06: controller timed out
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Our testing shows the semaphore failing to be transferred on CherryTrail
in about 0.5% of all cases. The existing timeout needs to be lengthened
to accommodate the worst cases.
V2: Rebased on https://cgit.freedesktop.org/drm-intel/commit/?h=topic/designware-baytrail
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull immutable branch as a common base for further development:
"Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix."
The pca954x i2c mux driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit b0c1e95ab4. It
contains a flaw and the next version has more features added which makes
me want to move it to the next cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 02dbfa5e55. I grabbed
the wrong version from the list and will pull the proper one from Peter
Rosin's mux tree.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After commit 7999eecb7e ("i2c: exynos5: fix arbitration lost handling"),
some I2C transactions are failing because the TRANSFER_DONE_AUTO field is
not set in the I2C_TRANS_STATUS register so the i2c->status value is left
to -EINVAL causing the i2c->msg_complete completion to never be signaled.
For example, when reading the time of an I2C rtc on an Exynos5800 machine:
$ cat /sys/class/rtc/rtc0/time
[ 25.924594] exynos5-hsi2c 12e10000.i2c: rx timeout
[ 65.028365] max77686-rtc max77802-rtc: Fail to read time reg(-22)
cat: /sys/class/rtc/rtc0/time: Invalid argument
The Exynos5422 manual states clearly that most I2C_TRANS_STATUS reg bits
(including TRANSFER_DONE_AUTO) are cleared after the register is read. So
reading has side effects and should only be done if HSI2C_INT_I2C was set.
Fixes: 7999eecb7e ("i2c: exynos5: fix arbitration lost handling")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some platforms like hi3660 need do reset first to allow accessing registers
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ramiro Oliveira <ramiro.oliveira@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This will allow marking device property lists as __initdata, the same as
board info structures themselves.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All length fields in Linux I2C are u16, so a HW length limitation of 16
bit lengths is not a limitation. Remove the quirk structure.
Tested-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BSC data buffers to send and receive data are each of size 32 bytes
or 8 bytes 'xfersz' depending on SoC. The problem observed for all the
combined message transfer was if length of data transfer was a multiple
of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed
this by appropriately setting START/STOP conditions for such transfers.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refcount of of_node is increased with of_node_get() in i2c_mux_add_adapter().
It must be decreased with of_node_put() in i2c_mux_del_adapters().
Signe-off-by: Qi Hou <qi.hou@windriver.com>
Reviewed-by: Zhang Xiao <xiao.zhang@windriver.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095e ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refcount of of_node is increased with of_node_get() in i2c_mux_add_adapter().
It must be decreased with of_node_put() in i2c_mux_del_adapters().
Cc: stable@vger.kernel.org
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Reviewed-by: Zhang Xiao <xiao.zhang@windriver.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acquire P-Unit access to stop others from accessing the P-Unit while the
PMIC i2c bus is in use. This is necessary because accessing the P-Unit
from the kernel may result in the P-Unit trying to access the PMIC i2c
bus, which results in a hang when it happens while we own the PMIC i2c
bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=155241
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: tagorereddy <tagore.chandan@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-10-hdegoede@redhat.com
The cherrytrail punit has the pmic i2c bus access semaphore at a
different register address.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-9-hdegoede@redhat.com
Use iosf_mbi_modify instead of iosf_mbi_read + iosf_mbi_write so that
we keep the iosf_mbi_lock locked during the read-modify-write done to
reset the semaphore.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-8-hdegoede@redhat.com
On my cherrytrail tablet with axp288 pmic, just doing a bunch of repeated
reads from the pmic, e.g. "i2cdump -y 14 0x34" would lookup the tablet in
1 - 3 runs guaranteed.
This seems to be causes by the cpu trying to enter C6 or C7 while we hold
the punit bus semaphore, at which point everything just hangs.
Avoid this by disallowing the CPU to enter C6 or C7 before acquiring the
punit bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-7-hdegoede@redhat.com
If (!shared_host) simply return 0, this avoids delaying the probe if
iosf_mbi_available() returns false when an i2c bus is not using the
punit semaphore.
Also move the if (!iosf_mbi_available()) check to above the
dev_info, so that we do not repeat the dev_info on every probe
until iosf_mbi_available() returns true.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-6-hdegoede@redhat.com
Pass dw_i2c_dev into the helper functions, this is a preparation patch
for the punit semaphore fixes done in the other patches in this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-5-hdegoede@redhat.com
Rename accessor_flags to flags, so that we can use the field for
other flags too. This is a preparation patch for adding cherrytrail
support to the punit semaphore code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-4-hdegoede@redhat.com
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has for you two new drivers (Tegra BPMP and STM32F4), interrupt
support for pca954x muxes, and a bunch of driver bugfixes and
improvements. Nothing really special this cycle.
A few commits have been added to my tree just recently. Those are the
Tegra BPMP driver and a few straightforward bugfixes or cleanups which
I prefer to have upstream rather soonish. The rest had proper
linux-next exposure"
* 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (25 commits)
i2c: thunderx: Replace pci_enable_msix()
i2c: exynos5: fix arbitration lost handling
i2c: exynos5: disable fifo-almost-empty irq signal when necessary
i2c: at91: ensure state is restored after suspending
i2c: bcm2835: Avoid possible NULL ptr dereference
i2c: Add Tegra BPMP I2C proxy driver
dt-bindings: Add Tegra186 BPMP I2C binding
misc: eeprom: at24: use device_property_*() functions instead of of_get_property()
i2c: mux: pca954x: Add interrupt controller support
dt: bindings: i2c-mux-pca954x: Add documentation for interrupt controller
i2c: mux: pca954x: Add missing pca9542 definition to chip_desc
i2c: riic: correctly finish transfers
i2c: i801: Add support for Intel Gemini Lake
i2c: mux: pca9541: Export OF device ID table as module aliases
i2c: mux: pca954x: Export OF device ID table as module aliases
i2c: mux: mlxcpld: remove unused including <linux/version.h>
i2c: busses: constify i2c_algorithm structures
i2c: i2c-mux-gpio: rename i2c-gpio-mux to i2c-mux-gpio
i2c: sh_mobile: document support for r8a7796 (R-Car M3-W)
i2c: i2c-cros-ec-tunnel: Reduce logging noise
...
Using pci_alloc_irq_vectors() instead of the deprecated
pci_enable_msix() allows to remove the msix_entry from
struct octeon_i2c and thus to get rid of the config symbol check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of arbitration lost adequate interrupt sometimes is not signaled.
As a result transfer timeouts and is not retried, as it should. To avoid
such cases code is added to check transaction status in case of every
interrupt.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fifo-almost-empty irq signal should be disabled as soon as possible,
to avoid unnecessary interrupt storm. The best moment is when there is
no more data to feed fifo.
This patch fixes system stalls caused by IRQ storm.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow built-in (static) device properties to be declared
as constant, make it possible to save memory by discarding
alternative (but unused) built-in (static) property sets and
add support for automatic handling of built-in properties
to the I2C code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+P7T
-----END PGP SIGNATURE-----
Merge tag 'device-properties-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device property updates from Rafael J. Wysocki:
"Generic device properties framework updates for v4.11-rc1
Allow built-in (static) device properties to be declared as constant,
make it possible to save memory by discarding alternative (but unused)
built-in (static) property sets and add support for automatic handling
of built-in properties to the I2C code"
* tag 'device-properties-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: allow specify device properties in i2c_board_info
device property: export code duplicating array of property entries
device property: constify property arrays values
device property: allow to constify properties
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
* Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng).
* ACPI resources handling fix related to invalid resource
descriptors (Bob Moore).
* Fix to enable implicit result conversion for several ASL
library functions (Bob Moore).
* Support for method invocations as target operands in AML
(Bob Moore).
* Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore).
* Utilities updates (Bob Moore, Lv Zheng).
* Disassembler/debugger updates (David Box, Lv Zheng).
* Build fixes (Colin Ian King, Lv Zheng).
* Update of copyright notices in all files (Bob Moore).
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan).
- Fixes for the ACPI EC and button drivers (Lv Zheng).
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov).
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui).
- Message formatting fix for the ACPI APEI code (Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aJJ+
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170119, which among other things updates copyright notices in all of
the ACPICA files, fix a couple of issues in the ACPI EC and button
drivers, fix modalias handling for non-discoverable devices with
DT-compatible identification strings, add a suspend quirk for one
platform and fix a message in the APEI code.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
+ Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng)
+ ACPI resources handling fix related to invalid resource
descriptors (Bob Moore)
+ Fix to enable implicit result conversion for several ASL library
functions (Bob Moore)
+ Support for method invocations as target operands in AML (Bob
Moore)
+ Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore)
+ Utilities updates (Bob Moore, Lv Zheng)
+ Disassembler/debugger updates (David Box, Lv Zheng)
+ Build fixes (Colin Ian King, Lv Zheng)
+ Update of copyright notices in all files (Bob Moore)
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan)
- Fixes for the ACPI EC and button drivers (Lv Zheng)
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov)
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui)
- Message formatting fix for the ACPI APEI code (Colin Ian King)"
* tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Update version to 20170119
ACPICA: Tools: Update common signon, remove compilation bit width
ACPICA: Source tree: Update copyright notices to 2017
ACPICA: Linuxize: Restore and fix Intel compiler build
x86/ACPI: keep x86_cpu_to_acpiid mapping valid on CPU hotplug
spi: acpi: Initialize modalias from of_compatible
i2c: acpi: Initialize info.type from of_compatible
ACPI / bus: Introduce acpi_of_modalias() equiv of of_modalias_node()
ACPI: save NVS memory for Lenovo G50-45
ACPI, APEI, EINJ: fix malformed newline escape
ACPI / button: Remove lid_init_state=method mode
ACPI / button: Change default behavior to lid_init_state=open
ACPI / EC: Use busy polling mode when GPE is not enabled
ACPI / EC: Remove old CLEAR_ON_RESUME quirk
ACPICA: Update version to 20161222
ACPICA: Parser: Update parse info table for some operators
ACPICA: Fix a problem with recent extra support for control method invocations
ACPICA: Parser: Allow method invocations as target operands
ACPICA: Fix for implicit result conversion for the ToXXX functions
ACPICA: Resources: Not a valid resource if buffer length too long
..
When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit e247454103 ("bcm2835: Fix hang for writing messages
larger than 16 bytes") the interrupt handler is prone to a possible
NULL pointer dereference. This could happen if an interrupt fires
before curr_msg is set by bcm2835_i2c_xfer_msg() and randomly occurs
on the RPi 3. Even this is an unexpected behavior the driver must
handle that with an error instead of a crash.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: e247454103 ("bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Tegra BPMP I2C driver. The BPMP is the boot and power management
processor embedded in Tegra SoCs. In newer SoC versions, access to one
of the I2C busses goes via the BPMP, requiring a different "proxy" I2C
driver that accesses the bus via the real I2C driver embedded in the
BPMP firmware.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Various muxes can aggregate multiple interrupts from each i2c bus.
All of the muxes with interrupt support combine the active low irq lines
using an internal 'and' function and generate a combined active low
output. The muxes do provide the ability to read a control register to
determine which irq is active. By making the mux an irq controller isr
latency can potentially be reduced by reading the status register and
then only calling the registered isr on that bus segment.
As there is no irq masking on the mux irq are disabled until irq_unmask is
called at least once.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Peter Rosin <peda@axentia.se>
The spec for the pca954x was missing. This chip is the same as the pca9540
except that it has interrupt lines. While the i2c_device_id table mapped
the pca9542 to the pca9540 definition the compatible table did not. In
preparation for irq support add the pca9542 definition.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Peter Rosin <peda@axentia.se>
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a414 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare i2c_algorithm structures as const as they are only stored in the
algo field of an i2c_adapter structure. This field is of type const, so
i2c_algorithm structures having this property can be made const too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> for
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With many drivers converting to using generic device properties, it is
useful to provide array of device properties when instantiating new i2c
client via i2c_board_info and have them automatically added to the device
in question.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using devicetree i2c_board_info.type is set to the compatible
string with the vendor prefix removed. For I2C devices described via
ACPI the i2c_board_info.type string is set to the ACPI device name. When
using ACPI and DT ids this string ends up something like "PRP0001:00".
If the of_compatible property is present try to use that instead. This
makes it easier to instantiate i2c drivers through ACPI with DT ids.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an i2c access through i2c-cros-ec-tunnel returns an error, the following
log message is seen on the console.
cros-ec-i2c-tunnel ff200000.spi:ec@0:i2c-tunnel:
Error parsing EC i2c message -121
This can happen a lot if, for example, the i2c-detect command is executed.
Since it is perfectly normal for an i2c controller to report an error,
drop the message. Also, report -ENXIO instead of -EREMOTEIO if the access
error is due to NAK from the device, and return -EIO instead of -EREMOTEIO
for other errors, as suggested in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function has the purpose of mode detection by checking the
device nodes for a reg matching with the I2C_OWN_SLAVE_ADDREESS flag.
Currently only checks using OF functions (ACPI slave not supported yet).
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When system enters VLLS mode, module power is turned off. As a result,
all registers are reset to HW default value. After exiting VLLS mode,
registers are still in default mode. As a result, the pinctrl settings
are incorrect, which will affect the module function.
The patch recovers the pinctrl setting when exit VLLS mode.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
[wsa: added missing include]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit implements suspend/resume support in the mv64xxx I2C
controller driver. There is no need to implement a ->suspend() hook, as
calling mv64xxx_i2c_hw_init() at ->resume() time is enough.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Lior Amsalem <alior@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
[Thomas: switch to dev_pm_ops, fix build warning when !PM.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the STM32F4 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On AMD's SB800 and upwards, the SMBus is shared with the Integrated
Micro Controller (IMC).
The platform provides a hardware semaphore to avoid race conditions
among them. (Check page 288 of the SB800-Series Southbridges Register
Reference Guide http://support.amd.com/TechDocs/45482.pdf)
Without this patch, many access to the SMBus end with an invalid
transaction or even with the bus stalled.
Reported-by: Alexandre Desnoyers <alex@qtec.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>:
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistake in WARN message, insufficient has
an insufficient number of i's in the spelling.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In of_i2c_register_device(), when the check for
device address validity fails we print the info.addr,
which has not been assigned properly.
Fix this by printing the actual invalid address.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: b4e2f6ac12 ("i2c: apply DT flags when probing")
Cc: stable@kernel.org
Falling back unconditionally to HostNotify as primary client's interrupt
breaks some drivers which alter their functionality depending on whether
interrupt is present or not, so let's introduce a board flag telling I2C
core explicitly if we want wired interrupt or HostNotify-based one:
I2C_CLIENT_HOST_NOTIFY.
For DT-based systems we introduce "host-notify" property that we convert
to I2C_CLIENT_HOST_NOTIFY board flag.
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater).
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making mlxcpld_mux_reg_write() return a -ve error code for
all failure cases, just as was done in commit 7f638c1cb0 ("i2c: mux:
pca954x: fix i2c mux selection caching").
This also aligns the implementations of these two muxes in this area.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In DTB case, i2c-core doesn't create slave device which is installed
on i2c-xgene bus because of missing code in this driver.
This patch fixes this issue.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.
Fixes: 463e8f845c ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -EIO in case of a failed data read. For all other
cases just return so subsequent operations will fail
and trigger the recovery.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
o STM can hook into the function tracer
o Function filtering now supports more advance glob matching
o Ftrace selftests updates and added tests
o Softirq tag in traces now show only softirqs
o ARM nop added to non traced locations at compile time
o New trace_marker_raw file that allows for binary input
o Optimizations to the ring buffer
o Removal of kmap in trace_marker
o Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
o Other various fixes and clean ups
Note, there are two patches marked for stable. These were discovered
near the end of the 4.9 rc release cycle. By the time I had them tested
it was just a matter of days before 4.9 would be released, and I
figured I would just submit them in the merge window. They are old
bugs and not critical. Nothing non-root could abuse.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJYUrFHFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
2+AIAIr20kSQV/nA5htGAeCTobVk3WUxY6bvjd9mIJDKPP19akNLyREW0G3KnfCr
yhx4aFRZG98fRu/6F8qieRosyN36lADDVYHelMFHMpcTOpE2aZGjaaOuNGxOEA9v
FmMPTX+K3+dzKyFP4l68R3+5JuQ1/AqLTioTWeLW8IDQ2OOVsjD8+0BuXrNKMJDY
o6U4Hk5U/vn+zHc6BmgBzloAXemBd7iJ1t5V3FRRGvm8yv3HU85Twc5ofGeYTWvB
J8PboEywRlIzxg0Kd8mxnMI5PgaKZSEc2ub8E7cY/CZ5PYpDE2xDA2hJmJgfYp00
1VW+DHRpRZfElsCcya6S6P4bs5Y=
=MGZ/
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This release has a few updates:
- STM can hook into the function tracer
- Function filtering now supports more advance glob matching
- Ftrace selftests updates and added tests
- Softirq tag in traces now show only softirqs
- ARM nop added to non traced locations at compile time
- New trace_marker_raw file that allows for binary input
- Optimizations to the ring buffer
- Removal of kmap in trace_marker
- Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
- Other various fixes and clean ups"
* tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (42 commits)
selftests: ftrace: Shift down default message verbosity
kprobes/trace: Fix kprobe selftest for newer gcc
tracing/kprobes: Add a helper method to return number of probe hits
tracing/rb: Init the CPU mask on allocation
tracing: Use SOFTIRQ_OFFSET for softirq dectection for more accurate results
tracing/fgraph: Have wakeup and irqsoff tracers ignore graph functions too
fgraph: Handle a case where a tracer ignores set_graph_notrace
tracing: Replace kmap with copy_from_user() in trace_marker writing
ftrace/x86_32: Set ftrace_stub to weak to prevent gcc from using short jumps to it
tracing: Allow benchmark to be enabled at early_initcall()
tracing: Have system enable return error if one of the events fail
tracing: Do not start benchmark on boot up
tracing: Have the reg function allow to fail
ring-buffer: Force rb_end_commit() and rb_set_commit_to_write() inline
ring-buffer: Froce rb_update_write_stamp() to be inlined
ring-buffer: Force inline of hotpath helper functions
tracing: Make __buffer_unlock_commit() always_inline
tracing: Make tracepoint_printk a static_key
ring-buffer: Always inline rb_event_data()
ring-buffer: Make rb_reserve_next_event() always inlined
...
Pull i2c updates from Wolfram Sang:
- the first series of making i2c_device_id optional instead of
mandatory (in favor of alternatives like of_device_id).
This involves adding a new probe callback (probe_new) which removes
some peculiarities I2C had for a long time now. The new probe is
matching the other subsystems now and the old one will be removed
once all users are converted. It is expected to take a while but
there is ongoing interest in that.
- SMBus Host Notify introduced 4.9 got refactored. They are now using
interrupts instead of the alert callback which solves multiple
issues.
- new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux
- significant refactoring for bcm2835 driver
- the usual set of driver updates and improvements
* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
i2c: fsl-lpi2c: read lpi2c fifo size in probe()
i2c: octeon: thunderx: Remove double-check after interrupt
i2c: octeon: thunderx: TWSI software reset in recovery
i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
i2c: sh_mobile: Add per-Generation fallback bindings
i2c: rcar: Add per-Generation fallback bindings
i2c: imx-lpi2c: add low power i2c bus driver
dt-bindings: i2c: imx-lpi2c: add devicetree bindings
i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
i2c: pxa: Add support for the I2C units found in Armada 3700
i2c: pxa: Add definition of fast and high speed modes via the regs layout
dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
i2c: qup: support SMBus block read
i2c: qup: add ACPI support
i2c: designware: Consolidate default functionality bits
i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
i2c: mux: pca954x: Add ACPI support for pca954x
i2c: use an IRQ to report Host Notify events, not alert
i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
i2c: i801: use the BIT() macro for FEATURES_* also
...
The lpi2c fifo size is a read only parameter resides Parameter
Register. It's better to read lpi2c tx/rx fifo size in probe()
other than just define a macro for it.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1bb1ff3e7c ("i2c: octeon: Improve performance if interrupt is
early") added a double-check around the wait_event_timeout() condition.
The performance problem that this commit tried to work-around
could not be reproduced. It also makes the wait condition more
complicated then it should be. Therefore remove the double-check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I've seen i2c recovery reporting long loops of:
[ 1035.887818] i2c i2c-4: SCL is stuck low, exit recovery
[ 1037.999748] i2c i2c-4: SCL is stuck low, exit recovery
[ 1040.111694] i2c i2c-4: SCL is stuck low, exit recovery
...
Add a TWSI software reset which clears the status and
STA,STP,IFLG in SW_TWSI_EOP_TWSI_CTL.
With this the recovery works fine and above message is not seen.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch allows Cadence I2C controller to be selected in systems using Cadence Xtensa processors.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add per-Generation fallback bindings for R-Car SoCs.
This is in keeping with the compatibility string scheme is being adopted
for drivers for Renesas SoCs.
Also, improve readability by listing the rmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that it's not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also:
* Deprecate renesas,i2c-rcar. It seems poorly named as it is only
compatible with R-Car Gen 1. It also appears unused in mainline.
* Add some text to describe per-SoC bindings
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some tracepoints have a registration function that gets enabled when the
tracepoint is enabled. There may be cases that the registraction function
must fail (for example, can't allocate enough memory). In this case, the
tracepoint should also fail to register, otherwise the user would not know
why the tracepoint is not working.
Cc: David Howells <dhowells@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.
The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Both Merrifield TRM and Medfield TRM state:
"Both 7-bit and 10-bit addressing modes are supported."
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
