Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Due to the way busy_bits was handled, we were not doing any flushes if
we didn't previously get an invalidate. Since it's possible to get
flushes without an invalidate first, remove the busy_bits early
return.
So now that we don't have the busy_bits guard anymore we'll need the
origin check for the GTT tracking (we were not doing anything on GTT
flushes due to the GTT check at invalidate()).
As a last detail, since we can get multiple consecutive flushes,
disable FBC before updating it, otherwise intel_fbc_update() will just
keep FBC enabled instead of restarting it.
Notice that this does not fix any of the current IGT tests due to the
fact that we still have a few intel_fbc() calls at points where we
also have the frontbuffer tracking calls: we didn't fully convert to
frontbuffer tracking yet. Once we remove those calls and start relying
only on the frontbuffer tracking infrastructure we'll need this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crystalcove pmic support from Shobhit. Patch series has all acks/r-bs from
other mainainers so ok to pull into drm-next. But I'm cc'ing all other
maintainers as fyi and in case they want to pull it into their trees too
to avoid conflicts.
* tag 'topic/crc-pmic-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
mfd: Add GPIOLIB dependency if INTEL_SOC_PMIC is to be enabled
drm/i915: Backlight control using CRC PMIC based PWM driver
drm/i915: Use the CRC gpio for panel enable/disable
pwm: crc: Add Crystalcove (CRC) PWM driver
mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM
mfd: intel_soc_pmic_crc: Add PWM cell device for Crystalcove PMIC
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal
gpiolib: Add support for removing registered consumer lookup table
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we both set mode->private_flags to some value and also use
the pipe_config quirk. But since the pipe_config quirk isn't tied to
the lifetime of the mode object we need to check both.
Simplify this by only using mode.private_flags and stop using the
INHERITED_MODE quirk. Also for clarity add an explicit #define for
that driver priavete mode flag.
By using crtc_state->mode_changed we can also remove the recalc local
variable.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can only fail because of a bug in the code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Squash in follow-up to also remove start_vbl_count from
intel_crtc->atomic and put it into the intel_crtc directly - it's not
precomputed state.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous commit converted hw readout to atomic, all the new_*
members were used for restoring the old state, but with the
conversion of suspend to atomic there's no use left for them.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All non-primary planes get disabled during hw readout,
this reduces complexity and means not having to do some plane
visibility checks during the first commit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing depends on this outside initial hw readout, so keep this
struct on the stack instead.
Changes since v1:
- Remove unrelated changes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's not much point for calculating the changes for the old
state. Instead just disable all scalers when disabling. It's
probably good enough to just disable the crtc_scaler, but just in
case there's a bug disable all scalers.
This means intel_atomic_setup_scalers is only called in the crtc
check function now, so all the transitional code can be removed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since flush actually means invalidate + flush we need to force psr
exit on PSR flush.
On Core platforms there is no way to disable hw tracking and
do the pure sw tracking so we simulate it by fully disable psr and
reschedule a enable back.
So a good idea is to minimize sequential disable/enable in cases we
know that HW tracking like when flush has been originated by a flip.
Also flip had just invalidated it already.
It also uses origin to minimize the a bit the amount of
disable/enabled, mainly when flip already had invalidated.
With this patch in place it is possible to do a flush on dirty areas
properly in a following patch.
v2: Remove duplicated exit on HSW+Sprites as pointed out by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be useful to PSR and FBC once we start making
dirty fb calls to also flush frontbuffer.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Depending on the platform the port clock fed to the pipe can be the PLL's
post-divided fast clock rate or a /5 divided version of it. To make this
more obvious across the platforms calculate this port clock along with
the rest of the PLL parameters.
This is also needed by the next patch where we can reuse the CHV helper
for the BXT PLL HW readout code; so export the corresponding helper.
While at it also add a more descriptive name to the helpers and a
comment explaining what's being calculated.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The frontbuffer code gives us accurate information about activity,
let's use it. Again this should avoid unecessary updates when multiple
screens are on.
Also realign function paramaters, I couldn't resist that bit of OCD.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The current/old frontbuffer might still have gpu frontbuffer rendering
pending. But once flipped it won't have the corresponding frontbuffer
bits any more and hence the request retire function won't ever clear
the corresponding busy bits. The async flip tracking (with the
flip_prepare and flip_complete functions) already does this, but
somehow I've forgotten to do this for synchronous flips.
Note that we don't track outstanding rendering of the new framebuffer
with busy_bits since all our plane update code waits for previous
rendering to complete before displaying a new buffer. Hence a new
buffer will never be busy.
v2: Drop the spurious inline Ville spotted.
v3: Don't touch flip_bits in the synchronsou frontbuffer_flip
function, noticed by Paulo.
v4: Remove one more inline that slipped through (Paulo).
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testcase: igt/kms_frontbuffer_tracking/fbc-modesetfrombusy
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch doesn't have any functional change, but organize fruntbuffer
invalidate and busy by removing unecesarry signature argument for ring.
It was unsed on mark_fb_busy and only used on fb_obj_invalidate for the
same ORIGIN_CS usage. So let's clean it a bit
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By making color key atomic there are no more transitional helpers.
The plane check function will reject the color key when a scaler is
active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the initial state, and add a quirk to force add all planes
to crtc_state->plane_mask during initial commit. This will disable
all planes during the initial modeset.
The initial plane quirk is temporary, and will go away when hardware
readout is fully atomic, and the watermark updates in intel_sprite.c
are removed.
Changes since v1:
- Unset state->visible on !primary planes.
- Do not rely on the plane->crtc pointer in intel_atomic_plane,
instead assume planes are invisible until modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is probably intended to be be done during vblank evasion.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The idea was good, but planes can have a fb even though
they're disabled. This makes the force argument useless
and always true, because only the commit function updates
state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By passing crtc_state to the check_plane functions a lot of duplicated
code can be removed. There are still some transitional helper calls,
they will be removed later.
Changes since v1:
- Revert state->visible changes.
- Use plane->state->crtc instead of plane->crtc.
- Use drm_atomic_get_existing_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes it easier to verify that no changes are done when
calling this from crtc instead.
Changes since v1:
- Make intel_wm_need_update static and always check it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of a whole lot of ternary operators and assign the index
in scaler_id, instead of the id. They're the same thing.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit has two main advantages: simplify intel_fbc_update()
and deduplicate the strings.
v2:
- Rebase due to changes on P1.
- set_no_fbc_reason() can now return void (Chris).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently intel_gen4_compute_page_offset() simply picks the closest
page boundary below the linear offset. That however may not be suitably
aligned to satisfy any hardware specific restrictions. So let's make
sure the page boundary we choose is properly aligned.
Also to play it a bit safer lets split the remaining linear offset into
x and y values instead of just x. This should make no difference for
most platforms since we convert the x and y offsets back into a linear
offset before feeding them to the hardware. HSW+ are different however
and use x and y offsets even with linear buffers, so they might have
trouble if either the x or y get too big.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.
Seems it introduces regressions for 3 different reasons, oh boy..
In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.
In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.
In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.
It's better to fix those issues first, and then commit this patch,
so do that temporarily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
