[ Upstream commit 0b74e40a4e ]
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa86fc2e2 ]
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5cdcdc66 ]
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: 23edc168bd ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e1970 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c9cb4094c ]
The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8a5b272fbf ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06c5fe9b12 upstream
The MBA software controller (mba_sc) is a feedback loop which
periodically reads MBM counters and tries to restrict the bandwidth
below a user-specified value. It tags along the MBM counter overflow
handler to do the updates with 1s interval in mbm_update() and
update_mba_bw().
The purpose of mbm_update() is to periodically read the MBM counters to
make sure that the hardware counter doesn't wrap around more than once
between user samplings. mbm_update() calls __mon_event_count() for local
bandwidth updating when mba_sc is not enabled, but calls mbm_bw_count()
instead when mba_sc is enabled. __mon_event_count() will not be called
for local bandwidth updating in MBM counter overflow handler, but it is
still called when reading MBM local bandwidth counter file
'mbm_local_bytes', the call path is as below:
rdtgroup_mondata_show()
mon_event_read()
mon_event_count()
__mon_event_count()
In __mon_event_count(), m->chunks is updated by delta chunks which is
calculated from previous MSR value (m->prev_msr) and current MSR value.
When mba_sc is enabled, m->chunks is also updated in mbm_update() by
mistake by the delta chunks which is calculated from m->prev_bw_msr
instead of m->prev_msr. But m->chunks is not used in update_mba_bw() in
the mba_sc feedback loop.
When reading MBM local bandwidth counter file, m->chunks was changed
unexpectedly by mbm_bw_count(). As a result, the incorrect local
bandwidth counter which calculated from incorrect m->chunks is shown to
the user.
Fix this by removing incorrect m->chunks updating in mbm_bw_count() in
MBM counter overflow handler, and always calling __mon_event_count() in
mbm_update() to make sure that the hardware local bandwidth counter
doesn't wrap around.
Test steps:
# Run workload with aggressive memory bandwidth (e.g., 10 GB/s)
git clone https://github.com/intel/intel-cmt-cat && cd intel-cmt-cat
&& make
./tools/membw/membw -c 0 -b 10000 --read
# Enable MBA software controller
mount -t resctrl resctrl -o mba_MBps /sys/fs/resctrl
# Create control group c1
mkdir /sys/fs/resctrl/c1
# Set MB throttle to 6 GB/s
echo "MB:0=6000;1=6000" > /sys/fs/resctrl/c1/schemata
# Write PID of the workload to tasks file
echo `pidof membw` > /sys/fs/resctrl/c1/tasks
# Read local bytes counters twice with 1s interval, the calculated
# local bandwidth is not as expected (approaching to 6 GB/s):
local_1=`cat /sys/fs/resctrl/c1/mon_data/mon_L3_00/mbm_local_bytes`
sleep 1
local_2=`cat /sys/fs/resctrl/c1/mon_data/mon_L3_00/mbm_local_bytes`
echo "local b/w (bytes/s):" `expr $local_2 - $local_1`
Before fix:
local b/w (bytes/s): 11076796416
After fix:
local b/w (bytes/s): 5465014272
Fixes: ba0f26d852 (x86/intel_rdt/mba_sc: Prepare for feedback loop)
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/1607063279-19437-1-git-send-email-xiaochen.shen@intel.com
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 758c9373d8 upstream.
membarrier() does not explicitly sync_core() remote CPUs; instead, it
relies on the assumption that an IPI will result in a core sync. On x86,
this may be true in practice, but it's not architecturally reliable. In
particular, the SDM and APM do not appear to guarantee that interrupt
delivery is serializing. While IRET does serialize, IPI return can
schedule, thereby switching to another task in the same mm that was
sleeping in a syscall. The new task could then SYSRET back to usermode
without ever executing IRET.
Make this more robust by explicitly calling sync_core_before_usermode()
on remote cores. (This also helps people who search the kernel tree for
instances of sync_core() and sync_core_before_usermode() -- one might be
surprised that the core membarrier code doesn't currently show up in a
such a search.)
Fixes: 70216e18e5 ("membarrier: Provide core serializing command, *_SYNC_CORE")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/776b448d5f7bd6b12690707f5ed67bcda7f1d427.1607058304.git.luto@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9110e2f263.
This commit is not suitable for 5.4-stable because the openat2 system
call does not exist in v5.4.
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34c0f6f269 upstream.
Commit cae7ed3c2c ("KVM: x86: Refactor the MMIO SPTE generation handling")
cleaned up the computation of MMIO generation SPTE masks, however it
introduced a bug how the upper part was encoded:
SPTE bits 52-61 were supposed to contain bits 10-19 of the current
generation number, however a missing shift encoded bits 1-10 there instead
(mostly duplicating the lower part of the encoded generation number that
then consisted of bits 1-9).
In the meantime, the upper part was shrunk by one bit and moved by
subsequent commits to become an upper half of the encoded generation number
(bits 9-17 of bits 0-17 encoded in a SPTE).
In addition to the above, commit 56871d444b ("KVM: x86: fix overlap between SPTE_MMIO_MASK and generation")
has changed the SPTE bit range assigned to encode the generation number and
the total number of bits encoded but did not update them in the comment
attached to their defines, nor in the KVM MMU doc.
Let's do it here, too, since it is too trivial thing to warrant a separate
commit.
Fixes: cae7ed3c2c ("KVM: x86: Refactor the MMIO SPTE generation handling")
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <156700708db2a5296c5ed7a8b9ac71f1e9765c85.1607129096.git.maciej.szmigiero@oracle.com>
Cc: stable@vger.kernel.org
[Reorganize macros so that everything is computed from the bit ranges. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 175b8d89fe upstream.
syzbot spotted a potential out-of-bounds shift in the PCM OSS layer
where it calculates the buffer size with the arbitrary shift value
given via an ioctl.
Add a range check for avoiding the undefined behavior.
As the value can be treated by a signed integer, the max shift should
be 30.
Reported-by: syzbot+df7dc146ebdd6435eea3@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209084552.17109-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 862ee699fe upstream.
The console part of sisusbvga is broken vs. printk(). It uses in_atomic()
to detect contexts in which it cannot sleep despite the big fat comment in
preempt.h which says: Do not use in_atomic() in driver code.
in_atomic() does not work on kernels with CONFIG_PREEMPT_COUNT=n which
means that spin/rw_lock held regions are not detected by it.
There is no way to make this work by handing context information through to
the driver and this only can be solved once the core printk infrastructure
supports sleepable console drivers.
Make it depend on BROKEN for now.
Fixes: 1bbb4f2035 ("[PATCH] USB: sisusb[vga] update")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201019101109.603244207@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8010622c86 upstream.
UAS does not share the pessimistic assumption storage is making that
devices cannot deal with WRITE_SAME. A few devices supported by UAS,
are reported to not deal well with WRITE_SAME. Those need a quirk.
Add it to the device that needs it.
Reported-by: David C. Partridge <david.partridge@perdrix.co.uk>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209152639.9195-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4d1ca05b8 upstream.
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1373f1047 upstream.
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dde8ffd0 upstream.
The current channel-map control implementation in USB-audio driver may
lead to an error message like
"control 3:0:0:Playback Channel Map:0: access overflow"
when CONFIG_SND_CTL_VALIDATION is set. It's because the chmap get
callback clears the whole array no matter which count is set, and
rather the false-positive detection.
This patch fixes the problem by clearing only the needed array range
at usb_chmap_ctl_get().
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201211130048.6358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a02f954b upstream.
I got reports that some models of this old scanner need
this when using runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e90cfa813d upstream.
This error path
err_add_pdata:
for (i = 0; i < mod_data.num; i++)
kfree(dum[i]);
can be triggered when not all dum's elements are initialized.
Fix this by initializing all dum's elements to NULL.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/1607063090-3426-1-git-send-email-minhquangbui99@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cd6bc0359 upstream.
If the size of the error log is too big to send via email, and the sending
fails, it wont email any result. This can be confusing for the user who is
waiting for an email on the completion of the tests.
If it fails to send email, then try again without the log file stating that
it failed to send an email. Obviously this will not be of use if the sending
of email failed for some other reasons, but it will at least give the user
some information when it fails for the most common reason.
Cc: stable@vger.kernel.org
Fixes: c2d84ddb33 ("ktest.pl: Add MAIL_COMMAND option to define how to send email")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f58591323 ]
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82ca4c922b ]
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc6596fc72 ]
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba603d9d7b ]
In case error CQE was found while polling TX CQ, the QP is in error
state and all posted WQEs will generate error CQEs without any data
transmitted. Fix it by reopening the channels, via same method used for
TX timeout handling.
In addition add some more info on error CQE and WQE for debug.
Fixes: bd2f631d7c ("net/mlx4_en: Notify user when TX ring in error state")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9e13b6adc ]
This is the 3rd revision of the patch fix for potential null pointer dereference
with lan743x card.
The simpliest way to reproduce: boot with bare lan743x and issue "ethtool ethN"
commant where ethN is the interface with lan743x card. Example:
$ sudo ethtool eth7
dmesg:
[ 103.510336] BUG: kernel NULL pointer dereference, address: 0000000000000340
...
[ 103.510836] RIP: 0010:phy_ethtool_get_wol+0x5/0x30 [libphy]
...
[ 103.511629] Call Trace:
[ 103.511666] lan743x_ethtool_get_wol+0x21/0x40 [lan743x]
[ 103.511724] dev_ethtool+0x1507/0x29d0
[ 103.511769] ? avc_has_extended_perms+0x17f/0x440
[ 103.511820] ? tomoyo_init_request_info+0x84/0x90
[ 103.511870] ? tomoyo_path_number_perm+0x68/0x1e0
[ 103.511919] ? tty_insert_flip_string_fixed_flag+0x82/0xe0
[ 103.511973] ? inet_ioctl+0x187/0x1d0
[ 103.512016] dev_ioctl+0xb5/0x560
[ 103.512055] sock_do_ioctl+0xa0/0x140
[ 103.512098] sock_ioctl+0x2cb/0x3c0
[ 103.512139] __x64_sys_ioctl+0x84/0xc0
[ 103.512183] do_syscall_64+0x33/0x80
[ 103.512224] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 103.512274] RIP: 0033:0x7f54a9cba427
...
Previous versions can be found at:
v1:
initial version
https://lkml.org/lkml/2020/10/28/921
v2:
do not return from lan743x_ethtool_set_wol if netdev->phydev == NULL, just skip
the call of phy_ethtool_set_wol() instead.
https://lkml.org/lkml/2020/10/31/380
v3:
in function lan743x_ethtool_set_wol:
use ternary operator instead of if-else sentence (review by Markus Elfring)
return -ENETDOWN insted of -EIO (review by Andrew Lunn)
Signed-off-by: Sergej Bauer <sbauer@blackbox.su>
Link: https://lore.kernel.org/r/20201101223556.16116-1-sbauer@blackbox.su
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fed91613c9 ]
Add restarting state flag to avoid scheduling another restart task while
such task is already running. Change task name from watchdog_task to
restart_task to better fit the task role.
Fixes: 1e338db56e ("mlx4_en: Fix a race at restart task")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 299bcb55ec ]
When cwnd is not a multiple of the TSO skb size of N*MSS, we can get
into persistent scenarios where we have the following sequence:
(1) ACK for full-sized skb of N*MSS arrives
-> tcp_write_xmit() transmit full-sized skb with N*MSS
-> move pacing release time forward
-> exit tcp_write_xmit() because pacing time is in the future
(2) TSQ callback or TCP internal pacing timer fires
-> try to transmit next skb, but TSO deferral finds remainder of
available cwnd is not big enough to trigger an immediate send
now, so we defer sending until the next ACK.
(3) repeat...
So we can get into a case where we never mark ourselves as
cwnd-limited for many seconds at a time, even with
bulk/infinite-backlog senders, because:
o In case (1) above, every time in tcp_write_xmit() we have enough
cwnd to send a full-sized skb, we are not fully using the cwnd
(because cwnd is not a multiple of the TSO skb size). So every time we
send data, we are not cwnd limited, and so in the cwnd-limited
tracking code in tcp_cwnd_validate() we mark ourselves as not
cwnd-limited.
o In case (2) above, every time in tcp_write_xmit() that we try to
transmit the "remainder" of the cwnd but defer, we set the local
variable is_cwnd_limited to true, but we do not send any packets, so
sent_pkts is zero, so we don't call the cwnd-limited logic to update
tp->is_cwnd_limited.
Fixes: ca8a226343 ("tcp: make cwnd-limited checks measurement-based, and gentler")
Reported-by: Ingemar Johansson <ingemar.s.johansson@ericsson.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201209035759.1225145-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72d05c00d7 ]
Before commit a337531b94 ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
small tcp_rmem[1] values were overridden by tcp_fixup_rcvbuf() to accommodate various MSS.
This is no longer the case, and Hazem Mohamed Abuelfotoh reported
that DRS would not work for MTU 9000 endpoints receiving regular (1500 bytes) frames.
Root cause is that tcp_init_buffer_space() uses tp->rcv_wnd for upper limit
of rcvq_space.space computation, while it can select later a smaller
value for tp->rcv_ssthresh and tp->window_clamp.
ss -temoi on receiver would show :
skmem:(r0,rb131072,t0,tb46080,f0,w0,o0,bl0,d0) rcv_space:62496 rcv_ssthresh:56596
This means that TCP can not increase its window in tcp_grow_window(),
and that DRS can never kick.
Fix this by making sure that rcvq_space.space is not bigger than number of bytes
that can be held in TCP receive queue.
People unable/unwilling to change their kernel can work around this issue by
selecting a bigger tcp_rmem[1] value as in :
echo "4096 196608 6291456" >/proc/sys/net/ipv4/tcp_rmem
Based on an initial report and patch from Hazem Mohamed Abuelfotoh
https://lore.kernel.org/netdev/20201204180622.14285-1-abuehaze@amazon.com/
Fixes: a337531b94 ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Fixes: 041a14d267 ("tcp: start receiver buffer autotuning sooner")
Reported-by: Hazem Mohamed Abuelfotoh <abuehaze@amazon.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 851d0a73c9 ]
When enabling multicast snooping, bridge module deadlocks on multicast_lock
if 1) IPv6 is enabled, and 2) there is an existing querier on the same L2
network.
The deadlock was caused by the following sequence: While holding the lock,
br_multicast_open calls br_multicast_join_snoopers, which eventually causes
IP stack to (attempt to) send out a Listener Report (in igmp6_join_group).
Since the destination Ethernet address is a multicast address, br_dev_xmit
feeds the packet back to the bridge via br_multicast_rcv, which in turn
calls br_multicast_add_group, which then deadlocks on multicast_lock.
The fix is to move the call br_multicast_join_snoopers outside of the
critical section. This works since br_multicast_join_snoopers only deals
with IP and does not modify any multicast data structures of the bridge,
so there's no need to hold the lock.
Steps to reproduce:
1. sysctl net.ipv6.conf.all.force_mld_version=1
2. have another querier
3. ip link set dev bridge type bridge mcast_snooping 0 && \
ip link set dev bridge type bridge mcast_snooping 1 < deadlock >
A typical call trace looks like the following:
[ 936.251495] _raw_spin_lock+0x5c/0x68
[ 936.255221] br_multicast_add_group+0x40/0x170 [bridge]
[ 936.260491] br_multicast_rcv+0x7ac/0xe30 [bridge]
[ 936.265322] br_dev_xmit+0x140/0x368 [bridge]
[ 936.269689] dev_hard_start_xmit+0x94/0x158
[ 936.273876] __dev_queue_xmit+0x5ac/0x7f8
[ 936.277890] dev_queue_xmit+0x10/0x18
[ 936.281563] neigh_resolve_output+0xec/0x198
[ 936.285845] ip6_finish_output2+0x240/0x710
[ 936.290039] __ip6_finish_output+0x130/0x170
[ 936.294318] ip6_output+0x6c/0x1c8
[ 936.297731] NF_HOOK.constprop.0+0xd8/0xe8
[ 936.301834] igmp6_send+0x358/0x558
[ 936.305326] igmp6_join_group.part.0+0x30/0xf0
[ 936.309774] igmp6_group_added+0xfc/0x110
[ 936.313787] __ipv6_dev_mc_inc+0x1a4/0x290
[ 936.317885] ipv6_dev_mc_inc+0x10/0x18
[ 936.321677] br_multicast_open+0xbc/0x110 [bridge]
[ 936.326506] br_multicast_toggle+0xec/0x140 [bridge]
Fixes: 4effd28c12 ("bridge: join all-snoopers multicast address")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20201204235628.50653-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb96b686fc ]
Noticed some inconsistencies in packet statistics reporting.
This patch adds the missing Tx packet counter registers to
ethtool reporting and fixes the information strings for a
few of them.
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204171505.21389-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10c678bd0a ]
Guillaume noticed that: for segments udp_queue_rcv_one_skb() returns the
proto, and it should pass "ret" unmodified to ip_protocol_deliver_rcu().
Otherwize, with a negtive value passed, it will underflow inet_protos.
This can be reproduced with IPIP FOU:
# ip fou add port 5555 ipproto 4
# ethtool -K eth1 rx-gro-list on
Fixes: cf329aa42b ("udp: cope with UDP GRO packet misdirection")
Reported-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61f54de2e9 ]
hclge_dbg_reg_info[] is defined as an array of packed structure
accidentally. However, this array contains pointers, which are
no longer aligned naturally, and cannot be relocated on PPC64.
Hence, when compile-testing this driver on PPC64 with
CONFIG_RELOCATABLE=y (e.g. PowerPC allyesconfig), there will be
some warnings.
Since each field in structure hclge_qos_pri_map_cmd and
hclge_dbg_bitmap_cmd is type u8, the pragma packed is unnecessary
for these two structures as well, so remove the pragma packed in
hclge_debugfs.h to fix this issue, and this increases
hclge_dbg_reg_info[] by 4 bytes per entry.
Fixes: a582b78dfc ("net: hns3: code optimization for debugfs related to "dump reg"")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 205704c618 ]
Depending on the order of the routes to fe80::/64 are installed on the
VRF table, the NS for the source link-local address of the originator
might be sent to the wrong interface.
This patch ensures that packets with link-local addr source is doing a
lookup with the orig_iif when the destination addr indicates that it
is strict.
Add the reproducer as a use case in self test script fcnal-test.sh.
Fixes: b4869aa2f8 ("net: vrf: ipv6 support for local traffic to local addresses")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201204030604.18828-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee4f52a8de ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f8ed289fab ("bridge: vlan: use br_vlan_(get|put)_master to deal with refcounts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/1607071737-33875-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b410f04eb5 ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: d15662682d ("ipv4: Allow ipv6 gateway with ipv4 routes")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/1607071695-33740-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0032ce0f85 upstream.
ptrace_get_syscall_info() is potentially copying uninitialized stack
memory to userspace, since the compiler may leave a 3-byte hole near the
beginning of `info`. Fix it by adding a padding field to `struct
ptrace_syscall_info`.
Fixes: 201766a20e ("ptrace: add PTRACE_GET_SYSCALL_INFO request")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200801152044.230416-1-yepeilin.cs@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3347acc6fc upstream.
Commit 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive") neglected to copy barrier_data() from
compiler-gcc.h into compiler-clang.h.
The definition in compiler-gcc.h was really to work around clang's more
aggressive optimization, so this broke barrier_data() on clang, and
consequently memzero_explicit() as well.
For example, this results in at least the memzero_explicit() call in
lib/crypto/sha256.c:sha256_transform() being optimized away by clang.
Fix this by moving the definition of barrier_data() into compiler.h.
Also move the gcc/clang definition of barrier() into compiler.h,
__memory_barrier() is icc-specific (and barrier() is already defined
using it in compiler-intel.h) and doesn't belong in compiler.h.
[rdunlap@infradead.org: fix ALPHA builds when SMP is not enabled]
Link: https://lkml.kernel.org/r/20201101231835.4589-1-rdunlap@infradead.org
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201014212631.207844-1-nivedita@alum.mit.edu
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[nd: backport to account for missing
commit e506ea4512 ("compiler.h: Split {READ,WRITE}_ONCE definitions out into rwonce.h")
commit d08b9f0ca6 ("scs: Add support for Clang's Shadow Call Stack (SCS)")]
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e91d8d7823 upstream.
While I was doing zram testing, I found sometimes decompression failed
since the compression buffer was corrupted. With investigation, I found
below commit calls cond_resched unconditionally so it could make a
problem in atomic context if the task is reschedule.
BUG: sleeping function called from invalid context at mm/vmalloc.c:108
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 946, name: memhog
3 locks held by memhog/946:
#0: ffff9d01d4b193e8 (&mm->mmap_lock#2){++++}-{4:4}, at: __mm_populate+0x103/0x160
#1: ffffffffa3d53de0 (fs_reclaim){+.+.}-{0:0}, at: __alloc_pages_slowpath.constprop.0+0xa98/0x1160
#2: ffff9d01d56b8110 (&zspage->lock){.+.+}-{3:3}, at: zs_map_object+0x8e/0x1f0
CPU: 0 PID: 946 Comm: memhog Not tainted 5.9.3-00011-gc5bfc0287345-dirty #316
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
Call Trace:
unmap_kernel_range_noflush+0x2eb/0x350
unmap_kernel_range+0x14/0x30
zs_unmap_object+0xd5/0xe0
zram_bvec_rw.isra.0+0x38c/0x8e0
zram_rw_page+0x90/0x101
bdev_write_page+0x92/0xe0
__swap_writepage+0x94/0x4a0
pageout+0xe3/0x3a0
shrink_page_list+0xb94/0xd60
shrink_inactive_list+0x158/0x460
We can fix this by removing the ZSMALLOC_PGTABLE_MAPPING feature (which
contains the offending calling code) from zsmalloc.
Even though this option showed some amount improvement(e.g., 30%) in
some arm32 platforms, it has been headache to maintain since it have
abused APIs[1](e.g., unmap_kernel_range in atomic context).
Since we are approaching to deprecate 32bit machines and already made
the config option available for only builtin build since v5.8, lastly it
has been not default option in zsmalloc, it's time to drop the option
for better maintenance.
[1] http://lore.kernel.org/linux-mm/20201105170249.387069-1-minchan@kernel.org
Fixes: e47110e905 ("mm/vunmap: add cond_resched() in vunmap_pmd_range")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Harish Sriram <harish@linux.ibm.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201117202916.GA3856507@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190113b4c6 upstream.
Prarit reported that depending on the affinity setting the
' irq $N: Affinity broken due to vector space exhaustion.'
message is showing up in dmesg, but the vector space on the CPUs in the
affinity mask is definitely not exhausted.
Shung-Hsi provided traces and analysis which pinpoints the problem:
The ordering of trying to assign an interrupt vector in
assign_irq_vector_any_locked() is simply wrong if the interrupt data has a
valid node assigned. It does:
1) Try the intersection of affinity mask and node mask
2) Try the node mask
3) Try the full affinity mask
4) Try the full online mask
Obviously #2 and #3 are in the wrong order as the requested affinity
mask has to take precedence.
In the observed cases #1 failed because the affinity mask did not contain
CPUs from node 0. That made it allocate a vector from node 0, thereby
breaking affinity and emitting the misleading message.
Revert the order of #2 and #3 so the full affinity mask without the node
intersection is tried before actually affinity is broken.
If no node is assigned then only the full affinity mask and if that fails
the full online mask is tried.
Fixes: d6ffc6ac83 ("x86/vector: Respect affinity mask in irq descriptor")
Reported-by: Prarit Bhargava <prarit@redhat.com>
Reported-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87ft4djtyp.fsf@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a493d1ca1a upstream.
sync_core_before_usermode() had an incorrect optimization. If the kernel
returns from an interrupt, it can get to usermode without IRET. It just has
to schedule to a different task in the same mm and do SYSRET. Fortunately,
there were no callers of sync_core_before_usermode() that could have had
in_irq() or in_nmi() equal to true, because it's only ever called from the
scheduler.
While at it, clarify a related comment.
Fixes: 70216e18e5 ("membarrier: Provide core serializing command, *_SYNC_CORE")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/5afc7632be1422f91eaf7611aaaa1b5b8580a086.1607058304.git.luto@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29ac40cbed upstream.
The PAT bit is in different locations for 4k and 2M/1G page table
entries.
Add a definition for _PAGE_LARGE_CACHE_MASK to represent the three
caching bits (PWT, PCD, PAT), similar to _PAGE_CACHE_MASK for 4k pages,
and use it in the definition of PMD_FLAGS_DEC_WP to get the correct PAT
index for write-protected pages.
Fixes: 6ebcb06071 ("x86/mm: Add support to encrypt the kernel in-place")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20201111160946.147341-1-nivedita@alum.mit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeaf06af6f upstream.
My patch caused kernel Oopses and delays in boot. Revert it.
The problem was that I moved the "mem->dma = paddr;" before the call to
be_fill_queue(). But the first thing that the be_fill_queue() function
does is memset the whole struct to zero which overwrites the assignment.
Link: https://lore.kernel.org/r/X8jXkt6eThjyVP1v@mwanda
Fixes: 38b2db564d ("scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()")
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d6366e9d upstream.
When we try to visit the pagemap of a tagged userspace pointer, we find
that the start_vaddr is not correct because of the tag.
To fix it, we should untag the userspace pointers in pagemap_read().
I tested with 5.10-rc4 and the issue remains.
Explanation from Catalin in [1]:
"Arguably, that's a user-space bug since tagged file offsets were never
supported. In this case it's not even a tag at bit 56 as per the arm64
tagged address ABI but rather down to bit 47. You could say that the
problem is caused by the C library (malloc()) or whoever created the
tagged vaddr and passed it to this function. It's not a kernel
regression as we've never supported it.
Now, pagemap is a special case where the offset is usually not
generated as a classic file offset but rather derived by shifting a
user virtual address. I guess we can make a concession for pagemap
(only) and allow such offset with the tag at bit (56 - PAGE_SHIFT + 3)"
My test code is based on [2]:
A userspace pointer which has been tagged by 0xb4: 0xb400007662f541c8
userspace program:
uint64 OsLayer::VirtualToPhysical(void *vaddr) {
uint64 frame, paddr, pfnmask, pagemask;
int pagesize = sysconf(_SC_PAGESIZE);
off64_t off = ((uintptr_t)vaddr) / pagesize * 8; // off = 0xb400007662f541c8 / pagesize * 8 = 0x5a00003b317aa0
int fd = open(kPagemapPath, O_RDONLY);
...
if (lseek64(fd, off, SEEK_SET) != off || read(fd, &frame, 8) != 8) {
int err = errno;
string errtxt = ErrorString(err);
if (fd >= 0)
close(fd);
return 0;
}
...
}
kernel fs/proc/task_mmu.c:
static ssize_t pagemap_read(struct file *file, char __user *buf,
size_t count, loff_t *ppos)
{
...
src = *ppos;
svpfn = src / PM_ENTRY_BYTES; // svpfn == 0xb400007662f54
start_vaddr = svpfn << PAGE_SHIFT; // start_vaddr == 0xb400007662f54000
end_vaddr = mm->task_size;
/* watch out for wraparound */
// svpfn == 0xb400007662f54
// (mm->task_size >> PAGE) == 0x8000000
if (svpfn > mm->task_size >> PAGE_SHIFT) // the condition is true because of the tag 0xb4
start_vaddr = end_vaddr;
ret = 0;
while (count && (start_vaddr < end_vaddr)) { // we cannot visit correct entry because start_vaddr is set to end_vaddr
int len;
unsigned long end;
...
}
...
}
[1] https://lore.kernel.org/patchwork/patch/1343258/
[2] https://github.com/stressapptest/stressapptest/blob/master/src/os.cc#L158
Link: https://lkml.kernel.org/r/20201204024347.8295-1-miles.chen@mediatek.com
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Song Bao Hua (Barry Song) <song.bao.hua@hisilicon.com>
Cc: <stable@vger.kernel.org> [5.4-]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14dc3983b5 upstream.
genksyms does not know or care about the _Static_assert() built-in, and
sometimes falls back to ignoring the later symbols, which causes
undefined behavior such as
WARNING: modpost: EXPORT symbol "ethtool_set_ethtool_phy_ops" [vmlinux] version generation failed, symbol will not be versioned.
ld: net/ethtool/common.o: relocation R_AARCH64_ABS32 against `__crc_ethtool_set_ethtool_phy_ops' can not be used when making a shared object
net/ethtool/common.o:(_ftrace_annotated_branch+0x0): dangerous relocation: unsupported relocation
Redefine static_assert for genksyms to avoid that.
Link: https://lkml.kernel.org/r/20201203230955.1482058-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Cc: Marco Elver <elver@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6cbe49be6 upstream.
This patch fixes the slice count computation algorithm
for calculating the slice count based on Peak pixel rate
and the max slice width allowed on the DSC engines.
We need to ensure slice count > min slice count req
as per DP spec based on peak pixel rate and that it is
greater than min slice count based on the max slice width
advertised by DPCD. So use max of these two.
In the prev patch we were using min of these 2 causing it
to violate the max slice width limitation causing a blank
screen on 8K@60.
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204205804.25225-1-manasi.d.navare@intel.com
(cherry picked from commit d371d6ea92)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko