When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
xhci_unregister_pci() is called in xhci_hcd_init().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
of_gpio_simple_xlate() has an off-by-one bug where it checks to see if
args[0] is > ngpio instead of >=. args[0] must always be less than
ngpio because it is a zero-based enumeration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
[grant.likely: beef up commit text]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move rt2x00rfkill_register(rt2x00dev) to rt2x00lib_probe_dev
function. It fixes of starting rfkill_poll function at the
right time if sets hard rfkill block and reboot. rt2x00mac_rfkill_poll
should be starting before bringing up the wireless interface.
Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
CC: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial rename to stop the build system complaining that we're
referencing things we shouldn't be.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=45TQ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
We've only computed whether we need to fall back to 6bpc due to dp
link bandwidth constrains in mode_valid, but not mode_fixup. Under
various circumstances X likes to create new modes which then lack
proper 6bpc flags (if required), resulting in mode_fixup failures and
ultimately black screens.
Chris Wilson pointed out that we still get things wrong for bpp > 24,
but that should be fixed in another patch (and it'll be easier because
this patch consolidates the logic).
The likely culprit for this regression is
commit 3d794f87238f74d80e78a7611c7fbde8a54c85c2
Author: Keith Packard <keithp@keithp.com>
Date: Wed Jan 25 08:16:25 2012 -0800
drm/i915: Force explicit bpp selection for intel_dp_link_required
v2: Fix indentation and tune down the too bold claim that this should
fix the world. Both noticed by Chris Wilson.
v3: Try to really git add things.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48170
Cc: stable@kernel.org
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Image on Z11m cards was totally garbled due to wrong memory being
selected. Add a special handling for Z11m cards. Tested on PCIe Z11 and
Z11m cards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gpio_request fails, we need to free all allocated resources.
Current code uses wrong array index to access gpio_data array.
So current code actually frees gpio_data[i].gpio by j times.
This patch moves the error handling code to err_out and thus improves
readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m68k doesn't have memblock_reserve, which causes a build failure
with allmodconfig. Make PERSISTENT_RAM and RAM_CONSOLE depend on
HAVE_MEMBLOCK.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c client data set is of type struct indio_dev pointer and hence the
pointer returned from i2c_get_clientdata() should be assigned to
an object of type struct indio_dev and not to an object of type
struct ak8975_data.
Also in ak8975_probe() client data should be set first
before calling ak8975_setup() as it references the client data.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
CC: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not sure what triggered the change in behavior, but seems to
result in recursively acquiring a mutex and hanging on boot. But
omap_drm_init() seems a much more sane place to register the
driver for the DMM sub-device.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a memory leak in zsmalloc where the first
subpage of each zspage is leaked when the zspage is freed.
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I already fixed the other similar for loop in this file. I'm not sure
how I missed this one. We use seg_no+1 inside the loop so we can't go
right up to the end of the loop.
Also if we don't break out of the loop then we end up past the end of
the array, but with this fix we end up on the last element.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added Rupesh Gujare to MAINTAINERS file and contact in TODO file
for ozwpan driver.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid "Bad LUN" and "Bad target number" message by setting the supported
max_lun and max_id for the scsi host
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtsx_transport.c (rtsx_transfer_sglist_adma_partial):
pointer struct scatterlist *sg, which is mapped in dma_map_sg,
is used as an iterator in later transfer operation. It is corrupted and
passed to dma_unmap_sg, thus causing fatal unmap of some erroneous address.
Fix it by duplicating *sg_ptr for iterating.
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the we don't copy too much memory. This comes from a
copy_from_user() in the ioctl.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If, in drivers/staging/media/as102/as102_fw.c::as102_fw_upload(), the call
cmd_buf = kzalloc(MAX_FW_PKT_SIZE, GFP_KERNEL);
should fail and return NULL so that we jump to the 'error:' label,
then we'll end up calling 'release_firmware(firmware);' with
'firmware' still uninitialized - not good.
The easy fix is to just initialize 'firmware' to NULL when we declare
it, since release_firmware() deals gracefully with being passed NULL
pointers.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The just-merged ramster staging driver was dependent on a cleanup patch in
cleancache, so was marked CONFIG_BROKEN until that patch could be
merged. That cleancache patch is now merged (and the correct SHA of the
cleancache patch is 3167760f83 rather than
the one shown in the comment removed in the patch below).
So remove the CONFIG_BROKEN now and the comment that is no longer true...
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of our errors wasn't negative as intended. Fix this.
(Found by Hillf Danton)
While we are at it turn user causable messages down to dev_dbg level in the
ioctl paths.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't call i2c_enable on resume because it causes a spurious
interrupt.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some r4xx chips have the wrong frev in the
DVOEncoderControl table. It should always be 1
on r4xx. Fixes modesetting on DVO on r4xx chips
with the bad frev.
Reported by twied on #radeon.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since cmdbuf->size and cmdbuf->nbox are from userspace, a large value
would overflow the allocation size, leading to out-of-bounds access.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some architectures require that delays longer than a few
miliseconds are called through mdelay. This was triggered
on ARM randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add pointer and buttonpad properties for v4 hardware.
Also, Jachiet reported that on Asus UX31, right button has no effect.
It turns out v4 has only one button, the right-button effect is
implemented with software when Windows driver is installed, or in
firmware when touchpad is in relative mode. So remove BTN_RIGHT
while at it.
Reported-by: Jachiet Louis <louis@jachiet.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acer VH40 has a Fn key toggling the touchpad on and off, but it's
implemented in system firmware, and the EC chip has to receive
reset command to activate this function. Also when this machine
wakes up after resume, psmouse_reset is necessary to bring the
touchpad back on.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The task handoff notifier leaks task_struct since it never gets freed
after the callback returns NOTIFY_OK, which means it is responsible for
doing so.
It turns out the lowmemorykiller actually doesn't need this notifier at
all. It's used to prevent unnecessary killing by waiting for a thread
to exit as a result of lowmem_shrink(), however, it's possible to do
this in the same way the kernel oom killer works by setting TIF_MEMDIE
and avoid killing if we're still waiting for it to exit.
The kernel oom killer will already automatically set TIF_MEMDIE for
threads that are attempting to allocate memory that have a fatal signal.
The thread selected by lowmem_shrink() will have such a signal after the
lowmemorykiller sends it a SIGKILL, so this won't result in an
unnecessary use of memory reserves for the thread to exit.
This has the added benefit that we don't have to rely on
CONFIG_PROFILING to prevent needlessly killing tasks.
Reported-by: Werner Landgraf <w.landgraf@ru.ru>
Cc: stable@vger.kernel.org
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1538) causes uhci_hub_status_data() to return a nonzero
value when any port is undergoing a resume transition while the root
hub is suspended. This will allow usbcore to handle races between
root-hub suspend and port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1537) adds a bit-array to ehci-hcd for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when ehci_hub_status_data() is called, the routine will return
a nonzero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1533) fixes a race between root-hub suspend and remote
wakeup. If a wakeup event occurs while a root hub is suspending, it
might not cause the suspend to fail. Although the host controller
drivers check for pending wakeup events at the start of their
bus_suspend routines, they generally do not check for wakeup events
while the routines are running.
In addition, if a wakeup event occurs any time after khubd is frozen
and before the root hub is fully suspended, it might not cause a
system sleep transition to fail. For example, the host controller
drivers do not fail root-hub suspends when a connect-change event is
pending.
To fix both these issues, this patch causes hcd_bus_suspend() to query
the controller driver's hub_status_data method after a root hub is
suspended, if the root hub is enabled for wakeup. Any pending status
changes will count as wakeup events, causing the root hub to be
resumed and the overall suspend to fail with -EBUSY.
A significant point is that not all events are reflected immediately
in the status bits. Both EHCI and UHCI controllers notify the CPU
when remote wakeup begins on a port, but the port's suspend-change
status bit doesn't get set until after the port has completed the
transition out of the suspend state, some 25 milliseconds later.
Consequently, the patch will interpret any nonzero return value from
hub_status_data as indicating a pending event, even if none of the
status bits are set in the data buffer. Follow-up patches make the
necessary changes to ehci-hcd and uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just add new device id. 3G works fine, LTE not tested.
Signed-off-by: Anton Samokhvalov <pg83@yandex.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues here, one is that the device is generating
spurious very fast modem status line changes somewhere:
CTS becomes high then low 18µs later:
[121226.924373] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=6
[121226.924378] ftdi_process_packet: status=10 prev=00 diff=10
[121226.924382] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=7
(wake_up_interruptible is called)
[121226.924391] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=7
[121226.924394] ftdi_process_packet: status=00 prev=10 diff=10
[121226.924397] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=8
(wake_up_interruptible is called)
This wakes up the task in TIOCMIWAIT:
[121226.924405] ftdi_ioctl: 19451 rng=0->0 dsr=10->10 dcd=0->0 cts=6->8
(wait from 20:51:46 returns and observes both changes)
Which then calls TIOCMIWAIT again:
20:51:46.400239 ioctl(3, TIOCMIWAIT, 0x20) = 0
22:11:09.441818 ioctl(3, TIOCMGET, [TIOCM_DTR|TIOCM_RTS]) = 0
22:11:09.442812 ioctl(3, TIOCMIWAIT, 0x20) = -1 EIO (Input/output error)
(the second wake_up_interruptible takes effect and an I/O error occurs)
The other issue is that TIOCMIWAIT will wait forever (unless the task is
interrupted) if the device is removed.
This change removes the -EIO return that occurs if the counts don't
appear to have changed. Multiple counts may have been processed as
one or the waiting task may have started waiting after recording the
current count.
It adds a bool to indicate that the device has been removed so that
TIOCMIWAIT doesn't wait forever, and wakes up any tasks so that they can
return -EIO.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling of TIOCMIWAIT was changed by commit 1d749f9afa
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
FTDI_STATUS_B0_MASK does not indicate the changed modem status lines,
it indicates the value of the current modem status lines. An xor is
still required to determine which lines have changed.
The count was only being incremented if the line was high. The only
reason TIOCMIWAIT still worked was because the status packet is
repeated every 1ms, so the count was always changing. The wakeup
itself still ran based on the status lines changing.
This change fixes handling of updates to the modem status lines and
allows multiple processes to use TIOCMIWAIT concurrently.
Tested with two processes waiting on different status lines being
toggled independently.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1536) fixes a bug in the USB serial core. Unloading and
reloading a serial driver while a serial device is plugged in causes
errors because of the code in usb_serial_disconnect() that tries to
make sure the port_remove method is called. With the new order of
driver registration introduced in the 3.4 kernel, this is definitely
not the right thing to do (if indeed it ever was).
The patch removes that whole section code, along with the mechanism
for keeping track of each port's registration state, which is no
longer needed. The driver core can handle all that stuff for us.
Note: This has been tested only with one or two USB serial drivers.
In theory, other drivers might still run into trouble. But if they
do, it will be the fault of the drivers, not of this patch -- that is,
the drivers will need to be fixed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right idProduct for Metrologic Bar Code Scanner
in Uni-Directional Serial Emulation mode is 0x0700.
Also rename idProduct for Bi-Directional mode to be a bit more informative.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DTR/RTS should only be raised when changing baudrate from B0 and not on
any baud rate change (> B0).
Reported-by: Søren Holm <sgh@sgh.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes:
note: expected ‘struct ida *’ but argument is of type ‘struct idr *’
warning: passing argument 1 of ‘ida_pre_get’ from incompatible pointer type
Reported-by: Arnd Bergman <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
soc_lock is already initialized by DEFINE_SPINLOCK.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the rate-control indexing is incorrectly set up, mac80211 issues
a warning and returns NULL from the call to ieee80211_get_tx_rate().
When this happens, avoid a NULL pointer dereference.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before the switch to asynchronous firmware loading (mainline commit b0302ab),
it was necessary to load firmware when initializing the first of the units
in a dual-mac system. After the change, it is necessary to load firmware in
both units.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the case where we are changing from one framebuffer to
another, we need to be sure that there are no pending WAIT_FOR_EVENTs on
the pipe for the current framebuffer before switching. If we disable the
pipe, and then try to execute a WAIT_FOR_EVENT it will block
indefinitely and cause a GPU hang.
We attempted to fix this in commit 85345517fe
(drm/i915: Retire any pending operations on the old scanout when switching)
for the case of mode switching, but this leaves the condition where we
are switching off the pipe vulnerable.
There still remains the race condition were a display may be unplugged,
switched off by the core, a uevent sent to notify the DDX and the DDX
may issue a WAIT_FOR_EVENT before it processes the uevent. This window
does not exist if the pipe is only switched off in response to the
uevent. Time to make sure that is so...
Reported-by: Francis Leblanc <Francis.Leblanc-Lebeau@verint.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45413
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixup spelling in comment, noticed by Eugeni.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The destination color key is always enabled for IVB. Removed
the line that does this.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some configurations produce the following compiler warning:
drivers/hwmon/pmbus/pmbus_core.c: In function 'pmbus_show_boolean':
drivers/hwmon/pmbus/pmbus_core.c:752: warning: 'val' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from pmbus_get_boolean with both val and error return code (val is a
boolean and thus never negative).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47m1.c: In function 'sm_smsc47m1_init':
drivers/hwmon/smsc47m1.c:938: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47m1_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (46 bytes for x86_64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
In some configurations, BUG() does not result in an endless loop but returns
to the caller. This results in the following compiler warning:
drivers/hwmon/acpi_power_meter.c: In function 'show_str':
drivers/hwmon/acpi_power_meter.c:380: warning: 'val' may be used uninitialized in this function
Fix the warning by setting val to an empty string after BUG().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47b397.c: In function 'smsc47b397_init':
drivers/hwmon/smsc47b397.c:385: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47b397_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (64 bytes for x86_64).
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add UART clock quirk for the Kontron COMe-mTT10 module.
The board has previously been called nanoETXexpress-TT, therefore this
is also checked.
As suggested by Darren Hart the comparison in this patch version is
placed after the FRI2 checks to ensure it will also work with possible
upcoming changes to the FRI2 firmware.
This patch follows the patchset submitted by Darren Hart at
commit a46f5533ec.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch (MSI setting) is not enough.
commit e463595fd9
Author: Alexander Stein <alexander.stein@systec-electronic.com>
Date: Mon Jul 4 08:58:31 2011 +0200
pch_uart: Add MSI support
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To enable MSI mode, PCI bus-mastering must be enabled.
This patch enables the setting.
cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround dropped notifications in the iir register. Register reads
coincident with new interrupt notifications sometimes result in this
device clearing the interrupt event without reporting it in the read
data.
The serial core already has a heuristic for determining when a device
has an untrustworthy iir register. In this case when we apriori know
that the iir is faulty use a flag (UPF_BUG_THRE) to bypass the test and
force usage of the background timer.
[stable: 3.3.x]
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Reported-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Tested-by: Nhan H Mai <nhan.h.mai@intel.com>
Tested-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 448ac154c9.
The semantic of UPF_IIR_ONCE is only guaranteed to workaround the race
condition in the kt serial's iir register if the only source of
interrupts is THRE (fifo-empty) events. An modem status event at the
wrong time can again cause an iir read to drop the 'empty' status
leading to a hang. So, revert this in preparation for using the
existing "I don't trust my iir register" workaround in the 8250 core
(UART_BUG_THRE).
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e86ff4a63c.
This tried to enforce the semantics of one interrupt per iir read of the
THRE (transmit-hold empty) status, but events from other sources
(particularly modem status) defeat this guarantee.
This change also broke 8250_pci suspend/resume support as
pciserial_resume_ports() re-runs .init() quirks, but does not run
.exit() quirks in pciserial_suspend_ports() leading to reports like:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:16.3/msi_irqs'
...and a subsequent crash. The mismatch of init/exit at suspend/resume
seems like a bug in its own right.
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the omap serial driver is built as a module, we must
not allow the console driver to be selected, because consoles
can not be loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix omission initialize ulcon in s3c24xx_serial_resetport(),
reset port function in drivers/tty/serial/samsung.c. It has
been happened from commit 0dfb3b41("serial: samsung: merge
all SoC specific port reset functions")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org> [3.3]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A prototype for kmsg records instead of a byte-stream buffer revealed
a couple of missing printk(KERN_CONT ...) uses. Subsequent calls produce
one record per printk() call, while all should have ended up in a single
record.
Instead of:
ACPI: (supports S0 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
hpet0: at MMIO 0xfed00000, IRQs 2 , 8 , 0
It prints:
ACPI: (supports S0
S5
)
ACPI: PCI Interrupt Link [LNKA] (IRQs
5
*10
11
)
hpet0: at MMIO 0xfed00000, IRQs
2
, 8
, 0
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On our custom board, we are using RS485 in half-duplex mode on an AT91SAM9G45.
SER_RS485_RX_DURING_TX is not set as we do not want to receive the data we
transmit (our transceiver will receive transmitted data).
Although the current driver attempts to disable and enable the receiver at the
appropriate points, incoming data is still loaded into the receive register
causing our code to receive the very last byte that was sent once the receiver
is enabled.
I ran this by Atmel support and they wrote: "The issue comes from the fact
that you disable the PDC/DMA Reception and not the USART Reception channel. In
your case, the[n] you will still receive data into the USART_RHR register, and
maybe you [h]ave the overrun flag set. So please disable the USART reception
channel."
The following patch should force the driver to enable/disable the receiver via
RXEN/RXDIS fields of the USART control register. It fixed the issue I was
having.
Signed-off-by: Gabe Siftar <gabe.siftar@getingeusa.com>
[nicolas.ferre@atmel.com: slightly modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow altera_jtag_uart. This fixes a crash if there is a mistake in the DTS.
Signed-off-by: Yuriy Kozlov <ykozlov@ptcusa.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "TTY buffer in tty_port" patchset introduced an opencoded
debug message in the Gigaset tty device if_close() function.
Change it to use the gig_dbg() macro like everywhere else in
the driver.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch does the following
- The pm_runtime_disable is called in the remove not in the error
case of probe.The patch calls the pm_runtime_disable in the error
case.
- Calls pm_runtime_put in the error case.
- The up is not freed in the error path. Fix the memory leak by using
devm_* so that the memory need not be freed in the driver.
- Also the iounmap is not called fix the same by calling using devm_ioremap.
- Make the name of the error tags more meaningful.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I made a mistake, please forgive me.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48254
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When booting with EFI, Apple botched this one up.
v2: Switch the quirk dmesg output to DRM_INFO.
v3: Actually git add the new things ...
Tested-by: Austin Lund <austin.lund@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42842
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add informational dmesg output where it does not yet exist.
In case a quirk matches too much, this information is crucial for
debugging such a bug report.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-and-tested-by: Bo Wang < bo.b.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36997
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ums is already disabled, but on ilk we can additionally disable gem
initialization when using user mode setting. Upstream never support
ilk without kernel modesetting and not even the RHEL ilk ums backport
needs gem - that driver is based on xf86-video-intel version 2.2,
which is pre-gem.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spurred by an irc discussion, let's start to clear up which parts of
our kms + ums/gem + ums/dri1 + vbios/dri1 kernel driver pieces
userspace in the wild actually uses.
The idea is that we introduce checks at entry-points (module load
time, ioctls, ...) first and then reap any obviously dead code in a
second step.
As a first step refuse to load without kms on chips where userspace
never supported ums. Now upstream hasn't supported ums on ilk, ever.
But RHEL had the great idea to backport the kms support to their ums
driver.
Cc: Dave Airlie <airlied@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv, ivb and snb all share the gen6+ gt irq handling. 3 copies of the
same stuff is a bit much, so extract it into a little helper.
Now ilk has a different gt irq handling than snb, but shares the same
irq handler (due to the similar display block). So also extract the
ilk gt irq handling to clearly separate these two things.
Nice side effect of this is that we can complete Ben Widawsky's gen6+
irq bit #define cleanup and call the render irq also with the GEN6
alias. Beforehand that code was shared with ilk, and neither option
really made much sense.
As a bonus this enables the error interrupt handling lifted from the
vlv code on snb and ivb, too.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Antagonized-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Top-level interrupt bits are usually found in the display block. It
therefore makes sense to use HAS_PCH_SPLIT in i915_irq.c
But the irq stuff in intel_ring.c only concerns itself with render
core/gt-level interrupt sources. It therefore makes more sense to
switch based on gpu gen.
Kills a vlv special case.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got copy-pasted from an older version. The newer kinds of
workarounds don't need this anymore.
Shame on me for not noticing when picking up the vlv irq patch.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can now open-code the get/put irq functions as they were just
abstracting single register definitions.
It would be nice to merge this in with the IRQ handling code... but that
is too much work for me at present. In addition I could probably
collapse this in to a lot of the Ironlake stuff, but I don't think it's
worth the potential regressions.
This patch itself should not effect functionality.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- gen6 put/get only need one argument
rflags and gflags are always the same (see above explanation)
- remove a couple redundantly defined IRQs
- reordered some lines to make things go in descending order
Every ring has its own interrupts, enables, masks, and status bits that
are fed into the main interrupt enable/mask/status registers. At one
point in time it seemed like a good idea to make our functions support
the notion that each interrupt may have a different bit position in the
corresponding register (blitter parser error may be bit n in IMR, but
bit m in blitter IMR). It turned out though that the HW designers did us
a solid on Gen6+ and this unfortunate situation has been avoided. This
allows our interrupt code to be cleaned up a bit.
I jammed this into one commit because there should be no functional
change with this commit, and staging it into multiple commits was
unnecessarily artificial IMO.
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet:
- fixed up merged conflict with vlv changes.
- added GEN6 to GT blitter bit, we only use it on gen6+.
- added a comment to both ring irq bits and GT irq bits that on gen6+
these alias.
- added comment that GT_BSD_USER_INTERRUPT is ilk-only.
- I've got confused a bit that we still use GT_USER_INTERRUPT on ivb
for the render ring - but this goes back to ilk where we have only
gt interrupt bits and so we be equally confusing if changed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDIA is detected via the DDI_BUF_CTL registers bit 0, but for DDIB, DDIC
and DDID we need to consult SFUSE_STRAP values.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Watermark line time registers for display low power watermark.
v2: improve bit names as suggested by Chris Wilson
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The WR PLL can drive the DDI ports at fixed frequencies for HDMI, DVI, DP
and FDI.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are used to control the display core clock.
v2: change the enable bit setting, spotted by Rodrigo Vivi.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Different registers are identified by their target id and offset. To
simplify their programming, they are called as <RegisterName><TargetId>.
For example, SSCCTL register accessed through SBI at target id 6 and
offset 0c is called SBI_SSCCTL6.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple clocks can drive different outputs.
v2: use the port enums to access individual ports
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This PLL control can drive DDI ports at desired frequencies for
DisplayPort and FDI connections.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are responsible for the Sideband Interface programming.
v2: rename SBI bits to better reflect their meaning
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those registers are used to train DDI buffer translations for each link
type.
v2: access each port registers through the DDI_BUF_TRANS macro
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one instance of those registers for each DDI port.
v2: access registers via the DDI_BUF_CTL() macro
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of those registers for each port.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is one set of those registers for each pipe.
v2: use port enum to access individual registers
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of such registers for each pipe (A/B/C/EDP).
v2: update to use DDI PORTS enum
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol. Ports B, C, D and E can be used for digital outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This defines the registers used by different power wells.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds product definitions for desktop, mobile and server boards.
v2: split into a separate patch, add .has_pch_split feature.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The macro is becoming too complex and with VLV upon us it can lead to
confusion. So transforming this into a feature check instead.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixed conflict with is_valleyview addition.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver frees the clock samples buffer before stopping the video
buffers queue. If a DQBUF call arrives in-between,
uvc_video_clock_update() will be called with a NULL clock samples
buffer, leading to a crash. This occurs very frequently when using the
webcam with the flash browser plugin.
Move clock initialization/cleanup to uvc_video_enable() in order to free
the clock samples buffer after the queue is stopped. Make sure the clock
is reset at resume time to avoid miscalculating timestamps.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
has_get_frontend() should return a boolean, not a pointer.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some systems the device does not respond or give obscure values after cold,
warm or firmware reboot.
This patch retries to get chip version and type 5 times. If it
fails it applies chip version 0x1 and type 0x9135.
This patch does not fix warm cycle problems from other operating
systems and indeed the reverse applies. Users should power off cold boot.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When I converted ivtv to the new decoder API I introduced a regression in the
support of the old channel select API.
Thanks to Martin Dauskardt for reporting this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit e399ce77e6 has broken the DVB ABI for xine:
The problem is that xine is expecting every event after a successful
FE_SET_FRONTEND ioctl to have a non-zero frequency parameter, regardless
of whether the tuning process has LOCKed yet. What used to happen is
that the events inherited the initial tuning parameters from the
FE_SET_FRONTEND call. However, the fepriv->parameters_out struct is now
not initialised until the status contains the FE_HAS_LOCK bit.
You might argue that this behaviour is intentional, except that if an
application other than xine uses the DVB adapter and manages to set the
parameters_out.frequency field to something other than zero, then xine
no longer has any problems until either the adapter is replugged or the
kernel modules reloaded. This can only mean that the
fepriv->parameters_out struct still contains the (stale) tuning
information from the previous application.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Cc: stable@kernel.org # for kernel version 3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dump tagmap on failure, instead of individual tags.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* If a ncq command time out and a non-ncq command is active, skip restart port
* Queue(pause) ncq commands during operations spanning more than one non-ncq commands - secure erase, download microcode
* When a non-ncq command is active, allow incoming non-ncq commands to wait instead of failing back
* Changed timeout for download microcode and smart commands
* If the device in write protect mode, fail all writes (do not send to device)
* Set maximum retries to 2
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shortened macros used to represent mtip_port->flags and dd->dd_flag
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Handle the interrupt completion of polled internal commands
* Do not check remove pending flag for standby command
* On rebuild failure,
- set corresponding bit dd_flag
- do not send standby command
* Free ida index in remove path
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Add support for detecting the following device status
- write protect
- over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Moved setting completion time into mtip_issue_ncq_command()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Merged the following flags into one variable 'dd_flag':
* drv_cleanup_done
* resumeflag
* Added the following flags into 'dd_flag'
* remove pending
* init done
* Removed 'ftlrebuildflag' (similar flag is already part of mti_port->flags)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kyrofb is completely broken on x86_64 because the registers are defined as
unsigned long. Change them to u32 to make the driver work.
Tested with Hercules 3D Prophet 4000XT.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk99uBgACgkQGkmNcg7/o7hglwCgqi6CE7i5gyneNYBn2ocRps4O
y1UAoMSIscO6YWcHPuxOiNBbJYUy/jMI
=SEO8
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Pull target fixes from Nicholas Bellinger:
"Pull two tcm_fc fabric related fixes for -rc2:
Note that both have been CC'ed to stable, and patch #1 is the
important one that addresses a memory corruption bug related to FC
exchange timeouts + command abort.
Thanks again to MDR for tracking down this issue!"
* '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Do not free tpg structure during wq allocation failure
tcm_fc: Add abort flag for gracefully handling exchange timeout
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
* one is a workaround that will be removed in v3.5 with proper fix in the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made them only
load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup in the
core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPfyVUAAoJEFjIrFwIi8fJUjUH/jbY5JavRqSlNELZW2A4Ta76
8p00LqLHw/C56iHZcWKke8mqtWNb+ZfcQt7ZYcxDIYa4QWBL28x0OLAO2tOBIt37
ZjYESWSdFJaJvmpADluWtFyGyZ9TYJllDTBm/jWj1ZtKSZvR1YkhuMXCS0f4AmGQ
xFzSWJZUDdiOAqpN+VQD8wP00gfR8knQLg16XE2fvFdQo4XwpCtqLfHV/5pMMGdy
Cs/ep6rq/7cdv/nshKOcBnw7RW8l3Xoi/28ht8k3DvAQ2VtFq1Tugv2G9pcCHwQG
DIBkB3SOU6/v6P5at5+egKS5xR1fJetCWlkMd8kkbcdz2NPI4UDMkvOW6Q8yQls=
=6Ve+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
The major fixes here are:
* Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
* Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
* Fix module reloading on omap_hsmmc.
* Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPfzfxAAoJEHNBYZ7TNxYMGBoP/02Drw+n4c7xykXdB7SSloq8
SGIAmh25EBFyZhcEmQ8Mm5qn4voHG8+Jm7ZXA3OipJ4xucu5fdoCIu/n8arGYa2u
GRB+GYOz92maCNBwLGZIMm7A64m2rkrRdwTw4pkjOZuJLh28GCshK2E+ZWoMKVNU
flaUna7NQc/p2eXulCNirry+4l1xxGW00lYaSOq78MTOKUMwWLCJZw+TUvfvxjX8
5BFc3b2+5fQKc1M0qh23oEcneRdOUUK6dWzvZHuQso1SkDeB1cetN9fzrhnys9or
tooIqd+GQRPJ6oGqe+VD8MT8HGMPb6oETZaFM7h7bt8nFcScu3iVjmJQLIbnsNBY
ho8AUkMbZtDtRBWDtk11zM9qrOWGufRdB0qW4R+4Zik1JohNp6SAeV7YSllIT4sT
lT5gdzAxAiZ992iwYKuwAn0SQOlevN2BjHMFGg8abZtlOWEWE2YIQ0nTJS2SCIyj
qbM9wmLZ2Ymo9KabRY+huRgrbViNHDzAQOLB/LEyvbPwD97arJE1R/OVNEasiv52
rh5pCsIa5oeUeX1fsfysfug+cO96Xm1oL/cGyLRj8WZB++nurHRm7ZAo36r8FLK1
4LpMokEEwpoPcbNqsfFvOy3aRV4sGNTDj+U8B4zyq9GigSoUwSAK7Nn2qbY9zIWj
W+oh3jfoyMbyVE5+00X7
=CCKD
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
- Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
- Fix module reloading on omap_hsmmc.
- Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
* tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (28 commits)
mmc: use really long write timeout to deal with crappy cards
mmc: sdhci-dove: Fix compile error by including module.h
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Revert "mmc: sdhci-pci: Add MSI support"
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
mmc: core: fix power class selection
mmc: omap_hsmmc: fix module re-insertion
mmc: omap_hsmmc: convert to module_platform_driver
mmc: omap_hsmmc: make it behave well as a module
mmc: omap_hsmmc: trivial cleanups
mmc: omap_hsmmc: context save after enabling runtime pm
mmc: omap_hsmmc: use runtime put sync in probe error patch
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
mmc: bus: print bus speed mode of UHS-I card
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
mmc: sh_mmcif: Simplify calculation of mmc->f_min
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc: sh_mmcif: double clock speed
mmc: block: Remove use of mmc_blk_set_blksize
mmc: atmel-mci: add support for odd clock dividers
...
Commit 360f748b204275229f8398cb2f9f53955db1503b
"serial: PL011: clear pending interrupts"
attempts to clear interrupts by writing to a
yet-unassigned memory address. This fixes the issue.
The breaking patch is marked for stable so should be
carried along with the other patch.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: stable <stable@vger.kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Reported-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1534c) updates the documentation for usb_unlink_urb and
related functions. It explains that the caller must prevent the URB
being unlinked from getting deallocated while the unlink is taking
place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com>
CC: Ming Lei <tom.leiming@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53c6bc24fd (usb: Don't make
USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.) Removed the
dependency of the USB_ARCH_HAS_* symbols on USB_SUPPORT. However the
resulting Kconfig somehow caused many of the USB configuration items
to appear under the top level devices menu.
To fix this we reunite the 'menuconfig USB_SUPPORT' with the 'if
USB_SUPPORT', and the config items magically go back to their desired
location.
Reported-by: Julian Wollrath <jwollrath@web.de>
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Rupesh Gujare <rgujare@ozmodevices.com>
Reported-by: Feng King <ronyjin@tencent.com>
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a NULL pointer dereference panic in cpuidle_play_dead() during
CPU off-lining when no cpuidle driver is registered. A cpuidle
driver may be registered at boot-time based on CPU type. This patch
allows an off-lined CPU to enter HLT-based idle in this condition.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Cc: Boris Ostrovsky <boris.ostrovsky@amd.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
commit b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Pull an APM fix from Jiri Kosina:
"One deadlock/race fix from Niel that got introduced when we were
moving away from freezer_*_count() to wait_event_freezable()."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
APM: fix deadlock in APM_IOC_SUSPEND ioctl
Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.
This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:
* With certain SD cards timeouts like the following have been seen
due to an improper calculation of the dto value:
mmcblk0: error -110 transferring data, sector 4126233, nr 8,
card status 0xc00
* By removing the dto calculation and setting the timeout value
to the maximum specified by the SD card specification part A2
section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
relevant ones are:
* http://talk.maemo.org/showthread.php?p=1000707#post1000707
* http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a compile error in drivers/mmc/host/sdhci-dove.c
by including the linux/module.h file.
Signed-off-by: Alf Høgemark <alf@i100.no>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit e6039832be.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.
According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.
Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
OMAP4 and OMAP3 HSMMC IP registers differ by 0x100 offset.
Adding the offset to platform_device resource structure
increments the start address for every insmod operation.
MMC command fails on re-insertion as module due to incorrect register
base. Fix this by updating the ioremap base address only.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This will delete some boilerplate code, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we put probe() on __init section, that will never work for multiple
module insertions/removals.
In order to make it work properly, move probe to __devinit section and
use platform_driver_register() instead of platform_driver_probe().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A bunch of non-functional cleanups to the omap_hsmmc driver.
It basically decreases indentation level, drop unneded dereferences
and drop unneded accesses to the platform_device structure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call context save api after enabling runtime pm to make sure that
register access in context save api happens with clk enabled.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
pm_runtime_put_sync instead of autosuspend pm runtime API
because iounmap(host->base) follows immediately.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Neil Brown reports that commit 35cd133c
PM: Run the driver callback directly if the subsystem one is not there
breaks suspend for his libertas wifi, because SDIO has a protocol
where the suspend method can return -ENOSYS and this means "There is
no point in suspending, just turn me off". Moreover, the suspend
methods provided by SDIO drivers are not supposed to be called by
the PM core or bus-level suspend routines (which aren't presend for
SDIO). Instead, when the SDIO core gets to suspend the device's
ancestor, it calls the device driver's suspend function, catches the
ENOSYS, and turns the device off.
The commit above breaks the SDIO core's assumption that the device
drivers' callbacks won't be executed if it doesn't provide any
bus-level callbacks. If fact, however, this assumption has never
been really satisfied, because device class or device type suspend
might very well use the driver's callback even without that commit.
The simplest way to address this problem is to make the SDIO core
tell the PM core to ignore driver callbacks, for example by providing
no-operation suspend/resume callbacks at the bus level for it,
which is implemented by this change.
Reported-and-tested-by: Neil Brown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
[stable: please apply to 3.3-stable only]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When UHS-I card is detected also print the bus speed mode in which
UHS-I card will be running.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MSI on my O2Micro OZ600 SD card reader is broken. This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no need to tune mmc->f_min to a value near 400kHz as the MMC core
begins testing frequencies at 400kHz regardless of the value of mmc->f_min.
As suggested by Guennadi Liakhovetski.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc->f_max should be half of the bus clock.
And now that mmc->f_max is not equal to the bus clock the
latter should be used directly to calculate mmc->f_min.
Cc: Magnus Damm <magnus.damm@gmail.com>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Correct an off-by one error when calculating the clock divisor in cases
where the host clock is a power of two of the target clock. Previously the
divisor was one greater than the correct value in these cases leading to
the clock being set at half the desired speed.
Thanks to Guennadi Liakhovetski for working with me on the logic for this
change.
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since most of the work is already done by the core we just need to add
runtime suspend methods and tell the PM core that runtime PM is enabled
for this device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This matches current best practice as one can have runtime PM enabled
without system sleep and CONFIG_PM is defined for both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
The call to platform_get_resource was moved just to make it closer to the
place where its result it used.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the sdhci-s3c driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_width member in platform data can be used to derive the mmc bus transfer
width that can be supported by the controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI controllers on Exynos4 do not include the sdclk divider as per the
sdhci controller specification. This case can be represented using the
sdhci quirk SDHCI_QUIRK_NONSTANDARD_CLOCK instead of using an additional
enum type definition 'clk_types'.
Hence, usage of clk_type member in platform data is removed and the sdhci
quirk is used. In addition to that, since this qurik is SoC specific,
driver data is introduced to represent controllers on SoC's that require
this quirk.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
This is the fallout from adding memcpy alignment workaround for certain
IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align
ops.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS. It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.
This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to 88pm860x spec, rtc alarm irq enable control is bit3 for
RTC_ALARM_EN, so fix it.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change send_sig_all() to use do_send_sig_info(SEND_SIG_FORCED) instead
of force_sig(SIGKILL). With the recent changes we do not need force_ to
kill the CLONE_NEWPID tasks.
And this is more correct. force_sig() can race with the exiting thread,
while do_send_sig_info(group => true) kill the whole process.
Some more notes from Oleg Nesterov:
> Just one note. This change makes no difference for sysrq_handle_kill().
> But it obviously changes the behaviour sysrq_handle_term(). I think
> this is fine, if you want to really kill the task which blocks/ignores
> SIGTERM you can use sysrq_handle_kill().
>
> Even ignoring the reasons why force_sig() is simply wrong here,
> force_sig(SIGTERM) looks strange. The task won't be killed if it has
> a handler, but SIG_IGN can't help. However if it has the handler
> but blocks SIGTERM temporary (this is very common) it will be killed.
Also,
> force_sig() can't kill the process if the main thread has already
> exited. IOW, it is trivial to create the process which can't be
> killed by sysrq.
So, this patch fixes the issue.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silicon errata where when RAID and legacy descriptors are mixed, the legacy
(memcpy and friends) operation must have alignment of 64 bytes to avoid
hanging. This effects Intel Xeon C55xx, C35xx, E5-2600.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The alloc order can be up to 16 and 1 << 16 will over flow the 16bit
integer. Change the appropriate variables to 16bit to avoid overflow.
Reported-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-3.4/fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain
"halt()" function. Use safe_halt() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
NV12, NV12M and NV12MT are added to format list of plane to use these
formats for hdmi vp layer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.
This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.
This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.
Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3.4: Fix an an Smatch warning that appeared in the 3.4 merge window
3.0: Fix kgdb test suite with SMP for all archs without HW single stepping
2.6.36: Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
2.6.26: Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
Fix kgdb test suite with SMP for all archs with HW single stepping
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SW2N
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
Pull DMA mapping branch from Marek Szyprowski:
"Short summary for the whole series:
A few limitations have been identified in the current dma-mapping
design and its implementations for various architectures. There exist
more than one function for allocating and freeing the buffers:
currently these 3 are used dma_{alloc, free}_coherent,
dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent.
For most of the systems these calls are almost equivalent and can be
interchanged. For others, especially the truly non-coherent ones
(like ARM), the difference can be easily noticed in overall driver
performance. Sadly not all architectures provide implementations for
all of them, so the drivers might need to be adapted and cannot be
easily shared between different architectures. The provided patches
unify all these functions and hide the differences under the already
existing dma attributes concept. The thread with more references is
available here:
http://www.spinics.net/lists/linux-sh/msg09777.html
These patches are also a prerequisite for unifying DMA-mapping
implementation on ARM architecture with the common one provided by
dma_map_ops structure and extending it with IOMMU support. More
information is available in the following thread:
http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819
More works on dma-mapping framework are planned, especially in the
area of buffer sharing and managing the shared mappings (together with
the recently introduced dma_buf interface: commit d15bd7ee44
"dma-buf: Introduce dma buffer sharing mechanism").
The patches in the current set introduce a new alloc/free methods
(with support for memory attributes) in dma_map_ops structure, which
will later replace dma_alloc_coherent and dma_alloc_writecombine
functions."
People finally started piping up with support for merging this, so I'm
merging it as the last of the pending stuff from the merge window.
Looks like pohmelfs is going to wait for 3.5 and more external support
for merging.
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
common: DMA-mapping: add NON-CONSISTENT attribute
common: DMA-mapping: add WRITE_COMBINE attribute
common: dma-mapping: introduce mmap method
common: dma-mapping: remove old alloc_coherent and free_coherent methods
Hexagon: adapt for dma_map_ops changes
Unicore32: adapt for dma_map_ops changes
Microblaze: adapt for dma_map_ops changes
SH: adapt for dma_map_ops changes
Alpha: adapt for dma_map_ops changes
SPARC: adapt for dma_map_ops changes
PowerPC: adapt for dma_map_ops changes
MIPS: adapt for dma_map_ops changes
X86 & IA64: adapt for dma_map_ops changes
common: dma-mapping: introduce generic alloc() and free() methods
In commit (bfab27a stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
