Since the BCM2835 datasheet doesn't exactly specify the set-up time for
the GPIO Pull-up/down Clock Registers there was an assumption of 150 cycles
at a clock rate of 1 MHz. During a discussion [1] in the Raspberry Pi forum
it turns out that clock rate refers to the VPU which has a rate of 250 MHz.
So we can reduce the delay to a sensible value and update the comment above.
I tested this optimization with a Raspberry Pi B and a multimeter.
[1] - https://www.raspberrypi.org/forums/viewtopic.php?f=72&t=163352
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Printing the prefix does not provide any additional information. In
addition this makes the output look more consistent with pinctrl-intel.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The hardware supports a 16 and 8 bit wide NAND bus, let users pick
either.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even though the our binding had the assumption that the allwinner,pull and
allwinner,drive properties were optional, the code never took that into
account.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin config get() and set() handlers for pin groups were previously not
implemented by this driver. The pin_config_group_set() is particularly useful
for applying a common config setting to all pins in a specified group with a
single call, without the caller needing to reference each individual pin by
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During pinmux registration, pinmux table is parsed from DT
for making the pinmux table configuration of pins.
Parse the only those node whose status is not disabled.
This will help on reusing the pin configuration table across
platform and disabling the node by status property if that node
is not needed on given platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers using pinconf_generic_params tables cannot be built with
CONFIG_OF disabled:
drivers/pinctrl/pinctrl-max77620.c:53:44: error: array type has incomplete element type ‘struct pinconf_generic_params’
drivers/pinctrl/pinctrl-max77620.c:55:3: error: field name not in record or union initializer
drivers/pinctrl/pinctrl-max77620.c:55:3: note: (near initialization for ‘max77620_cfg_params’)
drivers/pinctrl/pinctrl-max77620.c:56:3: error: field name not in record or union initializer
This adds a dependency for max77620 to disallow that configuration.
Alternatively, we could rework the pinctrl infrastructure to make the
configuration valid for compile-testing.
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: 453943dc8f45 ("mfd: Enable compile testing for max77620 and max77686")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is left over from initial experiments with more properties.
It's only used in one place, so let's just get rid of it to make
the code more readable.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>From tony Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 25 Oct 2016 08:33:34 -0700
Subject: [PATCHv2] pinctrl: single: Drop custom names
We no longer need to allocate custom names as those are dynamically
generated in pinctrl_register_one_pin() if no name is passed to
pinctrl_register_pins().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pin configuration and multiplexing should be preferred now,
even though we still support the old one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our bindings are mostly irrelevant now that we have generic pinctrl
bindings that cover exactly the same uses cases.
Add support for the new ones, and obviously keep our old binding support in
order to keep the ABI stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Oxford Semiconductor OX820 which is similar as OX810 but
has 50 pins and two registers banks to setup alternate functions.
Add specific pins, groups and functions structures.
Add DT match data to select corresponding support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add refactoring to move ox810se specific functions into specific ops structures
an add support for the dt match data to get soc specific structures.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So far, putting NO_PULL in allwinner,pull was ignored, behaving like if
that property was not there at all.
Obviously, this is not the right thing to do, and in that case, we really
need to just disable the bias.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we have some bindings header for our hardcoded flags, let's use them
when we can.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support more easily the generic pinctrl properties, rework the
pinctrl maps configuration and split it into several sub-functions.
One of the side-effects from that rework is that we only parse the pin
configuration once, since it's going to be common to every pin, instead of
having to parsing once for each pin.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fallout from the merge window, refactoring UBI code introduced some issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy loop
for ever and a bug in the UBIFS xattr code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gjo0
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs
Pull UBI[FS] fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- Fallout from the merge window, refactoring UBI code introduced some
issues.
- Fixes for an UBIFS readdir bug which can cause getdents() to busy
loop for ever and a bug in the UBIFS xattr code"
* tag 'upstream-4.9-rc2' of git://git.infradead.org/linux-ubifs:
ubifs: Abort readdir upon error
UBI: Fix crash in try_recover_peb()
ubi: fix swapped arguments to call to ubi_alloc_aeb
ubifs: Fix xattr_names length in exit paths
ubifs: Rename ubifs_rename2
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYDK6KAAoJEPL5WVaVDYGjhZ0H/2aLu4BQOmIPJZBBS+I2FurE
7FFdnQ8r1gBPWktvfUTn6MzTE4VKe0b1js5EiRCiCJhJq9UadBu53dUWTgfZ5Egi
Sc6p0NGqDRgixLXbFRt8wP7iPtVg0tlysE0EJ6ae4VA1wUpf5aoHaPqgO9V0hirW
9pUJq8kzBGs628CROcYtQ5IL5AfouM1q/fzazw4Voz48LTgvhnDGCkqQmNsKkRo+
bN5tkjSTQUdW3OrRVsNwNND/iDYpTa6PcX1XXQiFFhQ4SbZoNS/dzowz09QreGxA
Uz/rt2hMnv552Zd52d5q6N/jPWg+O+x0b4PcYtn7NDjPn/1KZUyX0pQK/EoevXQ=
=2Kri
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A few bug fixes and add some missing KERN_CONT annotations"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: add missing KERN_CONT to a few more debugging uses
fscrypto: lock inode while setting encryption policy
ext4: correct endianness conversion in __xattr_check_inode()
fscrypto: make XTS tweak initialization endian-independent
ext4: do not advertise encryption support when disabled
jbd2: fix incorrect unlock on j_list_lock
ext4: super.c: Update logging style using KERN_CONT
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target-pending fixes for v4.9-rc2.
This includes:
- Fix v4.1.y+ reference leak regression with concurrent TMR
ABORT_TASK + session shutdown. (Vaibhav Tandon)
- Enable tcm_fc w/ SCF_USE_CPUID to avoid host exchange timeouts
(Hannes)
- target/user error sense handling fixes. (Andy + MNC + HCH)
- Fix iscsi-target NOP_OUT error path iscsi_cmd descriptor leak
(Varun)
- Two EXTENDED_COPY SCSI status fixes for ESX VAAI (Dinesh Israni +
Nixon Vincent)
- Revert a v4.8 residual overflow change, that breaks sg_inq with
small allocation lengths.
There are a number of folks stress testing the v4.1.y regression fix
in their environments, and more folks doing iser-target I/O stress
testing atop recent v4.x.y code.
There is also one v4.2.y+ RCU conversion regression related to
explicit NodeACL configfs changes, that is still being tracked down"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/tcm_fc: use CPU affinity for responses
target/tcm_fc: Update debugging statements to match libfc usage
target/tcm_fc: return detailed error in ft_sess_create()
target/tcm_fc: print command pointer in debug message
target: fix potential race window in target_sess_cmd_list_waiting()
Revert "target: Fix residual overflow handling in target_complete_cmd_with_length"
target: Don't override EXTENDED_COPY xcopy_pt_cmd SCSI status code
target: Make EXTENDED_COPY 0xe4 failure return COPY TARGET DEVICE NOT REACHABLE
target: Re-add missing SCF_ACK_KREF assignment in v4.1.y
iscsi-target: fix iscsi cmd leak
iscsi-target: fix spelling mistake "Unsolicitied" -> "Unsolicited"
target/user: Fix comments to not refer to data ring
target/user: Return an error if cmd data size is too large
target/user: Use sense_reason_t in tcmu_queue_cmd_ring
I was on vacation during the merge window (a long vacation)
but this is a bug fix that should go in and a new driver that shouldn't
hurt anything.
This has been in linux-next for a month or so.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlgKVpoACgkQIXnXXONXERdGBACeONBS0wOf4Rv+bxSOdeJcTwLJ
rmoAoJ2R0BpWE1imvcC+AqXOoqg2c48k
=P4Dz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
Pull x86 fixes from Ingo Molnar:
"Three fixes, a hw-enablement and a cross-arch fix/enablement change:
- SGI/UV fix for older platforms
- x32 signal handling fix
- older x86 platform bootup APIC fix
- AVX512-4VNNIW (Neural Network Instructions) and AVX512-4FMAPS
(Multiply Accumulation Single precision instructions) enablement.
- move thread_info back into x86 specific code, to make life easier
for other architectures trying to make use of
CONFIG_THREAD_INFO_IN_TASK_STRUCT=y"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/smp: Don't try to poke disabled/non-existent APIC
sched/core, x86: Make struct thread_info arch specific again
x86/signal: Remove bogus user_64bit_mode() check from sigaction_compat_abi()
x86/platform/UV: Fix support for EFI_OLD_MEMMAP after BIOS callback updates
x86/cpufeature: Add AVX512_4VNNIW and AVX512_4FMAPS features
x86/vmware: Skip timer_irq_works() check on VMware
Pull vmap stack fixes from Ingo Molnar:
"This is fallout from CONFIG_HAVE_ARCH_VMAP_STACK=y on x86: stack
accesses that used to be just somewhat questionable are now totally
buggy.
These changes try to do it without breaking the ABI: the fields are
left there, they are just reporting zero, or reporting narrower
information (the maps file change)"
* 'mm-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm: Change vm_is_stack_for_task() to vm_is_stack_for_current()
fs/proc: Stop trying to report thread stacks
fs/proc: Stop reporting eip and esp in /proc/PID/stat
mm/numa: Remove duplicated include from mprotect.c
Pull irq fixes from Ingo Molnar:
"Mostly irqchip driver fixes, plus a symbol export"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/irq: Export irq_set_parent()
irqchip/gic: Add missing \n to CPU IF adjustment message
irqchip/jcore: Don't show Kconfig menu item for driver
irqchip/eznps: Drop pointless static qualifier in nps400_of_init()
irqchip/gic-v3-its: Fix entry size mask for GITS_BASER
irqchip/gic-v3-its: Fix 64bit GIC{R,ITS}_TYPER accesses
Pull EFI fixes from Ingo Molnar:
"Add Ard Biesheuvel as EFI co-maintainer, plus fix an ARM build bug
with older toolchains"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm: Fix absolute relocation detection for older toolchains
MAINTAINERS: Add myself as EFI maintainer
Apparently trying to poke a disabled or non-existent APIC
leads to a box that doesn't even boot. Let's not do that.
No real clue if this is the right fix, but at least my
P3 machine boots again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: dyoung@redhat.com
Cc: kexec@lists.infradead.org
Cc: stable@vger.kernel.org
Fixes: 2a51fe083e ("arch/x86: Handle non enumerated CPU after physical hotplug")
Link: http://lkml.kernel.org/r/1477102684-5092-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=39+z
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)"
* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore the pkey system calls for now
powerpc: Fix numa topology console print
powerpc/mm: Drop dump_numa_memory_topology()
cxl: Prevent adapter reset if an active context exists
powerpc/boot: Fix boot on systems with uncompressed kernel image
powerpc/mm: Prevent unlikely crash in copro_calculate_slb()
Specifics:
- Update the ACPI WDAT-based watchdog driver to ping the hardware
during system resume to prevent a reset from occurring after the
resume is complete (Mika Westerberg).
- Fix the return value of the pcc_mbox_request_channel() stub for
CONFIG_PCC unset (Hoan Tran).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJYCn8AAAoJEILEb/54YlRxo7YQAIeJ0Sx6wdHrgpFVKuajhTtv
eJ2j21ttMZODk6iWX0Xfr1pT5GYteKoBXQvc2qHdtGnN9H9RbBJ/Ai0qL4XrnSGP
TuaTBuePapogt02eK8mVb3mrFQrjOJvsWhE4hQSfHvCylAAM0w682APIQshjY8xY
RtYWCoDHupFm5CGp4bN0X+AzPorB+BX+cg8bGqFDnk/b1pCVwCuW3VTq0Ni6SIJZ
k+eDCT8K+r04pcBo+dMHx2RKRR9ZaGavm++u+5tnWoxRy7rhfj2txZyRnmd2znlq
brKm4Tv1cnnCo8FLCuRNuqJ9OcYMpUPVtWN2ESzE/k6WPjzs2jEWEoSdmW/JB6dM
4a8LsjRQLjMw3IS6sonAS6wo1DO8Tb+RcZH1MeDWMm3K6rqnYIcPknldoWDaoHYz
9uNDMWeHsaYKtvAXZXHkaOd3cl1ESY1E9jGO0xR/CBikaRKBAAHzCIHPIUvJzIRm
3KLWpMIiT++AcSrUQxVLgEHjkERh+Ph9LpnEdVOqcB+r7O/p3zr7aFO4iZCgZ9kH
LZXfVI53YbX7vnCzMHgUToutZPkHsqzxathAsJnVS83GgxTsciX+O5/k7lHgCb7G
gl9ReeweWpVKqrT/o4wStbTB56UYjOWzZcAsA0pWeKUiqUycTSVfiad1tr7lM+cs
lJb5i8Pl6bJu6+nWm4lN
=kG+5
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix an issue related to system resume in the new WDAT-based
watchdog driver and a return value of a stub function in the ACPI CPPC
framework.
Specifics:
- Update the ACPI WDAT-based watchdog driver to ping the hardware
during system resume to prevent a reset from occurring after the
resume is complete (Mika Westerberg).
- Fix the return value of the pcc_mbox_request_channel() stub for
CONFIG_PCC unset (Hoan Tran)"
* tag 'acpi-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
watchdog: wdat_wdt: Ping the watchdog on resume
mailbox: PCC: Fix return value of pcc_mbox_request_channel()
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYCkl/AAoJECPQ0LrRPXpDpJwQAMOOccZo7T2Ekt41R2kup1lg
l1OWvJ5N22uTxnS6+fNp+JhHdwzVk2TJeYFkoxYfbSPUtEVJYEKm4ZPdlIG58bhE
N/Yh5QIzOcHUWRr000PaTgap9G0HUNSm0RJfLlH/zbscpiDWuJQLZ/OK2uWtRn1+
hIQd8Poz85jfCZIb/AnSdA4YKJfww7JwviA3UuQjatqpkoIlfz/3CvJbx4DXPcrT
EBC3vEeCYiALYQGImwY/P6VzYriS/fU+QWHkE1er5PPq+PRak1cmPAS15FBvQwVy
wCI3zo3aSD+Y7tbKa1AvcOK6xIZq4UJaVX+sWd2pb0oz5T17dYjyXbzm+VRblT+b
CNTrRZvFOxJH4ImHM4FT9ioRUme65XiUOQ9g3LrMTJGI4nfKmRaF4tOzlTsfHJxT
HiBXWV6s98maK3ltfqKdEY4qhsNMdi3bZNnu8fTVhZEUugMu4ywLXyNqfISdJ+MG
gvbDojXkvMtFGPZHg1vuHuEqdBHH+5Wbh5TCbWykMkhGbYEkLT23YZgLRo5TbN1E
OMLVhx+dblmaMn+Npyo2BtST9E2Akzym9R+hx4rqNrRH5NQvGrAlPAIFA/1ommYI
qdC5vJNYGH+B+uPRSKUUx9kwl+NUTPDLSzYSrIAHzTyYnenJ+QvBE2Zd3z6NplCn
NtctzCoOEjN2Q6WsSGVI
=DL0w
-----END PGP SIGNATURE-----
Merge tag 'gic-fixes-for-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull GIC updates from Marc Zyngier:
- Fix for 32bit accesses that should be 64bit on 64bit machines
- Fix for a field decoding macro
- Beautify a warning message
Five small fixes. Some of these, like the nested spinlock overwriting saved
flags and the Kasan use after free look serious, but they seem not to have
been picked up in testing or seen in the field. The biggest user visible
issue is probably the wrong device handler for Clariion, which means that alua
doesn't bind to the array like it should.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYCkR8AAoJEAVr7HOZEZN44WYQALPU6JSf/NAEv6wNAoD4eUBu
uwIfLHn+gUDKZFX5n+XZs4UsBtSQqRtIzooem7Xp5WmC8H/aZgFJTn+F7xkZ9YKY
hCm0E5Frz2K1euXeASdlbRmGm+sXec4YVu0mzdy8LON15uJNkqJAPq/RxVvhqQzo
8KwZ8dp1Gbed8DB8Ka/WkIciEY3xR/9Man+bFTOV/XJ7tiZYxsTtclFVWZ2KrDwn
1J9ZLGr4x1+YsusQc0zA9ykGO3XVUxdG8HHRLtAQo6IKK+SDOO0+6p3B94Ay0YSb
XPdeA8XVqC5kmOX6HBAGYa0uzcoFFVYU3ADw4cFmbvfOvaaeeM4vuhG4vm++ieVI
NjX/+9epyc25lJ6S2frCaR1rRHjODLbuo2xgEcs+2wuQu4cYrQxIZUUVeeLB11HO
WFzaSS8CFmDRokxR1sqFNq1o+JQ3jcnbQwc2awrYDfzV4RPRcHUx0HNIEo0JVsjJ
oMKCSiEJG6RslRNC1hTJGtdxPk9A4MtQBhfzhdqHBJvKQZjO7g3ivOcbHn0iMk1g
9U+fWvhaXRDXUEiiGFip3rLNnmN0lQCWWtq4jvYBY6VBT39V2FauGJ8707HeCujN
GKFRM60qzIc7Xus24HfgUp6/BMMwTrL7T3TLUxukRKS1G+N/qKHpev3i96NB0gAY
Rn39EUX/YIEuTONNnv50
=nB7G
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five small fixes.
Some of these, like the nested spinlock overwriting saved flags and
the Kasan use after free look serious, but they seem not to have been
picked up in testing or seen in the field.
The biggest user visible issue is probably the wrong device handler
for Clariion, which means that alua doesn't bind to the array like it
should"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: Fix async error WARN_ON
scsi: zfcp: spin_lock_irqsave() is not nestable
scsi: Remove one useless stack variable
scsi: Fix use-after-free
scsi: Replace wrong device handler name for CLARiiON arrays
Pull block fixes from Jens Axboe:
"A set of fixes that missed the merge window, mostly due to me being
away around that time.
Nothing major here, a mix of nvme cleanups and fixes, and one fix for
the badblocks handling"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: use symbolic constants for CNS values
nvme: use symbolic constants for CNS values
nvme.h: add an enum for cns values
nvme.h: don't use uuid_be
nvme.h: resync with nvme-cli
nvme: Add tertiary number to NVME_VS
nvme : Add sysfs entry for NVMe CMBs when appropriate
nvme: don't schedule multiple resets
nvme: Delete created IO queues on reset
nvme: Stop probing a removed device
badblocks: fix overlapping check for clearing
- Handle faults generated by the page table walker as being writes
- Map the BSS at EL2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DVps
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM updates for 4.9-rc2
- Handle faults generated by the page table walker as being writes
- Map the BSS at EL2
When used with a compiler that doesn't implement "asm goto"
(such as the AArch64 port of GCC 4.8), jump labels generate a
memory access to find out about the value of the key (instead
of just patching the code). The key itself is likely to be
stored in the BSS.
This is perfectly fine, except that we don't map the BSS at HYP,
leading to an exploding kernel at the first access. The obvious
fix is simply to map the BSS there (which should have been done
a long while ago, but hey...).
Reported-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The WnR bit in the HSR/ESR_EL2 indicates whether a data abort was
generated by a read or a write instruction. For stage 2 data aborts
generated by a stage 1 translation table walk (i.e. the actual page
table access faults at EL2), the WnR bit therefore reports whether the
instruction generating the walk was a load or a store, *not* whether the
page table walker was reading or writing the entry.
For page tables marked as read-only at stage 2 (e.g. due to KSM merging
them with the tables from another guest), this could result in livelock,
where a page table walk generated by a load instruction attempts to
set the access flag in the stage 1 descriptor, but fails to trigger
CoW in the host since only a read fault is reported.
This patch modifies the arm64 kvm_vcpu_dabt_iswrite function to
take into account stage 2 faults in stage 1 walks. Since DBM cannot be
disabled at EL2 for CPUs that implement it, we assume that these faults
are always causes by writes, avoiding the livelock situation at the
expense of occasional, spurious CoWs.
We could, in theory, do a bit better by checking the guest TCR
configuration and inspecting the page table to see why the PTE faulted.
However, I doubt this is measurable in practice, and the threat of
livelock is real.
Cc: <stable@vger.kernel.org>
Cc: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
-----BEGIN PGP SIGNATURE-----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=Jsu/
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.9-rc2-part2' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Mainly some vmwgfx fixes, but also some fixes for armada, etnaviv and
fsl-dcu"
* tag 'drm-fixes-for-v4.9-rc2-part2' of git://people.freedesktop.org/~airlied/linux:
drm/fsl-dcu: enable pixel clock when enabling CRTC
drm/fsl-dcu: do not transfer registers in mode_set_nofb
drm/fsl-dcu: do not transfer registers on plane init
drm/fsl-dcu: enable TCON bypass mode by default
drm/vmwgfx: Adjust checks for null pointers in 13 functions
drm/vmwgfx: Use memdup_user() rather than duplicating its implementation
drm/vmwgfx: Use kmalloc_array() in vmw_surface_define_ioctl()
drm/vmwgfx: Avoid validating views on view destruction
drm/vmwgfx: Limit the user-space command buffer size
drm/vmwgfx: Remove a leftover debug printout
drm/vmwgfx: Allow resource relocations on byte boundaries
drm/vmwgfx: Enable SVGA_3D_CMD_DX_TRANSFER_FROM_BUFFER command
drm/vmwgfx: Remove call to reservation_object_test_signaled_rcu before wait
drm/vmwgfx: Replace numeric parameter like 0444 with macro
drm/etnaviv: block 64K of address space behind each cmdstream
drm/etnaviv: ensure write caches are flushed at end of user cmdstream
drm/armada: fix clock counts
Although I am leaving Synopsys, I would like to keep working with the linux
kernel community and help in what you might find useful. For that I am
sending this patch to change my contact e-mail.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The TPS65217 driver grew interrupt support which uses
irq_set_parent(). While it's not yet clear why this is used in the first
place, building the driver as a module fails with:
ERROR: ".irq_set_parent" [drivers/mfd/tps65217.ko] undefined!
The correctness of the driver change is still investigated, but for now
it's less trouble to export irq_set_parent() than dealing with the build
wreckage.
[ tglx: Rewrote changelog and made the export GPL ]
Fixes: 6556bdacf6 ("mfd: tps65217: Add support for IRQs")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Link: http://lkml.kernel.org/r/1475775403-27207-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The libfc stack assigns exchange IDs based on the CPU the request
was received on, so we need to send the responses via the same CPU.
Otherwise the send logic gets confuses and responses will be delayed,
causing exchange timeouts on the initiator side.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Update the debug statements to match those from libfc.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Not every failure is due to out-of-memory; the ACLs might not be
set, too. So return a detailed error code in ft_sess_create()
instead of just a NULL pointer.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>