Four architectures (arm, mips, sparc, x86) use __vmalloc_area() for
module_init(). Much of the code is duplicated and can be generalized in a
globally accessible function, __vmalloc_node_range().
__vmalloc_node() now calls into __vmalloc_node_range() with a range of
[VMALLOC_START, VMALLOC_END) for functionally equivalent behavior.
Each architecture may then use __vmalloc_node_range() directly to remove
the duplication of code.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Occasionally the system gets into a state where the CMOS clock has gotten
slightly ahead of current time and the periodic update of RTC fails. The
message is a nuisance and repeats spamming the log.
See: http://www.ntp.org/ntpfaq/NTP-s-trbl-spec.htm#Q-LINUX-SET-RTC-MMSS
Rather than just removing the message, make it show only once and reduce
severity since it indicates a normal and non urgent condition.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
The device tree code is now in two pieces: some which can be used generically
on any platform which selects CONFIG_OF_FLATTREE, and some early which is used
at boot time on only a few architectures. This patch segregates the early
code so that only those architectures which care about it need compile it.
This also means that some of the requirements in the early code (such as
a cmd_line variable) that most architectures (e.g. X86) don't provide
can be ignored.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
[grant.likely@secretlab.ca: remove extra blank line addition]
[grant.likely@secretlab.ca: fixed incorrect #ifdef CONFIG_EARLY_FLATTREE check]
[grant.likely@secretlab.ca: Made OF_EARLY_FLATTREE select instead of depend
on OF_FLATTREE]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Seen with malta_defconfig on Linus' tree:
CC arch/mips/mm/sc-mips.o
arch/mips/mm/sc-mips.c: In function 'mips_sc_is_activated':
arch/mips/mm/sc-mips.c:77: error: 'config2' undeclared (first use in this function)
arch/mips/mm/sc-mips.c:77: error: (Each undeclared identifier is reported only once
arch/mips/mm/sc-mips.c:77: error: for each function it appears in.)
arch/mips/mm/sc-mips.c:81: error: 'tmp' undeclared (first use in this function)
make[2]: *** [arch/mips/mm/sc-mips.o] Error 1
make[1]: *** [arch/mips/mm] Error 2
make: *** [arch/mips] Error 2
[Ralf: Cosmetic changes to minimize the number of arguments passed to
mips_sc_is_activated]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For huge page support with base page size of 16K or 32K, we have to
increase the MAX_ORDER so that huge pages can be allocated.
[Ralf: I don't think a user should have to configure obscure constants like
this but for the time being this will have to suffice.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I am about to commit:
http://sourceware.org/ml/binutils/2010-10/msg00033.html
that fixes a problem with the LD/SD macro currently implemented by GAS for
the o32 ABI in an inconsistent way. This is best illustrated with a
simple program, which I'm copying here from the message above for easier
reference:
$ cat ld.s
ld $5,32767($4)
ld $5,32768($4)
This gets assebled into the following output:
$ mips-linux-as -32 -mips3 -o ld.o ld.s
$ mips-linux-objdump -d ld.o
ld.o: file format elf32-tradbigmips
Disassembly of section .text:
00000000 <.text>:
0: dc857fff ld a1,32767(a0)
4: 3c010001 lui at,0x1
8: 00810821 addu at,a0,at
c: 8c258000 lw a1,-32768(at)
10: 8c268004 lw a2,-32764(at)
...
Oops!
The GAS fix makes the macro behave in a consistent way and pairs of LW/SW
instructions to be output as appropriate regardless of the size of the
offset associated with the address used. The machine instruction is still
available, but to reach it macros have to be disabled first. This has a
side effect of requiring the use of a machine-addressable memory operand.
As some platforms require 64-bit operations for accesses to some I/O
registers LD/SD instructions are used in a couple of places in Linux
regardless of the ABI selected. Here's a fix for some pieces of code
affected I've been able to track down. The fix should be backwards
compatible with all supported binutils releases in existence and can be
used as a reference for any other places or off-tree code. The use of the
"R" constraint guarantees a machine-addressable operand.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1680/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In commit 7d172bfe ("Alchemy: Add UART PM methods") I introduced
platform PM methods which call a function of the 8250 driver;
this patch works around link failures when the kernel is built
without 8250 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1737/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Consider the following test case:
write_c0_compare(read_c0_count());
Even if the counter doesn't increment during execution, this might not
generate an interrupt until the counter wraps around. The CPU may
perform the comparison each time CP0 COUNT increments, not when CP0
COMPARE is written.
If mips_next_event() is called with a very small delta, and CP0 COUNT
increments during the calculation of "cnt += delta", it is possible
that CP0 COMPARE will be written with the current value of CP0 COUNT.
If this is detected, the function should return -ETIME, to indicate
that the interrupt might not have actually gotten scheduled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM4710 uses the BMIPS32 core (like BCM6345), not the MIPS 4Kc core as
was previously believed.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Alexandros C. Couloumbis <alex@ozo.com>
Patchwork: https://patchwork.linux-mips.org/patch/1837/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
partial_fixup is used in noreorder block.
Separating two consecutive loads can save one cycle on processors with
GPR intrelock and can fix load-use on processors that need a load delay slot.
Also do so for fwd_fixup.
[Ralf: Only R2000/R3000 class processors are lacking the the load-user
interlock and even some of those got it retrofitted. With R2000/R3000
being fairly uncommon these days the impact of this bug should be minor.]
Signed-off-by: Tony Wu <tung7970@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1768/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were unconditionally sending SIGBUS with an empty siginfo on FP
emulator faults. This differs from what happens when real floating
point hardware would get a fault.
For most faults we need to send SIGSEGV with the faulting address
filled in in the struct siginfo.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TNETD7200 run their CPU clock faster than the default CPU clock we assume.
In order to have the correct loops per jiffies settings, initialize clocks right
before setting mips_hpt_frequency. As a side effect, we can no longer use
msleep in clocks.c which requires other parts of the kernel to be initialized,
so replace these with mdelay.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent changes to CONFIG_GENERIC_HARDIRQS have caused us to start getting:
warning: (SMP && SYS_SUPPORTS_SMP) selects IRQ_PER_CPU which has unmet direct dependencies (HAVE_GENERIC_HARDIRQS)
Rearranging our Kconfig quiets the message.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/1757/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:49: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:50: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:51: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
arch/mips/loongson/common/env.c:52: error: ignoring return value of 'strict_strtol', declared with attribute warn_unused_result
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1762/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The return value of the vmalloc() call in arch/mips/kernel/vpe.c::vpe_open()
is not checked, so we potentially store a null pointer in v->pbuffer. Add
a check for a null return and then return -ENOMEM in that case.
[Ralf: The check added by Jesper's original patch is where it logically
should be. Adding it eleminated the need for the checks in a few other
places, so I removed them. There still is a zillion of other things that
need to be fixed in this file / API.]
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If PER_LINUX32 has been set on a 32-bit kernel, only twiddle with the
low-order personality bits, let the upper bits pass through.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1751/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The high bits of current->personality carry settings that we don't want to
clobber on each exec. Only clobber them if the lower bits that indicate
either PER_LINUX or PER_LINUX32 are invalid.
The clobbering prevents us from using useful bits like ADDR_NO_RANDOMIZE.
Reported-by: Camm Maguire <camm@maguirefamily.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Camm Maguire <camm@maguirefamily.org>
Patchwork: https://patchwork.linux-mips.org/patch/1750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following section mismatch:
WARNING: arch/mips/built-in.o(.text+0xc): Section mismatch in reference from the
function jz4740_init_cmdline() to the variable .init.data:arcs_cmdline
While were at it, make jz4740_init_cmdline static as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We never needed that (->regs[2] is overwritten on return from syscall paths
with return value of syscall, so storing it there early made no sense) and
with new restart logics since d27240bf7e61d2656de18e158ec910a902030847 it
has become really bad - we lose the original syscall number before the
place where we decide that we might need a syscall restart.
Note that for child we do need the assignment to regs[2] - it won't go
through the normal return from syscall path.
[Ralf: Issue found and reported by Lluís; initial investigations by me;
bug finally found and patch by Al; testing by me and Lluís.]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Lluís Batlle i Rossell <viriketo@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The perf hardware pmu got initialized at various points in the boot,
some before early_initcall() some after (notably arch_initcall).
The problem is that the NMI lockup detector is ran from early_initcall()
and expects the hardware pmu to be present.
Sanitize this by moving all architecture hardware pmu implementations to
initialize at early_initcall() and move the lockup detector to an explicit
initcall right after that.
Cc: paulus <paulus@samba.org>
Cc: davem <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290707759.2145.119.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.infradead.org/mtd-2.6: (82 commits)
mtd: fix build error in m25p80.c
mtd: Remove redundant mutex from mtd_blkdevs.c
MTD: Fix wrong check register_blkdev return value
Revert "mtd: cleanup Kconfig dependencies"
mtd: cfi_cmdset_0002: make sector erase command variable
mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips
mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode
mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one
block2mtd: dubious assignment
P4080/mtd: Fix the freescale lbc issue with 36bit mode
P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
mtd: phram: use KBUILD_MODNAME
mtd: OneNAND: S5PC110: Fix double call suspend & resume function
mtd: nand: fix MTD_MODE_RAW writes
jffs2: use kmemdup
mtd: sm_ftl: cosmetic, use bool when possible
mtd: r852: remove useless pci powerup/down from suspend/resume routines
mtd: blktrans: fix a race vs kthread_stop
mtd: blktrans: kill BKL
mtd: allow to unload the mtdtrans module if its block devices aren't open
...
Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
Conflicts:
drivers/mtd/mtd_blkdevs.c
Merge Grant's device-tree bits so that we can apply the subsequent fixes.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Selects HAVE_C_RECORDMCOUNT to use the C version of the recordmcount
intead of the old Perl Version of recordmcount.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
LKML-Reference: <bb99009a9ac79d3f55a8c8bf1c8bd2bc0e1f160e.1288176026.git.wuzhangjin@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TASK_SIZE macro should reflect the size of a user process virtual
address space. Previously for 64-bit kernels, this was not the case.
The immediate cause of pain was in
hugetlbfs/inode.c:hugetlb_get_unmapped_area() where 32-bit processes
trying to mmap a huge page would be served a page with an address
outside of the 32-bit address range. But there are other uses of
TASK_SIZE in the kernel as well that would like an accurate value.
The new definition is nice because it now makes TASK_SIZE and
TASK_SIZE_OF() yield the same value for any given process.
For 32-bit kernels there should be no change, although I did factor
out some code in asm/processor.h that became identical for the 32-bit and
64-bit cases.
__UA_LIMIT is now set to ~((1 << SEGBITS) - 1) for 64-bit kernels.
This should eliminate the possibility of getting a
AddressErrorException in the kernel for addresses that pass the
access_ok() test.
With the patch applied, I can still run o32, n32 and n64 processes,
and have an o32 shell fork/exec both n32 and n64 processes.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1701/
Some MIPS32R1 processors implement UserLocal (RDHWR $29) to accelerate
programs that make extensive use of thread-local storage. Therefore,
setting up the HWRENA register should not depend on cpu_has_mips_r2.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
On many of the newer MIPS32 cores, CP0 CONFIG2 bit 12 (L2B) indicates
that the L2 cache is disabled and therefore Linux should not attempt
to use it.
[Ralf: Moved the code added by Kevin's original patch into a separate
function that can easily be replaced for platforms that need more a
different probe.]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1723/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
