The lcd0 node for am437x-sk-evm.dts contains bad LCD timings, and while
they seem to work with a quick test, doing for example blank/unblank
will give you a black display.
This patch updates the timings to the 'typical' values from the LCD spec
sheet.
Also, the compatible string is completely bogus, as
"osddisplays,osd057T0559-34ts" is _not_ a 480x272 panel. The panel on
the board is a newhaven one. Update the compatible string to reflect
this. Note that this hasn't caused any issues, as the "panel-dpi"
matches the driver.
Cc: <stable@vger.kernel.org> # v3.17+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the latest Data Manual, for newer samples,
the nominal voltage required for VDD_CORE at OPP_NOM can be
upto 1.06V which was 1.03V earlier.
Update the regulator max voltage constraint for SMPS7,
connected to VDD_CORE, to meet this requirement.
Document reference:
DRA74 Data Manual, SPRS857M - Dec 2012, Revised Oct 2014.
DRA72 Data Manual, SPRS906G - Dec 2012, revised Oct 2014.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The max expected voltage for VDD_GPU, connected to SMPS6, is 1.25V.
Correct regulator max voltage constraint to meet this requirement.
Document reference: DRA74 Data Manual, SPRS857M - Dec 2012,
Revised Oct 2014.
Fixes: c56a831ca4 ("ARM: dts: DRA7: Add TPS659038 PMIC nodes")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ES1.2 is a minor variant of ES1.1. Major changes since ES1.1 are
updating ROM for fixing the following boot modes:
- NAND boot
- UART boot
- Ethernet boot
- USB HOST/Client boot
This patch adds ID support for AM437x ES1.2 silicon.
There are no additional kernel fixes required for ES1.2 silicon.
Latest Technical Documentation can be found here:
http://www.ti.com/lsds/ti/arm/sitara_arm_cortex_a_processor/arm_cortex_a9_core/am437x_arm_cortex_a9/tech_docs.page
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.
Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.
While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.
Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f4d809ec55b6 ("ARM: dts: Fix gpmc timings for omap 2430sdp")
added GPMC timings for 2430sdp. This however broke the Ethernet
for some versions of u-boot using a different L3 clock frequency:
set_gpmc_timing_reg: GPMC error! CS5: cs_rd_off: 233 ns, 39 ticks > 31
omap-gpmc 6e000000.gpmc: failed to set gpmc timings for: ethernet
This is because the smsc91x timings from 1.1.4 u-boot overflow the
GPMC registers when booted with 1.1.3 version of u-boot.
Let's fix this issue by using the better timings from u-boot 1.1.3
as they also work on 1.1.4 and are faster.
Note that so far the attempts over the years to calculate the GPMC
timings on the SDP boards have failed probably because of the
unknown latencies added by the FPGA on the debug boards.
Reported-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
This is a collection of the various changes to defconfig files,
most importantly enabling some additional platforms in the
multi_v7_defconfig file. These are split out into a separate
branch to avoid most of the merge conflicts in the defconfig
files.
This also touches 12 other defconfig files for shmobile,
at91, hisilicon, keystone, mvebu, omap, and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=brXv
-----END PGP SIGNATURE-----
Merge tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig changes from Arnd Bergmann:
"This is a collection of the various changes to defconfig files, most
importantly enabling some additional platforms in the
multi_v7_defconfig file. These are split out into a separate branch
to avoid most of the merge conflicts in the defconfig files.
This also touches 12 other defconfig files for shmobile, at91,
hisilicon, keystone, mvebu, omap, and tegra"
* tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: omap2plus_defconfig: enable ECAP and EHRPWM
ARM: omap2plus_defconfig: enable XHCI
ARM: omap2plus_defconfig: enable AM33XX SoC sound
ARM: omap2plus_defconfig: enable EDT FT5X06 touchscreen
ARM: omap2plus_defconfig: remove unwanted ethernet drivers
ARM: multi_v7_defconfig: enable MAX77686 PMIC drivers for exynos4412-prime based SoCs
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
ARM: defconfig: imx_v6_v7_defconfig updates
ARM: multi_v7_defconfig: add driver support for hix5hd2
ARM: exynos_defconfig: Use 16 minors per MMC block device
ARM: mvebu: add MTD_BLOCK to mvebu_v7_defconfig
ARM: mvebu: enable i2c device in mvebu_v7_defconfig
ARM: mvebu: re-enable SDHCI driver for Armada 38x SoC in v7 defconfig
ARM: tegra: Regenerate default configuration
ARM: multi_v7_defconfig: Enable cgroups
ARM: multi_v7_defconfig: Enable Broadcom Cygnus
...
The GPMC driver has traditionally been considered a part of the
OMAP platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver
that does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U4Fz
-----END PGP SIGNATURE-----
Merge tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC/OMAP GPMC driver cleanup and move from Arnd Bergmann:
"The GPMC driver has traditionally been considered a part of the OMAP
platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver that
does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups"
* tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
ARM: OMAP2+: Remove unnecesary include in GPMC driver
ARM: OMAP2+: Drop board file for 3430sdp
ARM: OMAP2+: Drop board file for ti8168evm
ARM: OMAP2+: Drop legacy code for gpmc-smc91x.c
ARM: OMAP2+: Require proper GPMC timings for devices
ARM: OMAP2+: Show bootloader GPMC timings to allow configuring the .dts file
ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select
ARM: OMAP2+: gpmc: Sanity check GPMC fck on probe
ARM: OMAP2+: gpmc: Keep Chip Select disabled while configuring it
ARM: OMAP2+: gpmc: Always enable A26-A11 for non NAND devices
ARM: OMAP2+: gpmc: Error out if timings fail in gpmc_probe_generic_child()
ARM: OMAP2+: gpmc: Print error message in set_gpmc_timing_reg()
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVIcjyGCrR//JCVInAQJJCRAA1Tm+HZGiAiTvXEAcm/T9tIA08uqtawHt
cqyEAUyrnE8QxE4EhUd2pTw4EunVusqKF5EsDxOzw7b3ukUdLAWZE7bqBOSIJLqn
hrfsQQ8dXLbyC7T/CHPnBVeM+pn9LiIc9qzpZ0YToiMnHBBI4vKFQntBjd31yoRE
hN08I6AmDjQolOzzlqR1fuM0uZaKiHIcytdauTt3Vfqgg7FTHcTy3u1kClHTR1Lp
m/KuDothGpR5OKjSnUQz7EO5V3KJEnaKey8z2xM1a7DLLAvJ6r2+DUaDopv9Dbz1
W/V3H7fi5tLvillVa8xmlmzqWZbPc1xw8MWqvHZSWIMRZqloAHpC1VWKn0ZuH4SW
5Bj4ubSrpYjJxjKYfrxtjmuzru3A2jWBNTSP5A4nsny0C3AUsXkfRmRS0VNdegF8
sUdQ1MF8vEMpQT3QPH88+ccFHeIgqbcayhKqLPf7r8q0kwlym5N7Y2amU2A/O6qz
+324r+yzfSA70VgJZ5EhXxWVDOPB4Lc8EtoWnH6T/kjncIMwzEsbEbyB3X1OaREW
pVn3PNo06VjHLYoiHX+8G99pOFR/JZvaQs6jGCXLs+Orjp5WfP+kafkWqcB5GAKU
Pfd3AQsl6rKAITdu0XsTdPiICNS4CmBiWYPepQsTa3pQaNgB7fwZNQKelNRIdGc+
dF1lnQ7CXLQ=
=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
- Consolidation and cleanups.
- Some improvements regarding error handling.
- Increase maximum amount of block devices.
- Use correct OCR mask for SDIO when restoring power.
- Fix prepared requests while doing BKOPS.
- Convert to modern PM ops.
- Add mmc_send_tuning() API and convert some hosts to use it.
MMC host:
- toshsd: New Toshiba PCI SD controller driver.
- sdhci: 64-bit ADMA support.
- sdhci: Some regulator fixes.
- sdhci: HS400 support.
- sdhci: Various fixes cleanups.
- atmel-mci: Modernization and cleanups.
- atmel-mci: Runtime PM support.
- omap_hsmmc: Modernization and cleanups.
- omap_hsmmc: Fix UHS card with DDR50 support.
- dw_mmc: Support for ARM64 and Exynos 7 variant.
- dw_mmc: Add support for IMG Pistachio variant.
- dw_mmc: Various fixes and cleanups.
- mvsdio: DMA fixes.
- mxs-mmc: Modernization and cleanups.
- mxcmmc: Various fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ODSj
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Consolidation and cleanups.
- Some improvements regarding error handling.
- Increase maximum amount of block devices.
- Use correct OCR mask for SDIO when restoring power.
- Fix prepared requests while doing BKOPS.
- Convert to modern PM ops.
- Add mmc_send_tuning() API and convert some hosts to use it.
MMC host:
- toshsd: New Toshiba PCI SD controller driver.
- sdhci: 64-bit ADMA support.
- sdhci: Some regulator fixes.
- sdhci: HS400 support.
- sdhci: Various fixes cleanups.
- atmel-mci: Modernization and cleanups.
- atmel-mci: Runtime PM support.
- omap_hsmmc: Modernization and cleanups.
- omap_hsmmc: Fix UHS card with DDR50 support.
- dw_mmc: Support for ARM64 and Exynos 7 variant.
- dw_mmc: Add support for IMG Pistachio variant.
- dw_mmc: Various fixes and cleanups.
- mvsdio: DMA fixes.
- mxs-mmc: Modernization and cleanups.
- mxcmmc: Various fixes"
* tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc: (126 commits)
mmc: sdhci-msm: Convert to mmc_send_tuning()
mmc: sdhci-esdhc-imx: Convert to mmc_send_tuning()
mmc: core: Let mmc_send_tuning() to take struct mmc_host* as parameter
mmc: queue: Improve error handling during allocation of bounce buffers
mmc: sdhci-acpi: Add two host capabilities for Intel
mmc: sdhci-pci: Add two host capabilities for BYT
mmc: sdhci-acpi: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
mmc: sdhci-pci: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC to BYT
mmc: atmel-mci: use probe deferring if dma controller is not ready yet
mmc: atmel-mci: stop using specific initcall
mmc: atmel-mci: remove __init/__exit attributes
mmc: atmel-mci: remove useless DMA stuff for non-dt devices
mmc: omap_hsmmc: Fix UHS card with DDR50 support
mmc: core: add core-level function for sending tuning commands
mmc: core: hold SD Clock before CMD11 during Signal
mmc: mxs-mmc: Check for clk_prepare_enable() error
mmc: mxs-mmc: Propagate the real error
mmc: mxs-mmc: No need to do NULL check on 'iores'
mmc: dw_mmc: Add support for IMG Pistachio
mmc: mxs-mmc: Simplify PM hooks
...
The at91 cleanups changed a lot of files, this merges in the
latest cleanups to resolve the conflicts
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/clock.c
arch/arm/mach-at91/clock.h
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This resolves a nonobvious merge conflict that I got wrong the
first time.
* brcm/stb-smp-uart:
bus: brcmstb_gisb: save and restore GISB timeout
bus: brcmstb_gisb: register the fault code hook
ARM: brcmstb: Kconfig: drop unneeded symbol selections
ARM: brcmstb: reintroduce SMP support
ARM: brcmstb: add debug UART for earlyprintk support
Conflicts:
drivers/bus/brcmstb_gisb.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
This will enable use of physical arch timers on rk3288, where each
core comes out of reset with a different virtual offset. Using
physical timers will help with SMP booting on coreboot and older
u-boot and should also allow suspend-resume and cpu-hotplug to work on
all firmwares.
Firmware which does initialize the cpu registers properly at boot and
cpu-hotplug can remove this property from the device tree.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Many of AM335x and AM437x hook backlight to
one of these two devices. By enabling their
drivers we make sure pwm-backlight can do
its thing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AM437x devices have a DWC3 IP inside of them.
The host side implementation of DWC3 is XHCI
compliant. By enabling XHCI driver, we get
the USB host port on AM437x Starter Kit working
out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Without this, sound on AM437x Starter Kit will
not work.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AM437x Starter Kit ships with EDT FT5306 touchscreen
device. By enabling the driver we make sure touchscreen
will work out of the box.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
None of these drivers are known to be used on
any platform supported by omap2plus_defconfig,
by removing them we get a slight smaller kernel.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We now have the physical-timers patches lined up as a dependency in this same
branch, so we can revert the temporary disablement.
This reverts commit b77d43943e.
Signed-off-by: Olof Johansson <olof@lixom.net>
These are a pre-req to get rk3288 SMP to work with some firmwares, so merge
it in here as well as in next/drivers.
* clocksource/physical-timers:
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
* clocksource/physical-timers:
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
This is a bug fix for using physical arch timers when
the arch_timer_use_virtual boolean is false. It restores the
arch_counter_get_cntpct() function after removal in
0d651e4e "clocksource: arch_timer: use virtual counters"
We need this on certain ARMv7 systems which are architected like this:
* The firmware doesn't know and doesn't care about hypervisor mode and
we don't want to add the complexity of hypervisor there.
* The firmware isn't involved in SMP bringup or resume.
* The ARCH timer come up with an uninitialized offset between the
virtual and physical counters. Each core gets a different random
offset.
* The device boots in "Secure SVC" mode.
* Nothing has touched the reset value of CNTHCTL.PL1PCEN or
CNTHCTL.PL1PCTEN (both default to 1 at reset)
One example of such as system is RK3288 where it is much simpler to
use the physical counter since there's nobody managing the offset and
each time a core goes down and comes back up it will get reinitialized
to some other random value.
Fixes: 0d651e4e65 ("clocksource: arch_timer: use virtual counters")
Cc: stable@vger.kernel.org
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The imx6 PM code seems to be quite creative in its use of irq_data,
using something that is very much a hardware interrupt number where
we expect a virtual one. Yes, it worked so far, but that's only
luck, and it will definitely explode in 3.19.
Fix it by using a pair of helper functions that deal with the
actual hardware.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
mach-imx directly references to the irq field in
struct irq_data, and uses this to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different.
Just replacing all instances of irq with hwirq fixes the issue.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=epqY
-----END PGP SIGNATURE-----
Merge tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux into next/dt
Merge "ARM: BCM5301X: DT changes for v3.19 #2" from Hauke Mehrtens:
ARM: BCM5301X: dts updates
This adds the IRQ number to the main dts file and some new dts files
for newly added devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* tag 'bcm5301x-dt-2014-12-04' of https://github.com/hauke/linux:
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables the MAX77686 PMIC drivers in the multi_v7_defconfig used
on exynos4412-prime family of SoCs [1]. The exynos4412-prime based boards
are producing the following runtime errors only on the multi_v7_defconfig [2]:
kern.err: deviceless supply vdd_arm not found, using dummy regulator
kern.err: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage to 1287500
kern.err: cpufreq: __target_index: Failed to change cpu frequency: -22
I reviewed the exynos_defconfig, which does not produce these runtime
errors. It was obvious that the exynos_defconfig has the PMIC drivers
enabled, whereas the multi_v7_defconfig does not. This patch has been tested
on a odroid-u2 and a odroid-u3 board. It has resolved the runtime errors.
Therefore, I purpose we enabled these drivers in the multi_v7_defconfig.
[1] http://www.hardkernel.com/main/products/prdt_info.php?g_code=G135270682824
[2] http://storage.armcloud.us/kernel-ci/mainline/v3.18-rc7-48-g7cc78f8/arm-multi_v7_defconfig/lab-tbaker-00/boot-exynos4412-odroidu3.html
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- removal of now dead code and AT91-specific driver
- removal of !DT initialization in some core AT91 drivers
- simplification of Kconfig DT board file selection: now automatic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUgJyWAAoJEAf03oE53VmQ/o0IAK56Q3+fTgTi5uT5RwvYpFI+
U3Zosn6UNe2kxNpJMtsaWM7vCrmMdHb6LPaf4dy66e4tL4sBhYmyXhWU9UTEiwtw
l3Y5QCVqOpOKtVc/cYOtYtHYkcHyqyVa0qRb3XITvwpUeG0iJxrtcMRYTlDUpKD4
pJEfRK2CcHUrNXnnOcHkYaj0d5dXlJ2wJeGiAkCI0iuVWh4f44ipOAPI/0vZLO39
OIFBZRwXmQpWwncLlbVrwScK7ZD8I/qersrH72c3RdIBp0K6tbuNSXkLFL7pZhp0
pJ1Yh44HLmAklx4G0Ui0h4fWu5wMCrT7YBUXZ3Jv+RTRwW1Sr9pAhZdGxXtAYXo=
=CEE6
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup5' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/cleanup
Pull "Fifth batch of cleanup/SoC for 3.19" from Nicolas Ferre:
- removal of now dead code and AT91-specific driver
- removal of !DT initialization in some core AT91 drivers
- simplification of Kconfig DT board file selection: now automatic
* tag 'at91-cleanup5' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUgI0MAAoJEAf03oE53VmQauEH/38kPqGBa4Me4pBhvA9xMsDH
8cCuJ3Mpo14NiEADu56QY5dG5qnVfA1F0Mn+Xs/1iR8b9TQPoHIs7D8BO25Yb8vJ
KdkeIfUBgFl8GV8W6QfABRf6Mr2aidVknBNBE/hsUStDkU3hNU0i3p/kn87f/QH8
SuFXao18pqqQJ+pVigMRyEWbfGXYYUcJoKQYg8Us/LNHLP4Zl3PSerqAhPnvjts6
QrQvT6t4ijCixvLs8/baEwFNylUWarRbziVh6GPmzBrOl8KL93NPwnGXcCbE9zXS
tVjcXYgRcq9h7rUp83AqxnxWPbKdJnD3S91huwhikZirt7+CcgulAbe5BLYcnnE=
=FZRZ
-----END PGP SIGNATURE-----
Merge tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
Pull "First batch of defconfigs for AT91 / 3.19:" from Nicolas Ferre:
- use NEON for all C-A5, neon code handles the !NEON case
- add new XDMA driver
- add some useful drivers as we only have a single defconfig for all
AT91SAM9/RM9200
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUffEUAAoJEPOmecmc0R2Bk4QH/0O8+misF7MM3/EX0UOicb09
zrrVaPfH8GKHz3NlXGNZhIgy1coNoElBmdWPEb+XI+tRI3vKcyHtsJp78XHYupBl
yHFXjRYw4dHwwc08cQRDzf8qfWFpTnKX/gSBhgn5+kuIvylalLmnY8RjYtuQcaYW
DEc5B8eEMmmDH1Y3UBat+JOIJZY4NWxc9zmK+wRuMtcLt8ieCmgOWVMBjl8BerAe
Vdi0EM3YicA/HDzPVNq3xQK6cUtWDfKSFvkJhwc9Q40Yl4LQaOf2YMA2sZ/4+Qnl
F1LLJtJFMo9A0vECDJIfleXJRXnq0VjVp1Mn18Do8J6zsazzS94ppSDyk5EliVg=
=jMaL
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "last dts changes for 3.19" from Jason Cooper:
- rk3288 thermal driver that got accepted into the thermal tree
- mmc fifo sizes for Cortex-A9 SoCs
- labels for the leds on the RadxaRock
- core system supply for the Marsboard
* tag 'v3.19-rockchip-dts4' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: dts: rockchip: enable thermal on rk3288-evb board
ARM: dts: rockchip: add main thermal info to rk3288
ARM: dts: rockchip: add RK3288 Thermal data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the selection of the new PWM driver using TC Blocks. This driver is
useful so we enable it in both sama5 and at91_dt defconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the Atmel eXtended DMA Controller driver option. This driver is first used
on SAMA5D4 SoCs and only relevant in sama5_defconfig file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add neon support for sama5d4 and large blocks/files support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adjusts the registration of the cpufreq-dt driver in the
mvebu platform to indicate to the cpufreq driver that the platform has
independent clocks for each CPU.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=R4je
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "ARM: tegra: IOMMU support for v3.19" from Thierry Reding:
This adds the driver pieces required for IOMMU support on Tegra30,
Tegra114 and Tegra124.
* tag 'tegra-for-3.19-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: Add NVIDIA Tegra memory controller support
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
powerpc/iommu: Rename iommu_[un]map_sg functions
iommu: Improve error handling when setting bus iommu
iommu: Do more input validation in iommu_map_sg()
iommu: Add iommu_map_sg() function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tomi Valkeinen