[ Upstream commit 30d24faba0 ]
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e4e9ec650 ]
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f99 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 556699341e ]
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db21997379 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e62458e394 ]
The new string should have enough space for the original string and the
back slashes IMHO.
Fixes: fbc2844e84 ("perf vendor events: Use more flexible pattern matching for CPU identification for mapfile.csv")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: William Cohen <wcohen@redhat.com>
Link: http://lore.kernel.org/lkml/20200903152510.489233-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0c20d38af ]
The realtime flag only applies to the data fork, so don't use the
realtime block number checks on the attr fork of a realtime file.
Fixes: 30b0984d91 ("xfs: refactor bmap record validation")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb06748207 ]
In cc97ab235f ("MIPS: Simplify FP context initialization), init_fp_ctx
just initialize the fp/msa context, and own_fp_inatomic just restore
FCSR and 64bit FP regs from it, but miss MSACSR and upper MSA regs for
MSA, so MSACSR and MSA upper regs's value from previous task on current
cpu can leak into current task and cause unpredictable behavior when MSA
context not initialized.
Fixes: cc97ab235f ("MIPS: Simplify FP context initialization")
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb0f3bc463 ]
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77f4689de1 ]
epoll_loop_check_proc() can run into a file already committed to destruction;
we can't grab a reference on those and don't need to add them to the set for
reverse path check anyway.
Tested-by: Marc Zyngier <maz@kernel.org>
Fixes: a9ed4a6560 ("epoll: Keep a reference on files added to the check list")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbedcb044e ]
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39c0a53b11 ]
perf_event.h has macros that define the field offsets in the data_src
bitmask in perf records. The SNOOPX and REMOTE offsets were both 37.
These are distinct fields, and the bitfield layout in perf_mem_data_src
confirms that SNOOPX should be at offset 38.
Committer notes:
This was extracted from a larger patch that also contained kernel
changes.
Fixes: 52839e653b ("perf tools: Add support for printing new mem_info encodings")
Signed-off-by: Al Grant <al.grant@arm.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/9974f2d0-bf7f-518e-d9f7-4520e5ff1bb0@foss.arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 192f6c29bb ]
If the driver has to unbind from the controller for an early failure
before the subsystem has been set up, there won't be a subsystem holding
the controller's instance, so the controller needs to free its own
instance in this case.
Fixes: 733e4b69d5 ("nvme: Assign subsys instance from first ctrl")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e37988db ]
The way 'spin_lock()' and 'spin_lock_irqsave()' are used is not consistent
in this function.
Use 'spin_lock_irqsave()' also here, as there is no guarantee that
interruptions are disabled at that point, according to surrounding code.
Fixes: a97ec51b37 ("nvmet_fc: Rework target side abort handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee92118355 ]
Frontend callback reports EAGAIN to nfnetlink to retry a command, this
is used to signal that module autoloading is required. Unfortunately,
nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets
full, so it enters a busy-loop.
This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and
to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast()
since this is always MSG_DONTWAIT in the existing code which is exactly
what nlmsg_unicast() passes to netlink_unicast() as parameter.
Fixes: 96518518cc ("netfilter: add nftables")
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa4505675e ]
When stdout output from the selftests tool 'test_maps' gets redirected
into e.g file or pipe, then the output lines increase a lot (from 21
to 33949 lines). This is caused by the printf that happens before the
fork() call, and there are user-space buffered printf data that seems
to be duplicated into the forked process.
To fix this fflush() stdout before the fork loop in __run_parallel().
Fixes: 1a97cf1fe5 ("selftests/bpf: speedup test_maps")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/159842985651.1050885.2154399297503372406.stgit@firesoul
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b30063976f ]
The check for a required control in the request was missing a call to
v4l2_ctrl_request_hdl_put() in the error path. Fix it.
Fixes: 50e761516f ("media: platform: Add Cedrus VPU decoder driver")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e7c8fb894 ]
The check for a required control in the request was missing a call to
v4l2_ctrl_request_hdl_put(), so the control request object was never
released.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 997deb811b ("media: vicodec: Add support for stateless decoder.")
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4020438fa ]
The boundary test for the fixed-offset parts of xfs_attr_sf_entry in
xfs_attr_shortform_verify is off by one, because the variable array
at the end is defined as nameval[1] not nameval[].
Hence we need to subtract 1 from the calculation.
This can be shown by:
# touch file
# setfattr -n root.a file
and verifications will fail when it's written to disk.
This only matters for a last attribute which has a single-byte name
and no value, otherwise the combination of namelen & valuelen will
push endp further out and this test won't fail.
Fixes: 1e1bbd8e7e ("xfs: create structure verifier function for shortform xattrs")
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cce90b93 ]
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b148bb238c ]
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df3875ec55 ]
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbbfa96ad9 ]
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c2d77408 ]
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99d469fc64 ]
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca56 ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b274e47d9e ]
During a dump, this attribute is essential, it enables the userspace to
know on which interface the context is linked to.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0661cef675 ]
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 137bd11090 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2d79cd887 ]
When devm_gpiod_get_optional() fails, bus should be
freed just like when of_mdiobus_register() fails.
Fixes: 1bddd96cba ("net: arc_emac: support the phy reset for emac driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1838d6c62f ]
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ef1fc5730 ]
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 100e3345c6 ]
hns_nic_dev_probe allocates ndev, but not free it on
two error handling paths, which may lead to memleak.
Fixes: 63434888aa ("net: hns: net: hns: enet adds support of acpi")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e105e6afa ]
Following bug was reported via irc:
nft list ruleset
set knock_candidates_ipv4 {
type ipv4_addr . inet_service
size 65535
elements = { 127.0.0.1 . 123,
127.0.0.1 . 123 }
}
..
udp dport 123 add @knock_candidates_ipv4 { ip saddr . 123 }
udp dport 123 add @knock_candidates_ipv4 { ip saddr . udp dport }
It should not have been possible to add a duplicate set entry.
After some debugging it turned out that the problem is the immediate
value (123) in the second-to-last rule.
Concatenations use 32bit registers, i.e. the elements are 8 bytes each,
not 6 and it turns out the kernel inserted
inet firewall @knock_candidates_ipv4
element 0100007f ffff7b00 : 0 [end]
element 0100007f 00007b00 : 0 [end]
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9125df85 ]
This should be NFTA_LIST_UNSPEC instead of NFTA_LIST_UNPEC, all other
similar attribute definitions are postfixed with _UNSPEC.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f03bf43ee ]
Kernel sends an empty NFTA_SET_USERDATA attribute with no value if
userspace adds a set with no NFTA_SET_USERDATA attribute.
Fixes: e6d8ecac9e ("netfilter: nf_tables: Add new attributes into nft_set to store user data.")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61d7437ed1 ]
The AMD eMMC Controller can only use the tuned clock while in HS200 and
HS400 mode. If we switch to a different mode, we need to disable the
tuned clock. If we have previously performed tuning and switch back to
HS200 or HS400, we can re-enable the tuned clock.
Previously the tuned clock was not getting disabled when switching to
DDR52 which is part of the HS400 tuning sequence.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200819125832.v2.1.Ie8f0689ec9f449203328b37409d1cf06b565f331@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e14f633b66 ]
The initialization done by bmips_cpu_setup() typically affects both
threads of a given core, on 7435 which supports 2 cores and 2 threads,
logical CPU number 2 and 3 would not run this initialization.
Fixes: 738a3f7902 ("MIPS: BMIPS: Add early CPU initialization code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbfc95f98f ]
When the BMIPS generic cpu-feature-overrides.h file was introduced,
cpu_has_inclusive_caches/MIPS_CPU_INCLUSIVE_CACHES was not set for
BMIPS5000 CPUs. Correct this when we have initialized the MIPS secondary
cache successfully.
Fixes: f337967d6d ("MIPS: BMIPS: Add cpu-feature-overrides.h")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d4adfaf65 ]
Fix rxrpc_kernel_get_srtt() to indicate the validity of the returned
smoothed RTT. If we haven't had any valid samples yet, the SRTT isn't
useful.
Fixes: c410bf0193 ("rxrpc: Fix the excessive initial retransmission timeout")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68528d937d ]
Keep the ACK serial number in a variable in rxrpc_input_ack() as it's used
frequently.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cef8e2c5a ]
The reurn value of of_find_device_by_node() is not checked, thus null
pointer dereference will be triggered if of_find_device_by_node()
failed.
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200817115728.1706719-2-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 279e89b228 ]
batadv_bla_send_claim() gets called from worker thread context through
batadv_bla_periodic_work(), thus netif_rx_ni needs to be used in that
case. This fixes "NOHZ: local_softirq_pending 08" log messages seen
when batman-adv is enabled.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8bf0c0164 ]
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
Fixes: 9323158ef9 ("batman-adv: OGMv2 - implement originators logic")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 303216e76d ]
The gateway client code can try to optimize the delivery of DHCP packets to
avoid broadcasting them through the whole mesh. But also transmissions to
the client can be optimized by looking up the destination via the chaddr of
the DHCP packet.
But the chaddr is currently only done when chaddr is fully inside the
non-paged area of the skbuff. Otherwise it will not be initialized and the
unoptimized path should have been taken.
But the implementation didn't handle this correctly. It didn't retrieve the
correct chaddr but still tried to perform the TT lookup with this
uninitialized memory.
Reported-by: syzbot+ab16e463b903f5a37036@syzkaller.appspotmail.com
Fixes: 6c413b1c22 ("batman-adv: send every DHCP packet as bat-unicast")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b2aa9f918 ]
of_dma_xlate callback can return ERR_PTR as well NULL in case of failure.
If error code is returned (not NULL) then the route should be released and
the router should not be registered for the channel.
Fixes: 56f13c0d95 ("dmaengine: of_dma: Support for DMA routers")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200806104928.25975-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a4c56c80f ]
Commit ef91bb196b ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d742db7003 ]
On some architectures (like ARM), virt_to_gfn cannot be used for
vmalloc'd memory because of its reliance on virt_to_phys. This patch
introduces a check for vmalloc'd addresses and obtains the PFN using
vmalloc_to_pfn in that case.
Signed-off-by: Simon Leiner <simon@leiner.me>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20200825093153.35500-1-simon@leiner.me
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67a468a4c ]
When amdgpu_display_modeset_create_props() fails, state and
state->context should be freed to prevent memleak. It's the
same when amdgpu_dm_audio_init() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef67d792a2 ]
[Why]
In dm_dp_aux_transfer() now, we forget to handle AUX_WR fail cases. We
suppose every write wil get done successfully and hence some AUX
commands might not sent out indeed.
[How]
Check if AUX_WR success. If not, retry it.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren