Similarly to R-Car E3, RZ/G2E doesn't come with automatic
transmission registers, as such it is not considered compatible
with the existing fallback bindings.
Add SoC specific binding compatibility to allow for later
support for automatic transmission.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When CONFIG_PM is disabled, this is needed to avoid a harmless
unused-function warning:
drivers/i2c/busses/i2c-nvidia-gpu.c:345:12: error: 'gpu_i2c_resume' defined but not used [-Werror=unused-function]
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch moves configuration of hardware registers used for setting
i2c client address to separate function. It is preparatory change for
next commit.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- For a repeated START condition, this controller starts data transfer
immediately after the slave address is written to the TX-FIFO.
- Once the TX-FIFO empty interrupt is asserted, the controller makes
a pause even if additional data are written to the TX-FIFO.
Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I was totally screwed up in commit eaba68785c ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.
It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba68785c.
Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.
This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.
I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.
I consulted a hardware engineer, and I got the following information:
UNIPHIER_FI2C_INT_RF
asserted at the falling edge of SCL at the 8th bit.
UNIPHIER_FI2C_INT_RB
asserted at the rising edge of SCL at the 9th (ACK) bit.
In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.
Fixes: eaba68785c ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use PM Runtime API to enable/disable clock
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should check the bus state before reinitializing the IP core.
Otherwise, the internal bus busy state which also tracks multi-master
activity is lost.
Credits go to the Renesas BSP team for suggesting this change.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ae481cc139 ("i2c: rcar: fix resume by always initializing registers before transfer")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the controller can only do 4 byte reads, this needs to be applied for
the read-part of combined messages, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
As described in Documentation/i2c/fault-codes.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Add support for the IIC code for the r8a77990 (R-Car E3).
It is not considered compatible with existing fallback bindings
due to the documented absence of automatic transmission registers.
These registers are currently not used by the driver and
thus the provides the same behaviour for "renesas,iic-r8a77990" and
"renesas,rcar-gen3-iic". The point of declaring incompatibility is
to allow for automatic transmission register support to be added to
"renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is already done for us internally by the signal machinery.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Latest NVIDIA GPU card has USB Type-C interface. There is a
Type-C controller which can be accessed over I2C.
This driver adds I2C bus driver to communicate with Type-C controller.
I2C client driver will be part of USB Type-C UCSI driver.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: kept Makefile sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4oYh
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede)"
* tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: Add depends on IOSF_MBI to Kconfig entry
i2c: designware: Cleanup bus lock handling
ACPI / PMIC: xpower: Block P-Unit I2C access during read-modify-write
x86: baytrail/cherrytrail: Rework and move P-Unit PMIC bus semaphore code
Pull i2c updates from Wolfram Sang:
"I2C has not so much stuff this time. Mostly driver enablement for new
SoCs, some driver bugfixes, and some cleanups"
* 'i2c/for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (35 commits)
MAINTAINERS: add maintainer for Renesas RIIC driver
i2c: sh_mobile: Remove dummy runtime PM callbacks
i2c: uniphier-f: fix race condition when IRQ is cleared
i2c: uniphier-f: fix occasional timeout error
i2c: uniphier-f: make driver robust against concurrency
i2c: i2c-qcom-geni: Simplify irq handler
i2c: i2c-qcom-geni: Simplify tx/rx functions
i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers
i2c: mux: mlxcpld: simplify code to reach the adapter
i2c: mux: ltc4306: simplify code to reach the adapter
i2c: mux: pca954x: simplify code to reach the adapter
i2c: core: remove level of indentation in i2c_transfer
i2c: core: remove outdated DEBUG output
i2c: zx2967: use core to detect 'no zero length' quirk
i2c: tegra: use core to detect 'no zero length' quirk
i2c: qup: use core to detect 'no zero length' quirk
i2c: omap: use core to detect 'no zero length' quirk
i2c: Convert to using %pOFn instead of device_node.name
i2c: brcmstb: Allow enabling the driver on DSL SoCs
eeprom: at24: fix unexpected timeout under high load
...
Platform drivers don't need dummy runtime PM callbacks that just return
success and non-NULL pm pointer in their struct device_driver in order
to have runtime PM happening. This has changed since following commits:
05aa55dddb ("PM / Runtime: Lenient generic runtime pm callbacks")
543f2503a9 ("PM / platform_bus: Allow runtime PM by default")
8b313a38ec ("PM / Platform: Use generic runtime PM callbacks directly")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current IRQ handler clears all the IRQ status bits when it bails
out. This is dangerous because it might clear away the status bits
that have just been set while processing the current handler. If this
happens, the IRQ event for the latest transfer is lost forever.
The IRQ status bits must be cleared *before* the next transfer is
kicked.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, a timeout error could happen at a repeated START condition.
For a (non-repeated) START condition, the controller starts sending
data when the UNIPHIER_FI2C_CR_STA bit is set. However, for a repeated
START condition, the hardware starts running when the slave address is
written to the TX FIFO - the write to the UNIPHIER_FI2C_CR register is
actually unneeded.
Because the hardware is already running before the IRQ is enabled for
a repeated START, the driver may miss the IRQ event. In most cases,
this problem does not show up since modern CPUs are much faster than
the I2C transfer. However, it is still possible that a context switch
happens after the controller starts, but before the IRQ register is
set up.
To fix this,
- Do not write UNIPHIER_FI2C_CR for repeated START conditions.
- Enable IRQ *before* writing the slave address to the TX FIFO.
- Disable IRQ for the current CPU while queuing up the TX FIFO;
If the CPU is interrupted by some task, the interrupt handler
might be invoked due to the empty TX FIFO before completing the
setup.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is unlikely to happen, but it is possible for a CPU to enter
the interrupt handler just after wait_for_completion_timeout() has
expired. If this happens, the hardware is accessed from multiple
contexts concurrently.
Disable the IRQ after wait_for_completion_timeout(), and do nothing
from the handler when the IRQ is disabled.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that most of the special Bay- / Cherry-Trail bus lock handling has
been moved to the iosf_mbi code we can simplify the remaining code a bit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some BYT/CHT systems the SoC's P-Unit shares the I2C bus with the
kernel. The P-Unit has a semaphore for the PMIC bus which we can take to
block it from accessing the shared bus while the kernel wants to access it.
Currently we have the I2C-controller driver acquiring and releasing the
semaphore around each I2C transfer. There are 2 problems with this:
1) PMIC accesses often come in the form of a read-modify-write on one of
the PMIC registers, we currently release the P-Unit's PMIC bus semaphore
between the read and the write. If the P-Unit modifies the register during
this window?, then we end up overwriting the P-Unit's changes.
I believe that this is mostly an academic problem, but I'm not sure.
2) To safely access the shared I2C bus, we need to do 3 things:
a) Notify the GPU driver that we are starting a window in which it may not
access the P-Unit, since the P-Unit seems to ignore the semaphore for
explicit power-level requests made by the GPU driver
b) Make a pm_qos request to force all CPU cores out of C6/C7 since entering
C6/C7 while we hold the semaphore hangs the SoC
c) Finally take the P-Unit's PMIC bus semaphore
All 3 these steps together are somewhat expensive, so ideally if we have
a bunch of i2c transfers grouped together we only do this once for the
entire group.
Taking the read-modify-write on a PMIC register as example then ideally we
would only do all 3 steps once at the beginning and undo all 3 steps once
at the end.
For this we need to be able to take the semaphore from within e.g. the PMIC
opregion driver, yet we do not want to remove the taking of the semaphore
from the I2C-controller driver, as that is still necessary to protect many
other code-paths leading to accessing the shared I2C bus.
This means that we first have the PMIC driver acquire the semaphore and
then have the I2C controller driver trying to acquire it again.
To make this possible this commit does the following:
1) Move the semaphore code from being private to the I2C controller driver
into the generic iosf_mbi code, which already has other code to deal with
the shared bus so that it can be accessed outside of the I2C bus driver.
2) Rework the code so that it can be called multiple times nested, while
still blocking I2C accesses while e.g. the GPU driver has indicated the
P-Unit needs the bus through a iosf_mbi_punit_acquire() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DMA needs to be cleaned up not only on timeout, but on all errors where
it has been setup before.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to use goto here, we can just collapse the if statement
and goto chain into multiple branches and then combine some duplicate
completion calls into one big if statement. Let's do it to clean up code
some more.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We never really look at the 'ret' local variable in these functions, so
let's remove it to make way for shorter and simpler code. Furthermore,
we can shorten some lines by adding two local variables for the SE and
the message length so that everything fits in 80 columns and testing the
'dma_buf' local variable in lieu of the 'mode' local variable. And
kernel style is to leave the return statement by itself, detached from
the rest of the function.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller. The GPU
is a PCI device and PCI devices are powered-on at the resume_noirq resume
phase.
Since the GPU power-resources need the I2C controller, recent acpi_lpss.c
changes now also power-up the LPSS I2C controllers on BYT and CHT devices
in the resume_noirq resume phase. But during this phase the IRQ of the
controller is disabled leading to these errors:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
This commit makes the i2c-designware controller set the IRQF_NO_SUSPEND
flag when requesting the interrupt on BYT and CHT devices, so that the IRQ
is left enabled during the noirq phase, fixing this.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Single patch from Wang Xin improving the read/write loop in at24
under high load.
-----BEGIN PGP SIGNATURE-----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=/lJE
-----END PGP SIGNATURE-----
Merge tag 'at24-4.20-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.20
AT24 updates for 4.20
Single patch from Wang Xin improving the read/write loop in at24
under high load.
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ARCH_BCM_63XX which is used by ARM-based DSL SoCs from Broadcom uses the
same controller, make it possible to select the STB driver and update
the Kconfig and help text a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f27727 ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f27727 ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-scmi driver crashes when the SMBus Write Block transaction is
executed:
WARNING: CPU: 9 PID: 2194 at mm/page_alloc.c:3931 __alloc_pages_slowpath+0x9db/0xec0
Call Trace:
? get_page_from_freelist+0x49d/0x11f0
? alloc_pages_current+0x6a/0xe0
? new_slab+0x499/0x690
__alloc_pages_nodemask+0x265/0x280
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x18/0x40
kmalloc_order_trace+0x24/0xb0
? acpi_ut_allocate_object_desc_dbg+0x62/0x10c
__kmalloc+0x203/0x220
acpi_os_allocate_zeroed+0x34/0x36
acpi_ut_copy_eobject_to_iobject+0x266/0x31e
acpi_evaluate_object+0x166/0x3b2
acpi_smbus_cmi_access+0x144/0x530 [i2c_scmi]
i2c_smbus_xfer+0xda/0x370
i2cdev_ioctl_smbus+0x1bd/0x270
i2cdev_ioctl+0xaa/0x250
do_vfs_ioctl+0xa4/0x600
SyS_ioctl+0x79/0x90
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
ACPI Error: Evaluating _SBW: 4 (20170831/smbus_cmi-185)
This problem occurs because the length of ACPI Buffer object is not
defined/initialized in the code before a corresponding ACPI method is
called. The obvious patch below fixes this issue.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Acked-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistake in dev_notice message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We shouldn't attempt to DMA map the message buffers passed into this
driver from the i2c core unless the message we're mapping have been
properly setup for DMA. The i2c core indicates such a situation by
setting the I2C_M_DMA_SAFE flag, so check for that flag before using DMA
mode. We can also bounce the buffer if it isn't already mapped properly
by using the i2c_get_dma_safe_msg_buf() APIs, so do that when we
want to use DMA for a message.
This fixes a problem where the kernel oopses cleaning pages for a buffer
that's mapped into the vmalloc space. The pages are returned from
request_firmware() and passed down directly to the i2c master to write
to the i2c touchscreen device. Mapping vmalloc buffers with
dma_map_single() won't work reliably, causing an oops like below:
Unable to handle kernel paging request at virtual address ffffffc01391d000
...
Reported-by: Philip Chen <philipchen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The function that computes clock parameters from divisors did not
respect the maximum size of the bitfields that the parameters were
written to. This fixes the bug.
This bug can be reproduced with (and this fix verified with) the test
at: https://kunit-review.googlesource.com/c/linux/+/1035/
Discovered-by-KUnit: https://kunit-review.googlesource.com/c/linux/+/1035/
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a better annotation, so GCC won't complain anymore:
drivers/i2c/busses/i2c-aspeed.c:458:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events
properly") moved interrupt acknowledgment to the end of the interrupt
handler. In part this was done because the AST2500 datasheet says:
I2CD10 Interrupt Status Register
bit 2 Receive Done Interrupt status
S/W needs to clear this status bit to allow next data receiving.
Acknowledging Receive Done before receive data was handled resulted in
receive errors on high speed I2C busses.
However, interrupt acknowledgment was not only moved to the end of the
interrupt handler for Receive Done Interrupt status, but for all interrupt
status bits. This could result in race conditions if a second interrupt was
received during interrupt handling and not handled but still acknowledged
at the end of the interrupt handler.
Acknowledge only "Receive Done Interrupt status" late in the interrupt
handler to solve the problem.
Fixes: 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events properly")
Cc: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In most of cases, interrupt bits are set one by one but there are
also a lot of other cases that Aspeed I2C IP sends multiple
interrupt bits with combining master and slave events using a
single interrupt call. It happens much more in multi-master
environment than single-master. For an example, when master is
waiting for a NORMAL_STOP interrupt in its MASTER_STOP state,
SLAVE_MATCH and RX_DONE interrupts could come along with the
NORMAL_STOP in case of an another master immediately sends data
just after acquiring the bus. In this case, the NORMAL_STOP
interrupt should be handled by master_irq and the SLAVE_MATCH and
RX_DONE interrupts should be handled by slave_irq. This commit
modifies irq hadling logic to handle the master/slave combined
events properly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA mode will always be used in i2c transactions, try to allocate
a DMA safe buffer if the buf of struct i2c_msg used is not DMA safe.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a3d411fb38 ("i2c: designware: Disable pm for PMIC i2c-bus even if
there is no _SEM method"), always set the pm_disabled flag on the I2C7
controller, even if its bus was not shared with the PUNIT.
This was a workaround for various suspend/resume issues, after the
following 2 commits this workaround is no longer necessary:
Commit 5415277283 ("PM: i2c-designware-platdrv: Suspend/resume at the
late/early stages")
Commit e6ce0ce34f ("ACPI / LPSS: Add device link for CHT SD card
dependency on I2C")
Therefor this commit removes this workaround.
After this commit the pm_disabled flag is only used to indicate that the
bus is shared with the PUNIT and after other recent changes we no longer
call dev_pm_syscore_device(dev, true), so we are no longer actually
disabling (non-runtime) pm, so this commit also renames the flag to
shared_with_punit to better reflect what it is for.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes: 84d7f2ebd7 ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Microsemi Ocelot I2C controller is a designware IP. It also has a
second set of registers to allow tweaking SDA hold time and spike
filtering.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[wsa: made one function static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because some old designware IPs were not supporting setting an SDA hold
time, vendors developed their own solution. Add a way for the final driver
to provide its own SDA hold time handling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the #ifdef CONFIG_OF section to the top of the file, after the ACPI
section so functions defined there can be used in dw_i2c_plat_probe.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to device_get_match_data in probe to match the device specific data
instead of using the acpi specific function.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
driver's compatible entry.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: dd6fd4a327 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We only freed the bounce buffer after successful DMA, missing the cases
where DMA setup may have gone wrong. Use a better location which always
gets called after each message and use 'stop_after_dma' as a flag for a
successful transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After various refactoring over the years, start_ch() doesn't return
errno anymore, so make the function return void. This saves the error
handling when calling it which in turn eases cleanup of resources of a
future patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
a) rename to 'put' instead of 'release' to match 'get' when obtaining
the buffer
b) change the argument order to have the buffer as first argument
c) add a new argument telling the function if the message was
transferred. This allows the function to be used also in cases
where setting up DMA failed, so the buffer needs to be freed without
syncing to the message buffer.
Also convert the only user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
PSAT |= 0x03
Local0 = PSAT /* \_SB_.I2C5.PSAT */
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
When doing a REP_START after a read message, the driver used to trigger
a STOP first which would then be overwritten by REP_START. This was the
only stable method found when doing the last refactoring. However, this
was not in accordance with the documentation.
After research from our BSP team and myself, we now can implement a
version which works and is according to the documentation. The new
approach ensures the ICMCR register is only changed when really needed.
Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N).
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use BIT macro to avoid shift-31-problem, indent a little more and use
GENMASK to make it easier to add new flags.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During ipmi stress tests we see occasional failure of transactions
at the boot time. This happens in the case of a I2C_M_RECV_LEN
transactions, when the read transfer completes (with the initial
read length of 34) before the driver gets a chance to handle interrupts.
The current driver code expects at least 2 interrupts for I2C_M_RECV_LEN
transactions. The length is updated during the first interrupt, and the
buffer contents are only copied during subsequent interrupts. In case of
just one interrupt, we will complete the transaction without copying
out the bytes from RX fifo.
Update the code to drain the RX fifo after the length update,
so that the transaction completes correctly in all cases.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value
and stretch the clock in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adjusts spinlock scope to make it wrap the whole irq
handler using a single lock/unlock which covers both master and
slave handlers.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are some log printing without a newline character. This
patch adds the missing newline characters.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver supports multiple hardware variants of Exynos I2C controller
which differ in FIFO depth, handling of interrupts and bus recovery in
HSI2C_MASTER_ST_LOSE state.
The difference in variant was a single bit set for Exynos7 variants and
implicit lack of this bit for other variants.
Make each variant explicit which also fixes the GCC warning about
documentation:
drivers/i2c/busses/i2c-exynos5.c:223: warning: Function parameter or member 'hw' not described in 'exynos_hsi2c_variant'
No change in functionality.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bus recovery should reset the bus with the standard i2c recovery
procedure. Populate the necessary fields so that the standard procedure
can perform the reset.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since there are many ports per master, each with it's own adapter and
chardev, we need some locking to prevent transfers from changing the
master state while other transfers are in progress.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Execute I2C transfers from the FSI-attached I2C master. Use polling
instead of interrupts as we have no hardware IRQ over FSI.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add abort procedure for failed transfers. Add engine reset procedure
that is executed during the abort to recover from various fault
conditions.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add and initialize I2C adapters for each port on the FSI-attached I2C
master. Ports for each master are defined in the devicetree.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To break out of recovery as early as possible, feed back the bus_free
logic state.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
The i2c_lock_adapter name is ambiguous since it is unclear if it
refers to the root adapter or the adapter you name in the argument.
The natural interpretation is the adapter you name in the argument,
but there are historical reasons for that not being the case; it
in fact locks the root adapter. Just remove the function and force
users to spell out the I2C_LOCK_ROOT_ADAPTER name to indicate what
is really going on. Also remove i2c_unlock_adapter, of course.
This patch was generated with
git grep -l 'i2c_\(un\)\?lock_adapter' \
| xargs sed -i 's/i2c_\(un\)\?lock_adapter(\([^)]*\))/'\
'i2c_\1lock_bus(\2, I2C_LOCK_ROOT_ADAPTER)/g'
followed by white-space touch-up.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d083 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678 was made we now disable 'packet
mode' before the delay from commit f70893d083 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Intel Ice Lake has the same SMBus host controller than Intel Cannon
Lake. Add the PCI ID to the drivers list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make list of supported chipsets a little bit shorter by consolidating
names that belong to the same family.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to support advanced features, the I2C FIFO interface was
changed in the version of the Tegra I2C controller found in Tegra194.
The changes are backwards incompatible, so the driver needs to be
programmed in a slightly different way on new chips.
Add support for MST FIFO programming and add an OF match entry for
Tegra194. At the same time, mark all prior generations of this
controller as not having the MST FIFO interface.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add another injector for an incomplete transfer. As mentioned in the
docs, this one is important to check bus recovery algorithms with it.
Otherwise random data may be sent to devices!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the incomplete_transfer routine reusable, so we can add other test
cases with different patterns later. Prepare the docs for that, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial added debug print for dev->clk_freq doesn't necessarily tell the
actual bus speed or mode the controller is operating. For instance it
may indicate 1 MHz Fast Mode Plus or 3.4 MHz High Speed but driver ends up
using 400 kHz Fast Mode due missing timing parameters or missing support
from HW.
Add a debug print that prints the bus speed based on the validated speed
that gets programmed into a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time is an important timing parameter and often reason for
arbitration lost errors if not set to a correct value. Add a debug print
for it in order to see what value gets programmed to a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mixed timing parameter validation, calculation and their debug prints
with HW initialization in i2c_dw_init_master() and i2c_dw_init_slave()
as been bothering me some time.
It makes function a little bit unclear to follow, doesn't show what steps
are needed to do only once during probe and what are needed whenever HW
needs to be reinitialized. Also those debug prints show information that
doesn't change runtime and thus are also needlessly printed multiple times
whenever HW is reinitialized.
Thus let the i2c_dw_init_master() and i2c_dw_init_slave() to do only HW
initialization and move out one time parameter setting and debug prints
to separate functions which are called only during probe.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time configuration is common to both master and slave code. It
is also something that can be done once during probe and do only
register write when HW needs to be reinitialized.
Remove duplication and move SDA hold time configuration to common code.
It will be called from slave probe and for master code from a new
i2c_dw_set_timings_master() to where we will populate more probe time
timing parameter setting.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is rather readability update than micro-optimization, or if not
optimization at all. We take the input clock rate to a variable and pass
that to SCL timing parameter calculation functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It looks ___constant_swab32 is an internal byte swap detail. Switch to
swap32() and include header file for it explicitly. Now it comes
implicitly via linux/i2c.h include.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move register access detection out from master and slave HW
initialization code to common code. Motivation for this is to have
register access configured before HW initialization and remove
duplicated code.
This allows to do further separation between probe time initialization
and runtime reinitialization code.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 43df43e6ba ("i2c: designware: Don't set SCL timings and speed
mode when in slave mode") made variable comp_param1 needless in
i2c_dw_init_slave(). Remove it now.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit f2a8aa053c ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code.
This has caused the power-supply registered by the fusb302 driver,
which determines how much current the bq24190 can draw, to change name
from "fusb302-typec-source" to "tcpm-source-psy-i2c-fusb302".
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that during the conversion from gpio* to gpiod*, the initial
state of SCL was wrongly switched to LOW. Fix it to be HIGH again.
Fixes: 7bb75029ef ("i2c: gpio: Enforce open drain through gpiolib")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
The added Centriq support broke compilation with CONFIG_ACPI disabled:
drivers/i2c/busses/i2c-qup.c: In function 'qup_i2c_probe':
drivers/i2c/busses/i2c-qup.c:1707:25: error: 'qup_i2c_acpi_match' undeclared (first use in this function); did you mean 'qup_i2c_recv_data'?
This fixes it by removing the extraneous #ifdef. All ACPI specific
code will be dropped implicitly when that option is disabled, but
the compiler first needs to see it.
Fixes: 902a91a02b ("i2c: qup: add probe path for Centriq ACPI devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Nothing prevents I2C clients to access I2C while Tegra's driver is being
suspended, this results in -EBUSY error returned to the clients and that
may have unfortunate consequences. In particular this causes problems
for the TPS6586x MFD driver which emits hundreds of "failed to read
interrupt status" error messages on resume from suspend. This happens if
TPS6586X is used to wake system from suspend by the expired RTC alarm
timer because TPS6586X is an I2C device driver and its IRQ handler reads
the status register while Tegra's I2C driver is suspended, i.e. just after
kernel enabled IRQ's during of resume-from-suspend process.
Note that the removed tegra_i2c_resume() invoked tegra_i2c_init() which
performs HW reset. That seems was also not entirely correct because moving
tegra_i2c_resume to an earlier stage of resume-from-suspend process causes
I2C transfer to fail in the case of TPS6586X. It is fine to remove the
HW-reinitialization for now because it should be only needed in a case of
using lowest power-mode during suspend, which upstream kernel doesn't
support.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because it looks neater.
For diolan, this allows factoring out some code that is now common
between if and else.
For eg20t, pch_i2c_writebytes is always called with a write in
msgs->flags, and pch_i2c_readbytes with a read.
For imx, i2c_imx_dma_write and i2c_imx_write are always called with a
write in msgs->flags, and i2c_imx_read with a read.
For qup, qup_i2c_write_tx_fifo_v1 is always called with a write in
qup->msg->flags.
For stu300, also restructure debug output for resends, since that
code as a result is only handling debug output.
Reviewed-by: Guenter Roeck <linux@roeck-us.net> [diolan]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [efm32 and imx]
Acked-by: Linus Walleij <linus.walleij@linaro.org> [stu300]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The URL is broken. This patch fixes it.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
[wsa: shortened the URL a bit]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a module parameter to override SCL frequency provided by firmware.
This can be useful when testing spec compliance for I2C modes or when
debugging issues across multiple operating frequencies.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C spec UM10204 Rev. 6 specifies the following timings.
Standard Fast Mode Fast Mode Plus
SCL low 4.7us 1.3us 0.5us
SCL high 4.0us 0.6us 0.26us
This results in a 33%/66% duty cycle as opposed to the 50%/50% duty cycle
used for Standard-mode.
Add High Time Divider settings to correct duty cycle for FM(400kHz) and
FM+(1MHz).
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Previously the QUP driver limited operation mode to I2C Fast Mode. Add
Fast Mode Plus functionality by raising SCL limit from 400kHz to 1MHz.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for Qualcomm Centriq devices that are qup-v2 compatible but
do not support DMA, so nodma needs to be set.
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In the for-loop test, ret will be either 0 or 1. So, the
comparison is pointless. Drop it, and drop the initializer
which is then also pointless.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Just use the value directly instead of assigning it to a
variable first. And then drop the unused variable.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now %p doesn't print visible pointer address unless the user
really want it. According to Documentation/core-api/printk-formats.rst,
%px should be used instead, otherwise we could see:
rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at (____ptrval____)
But I don't really understand why we need dump it in the first place!
Let's remove the whole pointless log.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()") and b7f6258402 ("i2c: add quirk checks to core"), the
I2C core does this check now. We can remove it here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>
The driver will not probe unless bq24190 is loaded, so
making it a dependency.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SMBus transactions the max permissible transfer size is
I2C_SMBUS_BLOCK_SIZE. It is possible that some clients might
not follow it strictly occasionally.
This would lead to stack corruption if the driver copies more than
I2C_SMBUS_BLOCK_SIZE bytes. Add a check to avoid such conditions.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hardware does not handle updates to the length register gracefully
if the new value is less than the number of bytes received so far. If
this happens, the i2c controller will not stop the receive transaction
properly.
Fix this by ensuring that the updated length is ok. This is done by
making sure that the new length written to hardware is at least few
bytes more than the bytes received so far.
While at that refactor the length updation to a new function.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for SMBus alert mechanism to i2c-xlp9xx driver.
The second interrupt is parsed to use for SMBus alert.
The first interrupt is the i2c controller main interrupt.
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are no platform_data users anymore. Move the structs into the
driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Some data structure members were either misspelled or missing.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Fixes: 380b8a85e7 ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With CONFIG_PM, we get a harmless build warning:
drivers/i2c/busses/i2c-i801.c:1723:12: warning: ‘i801_resume’ defined but not used [-Wunused-function]
static int i801_resume(struct device *dev)
^~~~~~~~~~~
drivers/i2c/busses/i2c-i801.c:1714:12: warning: ‘i801_suspend’ defined but not used [-Wunused-function]
static int i801_suspend(struct device *dev)
^~~~~~~~~~~~
Follow design pattern from other drivers like i2c-brcmstb, i2c-mpc,
i2c-ocores, i2c-pnx, i2c-puv3, i2c-st, i2c-stu300 and i2c-mux-pca954x
and changing the ifdef CONFIG_PM to CONFIG_PM_SLEEP.
Fixes: a9c8088c79 ("i2c: i801: Don't restore config registers on runtime PM")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistakes in dev_dbg messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a difference between attempts and retries.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The else branch cannot be taken as i will always equal num.
Get rid of the whole construct.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
exynos5_i2c_xfer contains lots of dead code, let's remove it and simplify
the rest. The patch should not introduce functional changes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Suggested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Low-level controller enable function __i2c_dw_enable is overloaded to
also handle disabling. What's worse, even though the documentation
requires polling the IC_ENABLE_STATUS register when disabling, this
is not done: polling needs to be requested specifically by calling
__i2c_dw_enable_and_wait, which can also poll on enabling, but that
doesn't work if the IC_ENABLE_STATUS register is not implemented.
This is quite confusing if not in fact backwards.
Especially since the documentation says that disabling should be
followed by polling, the driver should be using a separate function
where it does one-shot disables to make the optimization stand out.
This refactors the two functions so that requested status is given
in the name rather than in a boolean argument. Specifically:
- __i2c_dw_enable: enable without polling (in accordance with docs)
- __i2c_dw_disable: disable and do poll (also as suggested by docs)
- __i2c_dw_disable_nowait: disable without polling (Linux-specific)
No functional change.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: fixed blank lines in header file]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 174a13aa86 ("i2c: Add viperboard i2c master driver")
Returning -1 (-EPERM) is not appropriate here, go with -EIO.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7 ("i2c: New PMC MSP71xx TWI bus driver")
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b144df1d7 ("i2c: New PMC MSP71xx TWI bus driver")
Not all revisions of DW I2C controller implement the enable status register.
On platforms where that's the case (e.g. BG2CD and SPEAr ARM SoCs), waiting
for enable will time out as reading the unimplemented register yields zero.
It was observed that reading the IC_ENABLE_STATUS register once suffices to
avoid getting it stuck on Bay Trail hardware, so replace polling with one
dummy read of the register.
Fixes: fba4adbbf6 ("i2c: designware: must wait for enable")
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Tested-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
These days, the I2C core ensures that the embedded adapter device
ignores the PM states of its children already. Because the adapter
device is an opaque logical device, there is no need for drivers to
repeat that again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
axxia_i2c_init() uses clk_get_rate() for idev->i2c_clk. clk_get_rate()
should only be called if the clock is enabled, so ensure that by moving
the clk_prepare_enable() call before the call to axxia_i2c_init().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 08678b850c ("i2c: axxia: Add I2C driver for AXM55xx")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Give a clear testcase for people wishing to change this code. It is also
a reminder for me if people ask about it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It allows mlxcpld driver to be connected to pre-defined adapter number
equal or greater than one, in order to avoid current limitation, assuming
usage of id number one only.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It fixes report about supported functionality.
Functionality can be different up to CPLD capability.
Fixes: 6bec23bff9 (i2c: mlxcpld: add master driver for mellanox systems)
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for smbus block read transaction. CPLD smbus block read bit
of capability register is verified during driver initialization, and driver
data is updated if such capability is available. In case an upper layer
requests a read transaction of length one and expects that length will be
the first received byte, driver will notify CPLD about SMBus block read
transaction flavor, so CPLD will know to execute such kind of transaction.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It adds support for extended length of read and write transactions.
New CPLD logic allows double size of the read and write transactions
length. This feature is verified through capability register, which is
renamed from unclear LPF_REG to CPBLTY_REG. Two bits 5 and 6 of these
register are used for length capability detection, while only 01
combination indicates support of extended transaction length.
Others mean lack of such support.
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call mtk_i2c_probe() is to match an entry in
mtk_i2c_of_match[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Restoring configuration registers is only needed when we hand control
to the firmware. This is never the case with runtime power
management. The device will autosuspend whenever not used, so avoid
useless register writes by defining suspend/resume only, and not
runtime_suspend/runtime_resume.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With FIFO enabled it is possible to read multiple bytes
at once in the interrupt handler as long as RXRDY is
set. This may also reduce the number of interrupts.
This patch polls RXRDY and reads all available bytes at
once.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wsa: reformatted comment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds a generic DMA API to implement DMA support for i2c-stm32fx
drivers
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds slave support for I2C controller embedded in STM32F7 SoC
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for 10-bit device address for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We found the I2C controller count register is unreliable sometimes,
that will cause I2C to lose data. Thus we can read the data count
from 'i2c_dev->count' instead of the I2C controller count register.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add one flag to indicate if the i2c controller has been in suspend state,
which can prevent i2c accesses after i2c controller is suspended following
system suspend.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 22e94bd677 ("i2c: i801: store and restore the SLVCMD register at load and unload")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org # v4.10+
Pull i2c updates from Wolfram Sang:
-I2C core now reports proper OF style module alias. I'd like to repeat
the note from the commit msg here (Thanks, Javier!):
NOTE: This patch may break out-of-tree drivers that were relying
on this behavior, and only had an I2C device ID table even
when the device was registered via OF.
There are no remaining drivers in mainline that do this, but
out-of-tree drivers have to be fixed and define a proper OF
device ID table to have module auto-loading working.
- new driver for the SynQuacer I2C controller
- major refactoring of the QUP driver
- the piix4 driver now uses request_muxed_region which should fix a
long standing resource conflict with the sp5100_tco watchdog
- a bunch of small core & driver improvements
* 'i2c/for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: add support for Socionext SynQuacer I2C controller
dt-bindings: i2c: add binding for Socionext SynQuacer I2C
i2c: Update i2c_trace_msg static key to modern api
i2c: fix parameter of trace_i2c_result
i2c: imx: avoid taking clk_prepare mutex in PM callbacks
i2c: imx: use clk notifier for rate changes
i2c: make i2c_check_addr_validity() static
i2c: rcar: fix mask value of prohibited bit
dt-bindings: i2c: document R8A77965 bindings
i2c: pca-platform: drop gpio from platform data
i2c: pca-platform: use device_property_read_u32
i2c: pca-platform: unconditionally use devm_gpiod_get_optional
sh: sh7785lcr: add GPIO lookup table for i2c controller reset
i2c: qup: reorganization of driver code to remove polling for qup v2
i2c: qup: reorganization of driver code to remove polling for qup v1
i2c: qup: send NACK for last read sub transfers
i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
i2c: qup: change completion timeout according to transfer length
i2c: qup: use the complete transfer length to choose DMA mode
i2c: qup: proper error handling for i2c error in BAM mode
...
This is a cleaned up version of the I2C controller driver for
the Fujitsu F_I2C IP, which was never supported upstream, and
has now been incorporated into the Socionext SynQuacer SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[wsa: updated MAINTAINERS entry and removed two empty lines]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fabrizio Castro