Final drm-misc feature pull for 4.15:
UAPI Changes:
- new madvise ioctl for vc4 (Boris)
Core Changes:
- plane commit tracking fixes (Maarten)
- vgaarb improvements for fancy new platforms (aka ppc64 and arm64) by
Bjorn Helgaas
Driver Changes:
- pile of new panel drivers: Toshiba LT089AC19000, Innolux AT043TN24
- more sun4i work to support A10/A20 Tcon and hdmi outputs
- vc4: fix sleep in irq handler by making it threaded (Eric)
- udl probe/edid read fixes (Robert Tarasov)
And a bunch of misc small cleanups/refactors and doc fixes all over.
* tag 'drm-misc-next-2017-10-20' of git://anongit.freedesktop.org/drm/drm-misc: (32 commits)
drm/vc4: Fix sleeps during the IRQ handler for DSI transactions.
drm/vc4: Add the DRM_IOCTL_VC4_GEM_MADVISE ioctl
drm/panel: simple: add Toshiba LT089AC19000
dma-fence: remove duplicate word in comment
drm/panel: simple: add delays for Innolux AT043TN24
drm/panel: simple: add bus flags for Innolux AT043TN24
drm/panel: simple: fix vertical timings for Innolux AT043TN24
drm/atomic-helper: check that drivers call drm_crtc_vblank_off
drm: some KMS todo ideas
vgaarb: Factor out EFI and fallback default device selection
vgaarb: Select a default VGA device even if there's no legacy VGA
drm/bridge: adv7511: Fix a use after free
drm/sun4i: Add support for A20 display pipeline components
drm/sun4i: Add support for A10 display pipeline components
drm/sun4i: hdmi: Support HDMI controller on A10
drm/sun4i: tcon: Add support for A10 TCON
drm/sun4i: backend: Support output muxing
drm/sun4i: tcon: Move out the tcon0 common setup
drm/sun4i: tcon: Don't rely on encoders to set the TCON mode
drm/sun4i: tcon: Don't rely on encoders to enable the TCON
...
This contains a bit of cleanup and some minor fixes for the host1x and
Tegra DRM drivers. There's also some more preparatory work for Tegra186
support which I'm not quite ready to send upstream because the GPIO
driver needed for HDMI support has been stuck for months, and we can't
do much without it. Hopefully that driver will land in v4.15, which
would mean we could go ahead with Tegra186 display support in v4.16.
-----BEGIN PGP SIGNATURE-----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=nsc7
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.15-rc1
This contains a bit of cleanup and some minor fixes for the host1x and
Tegra DRM drivers. There's also some more preparatory work for Tegra186
support which I'm not quite ready to send upstream because the GPIO
driver needed for HDMI support has been stuck for months, and we can't
do much without it. Hopefully that driver will land in v4.15, which
would mean we could go ahead with Tegra186 display support in v4.16.
* tag 'drm/tegra/for-4.15-rc1' of git://anongit.freedesktop.org/tegra/linux: (21 commits)
drm/tegra: hdmi: Add cec-notifier support
drm/tegra: dc: Perform a complete reset sequence
drm/tegra: dc: Make sure to set the module clock rate
drm/tegra: dc: Simplify atomic plane helper functions
drm/tegra: dc: Move some declarations to dc.h
drm/tegra: vic: Use of_device_get_match_data()
drm/tegra: sor: Use of_device_get_match_data()
drm/tegra: hdmi: Use of_device_get_match_data()
drm/tegra: dc: Use of_device_get_match_data()
drm/tegra: Use u64_to_user_ptr helper
gpu: host1x: Fix incorrect comment for channel_request
gpu: host1x: Disassemble more instructions
gpu: host1x: Improve debug disassembly formatting
gpu: host1x: Enable gather filter
gpu: host1x: Enable Tegra186 syncpoint protection
gpu: host1x: Call of_dma_configure() after setting bus
drm/tegra: Add Tegra186 support for VIC
gpu: host1x: Add Tegra186 support
dt-bindings: host1x: Add Tegra186 information
gpu: host1x: syncpt: Request syncpoints per client
...
These provide crtc-id based functions instead of pipe-number, while
also offering higher resolution time (ns) and wider frame count (64)
as required by the Vulkan API.
v2:
* Check for DRIVER_MODESET in new crtc-based vblank ioctls
Failing to check this will oops the driver.
* Ensure vblank interupt is running in crtc_get_sequence ioctl
The sequence and timing values are not correct while the
interrupt is off, so make sure it's running before asking for
them.
* Short-circuit get_sequence if the counter is enabled and accurate
Steal the idea from the code in wait_vblank to avoid the
expense of drm_vblank_get/put
* Return active state of crtc in crtc_get_sequence ioctl
Might be useful for applications that aren't in charge of
modesetting?
* Use drm_crtc_vblank_get/put in new crtc-based vblank sequence ioctls
Daniel Vetter prefers these over the old drm_vblank_put/get
APIs.
* Return s64 ns instead of u64 in new sequence event
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
v3:
* Removed FIRST_PIXEL_OUT_FLAG
* Document that the timestamp in the query and event are
that of the first pixel leaving the display engine for
the display (using the same wording as the Vulkan spec).
Suggested-by: Michel Dänzer <michel@daenzer.net>
Acked-by: Dave Airlie <airlied@redhat.com>
[airlied: left->leaves (Michel)]
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The feature implementation isn't stable yet. Reject any attempt to use
the IOCTLs for now. This keeps most of the code in place, so we can stabilize
it in-tree, but keeps userspace from using the feature for now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
The performance monitoring feature isn't stable enough yet, so don't advertise
it to userspace yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Place drm_event_vblank in a new union that includes that and a bare
drm_event structure. This will allow new members of that union to be
added in the future without changing code related to the existing vbl
event type.
Assignments to the crtc_id field are now done when the event is
allocated, rather than when delievered. This way, delivery doesn't
need to have the crtc ID available.
v2:
* Remove 'dev' argument from create_vblank_event
It wasn't being used anyways, and if we need it in the future,
we can always get it from crtc->dev.
* Check for MODESETTING before looking for crtc in queue_vblank_event
UMS drivers will oops if we try to get a crtc, so make sure
we're modesetting before we try to find a crtc_id to fill into
the event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit dc695b85fde88eca3ef3b03fcd82f15b6bc6e462)
This modifies the datatypes used by the vblank code to provide 64 bits
of vblank count.
The driver interfaces have been left using 32 bits of vblank count;
all of the code necessary to widen that value for the user API was
already included to handle devices returning fewer than 32-bits.
This will provide the necessary datatypes for the Vulkan API.
v2:
* Re-write wait_vblank ioctl to ABSOLUTE sequence
When an application uses the WAIT_VBLANK ioctl with RELATIVE
or NEXTONMISS bits set, the target vblank interval is updated
within the kernel. We need to write that target back to the
ioctl buffer and update the flags bits so that if the wait is
interrupted by a signal, when it is re-started, it will target
precisely the same vblank count as before.
* Leave driver API with 32-bit vblank count
v3:
* Rebase on top of Arnd Bergmann's patch which had
the switch to ktime_t parts.
[airlied: fix conflict with Ville vblank change].
Suggested-by: Michel Dänzer <michel@daenzer.net>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 2affbc16983e4fc90960bc7f70e7615f4228199b)
In order to support CEC the HDMI driver has to inform the CEC driver
whenever the physical address changes. So when the EDID is read the
CEC driver has to be informed and whenever the hotplug detect goes
away.
This is done through the cec-notifier framework.
The link between the HDMI driver and the CEC driver is done through
the hdmi-phandle property in the tegra-cec node in the device tree.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order for the reset to be applied properly, the module clock must be
enabled during the assertion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When applying the PLL changes from the computed state object, make sure
to set the rate of the display controller module clock. Failing to do so
can yield to a situation where the parent will be set to the proper
pixel clock, but the module clock will be divided down to the rate that
is happened to be set to before the parent rate change.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the tegra_dc_disable_window() function whose only purpose was to
allow tegra_plane_atomic_update() to also call it. Fix that by shuffling
tegra_plano_atomic_disable() to before tegra_plane_atomic_update().
While at it, also remove the overlay plane helper functions because they
are exactly the same as the primary plane helper functions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the u64_to_user_ptr helper macro to cast IOCTL argument u64 values
to user pointers instead of writing out the cast manually. Also do
some other cleanup with user pointers to make them stand out more
and look cleaner.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function actually doesn't sleep in the version that was merged.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The disassembler for debug dumps was missing some newer host1x opcodes.
Add disassembly support for these.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x driver prints out "disassembly" dumps of the command FIFO
and gather contents on submission timeouts. However, the output has
been quite difficult to read with unnecessary newlines and occasional
missing parentheses.
Fix these problems by using pr_cont to remove unnecessary newlines
and by fixing other small issues.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gather filter is a feature present on Tegra124 and newer where the
hardware prevents GATHERed command buffers from executing commands
normally reserved for the CDMA pushbuffer which is maintained by the
kernel driver.
This commit enables the gather filter on all supporting hardware.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since Tegra186 the Host1x hardware allows syncpoints to be assigned to
specific channels, preventing any other channels from incrementing
them.
Enable this feature where available and assign syncpoints to channels
when submitting a job. Syncpoints are currently never unassigned from
channels since that would require extra work and is unnecessary with
the current channel allocation model.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
of_dma_configure() now checks the device's bus before configuring it, so
we need to set the device's bus before calling.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Tegra186 support for VIC - no changes are required except for new
firmware and compatibility string.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the implementation of Host1x present on the Tegra186.
The register space has been shuffled around a little bit, requiring
addition of some chip-specific code sections. Tegra186 also adds
several new features, most importantly the hypervisor, but those are
not yet supported with this commit.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the Tegra186-specific hypervisor-related register range
properties.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than request syncpoints for a struct device *, request them for a
struct host1x_client *. This is important because subsequent patches are
going to break the assumption that host1x will always be the parent for
devices requesting a syncpoint. It's also a more natural choice because
host1x clients are really the only ones that will know how to deal with
syncpoints.
Note that host1x clients are always guaranteed to be children of host1x,
regardless of their location in the device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Avoid some boilerplate by calling of_device_get_match_data() instead of
open-coding the equivalent in the driver.
While at it, shuffle around some code to avoid unnecessary local
variables.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is the amdkfd pull request for 4.15 merge window.
The patches here are relevant only for Kaveri and Carrizo. Still no dGPU patches.
The main goal is to continue alignment with the internal AMD development tree.
The following is a summary of the changes:
- Improvements and fixes to suspend/resume code
- Improvements and fixes to process termination code
- Cleanups in the queue unmapping functionality
- Reuse code from amdgpu
* tag 'drm-amdkfd-next-2017-10-18' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Improve multiple SDMA queues support per process
drm/amdkfd: Limit queue number per process and device to 127
drm/amdkfd: Clean up process queue management
drm/amdkfd: Compress unnecessary function parameters
drm/amdkfd: Improve process termination handling
drm/amdkfd: Avoid submitting an unnecessary packet to HWS
drm/amdkfd: Fix MQD updates
drm/amdkfd: Pass filter params to unmap_queues_cpsch
drm/amdkfd: move locking outside of unmap_queues_cpsch
drm/amdkfd: Avoid name confusion involved in queue unmapping
drm/amdkfd: Drop _nocpsch suffix from shared functions
drm/amdkfd: Reuse CHIP_* from amdgpu v2
drm/amdkfd: Use VMID bitmap from KGD v2
drm/amdkfd: Adjust dequeue latencies and timeouts
drm/amdkfd: Rectify the jiffies calculation error with milliseconds v2
drm/amdkfd: Fix suspend/resume issue on Carrizo v2
drm/amdkfd: Reorganize kfd resume code
Last batch of drm/i915 features for v4.15:
- transparent huge pages support (Matthew)
- uapi: I915_PARAM_HAS_SCHEDULER into a capability bitmask (Chris)
- execlists: preemption (Chris)
- scheduler: user defined priorities (Chris)
- execlists optimization (Michał)
- plenty of display fixes (Imre)
- has_ipc fix (Rodrigo)
- platform features definition refactoring (Rodrigo)
- legacy cursor update fix (Maarten)
- fix vblank waits for cursor updates (Maarten)
- reprogram dmc firmware on resume, dmc state fix (Imre)
- remove use_mmio_flip module parameter (Maarten)
- wa fixes (Oscar)
- huc/guc firmware refacoring (Sagar, Michal)
- push encoder specific code to encoder hooks (Jani)
- DP MST fixes (Dhinakaran)
- eDP power sequencing fixes (Manasi)
- selftest updates (Chris, Matthew)
- mmu notifier cpu hotplug deadlock fix (Daniel)
- more VBT parser refactoring (Jani)
- max pipe refactoring (Mika Kahola)
- rc6/rps refactoring and separation (Sagar)
- userptr lockdep fix (Chris)
- tracepoint fixes and defunct tracepoint removal (Chris)
- use rcu instead of abusing stop_machine (Daniel)
- plenty of other fixes all around (Everyone)
* tag 'drm-intel-next-2017-10-12' of git://anongit.freedesktop.org/drm/drm-intel: (145 commits)
drm/i915: Update DRIVER_DATE to 20171012
drm/i915: Simplify intel_sanitize_enable_ppgtt
drm/i915/userptr: Drop struct_mutex before cleanup
drm/i915/dp: limit sink rates based on rate
drm/i915/dp: centralize max source rate conditions more
drm/i915: Allow PCH platforms fall back to BIOS LVDS mode
drm/i915: Reuse normal state readout for LVDS/DVO fixed mode
drm/i915: Use rcu instead of stop_machine in set_wedged
drm/i915: Introduce separate status variable for RC6 and LLC ring frequency setup
drm/i915: Create generic functions to control RC6, RPS
drm/i915: Create generic function to setup LLC ring frequency table
drm/i915: Rename intel_enable_rc6 to intel_rc6_enabled
drm/i915: Name structure in dev_priv that contains RPS/RC6 state as "gt_pm"
drm/i915: Move rps.hw_lock to dev_priv and s/hw_lock/pcu_lock
drm/i915: Name i915_runtime_pm structure in dev_priv as "runtime_pm"
drm/i915: Separate RPS and RC6 handling for CHV
drm/i915: Separate RPS and RC6 handling for VLV
drm/i915: Separate RPS and RC6 handling for BDW
drm/i915: Remove superfluous IS_BDW checks and non-BDW changes from gen8_enable_rps
drm/i915: Separate RPS and RC6 handling for gen6+
...
Last set of features for 4.15. Highlights:
- Add a bo flag to allow buffers to opt out of implicit sync
- Add ctx priority setting interface
- Lots more powerplay cleanups
- Start to plumb through vram lost infrastructure for gpu reset
- ttm support for huge pages
- misc cleanups and bug fixes
* 'drm-next-4.15' of git://people.freedesktop.org/~agd5f/linux: (73 commits)
drm/amd/powerplay: Place the constant on the right side of the test
drm/amd/powerplay: Remove useless variable
drm/amd/powerplay: Don't cast kzalloc() return value
drm/amdgpu: allow GTT overcommit during bind
drm/amdgpu: linear validate first then bind to GART
drm/amd/pp: Fix overflow when setup decf/pix/disp dpm table.
drm/amd/pp: thermal control not enabled on vega10.
drm/amdgpu: busywait KIQ register accessing (v4)
drm/amdgpu: report more amdgpu_fence_info
drm/amdgpu:don't check soft_reset for sriov
drm/amdgpu:fix duplicated setting job's vram_lost
drm/amdgpu:reduce wb to 512 slot
drm/amdgpu: fix regresstion on SR-IOV gpu reset failed
drm/amd/powerplay: Tidy up cz_dpm_powerup_vce()
drm/amd/powerplay: Tidy up cz_dpm_powerdown_vce()
drm/amd/powerplay: Tidy up cz_dpm_update_vce_dpm()
drm/amd/powerplay: Tidy up cz_dpm_update_uvd_dpm()
drm/amd/powerplay: Tidy up cz_dpm_powerup_uvd()
drm/amd/powerplay: Tidy up cz_dpm_powerdown_uvd()
drm/amd/powerplay: Tidy up cz_start_dpm()
...
VC4's DSI1 has a bug where the AXI connection is broken for 32-bit
writes from the CPU, so we use the DMA engine to DMA 32-bit values
into registers instead. That sleeps, so we can't do it from the top
half.
As a solution, use an interrupt thread so that all our writes happen
when sleeping is is allowed.
v2: Use IRQF_ONESHOT (suggested by Boris)
v3: Style nitpicks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171014001255.32005-1-eric@anholt.net
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> (v2)
Move the constant on the right side of the comparison in order to
make the code easier to read.
Issue found by checkpatch script:
* WARNING: Comparisons should place the constant on the right side of
the test
Signed-off-by: Georgiana Chelu <georgiana.chelu93@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The result variable is initialized at the beginning of the function, but
its value does not change during the function execution. Thus, remove the
variable and return the SUCCESS value, which is 0.
Issue found by coccinelle script:
* Unneeded variable: "result". Return "0"
Path to the cocci script: scripts/coccinelle/misc/returnvar.cocci
Signed-off-by: Georgiana Chelu <georgiana.chelu93@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The kzalloc function returns a void pointer and the assignment
operator converts it to the type of pointer it is assigned to.
Therefore, there is no need to cast.
Issue found by alloc_cast.cocci:
* WARNING: casting value returned by memory allocation function
to <struct type> is useless.
Path to the cocci script: scripts/coccinelle/api/alloc/alloc_cast.cocci
Signed-off-by: Georgiana Chelu <georgiana.chelu93@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While binding BOs to GART we need to allow a bit overcommit in the GTT
domain. Otherwise we can never use the full GART space when GART size=GTT size.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For VM emulation for old UVD/VCE we need to validate the BO with linear
VRAM flag set first and then eventually bind it to GART.
Validating with linear VRAM flag set can move the BO to GART making
UVD/VCE read/write from an unbound GART BO.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clear the count in the single table setup function to
avoid missing any tables.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
regression issue.
caused by "f12f9f5e5d455edebc01"
forget to set start_thermal_controller function point.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Register accessing is performed when IRQ is disabled. Never sleep in
this function.
Known issue: dead sleep in many use cases of index/data registers.
v2:
- wrap polling fence functions.
- don't trigger IRQ for polling in case of wrongly fence signal.
v3:
- handle wrap round gracefully.
- add comments for polling function
v4:
- don't return negative timeout confused with error code
Signed-off-by: pding <Pixel.Ding@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only for GFX ring. This can help checking MCBP feature.
The fence at the end of the frame will indicate the completion status.
If the frame completed normally, the fence is written to the address
given in the EVENT_WRITE_EOP packet. If preemption occurred in the
previous IB the address is adjusted by 2 DWs. If work submitted in the
frame was reset before completion, the fence address is adjusted by
four DWs. In the case that preemption occurred, and before preemption
completed a reset was initiated, the address will be adjusted with six
DWs
Signed-off-by: pding <Pixel.Ding@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
with current WB usage we only use 57 slots, so 512
is extreamly sufficient, and reduce to 512 can
make WB fit into one page.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fw ucode is corrupted after vf flr by PSP so ucode_init() is
a must in psp_hw_init othewise KIQ/KCQ enabling will fail
Revert "drm/amdgpu: refine code delete duplicated error handling"
This reverts commit e57b87ff828f95efe992468e6d18c2c059b27aa9.
Revert "drm/amdgpu: move amdgpu_ucode_init_bo to amdgpu_device.c"
This reverts commit 815b8f8595148d06a64d2ce4282e8e80dfcb02f1.
Reviewed-by: Monk Liu <monk.liu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use PP_CAP macro.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use PP_CAP macro.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use PP_CAP and tidy up indentation.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use PP_CAP and tidy up indentation.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>