Releasing the touchscreen lets the internal statemachine left in a wrong state.
Due to this the release coordinate will be reported again by accident when the next
touchscreen event happens. This change sets up the correct state when waiting
for the next touchscreen event.
This has led to reported issues with calibrating the touchscreen.
Bug was introduced somewhere in the series that began with
18da755de5
Staging/iio/adc/touchscreen/MXS: add proper clock handling
in which the way this driver worked was substantially changed
to be interrupt driven rather than relying on a busy loop.
This was a regression in the 3.13 kernel.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both libertas USB driver and mwifiex_usb driver are registerring
with name 'usb8xxx'. The following conflict happens while trying
to load both drivers.
[6.211307] Error: Driver 'usb8xxx' is already registered...
[6.217261] mwifiex_usb: Driver register failed!
Fix it by renaming mwifiex_usb driver's name.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr(). Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:
device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.
Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Pull s390 bug fixes from Martin Schwidefsky:
"A couple of s390 bug fixes. The PCI segment boundary issue is a nasty
one as it can lead to data corruption"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: Fix missing subchannels after CHPID configure on
s390/pci/dma: use correct segment boundary size
s390/compat: fix sys_sched_getattr compat wrapper
s390/zcrypt: additional check to avoid overflow in msg-type 6 requests
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
This bug introduced in v3.14-rc1 breaks various devices on the Lager and
Kolesh shmobile boards and should thus be considered as a regression for
which a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The lb, qspi, sdh, sd0 and sd1 clocks have the PLL1 (divided by 2) as
their parent, not the main clock. Fix it.
This bug introduced in v3.14-rc1 breaks various devices on the Lager and
Kolesh shmobile boards and should thus be considered as a regression for
which a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Mostly unexciting driver fixes, plus one fix to lower the severity of
the log message when we don't use an optional regulator - the fixes for
ACPI system made this come up more often and it was correctly observed
that it was causing undue concern for users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yvBG
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Mostly unexciting driver fixes, plus one fix to lower the severity of
the log message when we don't use an optional regulator - the fixes
for ACPI system made this come up more often and it was correctly
observed that it was causing undue concern for users"
* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max14577: Fix invalid return value on DT parse success
regulator: core: Change dummy supplies error message to a warning
regulator: s5m8767: Add missing of_node_put
regulator: s5m8767: Use of_get_child_by_name
regulator: da9063: Bug fix when setting max voltage on LDOs 5-11
Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the three missing DIF related sense codes within
transport_generic_request_failure(), which are required to ensure
that the correct ASC/ASQC is generated by the subsequent call to
transport_send_check_condition_and_sense().
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.
This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.
CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) In current implementation, ecclayout->oobfree->offset is calculated with
respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
be stored contiguously in OOB.
So, this patch calculates ecclayout->oobfree->offset with respect to last
ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.
2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
which should not be over-written by any file-system metadata.
So this patch aligns oobfree->offset taking into account of such markers.
CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull irq fixes from Thomas Gleixner:
"Another four fixlets to tame the ARM orion irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: orion: Fix getting generic chip pointer.
irqchip: orion: clear stale interrupts in irq_startup
irqchip: orion: use handle_edge_irq on bridge irqs
irqchip: orion: clear bridge cause register on init
Here are a number of USB fixes for reported issues for 3.14-rc4
The majority of these are for USB gadget, phy, and musb driver issues.
And there's a few new device ids thrown in for good measure.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLmIACgkQMUfUDdst+ylvXQCdGw8XA8m783daSRWNhjtSCZdP
oq8An1mSq7W4Tj82EO91ulB5C9Q7+W4c
=BixM
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for reported issues for 3.14-rc4
The majority of these are for USB gadget, phy, and musb driver issues.
And there's a few new device ids thrown in for good measure"
* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: need to mask when writting endptflush and endptprime
usb: musb: correct use of schedule_delayed_work()
usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
usb: gadget: fix NULL pointer dereference
usb: gadget: printer: using gadget_is_otg to check otg support at runtime
phy: let phy_provider_register be the last step in registering PHY
phy-core: Don't allow building phy-core as a module
phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
phy-core: phy_get: Leave error logging to the caller
phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
usb: musb: correct use of schedule_delayed_work()
usb: musb: do not sleep in atomic context
USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
USB: EHCI: add delay during suspend to prevent erroneous wakeups
usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
usb: musb: do not sleep in atomic context
usb: gadget: s3c2410_udc: Fix build error
usb: musb: core: Fix remote-wakeup resume
usb: musb: host: Fix SuperSpeed hub enumeration
usb: musb: fix obex in g_nokia.ko causing kernel panic
Here is a single commit, a revert of a sysfs file change that ended up
breaking a userspace tool.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLK0ACgkQMUfUDdst+ynREQCcCl2HBK30ux8vwP0+tLvyx3AJ
lQYAn1COffBg1KS22gYyhm0Yez2pUgN2
=ZmpJ
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY revert from Greg KH:
"Here is a single commit, a revert of a sysfs file change that ended up
breaking a userspace tool"
* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: Set correct tty name in 'active' sysfs attribute"
Here is a single android driver fix for 3.14-rc4 that fixes a reported
problem in the binder driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLckACgkQMUfUDdst+ynaDwCfVtgwCfLL//Ck5rsI+dPcNoH4
A4IAnjukxtAABpGDXAezROVpPSvnchRZ
=zWji
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fix from Greg KH:
"Here is a single android driver fix for 3.14-rc4 that fixes a reported
problem in the binder driver"
* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: binder: Fix death notifications
Here is a single commit, to fix a reported problem in the mei driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlMJLO4ACgkQMUfUDdst+ylvewCgofUZto3Z7tZbbMD/yUn87zWK
wH8An2aPuyRWy5rLdbW3vw2gFBz9TXaJ
=2xyg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fix from Greg KH:
"Here is a single commit, to fix a reported problem in the mei driver"
* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: set client's read_cb to NULL when flow control fails
This reverts commit d8a5dc3033.
This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect. Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes bug introduced in 667a6b7a (regulator: max14577: Add missing
of_node_put). The DTS parsing function returned number of matched
regulators as success status which then was compared against 0 in probe.
Result was a probe fail after successful parsing the DTS:
max14577-regulator: probe of max14577-regulator failed with error 2
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviwed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=r7Cd
-----END PGP SIGNATURE-----
Merge tag 'irqchip-mvebu-fixes-3.14' of git://git.infradead.org/linux-mvebu into irq/urgent
irqchip mvebu fixes for v3.14
- orion:
- fixes for clearing bridge cause register, and clearing stale interrupts
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of of_device_ids,
but it more than one entry will match, then the device driver may choose
the wrong one. Commit 105353145e, "match each node compatible against
all given matches first", was queued for v3.14 but ended up causing
other bugs. Commit 06b29e76a7 attempted to fix it but it had other bugs.
Merely reverting the fix and waiting until v3.15 isn't a good option
because there is code in v3.14 that depends on the revised behaviour to
boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also adds
new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc pull,
but moving the test case data out of out of arch/arm so that it could be
validated on other architectures was important.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wJz0
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
Pull watchdog fix from Wim Van Sebroeck:
"It corrects the error code when no device was found for w83697hf_wdt"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: w83697hf_wdt: return ENODEV if no device was found
Enabling SPARSE_IRQ shows up a bug in the irq-orion bridge interrupt
handler. The bridge interrupt is implemented using a single generic
chip. Thus the parameter passed to irq_get_domain_generic_chip()
should always be zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Fixes: 9dbd90f17e ("irqchip: Add support for Marvell Orion SoCs")
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change (008fa749e0) that moved the
node release code to a separate function broke death notifications in
some cases. When it encountered a reference without a death
notification request, it would skip looking at the remaining
references, and therefore fail to send death notifications for them.
Cc: Colin Cross <ccross@android.com>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most WDT driver modules return ENODEV during modprobe if
no valid device was found, but w83697hf_wdt returns EIO.
Let w83697hf_wdt return ENODEV.
Signed-off-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull sparc fixes from David Miller:
"Three minor fixes from David Howells and Paul Gortmaker"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
Sparc: sparc_cpu_model isn't in asm/system.h any more [ver #2]
sparc32: make copy_to/from_user_page() usable from modular code
sparc32: fix build failure for arch_jump_label_transform
- Fix for a recent probing regression in the nouveau driver introduced
by an ACPI change related to the handling of _DSM from Jiang Liu.
- Fix for a dock station sysfs attribute that stopped working correctly
after recent changes in the ACPI core.
- cpufreq fix taking care of broken code related to CPU removal and
overlooked by a previous recent fix in that area. From Viresh Kumar.
- Two intel_pstate fixes related to Baytrail support added during
the 3.13 cycle (candidates for -stable) from Dirk Brandewie.
- ACPI video fix removing duplicate brightness values from the _BCL
table which makes its user space interface behave sanely. From
Hans de Goede.
- Fix for the powernow-k8 cpufreq driver making it initialize its
per-CPU data structures correctly from Srivatsa S. Bhat.
- Fix for an obscure memory leak in the ACPI PCI interrupt allocation
code (related to ISA) from Tomasz Nowicki.
- ACPI video blacklist changes moving several systems that should
use the native backlight interface instead of the ACPI one from
the general ACPI _OSI blacklist the the ACPI video driver's
blacklist where they belong. This consists of an ACPI video
driver update from Aaron Lu and a revert of a previous commit
adding systems to the ACPI _OSI blacklist requested by Takashi Iwai.
- Several fixes for build issues in ACPI drivers occuring when
CONFIG_PM_SLEEP is unset from Shuah Khan.
- Fix for an sscanf() format string in the ACPI Smart Battery
Subsystem (SBS) driver from Luis G.F.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5gW2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include two fixes for recent regressions related to ACPI, a
cpufreq fix for breakage overlooked by a previous fix commit, two
intel_pstate fixes for stuff added during the 3.13 cycle that need to
go into -stable, three fixes for older bugs that also are -stable
candidates, ACPI video blacklist changes related to BIOSes that behave
in a special way on Windows 8, several build fixes for CONFIG_PM_SLEEP
unset in ACPI drivers and an ACPI driver cleanup.
Specifics:
- Fix for a recent probing regression in the nouveau driver
introduced by an ACPI change related to the handling of _DSM from
Jiang Liu.
- Fix for a dock station sysfs attribute that stopped working
correctly after recent changes in the ACPI core.
- cpufreq fix taking care of broken code related to CPU removal and
overlooked by a previous recent fix in that area. From Viresh
Kumar.
- Two intel_pstate fixes related to Baytrail support added during the
3.13 cycle (candidates for -stable) from Dirk Brandewie.
- ACPI video fix removing duplicate brightness values from the _BCL
table which makes its user space interface behave sanely. From
Hans de Goede.
- Fix for the powernow-k8 cpufreq driver making it initialize its
per-CPU data structures correctly from Srivatsa S Bhat.
- Fix for an obscure memory leak in the ACPI PCI interrupt allocation
code (related to ISA) from Tomasz Nowicki.
- ACPI video blacklist changes moving several systems that should use
the native backlight interface instead of the ACPI one from the
general ACPI _OSI blacklist the the ACPI video driver's blacklist
where they belong. This consists of an ACPI video driver update
from Aaron Lu and a revert of a previous commit adding systems to
the ACPI _OSI blacklist requested by Takashi Iwai.
- Several fixes for build issues in ACPI drivers occuring when
CONFIG_PM_SLEEP is unset from Shuah Khan.
- Fix for an sscanf() format string in the ACPI Smart Battery
Subsystem (SBS) driver from Luis G.F"
* tag 'pm+acpi-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: Add support for Baytrail turbo P states
intel_pstate: Use LFM bus ratio as min ratio/P state
ACPI / nouveau: fix probing regression related to _DSM
Revert "ACPI: Blacklist Win8 OSI for some HP laptop 2013 models"
ACPI / video: Add systems that should favour native backlight interface
ACPI / video: Filter the _BCL table for duplicate brightness values
cpufreq: powernow-k8: Initialize per-cpu data-structures properly
cpufreq: remove sysfs link when a cpu != policy->cpu, is removed
ACPI / PCI: Fix memory leak in acpi_pci_irq_enable()
ACPI / dock: Make 'docked' sysfs attribute work as documented
ACPI / SBS: Fix incorrect sscanf() string
ACPI / thermal: fix thermal driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / SBS: fix SBS driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / fan: fix fan driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / button: fix button driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / battery: fix battery driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / AC: fix AC driver compile error when CONFIG_PM_SLEEP is undefined
The fixes are only for the ARM-SMMU driver. Here is the summary from
Will Deacon:
- Andreas Herrmann took the driver for a run with a real SATA
controller, which caused the new mutex-based locking to explode
since we require mappings in atomic context
- Yifan fixed an issue with the page table creation, which then caused
breakages with the way in which we flush descriptors out to the
table walker
- I ran the driver on a system where the SMMU is hooked into a
coherent interconnect for table walks, and noticed a shareability
mismatch between the CPU and the SMMU
These issues are all fixed here and have been tested on both arm and
arm64 based systems.
Besides that I put a fix on-top to make the spinlock irq-safe, so that the
code-paths can be used in the DMA-API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K+3P
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"The fixes are only for the ARM-SMMU driver. Here is the summary from
Will Deacon:
- Andreas Herrmann took the driver for a run with a real SATA
controller, which caused the new mutex-based locking to explode
since we require mappings in atomic context
- Yifan fixed an issue with the page table creation, which then
caused breakages with the way in which we flush descriptors out to
the table walker
- I ran the driver on a system where the SMMU is hooked into a
coherent interconnect for table walks, and noticed a shareability
mismatch between the CPU and the SMMU
These issues are all fixed here and have been tested on both arm and
arm64 based systems.
Besides that I put a fix on-top to make the spinlock irq-safe, so that
the code-paths can be used in the DMA-API"
* tag 'iommu-fixes-v3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
arm/smmu: Use irqsafe spinlock for domain lock
iommu/arm-smmu: fix compilation issue when !CONFIG_ARM_AMBA
iommu/arm-smmu: set CBARn.BPSHCFG to NSH for s1-s2-bypass contexts
iommu/arm-smmu: fix table flushing during initial allocations
iommu/arm-smmu: really fix page table locking
iommu/arm-smmu: fix pud/pmd entry fill sequence
This time we got a slightly higher volume than previous times,
but all device-specific good fixes. Noticeable changes are fixes in
davinci, and the removal of open-codes in HD-audio ca0132 driver.
The rest are all small fixes and/or quirks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=96St
-----END PGP SIGNATURE-----
Merge tag 'sound-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we got a slightly higher volume than previous times, but all
device-specific good fixes. Noticeable changes are fixes in davinci,
and the removal of open-codes in HD-audio ca0132 driver. The rest are
all small fixes and/or quirks"
* tag 'sound-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Enable front audio jacks on one HP desktop model
ALSA: hda/ca0132 - Fix recording from mode id 0x8
ALSA: hda/ca0132 - setup/cleanup streams
ALSA: hda - add headset mic detect quirks for two Dell laptops
ALSA: usb-audio: work around KEF X300A firmware bug
ASoC: max98090: make REVISION_ID readable
ASoC: txx9aclc_ac97: Fix kernel crash on probe
ASoC: max98090: sync regcache on entering STANDBY
ASoC: blackfin: Fix machine driver Kconfig dependencies
ASoC: da9055: Fix device registration of PMIC and CODEC devices
ASoC: fsl-esai: fix ESAI TDM slot setting
ASoC: fsl: fix pm support of machine drivers
ASoC: rt5640: Add ACPI ID for Intel Baytrail
ASoC: davinci-evm: Add pm callbacks to platform driver
ASoC: davinci-mcasp: Consolidate pm_runtime_get/put() use in the driver
ASoC: davinci-mcasp: Configure xxTDM, xxFMT and xxFMCT registers synchronously
ASoC: davinci-mcasp: Harmonize the sub hw_params function names
ASoC: samsung: Fix trivial typo
ASoC: samsung: Remove invalid dependencies
ASoC: wm8993: drop regulator_bulk_free of devm_ allocated data
Performing a Channel-Path configure on operation on a Channel-Path ID
(CHPID) does not trigger a scan for subchannels that might have become
available through that CHPID. As a result, some subchannels and
associated I/O devices might be missing. Fix this by adding the missing
scan.
This problem was introduced by commit c820de39, "[S390] cio: Rework
css driver.", but wasn't noticed earlier because the machine usually
also generates a Channel-Report-Word when the first CHPID of a
subchannel is configured on, resulting in a separate scan for that
subchannel. The problem only becomes apparent when this first CHPID is
not working properly and additional working CHPIDs are subsequently
configured on without any effect on the availability of the affected
subchannel.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* pm-cpufreq:
intel_pstate: Add support for Baytrail turbo P states
intel_pstate: Use LFM bus ratio as min ratio/P state
cpufreq: powernow-k8: Initialize per-cpu data-structures properly
cpufreq: remove sysfs link when a cpu != policy->cpu, is removed
* acpi-pm:
ACPI / thermal: fix thermal driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / SBS: fix SBS driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / fan: fix fan driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / button: fix button driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / battery: fix battery driver compile error when CONFIG_PM_SLEEP is undefined
ACPI / AC: fix AC driver compile error when CONFIG_PM_SLEEP is undefined
* acpi-video:
Revert "ACPI: Blacklist Win8 OSI for some HP laptop 2013 models"
ACPI / video: Add systems that should favour native backlight interface
ACPI / video: Filter the _BCL table for duplicate brightness values
A documentation update exposed the existance of the turbo ratio
register. Update baytrail support to use the turbo range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
LFM (max efficiency ratio) is the max frequency at minimum voltage
supported by the processor. Using LFM as the minimum P state
increases performmance without affecting power. By not using P states
below LFM we avoid using P states that are less power efficient.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes to 2 Capella light sensor drivers where the units of the integration
time reported to userspace were out be a factor of a thousand.
These patches are as large as they are purely due to a variable rename
tied up with the incorrect scale. The actual change is only a couple of lines.
1 patch dropping L3GD20H from the st gyroscope driver. It never actually
worked as the address set is different from any others supported by the
driver currently. An additional patch enables correct support for this
part but is too large to sensibly apply as a fix to some support that never
actually allowed the driver to be successfully probed on this part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LLV9
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.14c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
Third round of fixes for IIO in the 3.14 cycle.
Fixes to 2 Capella light sensor drivers where the units of the integration
time reported to userspace were out be a factor of a thousand.
These patches are as large as they are purely due to a variable rename
tied up with the incorrect scale. The actual change is only a couple of lines.
1 patch dropping L3GD20H from the st gyroscope driver. It never actually
worked as the address set is different from any others supported by the
driver currently. An additional patch enables correct support for this
part but is too large to sensibly apply as a fix to some support that never
actually allowed the driver to be successfully probed on this part.
Change "dummy supplies not allowed" error message to warning instead, as this
is a just warning message with no change to the behavior.
[Added a CC to stable since some other bug fixes cause this to come up
more frequently on PCs which is how it was noticed -- broonie]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AnZJ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.14-rc4
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch fixes the NAA formatted name used by EVPD=0x83
device identifer to reflect the proper NPIV enabled WWPN.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch performs configfs_depend_item() during TPG enable for
base_tpg (eg: non-NPIV) ports, and configfs_undepend_item() during
TPG disable for base_tpg.
This is done to ensure that any attempt to configfs rmdir a base_tpg
with active NPIV ports will fail with -EBUSY, until all associated
NPIV ports have been explicitly shutdown and base_tpg disabled.
Note that the actual configfs_[un]depend_item() is done from seperate
process context, as these are not intended to be called directly
from configfs callbacks.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds seperate logic for NPIV specific enable/disable
attribute logic, as NPIV vs. non-NPIV enable/disable ends up being
different enough to warrent seperate logic for setting configfs
tpg_group dependencies in the non-NPIV case.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an check to qlt_stop_phase1() to avoid shutdown
when the base_vha contains a non-zero fc_host->npiv_vports_inuse
count.
This includes holding qla_tgt_mutex in qlt_stop_phase1() between
the fc_host->npiv_vports_inuse check + setting of tgt->tgt_stop to
avoid a possible race between qlt_lport_register() -> tcm_qla2xxx
-> tcm_qla2xxx_lport_register_npiv_cb() calling fc_vport_create().
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch closes a race between qlt_lport_register() and
tcm_qla2xxx callback logic by holding qla_tgt_mutex before
making the callback.
In order for this to work, the qlt_add_target() and
qlt_remove_target() code has been changed to avoid the
accessing qla_tgt_mutex + list_[add,del] for NPIV enabled
ports.
This bug introduced in v3.14-rc1 code with commit 49a47f2.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver concatenates multiple packets in one MMC transfer. For
scatter-gather to work the total length need to be multiple of 512
bytes. A pre-allocated buffer was used to add padding to accomplish
that. However, the length was not properly set and it was freed after
the first transfer causing a crash.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.
Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan results from Marvell 8388 and 8686 have probe responses from
hidden APs and OLPC XO-1 mesh with a zero length SSID IE.
Bug in lbs_ret_scan discarded any remaining BSS in scan response,
leading to user not seeing APs in dense environments.
With LBS_DEB_SCAN, dmesg shows
libertas scan: scan response: 5 BSSs (419 bytes); resp size 474 bytes
libertas scan: scan: 00:1a:2b:84:de:e8, capa 0401, chan 1, qz, -51 dBm
libertas scan: scan: 5c:63:bf:d8:eb:0c, capa 0411, chan 1, qw129, -23 dBm
libertas scan: scan response: invalid IE fmt
With LBS_DEB_HEX, dmesg shows valid BSS in scan response were not
processed.
Change is to ignore zero length IE and continue processing.
Fixes OLPC 12757, http://dev.laptop.org/ticket/12757
Signed-off-by: James Cameron <quozl@laptop.org>
Reported-by: T Gillett <tgillett@gmail.com>
Tested-by: T Gillett <tgillett@gmail.com>
CC: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function del_timer() does not guarantee that timer was really deleted.
If the timer handler is beeing executed at the moment, the function
does nothing. So, it's possible to use already freed memory in the handler:
[ref: Documentation/DocBook/kernel-locking.tmpl]
This was found using grep and compile-tested only. Please, consider
applying or something similar to it.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
CC: Jouni Malinen <j@w1.fi>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CTv7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most interesting thing here is the change to enable INTx (by
clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
Apparently the Baytrail BIOS does this, which means EHCI doesn't work.
Also, fix an AHCI MSI regression and other issues with the recent MSI
changes. This also adds pci_enable_msi_exact() and
pci_enable_msix_exact(), which aren't regression fixes, but will keep
us from touching drivers twice (once to stop using the deprecated
pci_enable_msi(), etc., and again to use the *_exact() variants).
There's also a minor MVEBU fix.
Summary:
MSI:
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous:
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"
* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ahci: Fix broken fallback to single MSI mode
PCI: Enable INTx if BIOS left them disabled
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
PCI: mvebu: Use Device ID and revision from underlying endpoint
Fix regression caused by commit b072e53, which breaks loading nouveau
driver on optimus laptops.
On some platforms, ACPI _DSM method (nouveau_op_dsm_muid, function 0)
has special requirements on the fourth parameter, which is different
from ACPI specifications. So revert to the private implementation
to check availability of _DSM functions instead of using common
acpi_check_dsm() interface.
Fixes: b072e53b0a (ACPI / nouveau: replace open-coded _DSM code with helper functions)
Reported-and-tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
[rjw: Subject]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull libata fixes from Tejun Heo:
"Various device specific fixes. Nothing too interesting"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable NCQ on Samsung pci-e SSDs on macbooks
ata: sata_mv: Cleanup only the initialized ports
sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
ata: enable quirk from jmicron JMB350 for JMB394
ATA: SATA_MV: Add missing Kconfig select statememnt
ata: pata_imx: Check the return value from clk_prepare_enable()
sparc_cpu_model isn't in asm/system.h any more, so remove a comment
about it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.
There has potential issue like as:
CPU fec uDMA
Set tx ready bit
uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...
Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tegra124 does not have gr2d and gr3d clocks. They have been replaced by the
vic03 and gpu clocks respectively.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
schedule_delayed_work() takes the delay in jiffies, not msecs.
This bug slipped in with the recent reset logic cleanup
(8ed1fb790e: "usb: musb: finish suspend/reset work independently from
musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both the PM_RUNTIME and PM_SLEEP callbacks call into the common
msm_otg_{suspend,resume} routines, however these routines are only being
built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also
depends on msm_hsusb_config_vddcx(), which is only built when
CONFIG_PM_SLEEP.
Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the
preprocessor conditional, and moving msm_hsusb_config_vddcx().
While we're here, eliminate the CONFIG_PM conditional for setting
up the dev_pm_ops.
This address the following errors Russell King has hit doing randconfig
builds:
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend'
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix possible NULL pointer dereference introduced in
commit 219580e (usb: f_fs: check quirk to pad epout
buf size when not aligned to maxpacketsize)
In cases we do wait with:
wait_event_interruptible(epfile->wait, (ep = epfile->ep));
for endpoint to be enabled, functionfs_bind() has not been called yet
and epfile->ffs->gadget is still NULL and the automatic variable 'gadget'
has been initialized with NULL at the point of its definition.
Later on it is used as a parameter to:
usb_ep_align_maybe(gadget, ep->ep, len)
which in turn dereferences it.
This patch fixes it by moving the actual assignment to the local 'gadget'
variable after the potential waiting has completed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to use gadget_is_otg to check if the gadget is really
otg support at runtime, other composite gadget drivers have already
followed this method.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As the lock might be used through DMA-API which is allowed
in interrupt context.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Adds a selftest function for the of_match_node function. of_match_node
is supposed to handle precedence for the compatible property as well as
the name and device_type values. This patch adds some test case data and
a function that makes sure each test node matches against the correct
entry of an of_device_id table.
This code was written to verify the new of_match_node() implementation
that is an earlier part of this series.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Kevin Hao <haokexin@gmail.com>
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
In the current implementation of __of_match_node(), it will compare
each given match entry against all the node's compatible strings
with of_device_is_compatible().
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and
also an alphabetical ordering is more sane there.
Therefore, we define a following priority order for the match, and
then scan all the entries to find the best match.
1. specific compatible && type && name
2. specific compatible && type
3. specific compatible && name
4. specific compatible
5. general compatible && type && name
6. general compatible && type
7. general compatible && name
8. general compatible
9. type && name
10. type
11. name
v5: Fix nested locking bug
v4: Short-circuit failure cases instead of mucking with score, and
remove extra __of_device_is_compatible() wrapper stub.
Move scoring logic directly into __of_device_is_compatible()
v3: Also need to bail out when there does have a compatible member in match
entry, but it doesn't match with the device node's compatible.
v2: Fix the bug such as we get the same score for the following two match
entries with the empty node 'name2 { };'
struct of_device_id matches[] = {
{.name = "name2", },
{.name = "name2", .type = "type1", },
{}
};
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[grant.likely: added v4 changes]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.
This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
snd_soc_dapm_sync takes the dapm_mutex internally, but we currently take
it externally as well. This patch fixes this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Even though only the outer vlan tag can be HW accelerated in the transmission
path, in the TUN/TAP driver vlan_features mirrors hw_features, which happens
to have the NETIF_F_HW_VLAN_?TAG_TX flags set. Because of this, during packet
tranmisssion through a stacked vlan device dev_hard_start_xmit, (incorrectly)
assuming that the vlan device supports hardware vlan acceleration, does not
add the vlan header to the skb payload and the inner vlan tags are lost
(vlan_tci contains the outer vlan tag when userspace reads the packet from
the tap device).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we create a stacked vlan interface such as veth0.10.20, it sends
single tagged frames (tagged with only vid 10).
Because vlan_features of a veth interface has the
NETIF_F_HW_VLAN_[CTAG/STAG]_TX bits, veth0.10 also has that feature, so
dev_hard_start_xmit(veth0.10) doesn't call __vlan_put_tag() and
vlan_dev_hard_start_xmit(veth0.10) overwrites vlan_tci.
This prevents us from using a combination of 802.1ad and 802.1Q
in containers, etc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These patches contain a fix for a potential hang when the RGB output is
disabled twice, a typofix that prevents the framebuffer console from
being restored on ->lastclose() and an optimization to do as little work
as possible during host1x job submission.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=pQjy
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc3' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v3.14-rc3
These patches contain a fix for a potential hang when the RGB output is
disabled twice, a typofix that prevents the framebuffer console from
being restored on ->lastclose() and an optimization to do as little work
as possible during host1x job submission.
* tag 'drm/for-3.14-rc3' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Add guard to avoid double disable/enable of RGB outputs
gpu: host1x: do not check previously handled gathers
drm/tegra: fix typo 'CONFIG_TEGRA_DRM_FBDEV'
This reverts commit 2d4054d842 (ACPI: Blacklist Win8 OSI for some HP
laptop 2013 models) that is not necessary any more after previous
commit 1811fcb029fa (ACPI / video: Add systems that should favour native
backlight interface).
Requested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some system's ACPI video backlight control interface is broken and the
native backlight control interface should be used by default. This patch
sets the use_native_backlight parameter to true for those systems so
that video backlight control interface will not be created. For detailed
models that are added here, reference the following list.
Note that the user specified kernel cmdline option will always have the
highest priority, i.e. if use_native_backlight=0 is specified and the
system is in the DMI table, the video module will not skip registering
backlight interface for it.
Thinkpad T430s:
Reported-by: Theodore Tso <tytso@mit.edu>
Reported-and-tested-by: Peter Weber <bugs@ttyhoney.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Thinkpad X230:
Reported-and-tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
ThinkPad X1 Carbon:
Reported-and-tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Lenovo Yoga 13:
Reported-by: Lennart Poettering <lennart@poettering.net>
Reported-and-tested-by: Kevin Smith <thirdwiggin@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=63811
Dell Inspiron 7520:
Reported-by: Rinat Ibragimov <ibragimovrinat@mail.ru>
Acer Aspire 5733Z:
Reported-by: <sov.info@mail.ru>
References: https://bugzilla.kernel.org/show_bug.cgi?id=62941
Acer Aspire V5-431:
Reported-by: Thomas Christensen <christensenthomas@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=68751
HP ProBook 4340s:
Reported-and-tested-by: Vladimir Sherenkov <a_12300@mail.ru>
References: http://redmine.russianfedora.pro/issues/1258
HP EliteBook/ProBook 2013 models, ZBook and some others:
Provided-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices have duplicate entries in there brightness levels table, ie
on my Dell Latitude E6430 the table looks like this:
[ 3.686060] acpi backlight index 0, val 80
[ 3.686095] acpi backlight index 1, val 50
[ 3.686122] acpi backlight index 2, val 5
[ 3.686147] acpi backlight index 3, val 5
[ 3.686172] acpi backlight index 4, val 5
[ 3.686197] acpi backlight index 5, val 5
[ 3.686223] acpi backlight index 6, val 5
[ 3.686248] acpi backlight index 7, val 5
[ 3.686273] acpi backlight index 8, val 6
[ 3.686332] acpi backlight index 9, val 7
[ 3.686356] acpi backlight index 10, val 8
[ 3.686380] acpi backlight index 11, val 9
etc.
Notice that brightness values 0-5 are all mapped to 5. This means that
if userspace writes any value between 0 and 5 to the brightness sysfs attribute
and then reads it, it will always return 0, which is somewhat unexpected.
This is a problem for ie gnome-settings-daemon, which uses read-modify-write
logic when the users presses the brightness up or down keys. This is done
this way to take brightness changes from other sources into account.
On this specific laptop what happens once the brightness has been set to 0,
is that gsd reads 0, adds 5, writes 5, and on the next brightness up key press
again reads 0, so things get stuck at the lowest brightness setting.
Filtering out the duplicate table entries, makes any write to brightness
read back as the written value as one would expect, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ed1f50c3a ("net: add skb_checksum_setup") we introduced some checksum
functions in core driver. Subsequent change b5cf66cd1 ("xen-netfront:
use new skb_checksum_setup function") made use of those functions to
replace its own implementation.
However with that change netfront is broken. It sees a lot of checksum
error. That's because its own implementation of checksum function was a
bit hacky (dereferencing skb->data directly) while the new function was
implemented using ip_hdr(). The network header is not reset before skb
is passed to the new function. When the new function tries to do its
job, it's confused and reports error.
The fix is simple, we need to reset network header before passing skb to
checksum function. Netback is not affected as it already does the right
thing.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Tested-By: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple of small issues solved:
- Suspend/Resume call-backs require CONFIG_PM_SLEEP
- Some drivers written for 32bit architectures fail when compiled
with a 64bit compiler. The fixes will future proof the drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=705r
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.14-1' of git://git.linaro.org/people/lee.jones/mfd
Pull MFD fixes from Lee Jones:
"Couple of small issues solved:
- Suspend/Resume call-backs require CONFIG_PM_SLEEP
- Some drivers written for 32bit architectures fail when compiled
with a 64bit compiler. The fixes will future proof the drivers"
* tag 'mfd-fixes-3.14-1' of git://git.linaro.org/people/lee.jones/mfd:
mfd: sec-core: sec_pmic_{suspend,resume}() should depend on CONFIG_PM_SLEEP
mfd: max14577: max14577_{suspend,resume}() should depend on CONFIG_PM_SLEEP
mfd: tps65217: Naturalise cross-architecture discrepancies
mfd: wm8994-core: Naturalise cross-architecture discrepancies
mfd: max8998: Naturalise cross-architecture discrepancies
mfd: max8997: Naturalise cross-architecture discrepancies
If CONFIG_PM_SLEEP=n:
drivers/mfd/sec-core.c:349: warning: ‘sec_pmic_suspend’ defined but not used
drivers/mfd/sec-core.c:371: warning: ‘sec_pmic_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If CONFIG_PM_SLEEP=n:
drivers/mfd/max14577.c:177: warning: ‘max14577_suspend’ defined but not used
drivers/mfd/max14577.c:200: warning: ‘max14577_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:
drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
warning: cast from pointer to integer of different size
chip_id = (unsigned int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the WM8994 for a 64bit architecture we receive the following
warnings:
drivers/mfd/wm8994-core.c: In function ‘wm8994_i2c_probe’:
drivers/mfd/wm8994-core.c:639:19:
warning: cast from pointer to integer of different size
wm8994->type = (int)of_id->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
drivers/mfd/max8998.c:178:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
drivers/mfd/max8997.c:173:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
bus_num might be asigned dynamically to e.g. 32766. In this case the
calculated DMA channel based on SPI bus number is bogus. Use SPI channel
number instead for calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The qspi clock divisor is incorrectly set to twice the value it should
have, possibly because it has been computed based on PLL1 as the clock
parent instead of PLL1 / 2 (the datasheets specifies the qspi nominal
frequencies, not the divisor values). Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The lb, qspi, sdh, sd0 and sd1 clocks have the PLL1 (divided by 2) as
their parent, not the main clock. Fix it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull drm fixes from Dave Airlie:
"Lots of little small things, nothing too major: nouveau regression
fixes, vmware fixes for the new hw support, memory leaks in error path
fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm/radeon/ni: fix typo in dpm sq ramping setup
drm/radeon/si: fix typo in dpm sq ramping setup
drm/radeon: fix CP semaphores on CIK
drm/radeon: delete a stray tab
drm/radeon: fix display tiling setup on SI
drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
drm/radeon: fill in DRM_CAPs for cursor size
drm: add DRM_CAPs for cursor size
drm/radeon: unify bpc handling
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
drm/nv50/disp: use correct register to determine DP display bpp
drm/nouveau/fb: use correct ram oclass for nv1a hardware
drm/nv50/gr: add missing nv_error parameter priv
drm/nouveau: fix ENG_RUNLIST register address
drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
drm/nv4c/vga: decode register is in a different place on nv4x igp's
drm/nv4c/mc: nv4x igp's have a different msi rearm register
drm/nouveau: set irq_enabled manually
...
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311
Reported-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 42f921a (cpufreq: remove sysfs files for CPUs which failed to
come back after resume) tried to do this but missed this piece of code
to fix.
Currently we are getting this on suspend/resume:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 877 at fs/sysfs/dir.c:52 sysfs_warn_dup+0x68/0x84()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu1/cpufreq'
Modules linked in: brcmfmac brcmutil
CPU: 0 PID: 877 Comm: test-rtc-resume Not tainted 3.14.0-rc2-00259-g9398a10cd964 #12
[<c0015bac>] (unwind_backtrace) from [<c0011850>] (show_stack+0x10/0x14)
[<c0011850>] (show_stack) from [<c056e018>] (dump_stack+0x80/0xcc)
[<c056e018>] (dump_stack) from [<c0025e44>] (warn_slowpath_common+0x64/0x88)
[<c0025e44>] (warn_slowpath_common) from [<c0025efc>] (warn_slowpath_fmt+0x30/0x40)
[<c0025efc>] (warn_slowpath_fmt) from [<c012776c>] (sysfs_warn_dup+0x68/0x84)
[<c012776c>] (sysfs_warn_dup) from [<c0127a54>] (sysfs_do_create_link_sd+0xb0/0xb8)
[<c0127a54>] (sysfs_do_create_link_sd) from [<c038ef64>] (__cpufreq_add_dev.isra.27+0x2a8/0x814)
[<c038ef64>] (__cpufreq_add_dev.isra.27) from [<c038f548>] (cpufreq_cpu_callback+0x70/0x8c)
[<c038f548>] (cpufreq_cpu_callback) from [<c0043864>] (notifier_call_chain+0x44/0x84)
[<c0043864>] (notifier_call_chain) from [<c0025f60>] (__cpu_notify+0x28/0x44)
[<c0025f60>] (__cpu_notify) from [<c00261e8>] (_cpu_up+0xf0/0x140)
[<c00261e8>] (_cpu_up) from [<c0569eb8>] (enable_nonboot_cpus+0x68/0xb0)
[<c0569eb8>] (enable_nonboot_cpus) from [<c006339c>] (suspend_devices_and_enter+0x198/0x2dc)
[<c006339c>] (suspend_devices_and_enter) from [<c0063654>] (pm_suspend+0x174/0x1e8)
[<c0063654>] (pm_suspend) from [<c00624e0>] (state_store+0x6c/0xbc)
[<c00624e0>] (state_store) from [<c01fc200>] (kobj_attr_store+0x14/0x20)
[<c01fc200>] (kobj_attr_store) from [<c0126e50>] (sysfs_kf_write+0x44/0x48)
[<c0126e50>] (sysfs_kf_write) from [<c012a274>] (kernfs_fop_write+0xb4/0x14c)
[<c012a274>] (kernfs_fop_write) from [<c00d4818>] (vfs_write+0xa8/0x180)
[<c00d4818>] (vfs_write) from [<c00d4bb8>] (SyS_write+0x3c/0x70)
[<c00d4bb8>] (SyS_write) from [<c000e620>] (ret_fast_syscall+0x0/0x30)
---[ end trace 76969904b614c18f ]---
Fix this by removing sysfs link for cpufreq directory when cpu removed
isn't policy->cpu.
Revamps: 42f921a (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v3.2+
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Pull networking fixes from David Miller:
1) kvaser CAN driver has fixed limits of some of it's table, validate
that we won't exceed those limits at probe time. Fix from Olivier
Sobrie.
2) Fix rtl8192ce disabling interrupts for too long, from Olivier
Langlois.
3) Fix botched shift in ath5k driver, from Dan Carpenter.
4) Fix corruption of deferred packets in TIPC, from Erik Hugne.
5) Fix newlink error path in macvlan driver, from Cong Wang.
6) Fix netpoll deadlock in bonding, from Ding Tianhong.
7) Handle GSO packets properly in forwarding path when fragmentation is
necessary on egress, from Florian Westphal.
8) Fix axienet build errors, from Michal Simek.
9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
Tsirkin.
10) Carrier status isn't set properly in hyperv driver, from Haiyang
Zhang.
11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.
12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
queue selection method. Add a fallback method mechanism to fix this
bug, from Daniel Borkmann.
13) Fix regression in link local route handling on GRE tunnels, from
Nicolas Dichtel.
14) Bonding can assign dup aggregator IDs in some sequences of
configuration, fix by making the allocation counter per-bond instead
of global. From Jiri Bohac.
15) sctp_connectx() needs compat translations, from Daniel Borkmann.
16) Fix of_mdio PHY interrupt parsing, from Ben Dooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
MAINTAINERS: add entry for the PHY library
of_mdio: fix phy interrupt passing
net: ethernet: update dependency and help text of mvneta
NET: fec: only enable napi if we are successful
af_packet: remove a stray tab in packet_set_ring()
net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
ipv4: fix counter in_slow_tot
irtty-sir.c: Do not set_termios() on irtty_close()
bonding: 802.3ad: make aggregator_identifier bond-private
usbnet: remove generic hard_header_len check
gre: add link local route when local addr is any
batman-adv: fix potential kernel paging error for unicast transmissions
batman-adv: avoid double free when orig_node initialization fails
batman-adv: free skb on TVLV parsing success
batman-adv: fix TT CRC computation by ensuring byte order
batman-adv: fix potential orig_node reference leak
batman-adv: avoid potential race condition when adding a new neighbour
batman-adv: properly check pskb_may_pull return value
batman-adv: release vlan object after checking the CRC
batman-adv: fix TT-TVLV parsing on OGM reception
...
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.
Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:
- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above
This fixes the issue:
net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI
to the correct:
net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.
In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After several experiments, deduced the the optimal number of unaligned
writes to be 2. Changing the value accordingly.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This reverts commit 06b29e76a7.
As pointed out by Grant Likely, we should also take the type and name
into account when searching the best compatible match. That means the
match with compatible, type and name should be better than the match
just with the same compatible string. So revert this and we will
implement another method to find the best match entry.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull request of 2014-02-18
One compile fix and one memory leak.
* tag 'ttm-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
Pull request of 2014-02-18.
Nothing special. The biggest change is adding a couple of command defines and
packing the command data correctly.
* tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix command defines and checks
drm/vmwgfx: Fix possible integer overflow
drm/vmwgfx: Remove stray const
drm/vmwgfx: unlock on error path in vmw_execbuf_process()
drm/vmwgfx: Get maximum mob size from register SVGA_REG_MOB_MAX_SIZE
drm/vmwgfx: Fix a couple of sparse warnings and errors
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream...
For the iwlwifi one, Emmanuel says:
"As explicitly written in the commit message, we prefer to disable Tx
AMPDU on NICs supported by iwldvm. This feature gives a big boost in
Tx performance, but the firmware is buggy and we can't rely on it.
Our hope is that most of the users out there want wifi to surf on
the web which means that they care more for Rx traffic than for Tx.
People who want to enable it can do so with the help of a module
parameter."
On top of that...
Dan Carpenter fixes a typo/thinko in ath5k.
Olivier Langlois fixes a couple of rtlwifi issues, one which leaves
IRQs disabled too long (causing a variety of problems elsewhere),
and one which fixes an incorrect return code when failing to enable
the NIC.
Russell King fixes a NULL pointer dereference in hostap.
Stanislaw Gruszka fixes a DMA coherence issue in the rtl8187 driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering phy_provider before creating the PHY can result in PHY
callbacks being invoked which will lead to aborts. In order to avoid this
invoke phy_provider_register after phy_create and phy_set_drvdata.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/phy/phy.h has stub code in there for when building without the
phy-core enabled. This is useful for generic drivers such as ahci-platform,
ehci-platoform and ohci-platform which have support for driving an optional
phy passed to them through the devicetree.
Since on some boards this phy functionality is not needed, being able to
disable the phy subsystem without needing a lot of #ifdef magic in the
driver using it is quite useful.
However this breaks when the module using the phy subsystem is build-in and
the phy-core is not, which leads to the build failing with missing symbol
errors in the linking stage of the zImage.
Which leads to gems such as this being added to the Kconfig for achi_platform:
depends on GENERIC_PHY || !GENERIC_PHY
Rather then duplicating this code in a lot of places using the phy-core,
I believe it is better to simply not allow the phy-core to be built as a
module. The phy core is quite small and has no external dependencies, so
always building it in when enabling it should not be an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-core allows phy_init and phy_power_on to be called multiple times,
but before this patch -ENOSUPP from phy_pm_runtime_get_sync would be
propagated to the caller for the 2nd and later calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In various cases errors may be expected, ie probe-deferral or a call to
phy_get from a driver where the use of a phy is optional.
Rather then adding all sort of complicated checks for this, and/or adding
special functions like devm_phy_get_optional, simply don't log an error,
and let deciding if get_phy returning an error really should result in a
dev_err up to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/phy/phy-bcm-kona-usb2.c:114: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
schedule_delayed_work() takes the delay in jiffies, not msecs. Fix the
caller sites in musb. This bug caused regressions with the cleanups
that went in for 3.14 (8ed1fb790e: "usb: musb: finish suspend/reset
work independently from musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static checkers complain that probably curly braces were intended here,
but actually it makes more sense to remove the extra tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most laptops seems to have a vblank period of less than
300 and mclk switching works fine. Drop the quirk and
set the default threshold to 200.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=70701
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some hardware may not support standard 64x64 cursors. Add
a drm cap to query the cursor size from the kernel. Some examples
include radeon CIK parts (128x128 cursors) and armada (32x64 or 64x32).
This allows things like device specific ddxes to remove asics specific
logic and also allows xf86-video-modesetting to work properly with hw
cursors on this hardware. Default to 64 if the driver doesn't specify
a size.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
We were already storing the bpc (bits per color) information
in radeon_crtc, so just use that everywhere rather than
calculating it everywhere we use it. This also allows us
to change it in one place if we ever want to override it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742d3
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):
drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.
e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.
[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When restoring bi_end_io, increase bi_remaining before retrying the bio
to avoid BUG_ON(atomic_read(&bio->bi_remaining) <= 0) in bio_endio().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fix a memory leak found by cppcheck.
[drivers/gpu/drm/ttm/ttm_agp_backend.c:129]:
(error) Memory leak: agp_be
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver was not able to manage the sensor: during probe function
and wai check, the driver stops and writes: "device name and WhoAmI mismatch."
The correct value of L3GD20H wai is 0xd7 instead of 0xd4.
Dropped support for the sensor.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Integration time of cm32181 is guessed about milliseconds.
But cm32181_read_als_it function return IIO_VAL_INT.
So fixed to return IIO_VAL_INT_PLUS_MICRO.
Next, add .write_raw_get_fmt callback function for call iio_str_to_fixpoint.
v2: cm32181_write_als_id function fixed as it was.
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch is fixed [read/write] integration time function.
cm36651 have integration time from 1 to 640 milliseconds.
But, print more then the thousand second. when call *_integration_time attribute.
Because read_integration_time function return IIO_VAL_INT.
read integration time function is changed return IIO_VAL_INT_PLUS_MICRO;
And then .write_raw_get_fmt callback function for parse a fixed-point number from a string.
Some description is revised milliseconds unit.
v2: cm36651_write_int_time function fixed as it was.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Nothing too exciting, mostly fixes for ancient boards, but a pretty important fix for DP on some systems.
Thanks,
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
drm/nv50/disp: use correct register to determine DP display bpp
drm/nouveau/fb: use correct ram oclass for nv1a hardware
drm/nv50/gr: add missing nv_error parameter priv
drm/nouveau: fix ENG_RUNLIST register address
drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
drm/nv4c/vga: decode register is in a different place on nv4x igp's
drm/nv4c/mc: nv4x igp's have a different msi rearm register
drm/nouveau: set irq_enabled manually
3 fixes plus 1 prep patch, all four cc: stable. Jani will take over from
here and the plan is that he'll do 3.14-fixes for the entire release just
to work things out a bit.
* tag 'drm-intel-fixes-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915/dp: add native aux defer retry limit
drm/i915/dp: increase native aux defer retry timeout
drm/i915: Prevent MI_DISPLAY_FLIP straddling two cachelines on IVB
drm/i915: Add intel_ring_cachline_align()
fix for leak in tda998x
* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: Fix memory leak in tda998x_encoder_init error path.
Commit a55409066 ("drm/nv50-: map TTM_PL_SYSTEM through a BAR for CPU
access") made it possible to work with tiled memory. However
mem->mm_node is not a nouveau_mem for AGP-using pre-NV50 cards, but a
drm_mm_node, as created by the ttm_bo_manager_func. As such, extend the
untiled check to explicitly include all pre-nv50 cards.
Reported-by: Ronald <ronald645@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74613
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Tested-by: Ronald Uitermark <ronald645@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit 0a0afd282f ("drm/nv50-/disp: move DP link training to core and
train from supervisor") added code that uses the wrong register for
computing the display bpp, used for bandwidth calculation. Adjust to use
the same register as used by exec_clkcmp and nv50_disp_intr_unk20_2_dp.
Reported-by: Torsten Wagner <torsten.wagner@gmail.com>
Reported-by: Michael Gulick <mgulick@mathworks.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67628
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
commit 8613e7314a
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Oct 21 08:50:25 2013 +1000
drm/nouveau/fb: remove ram oclass argument from base fb constructor
Introduced a unfortunate regression by using nv10 ram oclass for nv1a
hardware, causing corruption and eventually system lockup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74866
Reported-by: John F. Godfrey <jfgodfrey@gmail.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit ea7dce901 ("drm/nv50/gr: print mpc trap name when it's not an mp
trap") added an nv_error call that was missing the priv parameter. This
causes GPFs if the error is ever hit.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Address of the ENG_RUNLIST register should be 0x002284 + (engine * 8),
not 0x002284 + (engine * 4).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
See https://bugs.freedesktop.org/show_bug.cgi?id=74492
Reported-by: Ronald <ronald645@gmail.com>
Suggested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since commit 0fa9061ae8 ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Issuing set_termios() from irtty_close() causes kernel Oops for
unplugged usb-serial devices.
Since no other tty_ldisc calls set_termios() on close and no tty driver
seem to check if tty->device_data is NULL or not on entry to set_termios(),
the only solution I can come up with is to remove the irtty_stop_receiver()
call, which only updates termios.
Signed-off-by: Tommie Gannert <tommie@gannert.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need at least HID_MAX_BUFFER_SIZE (4096) bytes as input buffer. HID
core depends on this as it requires every input report to be at least as
big as advertised.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 003b5c5719 ("block: Convert drivers
to immutable biovecs") broke dm-mirror due to dm-io breakage.
dm-io had three possible iterators (DM_IO_PAGE_LIST, DM_IO_BVEC,
DM_IO_VMA) that iterate over pages where the I/O should be performed.
The switch to immutable biovecs changed the DM_IO_BVEC iterator to
DM_IO_BIO. Before this change the iterator stored the pointer to a bio
vector in the dpages structure. The iterator incremented the pointer in
the dpages structure as it advanced over the pages. After the immutable
biovecs change, the DM_IO_BIO iterator stores a pointer to the bio in
the dpages structure and uses bio_advance to change the bio as it
advances.
The problem is that the function dispatch_io stores the content of the
dpages structure into the variable old_pages and restores it before
issuing I/O to each of the devices. Before the change, the statement
"*dp = old_pages;" restored the iterator to its starting position.
After the change, struct dpages holds a pointer to the bio, thus the
statement "*dp = old_pages;" doesn't restore the iterator.
Consequently, in the context of dm-mirror: only the first mirror leg is
written correctly, the kernel locks up when trying to write the other
mirror legs because the number of sectors to write in the where->count
variable doesn't match the number of sectors returned by the iterator.
This patch fixes the bug by partially reverting the original patch - it
changes the code so that struct dpages holds a pointer to the bio vector,
so that the statement "*dp = old_pages;" restores the iterator correctly.
The field "context_u" holds the offset from the beginning of the current
bio vector entry, just like the "bio->bi_iter.bi_bvec_done" field.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 905e51b ("dm thin: commit outstanding data every second")
introduced a periodic commit. This commit occurs regardless of whether
any thin devices have made changes.
Fix the periodic commit to check if any of a pool's thin devices have
changed using dm_pool_changed_this_transaction().
Reported-by: Alexander Larsson <alexl@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
When completing an overwrite bio, in overwrite_endio(), the associated
migration should not be added to the 'completed_migrations' until the
bio's fields are restored with dm_unhook_bio().
Otherwise, do_worker() can race to process 'completed_migrations' before
dm_unhook_bio() -- so the bio's bi_end_io is incorrect. This is
unlikely to cause any problems given the current code but should be
fixed on the basis of correctness.
Also, the cache's spinlock only needs to be held when manipulating the
'completed_migrations' list -- other changes don't need protection.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Commit c9d28d5d ("dm cache: promotion optimisation for writes")
incorrectly placed the 'hook_info' member in the writethrough-only
portion of the per_bio_data structure.
Given that the overwrite optimization may be used for writeback the
'hook_info' member must be placed above the 'cache' member of the
per_bio_data structure. Any members above 'cache' are available from
both writeback and writethrough modes' per_bio_data structure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
When requesting a rate less than the minimum clock rate for a divider,
use the maximum divider value instead of bailing out with an error.
This matches the behavior of the generic clock divider.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
When pll_x is the parent of cclk_lp, PLLX_DIV2_BYPASS_LP determines
whether cclk_lp output is divided by 2. Set TEGRA_DIVIDER_2 so that
the clk_super driver is aware of this.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The sdmmc clocks on Tegra114 and Tegra124 are 3-bit wide muxes with
6 parents. Add support for tegra_clk_sdmmc*_8 and switch Tegra114
and Tegra124 to use these clocks instead.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
The host1x clock on Tegra124 is a 3-bit wide mux with 6 parents.
Change thte id to tegra_clk_host1x_8 so that the correct clock gets
registered.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Set correct pll_d2_out0 divider and correct the p div values for pll_d2.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
PLLD was using the same mnp table as PLLP. Fix it to use its own
table which is different from PLLP's.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
This table had settings for 216MHz, but PLLP is (and is supposed to be)
configured at 408MHz. If that table is used and PLLP_BASE_OVRRIDE is
not set, the kernel will panic in clk_pll_recalc_rate().
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Add clocks required for accessing fuses on Tegra20.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
We look for usage id for "power and report state", and modify
logical minimum value to 1.
This is a follow-up patch to commit id 875e36f8.
Signed-off-by: Archana Patni <archana.patni@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It appears that in the DMA40 driver the DMA tasklet will very
often dereference memory for a descriptor just free:d from the
DMA40 slab. Nothing happens because no other part of the driver
has yet had a chance to claim this memory, but it's really
nasty to dereference free:d memory, so let's check the flag
before the descriptor is free and store it in a bool variable.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the device is not completely shut down.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, the "cat /sys/class/net/ethN/operstate" shows
"unknown", and "ethtool ethN" shows "Link detected: yes", when VM
boots up with or without vNIC connected.
This patch fixed the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTABFuAAoJEMhvYp4jgsXi2PkH/1F9qpuZ1MAHCqu5scBbozKt
LST0Q2qfspl+PjEN30D2X4S6O0qhHeEjeC96AfNUqpJ6sDLws/XcTlfG3niszebi
ldJHnLp4lOJHBby0XtYjyQTyfBnJUYzTfau6DfqpjhZa0ljUHCrbPjvjrp+mqblL
LNmwlK3dzc9dTo925v3R6R+v6Zn5o2Fe9SrQIdNSBCVbJYLDIRK6qhRrI1fJaBwn
rNjf6Bwlt5XJFR8hw9MYUmUQH6bBIhhQGbDKJwnGPaqTDCMXUcRj9KC0HEpOAiJU
h2xROVs8dlnBSyKq/QTlVP2b8AHPNHt4p4HkmIuJFkEJHrnv0iy86ssKROt2dO4=
=j9kb
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm"
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: search the best compatible match first in __of_match_node()
Revert "OF: base: match each node compatible against all given matches first"
When an error occurs in the port initialization loop, currently the
driver tries to cleanup all the ports. This results in a NULL pointer
dereference if the ports were only partially initialized.
Fix this by updating only the number of initialized ports (either
with failure or successfully), before jumping to the error path
and looping over that number in the cleanup loop.
Cc: Andrew Lunn <andrew@lunn.ch>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
Pull i2c fixes from Wolfram Sang:
"i2c has a bugfix and documentation improvements for you"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Documentation: i2c: mention ACPI method for instantiating devices
Documentation: i2c: describe devicetree method for instantiating devices
i2c: mv64xxx: refactor message start to ensure proper initialization
Pull timer fixes from Thomas Gleixner:
"The following trilogy of patches brings you:
- fix for a long standing math overflow issue with HZ < 60
- an onliner fix for a corner case in the dreaded tick broadcast
mechanism affecting a certain range of AMD machines which are
infested with the infamous automagic C1E power control misfeature
- a fix for one of the ARM platforms which allows the kernel to
proceed and boot instead of stupidly panicing for no good reason.
The patch is slightly larger than necessary, but it's less ugly
than the alternative 5 liner"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Clear broadcast pending bit when switching to oneshot
clocksource: Kona: Print warning rather than panic
time: Fix overflow when HZ is smaller than 60
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=DDj5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
After recent ACPI core changes acpi_bus_get_device() will always
succeed for dock station ACPI device objects, so show_docked()
should not use that function's return value as an indicator of
whether or not the dock device is present.
Make it use acpi_device_enumerated() for this purpose.
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is a bunch of USB fixes for 3.14-rc3. Most of these are xhci
reverts, fixing a bunch of reported issues with USB 3 host controller
issues that loads of people have been hitting (with the exception of
kernel developers, all of our machines seem to be working fine, which is
why these took so long to get resolved...)
There are some other minor fixes and new device ids, as ususal. All
have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+iUYACgkQMUfUDdst+yl+cACeI7OnpRFgZEAS1yJOGQv0mi/m
uAEAnAw6tNMgMt+W93eIIEtw9b/dOAp2
=nQo7
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.14-rc3. Most of these are xhci
reverts, fixing a bunch of reported issues with USB 3 host controller
issues that loads of people have been hitting (with the exception of
kernel developers, all of our machines seem to be working fine, which
is why these took so long to get resolved...)
There are some other minor fixes and new device ids, as ususal. All
have been in linux-next successfully"
* tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: option: blacklist ZTE MF667 net interface
Revert "usb: xhci: Link TRB must not occur within a USB payload burst"
Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"
Revert "xhci: Set scatter-gather limit to avoid failed block writes."
xhci 1.0: Limit arbitrarily-aligned scatter gather.
Modpost: fixed USB alias generation for ranges including 0x9 and 0xA
usb: core: Fix potential memory leak adding dyn USBdevice IDs
USB: ftdi_sio: add Tagsys RFID Reader IDs
usb: qcserial: add Netgear Aircard 340U
usb-storage: enable multi-LUN scanning when needed
USB: simple: add Dynastream ANT USB-m Stick device support
usb-storage: add unusual-devs entry for BlackBerry 9000
usb-storage: restrict bcdDevice range for Super Top in Cypress ATACB
usb: phy: move some error messages to debug
usb: ftdi_sio: add Mindstorms EV3 console adapter
usb: dwc2: fix memory corruption in dwc2 driver
usb: dwc2: fix role switch breakage
usb: dwc2: bail out early when booting with "nousb"
Revert "xhci: replace xhci_read_64() with readq()"
Revert "xhci: replace xhci_write_64() with writeq()"
...
Here are a small number of tty/serial driver fixes to resolve reported
issues with 3.14-rc and earlier (in the case of the vt bugfix.) Some of
these have been tested and reported by a number of people as the tty
bugfix was pretty commonly hit on some platforms.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+iJAACgkQMUfUDdst+ynLeACfcDynM0/zoSAvfscALTpF796A
KU8AnRyiac0BauTLDmryJSr6pJqkAzMM
=6iYo
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a small number of tty/serial driver fixes to resolve reported
issues with 3.14-rc and earlier (in the case of the vt bugfix). Some
of these have been tested and reported by a number of people as the
tty bugfix was pretty commonly hit on some platforms.
All have been in linux-next for a while"
* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix secure clear screen
serial: 8250: Support XR17V35x fraction divisor
n_tty: Fix stale echo output
serial: sirf: fix kernel panic caused by unpaired spinlock
serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
serial: omap: fix rs485 probe on defered pinctrl
serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
serial: omap-serial: Move info message to probe function
tty: Set correct tty name in 'active' sysfs attribute
tty: n_gsm: Fix for modems with brk in modem status control
drivers/tty/hvc: don't use module_init in non-modular hyp. console code
Here are a number (lots, I know) of fixes for staging drivers to resolve
a bunch of reported issues.
The largest patches here is one revert of a patch that is in 3.14-rc1 to
fix reported problems, and a sync of a usb host driver that required
some ARM patches to go in before it could be accepted (which is why it
missed -rc1).
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+h+MACgkQMUfUDdst+ymAigCeNfR2pmw6lcNLokbdUJDOBHhX
tXwAoL4rzSeaRCu1hbTe0q7lXiZDM+yN
=aMFY
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number (lots, I know) of fixes for staging drivers to
resolve a bunch of reported issues.
The largest patches here is one revert of a patch that is in 3.14-rc1
to fix reported problems, and a sync of a usb host driver that
required some ARM patches to go in before it could be accepted (which
is why it missed -rc1)
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (56 commits)
staging/rtl8821ae: fix build, depends on MAC80211
iio: max1363: Use devm_regulator_get_optional for optional regulator
iio:accel:bma180: Use modifier instead of index in channel specification
iio: adis16400: Set timestamp as the last element in chan_spec
iio: ak8975: Fix calculation formula for convert micro tesla to gauss unit
staging:iio:ad799x fix typo in ad799x_events[]
iio: mxs-lradc: remove useless scale_available files
iio: mxs-lradc: fix buffer overflow
iio:magnetometer:mag3110: Fix output of decimal digits in show_int_plus_micros()
iio:magnetometer:mag3110: Report busy in _read_raw() / write_raw() when buffer is enabled
wlags49_h2: Fix overflow in wireless_set_essid()
xlr_net: Fix missing trivial allocation check
staging: r8188eu: overflow in rtw_p2p_get_go_device_address()
staging: r8188eu: array overflow in rtw_mp_ioctl_hdl()
staging: r8188eu: Fix typo in USB_DEVICE list
usbip/userspace/libsrc/names.c: memory leak
gpu: ion: dereferencing an ERR_PTR
staging: comedi: usbduxsigma: fix unaligned dereferences
staging: comedi: fix too early cleanup in comedi_auto_config()
staging: android: ion: dummy: fix an error code
...
Here is a single driver core patch for 3.14-rc3 for the component code that
Russell has found and fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hoYACgkQMUfUDdst+yn7wgCgslZXCrrhndQEl8A3oCBbfuWj
KgEAoMDMoPyuoCGyQaScQwQoEjYfHMba
=A+dt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core patch for 3.14-rc3 for the component code
that Russell has found and fixed"
* tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: fix devres handling for master device
Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hvIACgkQMUfUDdst+ykGRQCgpi/LgypVecwQlv73TsHLNZo/
ybIAniXJlLgf4xu3q0J+8br3iQ7sg8pC
=m+up
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues"
* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "misc: eeprom: sunxi: Add new compatibles"
Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
misc: mic: fix possible signed underflow (undefined behavior) in userspace API
ARM: sunxi: dt: Convert to the new SID compatibles
misc: eeprom: sunxi: Add new compatibles
misc: genwqe: Fix potential memory leak when pinning memory
Documentation:Update Documentation/zh_CN/arm64/memory.txt
Documentation:Update Documentation/zh_CN/arm64/booting.txt
Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
raw: set range for MAX_RAW_DEVS
raw: test against runtime value of max_raw_minors
Drivers: hv: vmbus: Don't timeout during the initial connection with host
Drivers: hv: vmbus: Specify the target CPU that should receive notification
VME: Correct read/write alignment algorithm
mei: don't unset read cb ptr on reset
mei: clear write cb from waiting list on reset
Commit 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.
Fixes: 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
drivers/net/bonding/bond_options.c includes rwlock.h directly,
which is a nono, and which also breaks RT kernel build.
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fdade4 ("net: of_mdio: parse "max-speed" property to set PHY
supported features") introduced a typo in of_set_phy_supported for the
first assignment of phydev->supported which will not effectively limit
the PHY device supported features bits if the PHY driver contains
"higher" features (e.g: max-speed = <100> and PHY driver has
PHY_GBIT_FEATURES set).
Fix this by making sure that the very first thing is to reset to sane
defaults (PHY_BASIC_FEATURES) and then progressively add speed features
as we parse them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
both tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=J3I5
-----END PGP SIGNATURE-----
Merge tag 'md/3.14-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Two bugfixes for md
both tagged for -stable"
* tag 'md/3.14-fixes' of git://neil.brown.name/md:
md/raid5: Fix CPU hotplug callback registration
md/raid1: restore ability for check and repair to fix read errors.
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 105353145e.
Stephen Chivers reported this is broken as we will get a match
entry '.type = "serial"' instead of the '.compatible = "ns16550"'
in the following scenario:
serial0: serial@4500 {
compatible = "fsl,ns16550", "ns16550";
}
struct of_device_id of_platform_serial_table[] = {
{ .compatible = "ns8250", .data = (void *)PORT_8250, },
{ .compatible = "ns16450", .data = (void *)PORT_16450, },
{ .compatible = "ns16550a", .data = (void *)PORT_16550A, },
{ .compatible = "ns16550", .data = (void *)PORT_16550, },
{ .compatible = "ns16750", .data = (void *)PORT_16750, },
{ .compatible = "ns16850", .data = (void *)PORT_16850, },
...
{ .type = "serial", .data = (void *)PORT_UNKNOWN, },
{ /* end of list */ },
};
So just revert this patch, we will use another implementation to find
the best compatible match in a follow-on patch.
Reported-by: Stephen N Chivers <schivers@csc.com.au>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit f0de8e04a7, it is
incorrect, a future patch will fix this up properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix for a recent regression in the intel_pstate driver that
introduced a race condition causing systems to crash during
initialization in some situations. This removes the affected
code altogether. From Dirk Brandewie.
- ACPIPHP fix for a regression introduced during the 3.12 cycle
causing devices to be dropped as a result of bus check notifications
after system resume on some systems due to the way ACPIPHP interprets
_STA return values (arguably incorrectly). From Mika Westerberg.
- ACPI dock driver fix for a problem causing docking to fail due to
a check that always fails after recent ACPI core changes (found by
code inspection).
- ACPI container driver fix to prevent memory from being leaked in
an error code path after device_register() failures.
- Update of the arm_big_little cpufreq driver maintainer's e-mail
address.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fdRt
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent intel_pstate regression, a fix for a
regression in the ACPI-based PCI hotplug (ACPIPHP) code introduced
during the 3.12 cycle, fixes for two bugs in the ACPI core introduced
recently and a MAINTAINERS update related to cpufreq.
Specifics:
- Fix for a recent regression in the intel_pstate driver that
introduced a race condition causing systems to crash during
initialization in some situations. This removes the affected code
altogether. From Dirk Brandewie.
- ACPIPHP fix for a regression introduced during the 3.12 cycle
causing devices to be dropped as a result of bus check
notifications after system resume on some systems due to the way
ACPIPHP interprets _STA return values (arguably incorrectly). From
Mika Westerberg.
- ACPI dock driver fix for a problem causing docking to fail due to a
check that always fails after recent ACPI core changes (found by
code inspection).
- ACPI container driver fix to prevent memory from being leaked in an
error code path after device_register() failures.
- Update of the arm_big_little cpufreq driver maintainer's e-mail
address"
* tag 'pm+acpi-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
MAINTAINERS / cpufreq: update Sudeep's email address
intel_pstate: Remove energy reporting from pstate_sample tracepoint
ACPI / container: Fix error code path in container_device_attach()
ACPI / hotplug / PCI: Relax the checking of _STA return values
ACPI / dock: Use acpi_device_enumerated() to check if dock is present
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=0lW4
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixes from Borislav Petkov:
"Fix polling timeout setting through sysfs.
You're surely wondering why the patches are not based on an rc. Well,
Andrew sent you 79040cad3f ("drivers/edac/edac_mc_sysfs.c: poll
timeout cannot be zero sent you") already (it got in in -rc2) but it
is not enough as a fix because for one, setting too low polling
intervals (< 1sec) don't make any sense and cause unnecessary polling
load on the system.
Then, even if we set some interval, we explode with
[ 4143.094342] WARNING: CPU: 1 PID: 0 at kernel/workqueue.c:1393 __queue_work+0x1d7/0x340()
because the workqueue setup path is used also for the timeout period
resetting and we're doing INIT_DELAYED_WORK() on an already active
workqueue. Which is total bollocks. So this is taken care of by the
second patch.
I've CCed stable for those two"
* tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Correct workqueue setup path
EDAC: Poll timeout cannot be zero, p2
Pull block IO fixes from Jens Axboe:
"Second round of updates and fixes for 3.14-rc2. Most of this stuff
has been queued up for a while. The notable exception is the blk-mq
changes, which are naturally a bit more in flux still.
The pull request contains:
- Two bug fixes for the new immutable vecs, causing crashes with raid
or swap. From Kent.
- Various blk-mq tweaks and fixes from Christoph. A fix for
integrity bio's from Nic.
- A few bcache fixes from Kent and Darrick Wong.
- xen-blk{front,back} fixes from David Vrabel, Matt Rushton, Nicolas
Swenson, and Roger Pau Monne.
- Fix for a vec miscount with integrity vectors from Martin.
- Minor annotations or fixes from Masanari Iida and Rashika Kheria.
- Tweak to null_blk to do more normal FIFO processing of requests
from Shlomo Pongratz.
- Elevator switching bypass fix from Tejun.
- Softlockup in blkdev_issue_discard() fix when !CONFIG_PREEMPT from
me"
* 'for-linus' of git://git.kernel.dk/linux-block: (31 commits)
block: add cond_resched() to potentially long running ioctl discard loop
xen-blkback: init persistent_purge_work work_struct
blk-mq: pair blk_mq_start_request / blk_mq_requeue_request
blk-mq: dont assume rq->errors is set when returning an error from ->queue_rq
block: Fix cloning of discard/write same bios
block: Fix type mismatch in ssize_t_blk_mq_tag_sysfs_show
blk-mq: rework flush sequencing logic
null_blk: use blk_complete_request and blk_mq_complete_request
virtio_blk: use blk_mq_complete_request
blk-mq: rework I/O completions
fs: Add prototype declaration to appropriate header file include/linux/bio.h
fs: Mark function as static in fs/bio-integrity.c
block/null_blk: Fix completion processing from LIFO to FIFO
block: Explicitly handle discard/write same segments
block: Fix nr_vecs for inline integrity vectors
blk-mq: Add bio_integrity setup to blk_mq_make_request
blk-mq: initialize sg_reserved_size
blk-mq: handle dma_drain_size
blk-mq: divert __blk_put_request for MQ ops
blk-mq: support at_head inserations for blk_execute_rq
...
- Fix some rough edges from the "IP addressing for IBoE" merge
- Other misc fixes, mostly to hardware drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OBaI
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull RDMA/InfiniBand fixes from Roland Dreier:
- Fix some rough edges from the "IP addressing for IBoE" merge
- Other misc fixes, mostly to hardware drivers
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (21 commits)
RDMA/ocrdma: Fix load time panic during GID table init
RDMA/ocrdma: Fix traffic class shift
IB/iser: Fix use after free in iser_snd_completion()
IB/iser: Avoid dereferencing iscsi_iser conn object when not bound to iser connection
IB/usnic: Fix smatch endianness error
IB/mlx5: Remove dependency on X86
mlx5: Add include of <linux/slab.h> because of kzalloc()/kfree() use
IB/qib: Add missing serdes init sequence
RDMA/cxgb4: Add missing neigh_release in LE-Workaround path
IB: Report using RoCE IP based gids in port caps
IB/mlx4: Build the port IBoE GID table properly under bonding
IB/mlx4: Do IBoE GID table resets per-port
IB/mlx4: Do IBoE locking earlier when initializing the GID table
IB/mlx4: Move rtnl locking to the right place
IB/mlx4: Make sure GID index 0 is always occupied
IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device
RDMA/amso1100: Fix error return code
RDMA/nes: Fix error return code
IB/mlx5: Don't set "block multicast loopback" capability
IB/mlx5: Fix binary compatibility with libmlx5
...
We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We use "tx_desc" again after we free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a possible NULL pointer dereference in disconnection flow. This
can happen if the target disconnected/rejected the connection request,
e.g before the binding stage between iscsi connection to the transport
connection.
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2
Fix short to int cast for big endian systems.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We're using edac_mc_workq_setup() both on the init path, when
we load an edac driver and when we change the polling period
(edac_mc_reset_delay_period) through /sys/.../edac_mc_poll_msec.
On that second path we don't need to init the workqueue which has been
initialized already.
Thanks to Tejun for workqueue insights.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: <stable@vger.kernel.org>
Sanitize code even more to accept unsigned longs only and to not allow
polling intervals below 1 second as this is unnecessary and doesn't make
much sense anyway for polling errors.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@vger.kernel.org>
Without that patch, a user can't select the imxfb driver when the i.MX25
and/or the i.MX27 device tree board are selected and that no boards that
selects IMX_HAVE_PLATFORM_IMX_FB are compiled in.
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enable S6E8AX0 LCD driver only if LCD_CLASS_DEVICE is a built-in driver.
Else we get the following errors due to missing symbols:
drivers/built-in.o: In function `s6e8ax0_probe':
:(.text+0x51aec): undefined reference to `lcd_device_register'
:(.text+0x51c44): undefined reference to `lcd_device_unregister'
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The ntc thermistor code was doing math whose temporary result might
have overflowed 32-bits. We need some casts in there to make it safe.
In one example I found:
- pullup_uV: 1800000
- result of iio_read_channel_raw: 3226
- 1800000 * 3226 => 0x15a1cbc80
Signed-off-by: Doug Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
phy_init_hw not does a full PHY reset after the driver probe has
finished, so any hw initialization done in the probe will be lost.
Part of the timestamping functionality of the dp83640 is set up in the
probe and with that lost, enabling timestamping will cause a PHY
lockup, requiring a hard reset / power cycle to recover.
This patch moves all the HW initialization in dp83640_probe to
dp83640_config_init.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0cd8f9cc06 ("drivers: net: cpsw:
enable promiscuous mode support")
Enable promiscuous mode support for CPSW.
Introduced a crash on an am335x based board (similiar to am335x-evm).
Reason is buggy end condition in for loop in cpsw_set_promiscious()
for (i = 0; i <= priv->data.slaves; i++)
should be
for (i = 0; i < priv->data.slaves; i++)
Fix this ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost_zerocopy_callback accesses VQ right after it drops a ubuf
reference. In theory, this could race with device removal which waits
on the ubuf kref, and crash on use after free.
Do all accesses within rcu read side critical section, and synchronize
on release.
Since callbacks are always invoked from bh, synchronize_rcu_bh seems
enough and will help release complete a bit faster.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost checked the counter within the refcnt before decrementing. It
really wanted to know that it is the one that has the last reference, as
a way to batch freeing resources a bit more efficiently.
Note: we only let refcount go to 0 on device release.
This works well but we now access the ref counter twice so there's a
race: all users might see a high count and decide to defer freeing
resources.
In the end no one initiates freeing resources until the last reference
is gone (which is on VM shotdown so might happen after a looooong time).
Let's do what we probably should have done straight away:
switch from kref to plain atomic, documenting the
semantics, return the refcount value atomically after decrement,
then use that to avoid the deadlock.
Reported-by: Qin Chuanyu <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %zu for size_t in order to avoid the following build
warning in printks.
drivers/net/usb/sr9800.c: In function 'sr9800_bind'
drivers/net/usb/sr9800.c:826:2: warning: format '%ld' expects argument of type 'long int' but argument 5 has type 'size_t'
[-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's wrong if the device tree doesn't provide a phy-mode property for
the cpsw slaves as it is documented to be required in
Documentation/devicetree/bindings/net/cpsw.txt.
Anyhow it's nice to catch that problem, still more as it used to work
without this property up to commit 388367a5a9 (drivers: net: cpsw: use
cpsw-phy-sel driver to configure phy mode) which is in v3.13-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7SvUACgkQjTAFq1RaXHNKIgCfQ4bisAc/ZZrqfa6R9uXTsb4J
+toAnAs4U0U453IWMutrshb4gaAGrOaG
=IWyw
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.14-20140212' of git://gitorious.org/linux-can/linux-can
linux-can-fixes-for-3.14-20140212
Marc Kleine-Budde says:
====================
this is a pull request with one patch for net/master, for the current release
cycle. Olivier Sobrie noticed and fixed that the kvaser_usb driver doesn't
check the number of channels value from the hardware, which may result in
writing over the bounds of an array in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Research has shown that commit a77fcf8950 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly. For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IBoE code used to reset the GID table did it for all Ethernet
ports of the device. Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table. Change the reset flow to be
per-port.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Updating the GID table under IBoE requires read/write from/to shared
data structures. These data structures are protected with the device
iboe lock. The flows that modify the GID table start from
1. Initializing the GID table
2. NETDEV events
3. INET or INET6 events
This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held. On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.
This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.
Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned. This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The bonding driver take write locks and spin locks that are shared
by the tx path in enslave processing and notification processing,
If the netconsole is in use, the bonding can call printk which puts
us in the netpoll tx path, if the netconsole is attached to the bonding
driver, result in deadlock.
So add protection for these place, by checking the netpoll_block_tx
state, we can defer the sending of the netconsole frames until a later
time using the retransmit feature of netpoll_send_skb that is triggered
on the return code NETDEV_TX_BUSY.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_newlink() doesn't unregister it for us on failure.
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink kind (and iproute2 type option) is actually called
'macvtap', not 'macvlan'.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
