switch to ioremap()
Adrian Bunk:
The order of the hunks in the patch was slightly rearranged due to an
unrelated change in the driver.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't need to keep track of available buffers, it is simpler
to just compute the value (ala e1000). Don't need tes on link up
because should always have available buffers then.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't free transmit buffers until the whole set of transmit descriptors
has been marked as done. Otherwise, we risk freeing a skb before the
whole transmit is done.
This changes the transmit completion handling from incremental to a
two pass algorithm. First pass scans and records the start of the last
done descriptor, second cleans up until that point.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker (CID: 659, 660) spotted this resource leak on
PCI probe error path. Free private data structure if pci_enable_device()
fails.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 58) spotted this duplicated idx != 0
validation for unicast keys in prism2_ioctl_siwencodeext().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 452, 453, 454, 455, 456) spotted this
unlikely read overrun of CIS buffer. Abort if CISTPL_CONFIG or
CISTPL_MANFID would not fit in buffer.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 930) spotted this double free on error path
(allocation failure). Do not free these here since generic error path
will take care of this.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 273) spotted this inconsequent NULL checking
(unconditionally dereferencing directly after checking for NULL
isn't a good idea). Return immediately to avoid this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 59) noted that the call to prism2_hw_reset()
was dead code. Move prism2_hw_reset() call to a place where it is
actually executed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Observed problems when multiple processes request scans and subsequently
scan results. This causes a scan result request to hit card registers
before the scan is complete, returning an incomplete scan list and
possibly making the card very angry. Instead, cache the results of a
wireless scan and serve result requests from the cache, rather than
hitting the hardware for them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number 2312 was used all over the place to refer to the card's
default MTU. Make it a #define and use that everywhere rather than the
number.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the specific device that driver messages are about.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is version 20 of the Wireless Extensions. This is the
completion of the RtNetlink work I started early 2004, it enables the
full Wireless Extension API over RtNetlink.
Few comments on the patch :
o totally driver transparent, no change in drivers needed.
o iwevent were already RtNetlink based since they were created
(around 2.5.7). This adds all the regular SET and GET requests over
RtNetlink, using the exact same mechanism and data format as iwevents.
o This is a Kconfig option, as currently most people have no
need for it. Surprisingly, patch is actually small and well
encapsulated.
o Tested on SMP, attention as been paid to make it 64 bits clean.
o Code do probably too many checks and could be further
optimised, but better safe than sorry.
o RtNetlink based version of the Wireless Tools available on
my web page for people inclined to try out this stuff.
I would also like to thank Alexey Kuznetsov for his helpful
suggestions to make this patch better.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for new chip 5755 which is very similar to 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the tx producer and consumer fields in separate cache lines in
the device structure, similar to the VJ net channel queue structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine two small (56 byte and 320 byte) pci consistent memory
allocations into one allocation. Jeff Garzik suggested to store
the combined size in the bp structure for later use when freeing
the memory.
Use kzalloc() instead of kmalloc() + memset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some link-related problems by doing a coalesce_now after link
change interrupt to flush out the transient link status.
To facilitate this, the host coalesce cmd register value is cached in
the device structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
this fixes coverity bug #912, where skb is freed first,
and dereferenced a few lines later with skb->len.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PHYs should not be powered down in tg3_set_power_state() because
of bugs or other hardware limitations.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5700 and 5701 will not return correct SRAM data when the chip is in
D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device
in D0 before reading SRAM.
Thanks to Thomas Chenault at Dell for noticing this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- undo some Lindent damage by indenting member names
- remove history at top of .c file, this is stored in the kernel
repo changelog (in greater detail, even).
drivers/net/skfp/fplustm.c: In function `enable_formac':
drivers/net/skfp/fplustm.c:552: warning: large integer implicitly truncated to unsigned type
drivers/net/skfp/fplustm.c:555: warning: large integer implicitly truncated to unsigned type
These arguments were changed to `const', so the compiler can now see that it's
doing and outw(..., 0xffffnnnn). Cast the arg to ushort.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All accessor's different methods are now selected with C code and unused
ones statically optimized away at compile time instead of being selected
with #if's and #ifdef's. This has many advantages such as allowing the
compiler to validate the syntax of the whole code, making it cleaner and
easier to understand, and ultimately allowing people to define
configuration symbols in terms of variables if they really want to
dynamically support multiple bus configurations at the same time (with
the unavoidable performance cost).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Boards with multiple PHYs were not being handled properly by the pcnet32
driver. This patch by Thomas Bogendoerfer with changes by me will allow
Allied Telesyn 2700FTX and 2701FTX boards to use either the copper or
the fiber interfaces. It has been tested on ia32 and ppc64 hardware.
Philippe Seewer also tested and improved the patch.
ethtool for pcnet32 already supports multiple phys.
See also bugzilla bug 4219.
Please apply to 2.6.16
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware has additional error trap interrupt bits. I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: Stephen Hemminger <shemminger@osdl.rog>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change default coalescing parameters slightly, and allow wider
range of values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.
Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin. But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.
It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When I/O is non-cache-coherent, we need to ensure that the I/O buffers
we use don't share cache lines with other data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reformat some code to make it easier to read. And whitespace
fixes.
Signed-off-by: Stephen Hemminger <sheminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add mmio barriers at the appropriate places, don't have a platform
that needs them, but this is where the documentation of the patch
says to add them.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup of the part of the code that sets up DMA configuration.
Should cause no real change in operation, just clearer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SysKonnect Genesis and Yukon chip sets have restrictions on the possible
control block area. The memory needs to not cross 4 Gig boundary, and it needs
to be 8 byte aligned. This patch checks and fails to bring the device up
if region is unacceptable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve performance of skge driver by not touching irq mask
register as much. Since the interrupt source auto-masks, the driver
can just leave it disabled until the end of the soft irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup transmit buffers using NAPI. This allows the transmit routine
to leave interrupts enabled, and that improves performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes the needlessly global function tg3_request_irq()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're now starting to have quite a number of places that do skb_pull
followed immediately by an skb_postpull_rcsum. We can merge these two
operations into one function with skb_pull_rcsum. This makes sense
since most pull operations on receive skb's need to update the
checksum.
I've decided to make this out-of-line since it is fairly big and the
fast path where hardware checksums are enabled need to call
csum_partial anyway.
Since this is a brand new function we get to add an extra check on the
len argument. As it is most callers of skb_pull ignore its return
value which essentially means that there is no check on the len
argument.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call from tg3_init_one()->
tg3_init_link_config() to tg3_open() as is the convention for most other
network drivers.
I was getting a panic after a tg3 device failed to initialize due to DMA
failure. The oops pointed to the link watch queue with spinlock debugging
enabled. Without spinlock debugging, the Oops didn't occur.
I suspect that the link event was getting queued but not executed until
after the DMA test had failed and the device was freed. The link event was
then operating on freed memory, which could contain anything. With this
patch applied, the Oops no longer occurs.
[ Based upon feedback from Michael Chan, we move netif_carrier_off()
to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest -mm sbni gives following warning: WARNING:
drivers/net/wan/sbni.o - Section mismatch: reference to \ .init.data:
from .text between 'init_module' (at offset 0x14ef) and \
'cleanup_module'
The warning is caused by init_module() calling a function declared
__init. Declare init_module() __init too to fix warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutexes conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_PARM() is deprecated and is about to go away altogether.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the old __dev_put macro that is just a hold over from pre 2.6
kernel. And turn dev_hold into an inline instead of a macro.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some nvram related cleanup:
1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.
2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support one-shot MSI on 5787.
This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.
Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here goes a patch for supporting TOIM3232 based serial IrDA dongles.
The code is based on the tekram dongle code.
It's been tested with a TOIM3232 based IRWave 320S dongle. It may work
for TOIM4232 dongles, although it's not been tested.
Signed-off-by: David Basden <davidb-irda@rcpt.to>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix-up tg3_get_ringparam() to return the correct parameters.
Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.
Add missing value for tx_max_pending, noticed by Rick Jones.
Update version to 3.51.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts 2 IrDA drivers pci_module_init() calls to
pci_register_driver().
Signed-off-by: Christophe Lucas <clucas@ifrance.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the deprecated sti/cli routines with the corresponding
spin_lock ones.
Signed-off-by: David chosrova <david.chosrova@libertysurf.fr>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply adds support for a variation of the nsc-ircc PC8739x
chipset, found in some IBM Thinkpad laptops.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings the nsc-ircc code to a more up to date power
management scheme, following the current device model.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables PnP support for the nsc-ircc chipset.
Since we can't fetch the chipset cfg_base from the PnP layer, we just use
the PnP information as one more hint when probing the chip.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include <linux/vmalloc.h> so that it compiles properly on all archs.
Update version to 1.4.38.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.37.
Add missing flush_scheduled_work() in bnx2_suspend as noted by Jeff
Garzik.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support bigger rx ring sizes (up to 1020) in the rx fast path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase maximum receive ring size from 255 to 1020 by supporting
up to 4 linked pages of receive descriptors. To accomodate the
higher memory usage, each physical descriptor page is allocated
separately and the software ring that keeps track of the SKBs and the
DMA addresses is allocated using vmalloc.
Some of the receive-related fields in the bp structure are re-
organized a bit for better locality of reference.
The max. was reduced to 1020 from 4080 after discussion with David
Miller.
This patch contains ring init code changes only. This next patch
contains rx data path code changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the rx code path that does not handle the full rx ring correctly.
When the rx ring is set to the max. size (i.e. 255), the consumer and
producer indices will be the same when completing an rx packet. Fix
the rx code to handle this condition properly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some of the registers in ethtool register test to reduce
driver size.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().
Change the power state parameter to pci_power_t type and use
constants defined in pci.h.
Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't read from free'd memory after calling netif_rx(). docopy is used as
a boolean (0 and 1) so unsigned int is sufficient.
Coverity bug #928
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.
For example, some 4-port card or mother board designs have 5704 behind
the 5714.
All devices behind the EPB require the 40-bit DMA workaround.
Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
semaphore to mutexes conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix gcc warning: ipw2100.c:2460: ISO C90 forbids mixed declarations and code
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Andrea Merello <andreamrl at tiscali it>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a big array overun found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies the driver to support the ipw2200-fw-3.0 image format.
The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:
1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)
2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.
Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:
http://ipw2200.sf.net/firmware.php
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: Olivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set a meaningful silence threshold value (replacing our previous "0"
default), which gets rid of the gratuitous "Link deterioration"
notifications that we've been receiving from firmware. This
notification feature tells the driver information to help it determine
when to pre-emptively restart the firmware/ucode in anticipation of
firmware errors! But since setting this new threshold, I haven't seen
any such notifications. At least it keeps the logs a little less busy.
Signed-off-by: Cahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently iwlist ethX freq[uency]/channel lists all the channels the card
supported for the current region, which includes some channels can only
be used in infrastructure mode. This patch filters these channels out if
the card is currently in ad-hoc mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When loading the ipw2200 module with disabled=1, rf_kill is activated after
every mode change. This is caused by ipw_sw_reset() is called when a mode
is changed. The patch fixed the problem by distinguishing the purposes with
the 'option' paramenter.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wpa_supplicant needs to set wpa_enabled unconditionally, with this check
it hasn't been possible to connect to non-WPA networks using wpa_supplicant.
So remove below check.
if (priv->ieee->wpa_enabled &&
network->wpa_ie_len == 0 && network->rsn_ie_len == 0)
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does two things. It uses the parameter IW_QUAL_DBM which is new
in WE-19 to cause signal level and noise to be reported in dBm by the
wireless tools. It also defines the signal level as an unsigned integer
so that the signal level will be reported by iwlist iface scan.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace ipw2200 specific frame_hdr_len() with generic
ieee80211 routine ieee80211_get_hdrlen()
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch roll back the change we made to support for the ability to
start/stop independent Tx queues within a single net device in order to
support 802.11e QoS. We need to be able to indicate to the upper layers
that packets of a given priority can not be sent any more without halting
transmission of all packets, and without rescheduling high priority packets
down to the next priority level.
So we return NETDEV_TX_BUSY in this case and rely on the stack would
take care of rescheduling... which it apparently does immediately and
consumes the CPU. This caused the ksoftirqd kernel thread consuming almost
all the CPU...
To put the code back to the way it was before we made these changes we
put the call netif_queue_stop back in ipw_tx_skb. This effectively
disables multiple priority based transmit queues for 802.11e, but given
that its broken anyway...
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Given the amount of support requests for the meaning of the geography code
I've written a patch for printing this information on module load no matter
the debug level.
I've also added a section to the README.ipw2200 file listing the geography
codes and their meaning.
Signed-off-by: Henrik Brix Andersen <brix@gentoo.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the needlessly global function ipw_qos_current_mode()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As stated in a comment, the ipw2200 driver uses several routines that
were borrowed from ieee80211_geo.c. As ipw2200 requires ieee80211,
these routines are duplicated. The attached patch, which is sent
as an attachment to preserve whitespace, converts ipw2200.c to use
the ieee80211 versions, thereby reducing bloat in both the source
and binary.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spidernet drivers uses request_firmware() and thus needs to select
FW_LOADER.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk wrote:
> The Coverity checker spotted the following two array overflows in
> drivers/net/chelsio/sge.c (in both cases, the arrays contain 3
> elements):
[snip]
This is a bug. The array should contain 2 elements. Here is the fix.
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
return -E_NO_BIG_ENDIAN_TESTING;
[E1000]: Fix 4 missed endianness conversions on RX descriptor fields.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olaf Hering reported a problem on pseries with e100 where ethtool -t would
cause a bus error, and the e100 driver would stop working. Due to the new
load ucode command the cb list must be allocated before calling
e100_init_hw, so remove the call and just let e100_up take care of it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
This patch moves prototypes of global variables and functions to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: John Ronciak <john.ronciak@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker spotted this dead code (note that (clock_ctrl == 7)
is already handled above).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're leaking an skb in a failure path in this function.
Coverity #632
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted these two unused variables.
Please check whether this patch is correct or whether they should be
used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o Make sgiseeq_dump_rings static.
o Delete unused sgiseeq_my_reset.
o Move DEBUG define to beginning where it's easier to spot and will be
seen by <linux/kernel.h> as well.
o Use NULL for pointer initialization.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert 3c509 driver to use proper suspend/resume API instead of the
deprecated pm_register/pm_unregister.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In latest -mm de620 gave following warning:
WARNING: drivers/net/de620.o - Section mismatch: reference to \
.init.text:de620_probe from .text between 'init_module' (at offset \
0x1682) and 'cleanup_module'
init_module() call de620_probe() which is declared __init.
Fix is to declare init_module() __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve reference to PCI NE2K support in ISA NE2K documentation.
Original 2.4 patch From: Ged Haywood <ged@jubileegroup.co.uk>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes an error in the dl2k driver's DMA mapping/unmapping.
The adapter uses the upper 16bits of the DMA address for the buffer
size. However, this is not masked off when referencing the DMA
address, and can lead to errors by trying to free a DMA address out of
range.
Thanks,
Jon
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For some reason, E1000's ->hard_start_xmit() routine returns -EFAULT
instead of one of the NETDEV_TX_* error codes. In fact, it frees up
the SKB before returning this. This makes the queueing layer think
the packet should be requeued and subsequently we corrupt a freed
object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turn on truncation to prevent getting choked by frames larger than expected.
Without this fix, driver hangs after receiving an oversize packet.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Avoid premature transmit ring full conditions.
Force a transmit status interrupt if transmit ring gets nearly full
and after a TSO send.
Allow more entries in transmit ring to be used if dma_addr is 32 bits
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Don't use sky2 to seed random pool beacause the network packet arrival time
will not be truly random due to NAPI and interrupt mitigation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
de_init_hw enables the irq thus it must be issued after request_irq.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Paul Rolland reported that e1000 was having a hard time using mii-tool to set speed and duplex. This patch fixes the issue on both newer hardware as well as fixing the code issue that originally caused the problem.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add DMA workaround for chips that do not support full 64-bit DMA
addresses.
5714, 5715, and 5780 chips only support DMA addresses less than 40
bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so
that pci_map_xxx() calls will map the DMA address below 40 bits if
necessary. On 64-bit systems without IOMMU, set the dma_mask to
64-bit and check for DMA addresses exceeding the limit in
tg3_start_xmit().
5788 only supports 32-bit DMA so need to set the mask appropriately
also.
Thanks to Chris Elmquist at SGI for reporting and helping to debug
the problem on 5714.
Thanks to David Miller for explaining the HIGHMEM and DMA stuff.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checking e100.c code against Documentation/io_ordering.txt I found the
following problem:
spin_lock_irq...
write
spin-unlock
e100_write_flush
The attached patch fix the code like this:
spin_lock_irq...
write
e100_write_flush
spin-unlock
Signed-off-by: Catalin BOIE <catab@umbrella.ro>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As documented in National application note 1287 the RX state machine on
the natsemi chip can lock up under some conditions (mostly related to
heavy load). When this happens a series of bogus packets are reported
by the chip including some oversized frames prior to the final lockup.
This patch implements the fix from the application note: when an
oversized packet is reported it resets the RX state machine, dropping
any currently pending packets.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts the natsemi driver to use NAPI. It was originally
based on one written by Harald Welte, though it has since been modified
quite a bit, most extensively in order to remove the ability to disable
NAPI since none of the other drivers seem to provide that functionality
any more.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the 4th port and other new features of the
BCM1480 SOC.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the BIT0-BIT31 defines are no longer used by mv643xx_eth.c,
remove them from mv643xx_eth.h.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The task level rx queue refill feature hasn't ever worked
(at least in 2.6) and is of dubious value. Remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify and remove redundant code for filling transmit descriptors.
No changes in features; it's just a code reorganization/cleanup.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>From : Dale Farnsworth <dale@farnsworth.org>
Recent patches for the mv643xx_eth driver now use the MII interface
library. Select MII so it gets built when that driver is selected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use better terminology for HW queues. No functional changes.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- this implementation of prefetch was tested on new and old hardware
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Add restriction for ESB2 to MTU size <=9216
- Removed FIFO errors which were not being used
- Fixed issues with loopback
- Power management change for saving state and config space
- WA to disable recieves and reset device on link loss. Reset needed to be done outside the interrupt context - modified existing tx_timeout_task
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
- Simplified by calling skb_fill_page_desc(), which is more efficient.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
The axnet_cs driver can support the AMB8110 PC Card, so add the id for it.
In the old pcmcia-cs config file, this card is listed with the comment "not
specific enough". The last entry in the axnet_ids has the same comment.
They are disabled, and for good reason as it was originally identified by
the MANFID, and that is shared with several cards that use both the
pcnet_cs driver and axnet_cs driver. I tried my AMB8110 with pcnet_cs, and
found that it works fine, and I cannot find a reason for either, except
that the old config file recommended axnet_cs.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't just use cards with PCMCIA ID 0x0156, 0x0002. Make sure that the
vendor string is "Intersil" or "INTERSIL"
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A recent patch attempted to enable more efficient memory usage by using
only 2kB descriptors for jumbo frames. The method used to implement this
has since been commented upon as "illegal" and in recent kernels even
causes a BUG when receiving ip fragments while using jumbo frames.
This patch simply goes back to the way things were. We expect some
complaints due to order 3 allocations failing to come back due to this
change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.
In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These messages end up polluting logs when things like NetworkManager or
wpa_supplicant are controlling the driver. They aren't really that
useful, and no other drivers output messages like this when the user
fiddles with encryption keys. Users can use iwconfig and other
wireless-tools methods to determine and change the current transmit key
if they wish to do so manually. Therefore, remove the messages.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- check that the device is up before it is enabled again;
- the descriptor ring indexes must be set to zero before
cp_init_hw() is issued. Add a nice comment to remember
that skb allocation failure is still not handled.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5681
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
velocity_rx_refill() only replenishes the descriptor entries which
belong to the CPU. It works great in the Rx path but the driver must
ensure that all the descriptors are freed before velocity_rx_refill()
is used in velocity_change_mtu(). The patch resets the Rx descriptors
in velocity_free_rd_ring().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem
vendor ID. So add another fallback test, which is the name
of the OBP firmware device tree node. If it's a Sun part we'll
get "network", else it will be named "ethernet".
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs in the WoL implementation of sis900. The first causes
hangs on some system on driver load, the second causes troubles
when disabling WoL support. Both fixes are one liner and really
simple.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Daniele Venzano <venza@brownhat.org>
drivers/net/tlan.c compiles with CONFIG_PCI=n only with a warning and
due to the dead code elimination of gcc.
Additionally, this fixes the only compile error I found with
CONFIG_PCI=n and the gcc -Werror-implicit-function-declaration
flag on i386.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The most usable number of ifb devices is 2. Change the default to 2.
Signed-off-by: Richard Lucassen <spamtrap@lucassen.org>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The SysKonnect Genesis based board would fail on initialization
with phy_read errors caused by not waiting for last phy write.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Fix a race in the receive NAPI, irq handling. The interrupt clear and the
start need to be separated. Otherwise there is a window between the last
frame received and the NAPI done level handling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
rtl8169_hw_start() requires that the descriptor ring indexes be
set to zero. Let a deferred invocation of rtl8169_reset_task()
handle it. Enabling a few power management bits will not hurt
either.
suspend/resume is issued with irq on: the spinlock do not need
to save the irq flag.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Need to avoid race in updating IRQ mask. This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.
I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to force a transmit coalesce timer restart after processing
transmit packets. Otherwise, can get transmit status after last
update and chip doesn't send the next one.
Can go with the chip defaults for coalescing timers, except for
Tx timer which needs to be bigger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to restart the interrupt coalescing timer after clearing the interrupt,
to avoid races with interrupt timer and processing.
Patch from Carl-Daniel Halfinger
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Don't allow coalescing values to be bigger than the transmit ring.
Since if you set them that big, the interrupt never happens and driver
livelocks.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The following message will be only printed if DEBUG_NOTIF is on. "Unknown
notification: subtype=40,flags=0xa0,size=40"
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This forcedeth patch adds support for MSI/MSIX interrupts.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This forcedeth patch adds high dma support for tx/rx rings.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This forcedeth patch adds support for vlan stripping/inserting in hardware.
Signed-off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes 2 bugs in the USB-IrDA code.
The first one is a buffer overrun in the RX path. We are now using
IRDA_SKB_MAX_MTU when initializing the Rx URB.
The second one is a potential stack recursion when unplugging the USB
dongle. It seems that first we get the Rx URB with a generic error
code, and after a while the Rx URB comes again with a "disconnect"
error code. Since we are resubmitting the Rx URB immediately after
receiving the first error one, we might enter an endless loop.
When getting an error Rx URB, the patch defers the Rx URB resubmitting
so that it gives us a chance to catch the disconnect one, in case the
dongle has juts been unplugged.
Tested against 2.6.16-rc2.
Patch from Jean Tourrilhes
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_release returns EINVAL without releasing the bond lock if the
slave device is not being bonded by the bond. The following patch
ensures that the lock is released in this case.
Signed-off-by: Stephen J. Bevan <stephen@dino.dnsalias.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/tokenring/smctr.c: In function `smctr_load_firmware':
drivers/net/tokenring/smctr.c:2981: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Users report problems w/ auto-negotiation disabled and the link set
to 100/Half or 10/Half. Problems range from poor performance to no
link at all.
The current sky2 code does not set things properly on link up if
autonegotiation is disabled. Plus it does not contemplate a 10Mbit
setting at all. This patch corrects that.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is a clone of John Linville's fixed for speed setting on sky2 driver.
The skge driver has the same code (and bug). It would not allow manually forcing
100 and 10 mbit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Take the experimental dependency of skge driver, it is as stable as the
others.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver was changed a while ago to remove support for the
D-Link 530T card because that hardware has no working VPD data. The help
text for Kconfig was not updated.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some bitfields were incorrectly initialised in wavelan_cs,
causing some compiler warning. Also killed a error message that should
not be there...
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The previous patch that added ENCODEEXT and AUTH support to the airo
driver contained a slight error which would cause setting the TX
key index ignore a valid key-set request at the same time. This patch
allows any combination of setting the TX key index and setting an
encryption key.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We didn't set the WEP key to hardware when we are using software based
crypto. Hardware needs the key to do WEP authentication even for
software based encryption.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects a few spelling and grammar errors found in
drivers/net
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not avoid APs with wpa_ie or rsn_ie if !ieee->wpa_enabled
There are broken APs out there that fill these elements even
though encryption is disnabled. Also, this breaks legit WEP to
WPA migration scenarious.
We add a checking to prohibite WPA configured STA trying to
associate with non-WPA supported APs.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I have made a stupid copy&paste error: QoS option is named IPW_QOS not
IPW2200_MONITOR. Spotted by Daniel Paschka, thanks.
Add the following config entries for the ipw2200 driver to
drivers/net/wireless/Kconfig
* IPW2200_MONITOR
enables Monitor mode
* IPW_QOS
enables QoS feature - this is under development right now, so it depends
upon EXPERIMENTAL
Signed-off-by: Andreas Happe <andreashappe@snikt.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the Atmel driver-only IEEE 802.11 constants to their
equivalents from the kernel's ieee80211 layer headers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the IPW2100 and IPW2200 options available in
the configuration menu even if IEEE80211 has not been selected before.
This behaviour is more intuitive for people which are not familiar with
the driver internals.
The suggestion for this change was made by Alejandro Bonilla Beeche.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a number of bugs in the authentication process:
1) When falling back to Shared Key authentication mode from Open System,
a missing 'return' would cause the auth request to be sent, but would
drop the card into Management Error state. When falling back, the
driver should also indicate that it is switching to Shared Key mode by
setting exclude_unencrypted.
2) Initial authentication modes were apparently wrong in some cases,
causing the driver to attempt Shared Key authentication mode when in
fact the access point didn't support that mode or even had WEP disabled.
The driver should set the correct initial authentication mode based on
wep_is_on and exclude_unencrypted.
3) Authentication response packets from the access point in Open System
mode were getting ignored because the driver was expecting the sequence
number of a Shared Key mode response. The patch separates the OS and SK
mode handling to provide the correct behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch that added ENCODEEXT and AUTH support to the atmel
driver contained a slight error which would cause just setting the TX
key index to also set the encryption key again. This patch allows any
combination of setting the TX key index and setting an encryption key.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Below this point, the error path will proceed through
sis190_release_board(). It will happily oops if
pci_set_drvdata() has not been issued.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
drivers/net/appletalk/cops.c: In function `cops_load':
drivers/net/appletalk/cops.c:539: warning: assignment discards qualifiers from pointer target type
drivers/net/appletalk/cops.c:547: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orinoco wireless driver can support the SMC 2532W-B PC Card, so add the
id for it.
Signed-off-by: Jesse Allen <the3dfxdude@gmail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Firmware should go into /lib/firmware, not /etc/firmware.
Found by Alejandro Bonilla.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make the whole netdevices menu depend on NET, rather than having an empty
submenu when networking is disabled.
Indeed, almost the whole body of the menu was surrounded by if NETDEVICES,
and what was outside depended on NETCONSOLE which is inside the menu.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/tulip/uli526x.c: In function `__check_mode':
drivers/net/tulip/uli526x.c:1693: warning: return from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/s2io.c: In function `verify_l3_l4_lro_capable':
drivers/net/s2io.c:6638: warning: ISO C90 forbids mixed declarations and code
Cc: Ravinandan Arakali <Ravinandan.Arakali@neterion.com>
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix this:
drivers/built-in.o(.text+0x89469): In function `s2io_get_ethtool_stats':
drivers/net/s2io.c:5209: undefined reference to `__udivdi3'
Cc: Ravinandan Arakali <Ravinandan.Arakali@neterion.com>
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It returns a pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/bonding/bond_sysfs.c:263:27: warning: Using plain integer as NULL pointer
drivers/net/bonding/bond_sysfs.c:998:26: warning: Using plain integer as NULL pointer
drivers/net/bonding/bond_sysfs.c:1126:26: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add NETIF_F_TSO (NETIF_F_UFO) to BOND_INTERSECT_FEATURES so that it can
be used by a bonding device iff all its slave devices support TSO (UFO).
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Increase version, and get rid of out-dated comment.
Speed setting has worked for quite a while.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This hardware supports Message Signaled interrupts.
When setting up, use software interrupt to check for bad hardware.
Signed-off-by: Stephen Hemminger <shemminger @osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Move the interrupt clear to before processing, this avoids a
possible races with status delaying.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>