315 lines
6.9 KiB
C++
315 lines
6.9 KiB
C++
/* H-bridge defines */
|
|
#define PWM1M1 5
|
|
#define PWM2M1 6
|
|
/* Limits for control signal */
|
|
#define outMax 255
|
|
#define outMin 0
|
|
/* Encoder defines */
|
|
#define SELECT_PIN 7
|
|
#define CLOCK_PIN 8
|
|
#define DATA_PIN 9
|
|
/* Ratio of worm gear */
|
|
#define RATIO 30
|
|
/* Maximum Angle for homing scanning */
|
|
#define MAX_AZ_ANGLE 370
|
|
/* Homing switch */
|
|
#define HOME_AZ 2
|
|
/* Change to LOW according to Home sensor */
|
|
#define DEFAULT_HOME_STATE HIGH
|
|
/* Time to disable the motors in millisecond */
|
|
#define T_DELAY 60000
|
|
/* PIN for Enable or Disable Stepper Motors */
|
|
#define EN 4
|
|
/* Serial configuration */
|
|
#define BufferSize 256
|
|
#define BaudRate 19200
|
|
/*Global Variables*/
|
|
unsigned long t_DIS = 0; /*time to disable the Motors*/
|
|
/* angle offset */
|
|
double az_angle_offset = 0;
|
|
|
|
void setup()
|
|
{
|
|
/* H-bridge */
|
|
pinMode(OUTPUT, PWM1M1);
|
|
pinMode(OUTPUT, PWM2M1);
|
|
/* Encoder */
|
|
pinMode(DATA_PIN, INPUT);
|
|
pinMode(CLOCK_PIN, OUTPUT);
|
|
pinMode(SELECT_PIN, OUTPUT);
|
|
digitalWrite(CLOCK_PIN, HIGH);
|
|
digitalWrite(SELECT_PIN, HIGH);
|
|
/* Homing switch */
|
|
pinMode(HOME_AZ, INPUT_PULLUP);
|
|
/* Serial Communication */
|
|
Serial.begin(BaudRate);
|
|
/* Initial Homing */
|
|
Homing(-MAX_AZ_ANGLE, true);
|
|
/* Enable Motors */
|
|
pinMode(EN, OUTPUT);
|
|
digitalWrite(EN, HIGH);
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
static double AZangle = 0;
|
|
|
|
/* Read commands from serial */
|
|
cmd_proc(AZangle);
|
|
/* Move Motor */
|
|
dc_move(AZangle);
|
|
}
|
|
|
|
/* EasyComm 2 Protocol */
|
|
void cmd_proc(double &angleAz)
|
|
{
|
|
/* Serial */
|
|
char buffer[BufferSize];
|
|
char incomingByte;
|
|
char *Data = buffer;
|
|
char *rawData;
|
|
static int BufferCnt = 0;
|
|
char data[100];
|
|
/* Read from serial */
|
|
while (Serial.available() > 0)
|
|
{
|
|
incomingByte = Serial.read();
|
|
/* New data */
|
|
if (incomingByte == '\n')
|
|
{
|
|
buffer[BufferCnt] = 0;
|
|
if (buffer[0] == 'A' && buffer[1] == 'Z')
|
|
{
|
|
if (buffer[2] == ' ' && buffer[3] == 'E' && buffer[4] == 'L')
|
|
{
|
|
/* Get position */
|
|
Serial.print("AZ");
|
|
Serial.print(getposition(), 1);
|
|
Serial.print(" ");
|
|
Serial.print("EL");
|
|
Serial.println(0, 1);
|
|
Serial.println(az_angle_offset);
|
|
}
|
|
else
|
|
{
|
|
/* Get the absolute value of angle */
|
|
rawData = strtok_r(Data, " " , &Data);
|
|
strncpy(data, rawData+2, 10);
|
|
if (isNumber(data))
|
|
angleAz = atof(data);
|
|
/* Get the absolute value of angle */
|
|
rawData = strtok_r(Data, " " , &Data);
|
|
if (rawData[0] == 'E' && rawData[1] == 'L')
|
|
{
|
|
strncpy(data, rawData+2, 10);
|
|
if (isNumber(data))
|
|
;
|
|
}
|
|
}
|
|
}
|
|
/* Stop Moving */
|
|
else if (buffer[0] == 'S' && buffer[1] == 'A' && buffer[2] == ' ' && buffer[3] == 'S' && buffer[4] == 'E')
|
|
{
|
|
angleAz = getposition();
|
|
/* Get position */
|
|
Serial.print("AZ");
|
|
Serial.print(getposition(), 1);
|
|
Serial.print(" ");
|
|
Serial.print("EL");
|
|
Serial.println(0, 1);
|
|
}
|
|
/* Reset the rotator */
|
|
else if (buffer[0] == 'R' && buffer[1] == 'E' && buffer[2] == 'S' && buffer[3] == 'E' && buffer[4] == 'T')
|
|
{
|
|
/* Get position */
|
|
Serial.print("AZ");
|
|
Serial.print(getposition(), 1);
|
|
Serial.print(" ");
|
|
Serial.print("EL");
|
|
Serial.println(0, 1);
|
|
/* Move to initial position */
|
|
Homing(-MAX_AZ_ANGLE, false);
|
|
angleAz = 0;
|
|
}
|
|
BufferCnt = 0;
|
|
}
|
|
/* Fill the buffer with incoming data */
|
|
else {
|
|
buffer[BufferCnt] = incomingByte;
|
|
BufferCnt++;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Homing Function */
|
|
void Homing(double AZangle, bool Init)
|
|
{
|
|
int value_Home_AZ = DEFAULT_HOME_STATE;
|
|
boolean isHome_AZ = false;
|
|
double az_zero_angle = getposition();
|
|
|
|
while(isHome_AZ == false )
|
|
{
|
|
dc_move(AZangle);
|
|
value_Home_AZ = digitalRead(HOME_AZ);
|
|
/* Change to LOW according to Home sensor */
|
|
if (value_Home_AZ == DEFAULT_HOME_STATE)
|
|
{
|
|
isHome_AZ = true;
|
|
if (Init)
|
|
az_angle_offset = getposition();
|
|
}
|
|
if (abs(getposition() - az_zero_angle) > MAX_AZ_ANGLE && !isHome_AZ)
|
|
{
|
|
/* set error */
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
void dc_move(double set_point_az)
|
|
{
|
|
static double u = 0;
|
|
static double angle_az = 0;
|
|
static double prev_angle_az = 0;
|
|
static double error = 0;
|
|
static double Iterm = 0;
|
|
static double Pterm = 0;
|
|
static double Dterm = 0;
|
|
double Kp = 2000;
|
|
double Ki = 1;
|
|
double Kd = 0;
|
|
double dt = 0.001;
|
|
|
|
angle_az = getposition();
|
|
error = set_point_az - angle_az;
|
|
|
|
Pterm = Kp*error;
|
|
|
|
Iterm += Ki*error*dt;
|
|
if(Iterm > outMax) Iterm= outMax;
|
|
else if(Iterm < outMin) Iterm= outMin;
|
|
|
|
Dterm = Kd*(angle_az - prev_angle_az)/dt;
|
|
prev_angle_az = angle_az;
|
|
|
|
u = Pterm+Iterm+Dterm;
|
|
|
|
if (u >= 0)
|
|
{
|
|
if (u > outMax)
|
|
u = outMax;
|
|
analogWrite(PWM1M1, u);
|
|
analogWrite(PWM2M1, 0);
|
|
}
|
|
else
|
|
{
|
|
u = -u;
|
|
if ( u > outMax)
|
|
u = outMax;
|
|
analogWrite(PWM1M1, 0);
|
|
analogWrite(PWM2M1, u);
|
|
}
|
|
}
|
|
|
|
/* get position from encoder */
|
|
double getposition()
|
|
{
|
|
double encoder_pos;
|
|
double delta_pos;
|
|
double real_pos;
|
|
static double prev_pos = 0;
|
|
int raw_pos;
|
|
static int n = 0;
|
|
|
|
raw_pos = readPosition();
|
|
if (raw_pos >= 0)
|
|
{
|
|
encoder_pos = ((float)raw_pos / 1024.0) * 360.0;
|
|
delta_pos = prev_pos - encoder_pos;
|
|
if (delta_pos > 180)
|
|
n++;
|
|
else if (delta_pos < -180)
|
|
n--;
|
|
real_pos = ((encoder_pos + 360*n)/RATIO) - az_angle_offset;
|
|
prev_pos = encoder_pos;
|
|
}
|
|
else
|
|
; /* set error */
|
|
|
|
return real_pos;
|
|
}
|
|
|
|
/* check if is argument in number */
|
|
boolean isNumber(char *input)
|
|
{
|
|
for (int i = 0; input[i] != '\0'; i++)
|
|
{
|
|
if (isalpha(input[i]))
|
|
return false;
|
|
}
|
|
return true;
|
|
}
|
|
|
|
/* Code from http://reprap.org/wiki/Magnetic_Rotary_Encoder_1.0 */
|
|
|
|
/* read the current angular position */
|
|
int readPosition()
|
|
{
|
|
unsigned int position = 0;
|
|
|
|
/* shift in our data */
|
|
digitalWrite(SELECT_PIN, LOW);
|
|
delayMicroseconds(0.5);
|
|
byte d1 = shiftIn(DATA_PIN, CLOCK_PIN);
|
|
byte d2 = shiftIn(DATA_PIN, CLOCK_PIN);
|
|
digitalWrite(SELECT_PIN, HIGH);
|
|
|
|
/* get our position variable */
|
|
position = d1;
|
|
position = position << 8;
|
|
position |= d2;
|
|
|
|
position = position >> 6;
|
|
|
|
/* check the offset compensation flag: 1 == started up */
|
|
if (!(d2 & B00100000))
|
|
position = -1;
|
|
|
|
/* check the cordic overflow flag: 1 = error */
|
|
if (d2 & B00010000)
|
|
position = -2;
|
|
|
|
/* check the linearity alarm: 1 = error */
|
|
if (d2 & B00001000)
|
|
position = -3;
|
|
|
|
/* check the magnet range: 11 = error */
|
|
if ((d2 & B00000110) == B00000110)
|
|
position = -4;
|
|
|
|
return position;
|
|
}
|
|
|
|
/* read in a byte of data from the digital input of the board. */
|
|
byte shiftIn(byte data_pin, byte clock_pin)
|
|
{
|
|
byte data = 0;
|
|
|
|
for (int i=7; i>=0; i--)
|
|
{
|
|
digitalWrite(clock_pin, LOW);
|
|
delayMicroseconds(0.5);
|
|
digitalWrite(clock_pin, HIGH);
|
|
delayMicroseconds(0.5);
|
|
digitalWrite(clock_pin, LOW);
|
|
|
|
byte bit = digitalRead(data_pin);
|
|
data |= (bit << i);
|
|
|
|
}
|
|
|
|
return data;
|
|
}
|
|
|