The MIPI DSI PHY controller on Allwinner A64 is similar
on the one on A31.
Add A64 compatible and append A31 compatible as fallback.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Message-Id: <20191025175625.8011-3-jagan@amarulasolutions.com>
The MIPI DSI controller in Allwinner A64 is similar to A33.
But unlike A33, A64 doesn't have DSI_SCLK gating so it is valid
to have separate compatible for A64 on the same driver.
DSI_SCLK uses mod clock-names on dt-bindings, so the same
is not required for A64.
On that note
- A64 require minimum of 1 clock like the bus clock
- A33 require minimum of 2 clocks like both bus, mod clocks
So, update dt-bindings so-that it can document both A33,
A64 bindings requirements.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Message-Id: <20191025175625.8011-2-jagan@amarulasolutions.com>
This commit adds support for the NewEast Optoelectronics CO., LTD
WJFH116008A 11.6" 1920x1080 TFT LCD panel.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
The ANX6345 is an ultra-low power DisplayPort/eDP transmitter designed
for portable devices.
Add a binding document for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
sun8i-thermal driver supports thermal sensor in wide range of Allwinner
SoCs. Add YAML schema for its bindings.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER]
bit may be falsely set when reading internal PCS registers.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes, a documentation fix, and a removal of a spec
violation for the bus recovery algorithm in the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: fix bus recovery stop mode timing
i2c: bcm2835: Store pointer to bus clock
dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
i2c: at91: fix clk_offset for sam9x60
A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4TMdwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0M5UB/9w0mzrmuaJzctm3Jm8LiCIjJoZ0woQ
chgbhm2C/I6idENxdUhaJ1YZMI6NkmJKpJy5tQ/QH4MnbOVT/vHIEmIsRYO0vYoF
ApERJLia8da1OpiJlPTbsg3eUXVNmPMVeAkq5MgKSflaIjV6Ejc0FRWmgDYvzhu9
xkCsptAF7MYPUuHdBcjXPscSf1/w+FdDy8VYncEluyJ0NpGDU64N/XdTwRmsG8QW
BxA1jPPKi445NsC+OV8SFfNZbeEXG2iSEBPvp4tMGtd0TiIp3UNLTRzMstEFE6SD
hCzL9fQEzUgHD+B0vLmccyy0HR0phk6813jf9KeToAjAxKtf5XhQajW+
=Ad4n
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
SAM9X60 also supports i2c-sda-hold-time-ns. Fix the documentation accordingly.
Fixes: 2034e3f4c9 ("dt-bindings: i2c: at91: add new compatible")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SPI core supports Octal SPI controllers which have 8 IO lines.
Therefore document 8 as a valid option for spi-tx{rx}-bus-width
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200102102118.23318-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
DT property definitions must be under a 'properties' keyword. This was
missing for 'snps,tso' in an if/then clause. A meta-schema fix will
catch future errors like this.
Fixes: 7db3545aef ("dt-bindings: net: stmmac: Convert the binding to a schemas")
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
I didn't get a batch in this weekend, so here's what we queued up last
week and today.
- A couple of defconfigs add back debugfs -- it used to be implicitly
enabled through CONFIG_TRACING, but 0e4a459f56 ("tracing: Remove
unnecessary DEBUG_FS dependency") removed that.
- The rest are mostly minor fixlets of the usual kind; some DT tweaks,
a headerfile refactor that needs a build fix now, etc.
-----BEGIN PGP SIGNATURE-----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=cr5E
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I didn't get a batch in this weekend, so here's what we queued up last
week and today.
- A couple of defconfigs add back debugfs -- it used to be implicitly
enabled through CONFIG_TRACING, but 0e4a459f56 ("tracing:
Remove unnecessary DEBUG_FS dependency") removed that.
- The rest are mostly minor fixlets of the usual kind; some DT
tweaks, a headerfile refactor that needs a build fix now, etc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: bcm: Add missing sentinel to bcm2711_compat[]
ARM: shmobile: defconfig: Restore debugfs support
bus: ti-sysc: Fix missing reset delay handling
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
ARM: mmp: include the correct cputype.h
ARM: dts: am437x-gp/epos-evm: fix panel compatible
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: bcm283x: Fix critical trip point
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
reset: Do not register resource data for missing resets
reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
reset: brcmstb: Remove resource checks
dt-bindings: reset: Fix brcmstb-reset example
...
Here are a number of small staging and IIO driver fixes for reported
issues for 5.5-rc2
Nothing major, a bunch of tiny IIO driver issues resolved, and some
staging driver fixes for things that people ran into with 5.5-rc1. Full
details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXfT+cg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykdqQCdGFa/Gafh4bWklhqQ9o0BSr7xzgMAn2DADxOp
Ii2JEMss9lSS158I567k
=coTA
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a number of small staging and IIO driver fixes for reported
issues for 5.5-rc2
Nothing major, a bunch of tiny IIO driver issues resolved, and some
staging driver fixes for things that people ran into with 5.5-rc1.
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
fbtft: Fix the initialization from property algorithm
staging: rtl8712: fix interface sanity check
staging: rtl8188eu: fix interface sanity check
staging: gigaset: add endpoint-type sanity check
staging: gigaset: fix illegal free on probe errors
staging: gigaset: fix general protection fault on probe
staging: vchiq: call unregister_chrdev_region() when driver registration fails
staging: exfat: fix multiple definition error of `rename_file'
staging/wlan-ng: add CRC32 dependency in Kconfig
staging: hp100: Fix build error without ETHERNET
staging: fbtft: Do not hardcode SPI CS polarity inversion
staging: exfat: properly support discard in clr_alloc_bitmap()
staging/octeon: Mark Ethernet driver as BROKEN
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
...
Json-schema requires a $ref to be under an 'allOf' if there are
additional constraints otherwise the additional constraints are
ignored. (Note that this behavior will be changed in draft8.)
Fixes: 641262f5e1 ("dt-bindings: memory: Add binding for NVIDIA Tegra30 External Memory Controller")
Fixes: 785685b7a1 ("dt-bindings: memory: Add binding for NVIDIA Tegra30 Memory Controller")
Fixes: 8da65c377b ("dt-bindings: memory: tegra30: Convert to Tegra124 YAML")
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
While my email address has changed for a while, all the schemas I
contributed still have the old one unfortunately. Update it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
After original patch was merged there were additional comments/requests
provided by Rob Herring [1]. Mostly they are related to json-schema usage,
and this patch fixes them. Also SPDX-License-Identifier has been changed to
(GPL-2.0-only OR BSD-2-Clause) as requested.
[1] https://lkml.org/lkml/2019/11/21/875
Fixes: ef63fe72f6 ("dt-bindings: net: ti: add new cpsw switch driver bindings")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[robh: Remove 2 more maxItems that aren't necessary]
Signed-off-by: Rob Herring <robh@kernel.org>
If the optional wdg interrupt is defined, then this property
may be defined.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The reset controller has a #reset-cells value of 1, so we should see a
phandle plus a register identifier, fix the example.
Fixes: 0807caf647 ("dt-bindings: reset: Add document for Broadcom STB reset controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3s3dwTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIKhhB/sE+kGrGECa6DSehxKsSTCvh/5AGw2U
AGh+AHgpfCRKOPNBeN0yKCdBVSE40fURsIjNvn5SDZ1cY8tUOVCJAyUU31MfgzkW
b+Xiro5iOu6G/UpfZgMCeGV617FZg/65rz7ylwNzzA7zuUcoml6o4A55/QUFNIXx
juDzhdKmpmLRQusekzbP9qyCgDGXv8/cPBloI+frzqaDU5bgS6Q3ldHe26lkQzNH
bwF6bCGpJYykuNFIrLoFpSuJ+7ttZhLexXCwsl90UfpwmHVvUgQKJuF8JVR1AF3x
5mjHWi3GFyi4aUL4yY4kU3cWWPse3MQLPt5QqMu56dW4UADp1k3FHByo
=YMzV
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.5-20191208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-12-08
this is a pull request of 13 patches for net/master.
The first two patches are by Dan Murphy. He adds himself as a maintainer to the
m-can MMIO and tcan SPI driver.
The next two patches the j1939 stack. The first one is by Oleksij Rempel and
fixes a locking problem found by the syzbot, the second one is by me an fixes a
mistake in the documentation.
Srinivas Neeli fixes missing RX CAN packets on CANFD2.0 in the xilinx driver.
Sean Nyekjaer fixes a possible deadlock in the the flexcan driver after
suspend/resume. Joakim Zhang contributes two patches for the flexcan driver
that fix problems with the low power enter/exit.
The next 4 patches all target the tcan part of the m_can driver. Sean Nyekjaer
adds the required delay after reset and fixes the device tree binding example.
Dan Murphy's patches make the wake-gpio optional.
In the last patch Xiaolong Huang fixes several kernel memory info leaks to the
USB device in the kvaser_usb_leaf driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
-----BEGIN PGP SIGNATURE-----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=vySY
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.5 cycle.
Mixture of old things people have just hit, and a few late breaking
issues with things that went in during the merge window.
Being sent promptly to resolve potential DT breakage causing
issues for binding test builds.
* ad7606
- Avoid reading extra data from the device over what was intended.
* ad7124
- Enable the internal reference when in use.
* ad7292
- Fix up license for newly added binding. Better to not have this go
out in a release with more limited header than intended.
- Fix a constraint on number of channels.
* ad7949
- Fix an issue which can result in readouts being from the wrong channel.
* hdc100x
- Fix wrong ABI usage (units) for relative humidity channel.
* intel mrfld
- Allocate right amount of private data (currently allocating too much).
* ltc2983
- Avoid a potential issue with machine endianness and wrong length device
tree read.
* max1027
- Clean up leak of an iio_trigger on probe failure.
* max9611
- Ensure we sleep long enough to successfully initialize the sensor.
* mpu6050
- Fix wrong ABI usage (units) for temperature channel.
* st_accel
- Fix an unused variable warning.
* st_lsm6dsx
- Fix decimation factor issue that can lead to missaligned datasets
(and hence garbage)
- Fix an issue with how we track enabled fifo channels.
- Avoid powering off the device if wake up events are enabled.
* tag 'iio-fixes-for-5.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
iio: adc: max1027: fix not unregistered iio trigger
iio: adc: intel_mrfld_adc: Allocating too much data in probe()
iio: adc: ad7124: Enable internal reference
dt-bindings: iio: adc: ad7292: fix constraint over channel quantity
dt-bindings: iio: adc: ad7292: Update SPDX identifier
iio: temperature: ltc2983: fix u32 read into a unsigned long long
iio: st_accel: Fix unused variable warning
iio: adc: ad7606: fix reading unnecessary data from device
Change items property of AD7292 channels to correctly constrain their
quantity.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update SPDX identifier to the preferred dual GPL-2.0 OR BSD-2-Clause
licensing.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The wake-up of the device can be configured as an optional feature of
the device. Move the wake-up gpio from a requried property to an
optional property.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change the reset pin example to active high to be in line with
the datasheet
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJd6cqnAAoJEAx081l5xIa+YR0P/A0LkilEbSnF/k7zKDjm0HN8
JGsf9ZfQRGA2y8URoLRtNdFjZfyuTSpiDSxsbDI0ShBhRimGHyCSxAJXO42vp8q3
jE57jBoaTSiGtagSO3nxrc1vQP7CfUpaggC2ilKSmcVvTrlqip6iPx7s2PoNyQYc
GRVUhkcylnZK5UrMiE8Yz/iNcy3Mh0X8bJQKXMEYxpW2KA3SL4qxuRlYIxXEoMyB
4MlWEV09wHTduf1uYuKdusHjILgR5EiVOdmbvpM92obqZOTokt5/S20TEdhFqiy0
0IHxuEkgVx+trXzGFbmqgh2I7BZvZIbKVCSnBT4AXAvUEJ99kGTdEP0I6uOp2lsC
1DCm+7/hcI8BlwmwC9N6ogUwoAzKn7DNc1urcet/0QVbnZLZlueUK/6fSgUNnUYe
miOeMNBmfHr83b75MpnNxYVoyz5S+/DFbtUplYKqxgjDYfiWWceSSE47NB+IHAiI
RVpz3AxGpKaw4/w5l2q8VuToWZxdO85TNjgVCTmKfwlYjIbEuveWpZNFqO/GHMm9
x50f4ZYVOjU2TEPnLQNTIJOgv71JrTpoAdFzPVwCeWUf4h4Y4lVLgTLvdG1JLcw+
k9BrA5z2R0kjzPtabRhS6WfSjpgSbY3DgY9hfi+HIUmKvZq4fdtAbBlp1oGSXJ9N
zkVrs9eE6Ahkcndi6ZV9
=3cs2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Various changes and minor fixes across a couple of drivers.
-----BEGIN PGP SIGNATURE-----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=Sd9F
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes and minor fixes across a couple of drivers"
* tag 'pwm/for-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32: Pass breakinput instead of its values
pwm: stm32: Remove clutter from ternary operator
pwm: stm32: Validate breakinput data from DT
pwm: Update comment on struct pwm_ops::apply
pwm: sun4i: Fix incorrect calculation of duty_cycle/period
pwm: stm32: Add power management support
pwm: stm32: Split breakinput apply routine to ease PM support
dt-bindings: pwm-stm32: Document pinctrl sleep state
pwm: sun4i: Drop redundant assignment to variable pval
dt-bindings: pwm: mediatek: Remove gratuitous compatible string for MT7629
Pull thermal management updates from Zhang Rui:
- Fix a deadlock regression in thermal core framework, which was
introduced in 5.3 (Wei Wang)
- Initialize thermal control framework earlier to enable thermal
mitigation during boot (Amit Kucheria)
- Convert the Intelligent Power Allocator (IPA) thermal governor to
follow the generic PM_EM instead of its own Energy Model (Quentin
Perret)
- Introduce a new Amlogic soc thermal driver (Guillaume La Roque)
- Add interrupt support for tsens thermal driver (Amit Kucheria)
- Add support for MSM8956/8976 in tsens thermal driver
(AngeloGioacchino Del Regno)
- Add support for r8a774b1 in rcar thermal driver (Biju Das)
- Add support for Thermal Monitor Unit v2 in qoriq thermal driver
(Yuantian Tang)
- Some other fixes/cleanups on thermal core framework and soc thermal
drivers (Colin Ian King, Daniel Lezcano, Hsin-Yi Wang, Tian Tao)
* 'thermal/next' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (32 commits)
thermal: Fix deadlock in thermal thermal_zone_device_check
thermal: cpu_cooling: Migrate to using the EM framework
thermal: cpu_cooling: Make the power-related code depend on IPA
PM / EM: Declare EM data types unconditionally
arm64: defconfig: Enable CONFIG_ENERGY_MODEL
drivers: thermal: tsens: fix potential integer overflow on multiply
thermal: cpu_cooling: Reorder the header file
thermal: cpu_cooling: Remove pointless dependency on CONFIG_OF
thermal: no need to set .owner when using module_platform_driver
thermal: qcom: tsens-v1: Fix kfree of a non-pointer value
cpufreq: qcom-hw: Move driver initialization earlier
clk: qcom: Initialize clock drivers earlier
cpufreq: Initialize cpufreq-dt driver earlier
cpufreq: Initialize the governors in core_initcall
thermal: Initialize thermal subsystem earlier
thermal: Remove netlink support
dt: thermal: tsens: Document compatible for MSM8976/56
thermal: qcom: tsens-v1: Add support for MSM8956 and MSM8976
MAINTAINERS: add entry for Amlogic Thermal driver
thermal: amlogic: Add thermal driver to support G12 SoCs
...
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes. The two major core
changes are Al Viro's reworking of sg's handling of copy to/from user,
Ming Lei's removal of the host busy counter to avoid contention in the
multiqueue case and Damien Le Moal's fixing of residual tracking
across error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeKvHCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQJMAQDAjlAi
SNfbyndMqyf+rZGWufDI+43Up1VvW9GeWJHeDwEAxfO5XZsCks2uT8UxXhpEp9L7
HkiUww3zbcgl0FWFkUM=
=cdVU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes.
The major core changes are Al Viro's reworking of sg's handling of
copy to/from user, Ming Lei's removal of the host busy counter to
avoid contention in the multiqueue case and Damien Le Moal's fixing of
residual tracking across error handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits)
scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort()
scsi: target: core: Fix a pr_debug() argument
scsi: iscsi: Don't send data to unbound connection
scsi: target: iscsi: Wait for all commands to finish before freeing a session
scsi: target: core: Release SPC-2 reservations when closing a session
scsi: target: core: Document target_cmd_size_check()
scsi: bnx2i: fix potential use after free
Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails"
scsi: NCR5380: Add disconnect_mask module parameter
scsi: NCR5380: Unconditionally clear ICR after do_abort()
scsi: NCR5380: Call scsi_set_resid() on command completion
scsi: scsi_debug: num_tgts must be >= 0
scsi: lpfc: use hdwq assigned cpu for allocation
scsi: arcmsr: fix indentation issues
scsi: qla4xxx: fix double free bug
scsi: pm80xx: Modified the logic to collect fatal dump
scsi: pm80xx: Tie the interrupt name to the module instance
scsi: pm80xx: Controller fatal error through sysfs
scsi: pm80xx: Do not request 12G sas speeds
scsi: pm80xx: Cleanup command when a reset times out
...
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of things to
convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just need
to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a variety of
systems (and to not take over huge systems entirely in particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need to
load a lot of paper.
- A script and documentation making it easy for maintainers to add Link:
tags at commit time.
Also included is the removal of a bunch of spurious CR characters.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl3j5B0PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YtBcH/jIN2cO8/0YW2rjVT+1G6ytSdFUKx5WJ/lpf
5uBeCvuCeYhtCB6+BgnXvjykJ7jDW11/NJNjWqz/gsvD5l5FJK1rXarI/oz2Klyi
kcPtDmBF/ki4wz9qXzEpa0vg8LXdjeys50S1vE75qCzxZoPP7YjuRbPnLrlIJukv
JbDVi4p9kxgeHfRB4+BHOe5rFwA3mMmaxKNIX34Y+UUO2KZ0g/yUi1bAaQwQAdt+
PsORmkVQ8Puh3K9xRIr7dYlcWBlBiPqzYdvDgTVxSjrxdK6wjYjSgVk2VjC5MBUN
mTSTWgyfsIcD/76/s8tq7ZRl2fw+SkCSkFo79Rb/hJwDTb7Vnng=
=LPBr
-----END PGP SIGNATURE-----
Merge tag 'docs-5.5a' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"Here are the main documentation changes for 5.5:
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of
things to convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just
need to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a
variety of systems (and to not take over huge systems entirely in
particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need
to load a lot of paper.
- A script and documentation making it easy for maintainers to add
Link: tags at commit time.
Also included is the removal of a bunch of spurious CR characters"
* tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits)
docs: remove a bunch of stray CRs
docs: fix up the maintainer profile document
libnvdimm, MAINTAINERS: Maintainer Entry Profile
Maintainer Handbook: Maintainer Entry Profile
MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile
docs, parallelism: Rearrange how jobserver reservations are made
docs, parallelism: Do not leak blocking mode to other readers
docs, parallelism: Fix failure path and add comment
Documentation: Remove bootmem_debug from kernel-parameters.txt
Documentation: security: core.rst: fix warnings
Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning
Documentation/translation: Use Korean for Korean translation title
docs/memory-barriers.txt: Remove remaining references to mmiowb()
docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section
Documentation/kokr: Kill all references to mmiowb()
docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section
docs: Add initial documentation for devfreq
Documentation: Document how to get links with git am
docs: Add request_irq() documentation
...
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
Including:
- Conversion of the AMD IOMMU driver to use the dma-iommu code
for imlementing the DMA-API. This gets rid of quite some code
in the driver itself, but also has some potential for
regressions (non are known at the moment).
- Support for the Qualcomm SMMUv2 implementation in the SDM845
SoC. This also includes some firmware interface changes, but
those are acked by the respective maintainers.
- Preparatory work to support two distinct page-tables per
domain in the ARM-SMMU driver
- Power management improvements for the ARM SMMUv2
- Custom PASID allocator support
- Multiple PCI DMA alias support for the AMD IOMMU driver
- Adaption of the Mediatek driver to the changed IO/TLB flush
interface of the IOMMU core code.
- Preparatory patches for the Renesas IOMMU driver to support
future hardware.
-----BEGIN PGP SIGNATURE-----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=ntaE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Conversion of the AMD IOMMU driver to use the dma-iommu code for
imlementing the DMA-API. This gets rid of quite some code in the
driver itself, but also has some potential for regressions (non are
known at the moment).
- Support for the Qualcomm SMMUv2 implementation in the SDM845 SoC.
This also includes some firmware interface changes, but those are
acked by the respective maintainers.
- Preparatory work to support two distinct page-tables per domain in
the ARM-SMMU driver
- Power management improvements for the ARM SMMUv2
- Custom PASID allocator support
- Multiple PCI DMA alias support for the AMD IOMMU driver
- Adaption of the Mediatek driver to the changed IO/TLB flush interface
of the IOMMU core code.
- Preparatory patches for the Renesas IOMMU driver to support future
hardware.
* tag 'iommu-updates-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (62 commits)
iommu/rockchip: Don't provoke WARN for harmless IRQs
iommu/vt-d: Turn off translations at shutdown
iommu/vt-d: Check VT-d RMRR region in BIOS is reported as reserved
iommu/arm-smmu: Remove duplicate error message
iommu/arm-smmu-v3: Don't display an error when IRQ lines are missing
iommu/ipmmu-vmsa: Add utlb_offset_base
iommu/ipmmu-vmsa: Add helper functions for "uTLB" registers
iommu/ipmmu-vmsa: Calculate context registers' offset instead of a macro
iommu/ipmmu-vmsa: Add helper functions for MMU "context" registers
iommu/ipmmu-vmsa: tidyup register definitions
iommu/ipmmu-vmsa: Remove all unused register definitions
iommu/mediatek: Reduce the tlb flush timeout value
iommu/mediatek: Get rid of the pgtlock
iommu/mediatek: Move the tlb_sync into tlb_flush
iommu/mediatek: Delete the leaf in the tlb_flush
iommu/mediatek: Use gather to achieve the tlb range flush
iommu/mediatek: Add a new tlb_lock for tlb_flush
iommu/mediatek: Correct the flush_iotlb_all callback
iommu/io-pgtable-arm: Rename IOMMU_QCOM_SYS_CACHE and improve doc
iommu/io-pgtable-arm: Rationalise MAIR handling
...
- New drivers for SiFive PDMA, Socionext Milbeaut HDMAC and XDMAC,
Freescale dpaa2 qDMA
- Support for X1000 in JZ4780
- Xilinx dma updates and support for Xilinx AXI MCDM controller
- New bindings for rcar R8A774B1
- Minor updates to dw, dma-jz4780, ti-edma, sprd drivers
-----BEGIN PGP SIGNATURE-----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=bDMV
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Here are the changes this time around, couple of new drivers and
updates to few more:
- New drivers for SiFive PDMA, Socionext Milbeaut HDMAC and XDMAC,
Freescale dpaa2 qDMA
- Support for X1000 in JZ4780
- Xilinx dma updates and support for Xilinx AXI MCDM controller
- New bindings for rcar R8A774B1
- Minor updates to dw, dma-jz4780, ti-edma, sprd drivers"
* tag 'dmaengine-5.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (61 commits)
dmaengine: Fix Kconfig indentation
dmaengine: sf-pdma: move macro to header file
dmaengine: sf-pdma: replace /** with /* for non-function comment
dmaengine: ti: edma: fix missed failure handling
dmaengine: mmp_pdma: add missed of_dma_controller_free
dmaengine: mmp_tdma: add missed of_dma_controller_free
dmaengine: sprd: Add wrap address support for link-list mode
MAINTAINERS: Add Green as SiFive PDMA driver maintainer
dmaengine: sf-pdma: add platform DMA support for HiFive Unleashed A00
dt-bindings: dmaengine: sf-pdma: add bindins for SiFive PDMA
dmaengine: zx: remove: removed dmam_pool_destroy
dmaengine: mediatek: hsdma_probe: fixed a memory leak when devm_request_irq fails
dmaengine: iop-adma: clean up an indentation issue
dmaengine: milbeaut-xdmac: remove redundant error log
dmaengine: milbeaut-hdmac: remove redundant error log
dmaengine: dma-jz4780: add missed clk_disable_unprepare in remove
dmaengine: JZ4780: Add support for the X1000.
dt-bindings: dmaengine: Add X1000 bindings.
dmaengine: xilinx_dma: Add Xilinx AXI MCDMA Engine driver support
dmaengine: xilinx_dma: Extend dma_config struct to store irq routine handle
...
Pull input updates from Dmitry Torokhov:
- updates to Ilitech driver to support ILI2117
- face lift of st1232 driver to support MT-B protocol
- a new driver for i.MX system controller keys
- mpr121 driver now supports polling mode
- various input drivers have been switched away from input_polled_dev
to use polled mode of regular input devices
- other assorted cleanups and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
Input: synaptics-rmi4 - fix various V4L2 compliance problems in F54
Input: synaptics - switch another X1 Carbon 6 to RMI/SMbus
Input: fix Kconfig indentation
Input: imx_sc_key - correct SCU message structure to avoid stack corruption
Input: ili210x - optionally show calibrate sysfs attribute
Input: ili210x - add resolution to chip operations structure
Input: ili210x - do not retrieve/print chip firmware version
Input: mms114 - use device_get_match_data
Input: ili210x - remove unneeded suspend and resume handlers
Input: ili210x - do not unconditionally mark touchscreen as wakeup source
Input: ili210x - define and use chip operations structure
Input: ili210x - do not set parent device explicitly
Input: ili210x - handle errors from input_mt_init_slots()
Input: ili210x - switch to using threaded IRQ
Input: ili210x - add ILI2117 support
dt-bindings: input: touchscreen: ad7879: generic node names in example
Input: ar1021 - fix typo in preprocessor macro name
Input: synaptics-rmi4 - simplify data read in rmi_f54_work
Input: kxtj9 - switch to using polled mode of input devices
Input: kxtj9 - switch to using managed resources
...
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
-----BEGIN PGP SIGNATURE-----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=KJ0/
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
* tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: imx: add support for imx v1 mu
dt-bindings: mailbox: imx-mu: add imx7ulp MU support
mailbox: imx: Clear the right interrupts at shutdown
mailbox: imx: Fix Tx doorbell shutdown path
mailbox: stm32-ipcc: Update wakeup management
mailbox: no need to set .owner platform_driver_register
mailbox/omap: Handle if CONFIG_PM is disabled
This adds support for booting the modem processor on Qualcomm MSM8998
and carries some cleanup up and bug fixes to the framework and the stm32
driver.
-----BEGIN PGP SIGNATURE-----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=TxbM
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for booting the modem processor on Qualcomm MSM8998
and carries some cleanup up and bug fixes to the framework and the
stm32 driver"
* tag 'rproc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
Revert "dt-bindings: remoteproc: stm32: add wakeup-source"
remoteproc: stm32: fix probe error case
remoteproc: stm32: wakeup the system by wdg irq
dt-bindings: remoteproc: stm32: add wakeup-source
remoteproc: Fix wrong rvring index computation
remoteproc: stm32: use workqueue to treat mailbox callback
remoteproc: fix argument 2 of rproc_mem_entry_init
remoteproc: qcom_q6v5_mss: Add support for MSM8998
dt-bindings: remoteproc: qcom: Add Q6v5 Modem PIL binding for MSM8998
remoteproc: debug: Remove unneeded NULL check
remoteproc: remove useless typedef
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl3hODMACgkQ+iyteGJfRsoyYgCcDMibAAvqUQ2OqbEAwPMp5E5z
4GgAnRU4PolSaZjAP1lvqeqjM8biwbRg
=Z1pz
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.5-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- support for NCT6116D
- several small fixes and improvements
* tag 'linux-watchdog-5.5-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
watchdog: jz4740: Drop dependency on MACH_JZ47xx
watchdog: jz4740: Use regmap provided by TCU driver
watchdog: jz4740: Use WDT clock provided by TCU driver
dt-bindings: watchdog: sama5d4_wdt: add microchip,sam9x60-wdt compatible
watchdog: sama5d4_wdt: cleanup the bit definitions
watchdog: sprd: Fix the incorrect pointer getting from driver data
watchdog: aspeed: Fix clock behaviour for ast2600
watchdog: imx7ulp: Fix reboot hang
watchdog: make nowayout sysfs file writable
watchdog: prevent deferral of watchdogd wakeup on RT
watchdog: imx7ulp: Use definitions instead of magic values
watchdog: imx7ulp: Remove inline annotations
watchdog: imx7ulp: Remove unused structure member
watchdog: imx7ulp: Pass the wdog instance inimx7ulp_wdt_enable()
watchdog: wdat_wdt: Spelling s/configrable/configurable/
watchdog: bd70528: Trivial function documentation fix
watchdog: cadence: Do not show error in case of deferred probe
watchdog: Fix the race between the release of watchdog_core_data and cdev
watchdog: sbc7240_wdt: Fix yet another -Wimplicit-fallthrough warning
watchdog: intel-mid_wdt: Add WATCHDOG_NOWAYOUT support
...
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace. After clear input from the RaspberryPi and Beagle
communities, it has been established that prototyping,
industrial automation and make communities strongly need
this feature, and as we want people to use the character
device, we have implemented the simple pull up/down
interface for GPIO lines. This means we can specify that
a (chip-specific) pull up/down resistor can be enabled,
but does not offer fine-grained control such as cases
where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out
the old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it
in all GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when
cooperating with the pin control subsystem and registering
ranges as part of adding a gpiolib driver and a
gpio_irq_chip driver at the same time. This is also
deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained
handler.
-----BEGIN PGP SIGNATURE-----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=o13I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.5 kernel cycle
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace.
After clear input from the RaspberryPi and Beagle communities, it
has been established that prototyping, industrial automation and
make communities strongly need this feature, and as we want people
to use the character device, we have implemented the simple pull
up/down interface for GPIO lines.
This means we can specify that a (chip-specific) pull up/down
resistor can be enabled, but does not offer fine-grained control
such as cases where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out the
old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it in all
GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when cooperating with
the pin control subsystem and registering ranges as part of adding
a gpiolib driver and a gpio_irq_chip driver at the same time. This
is also deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained handler"
* tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits)
gpio: Add TODO item for regmap helper
Documentation: gpio: driver.rst: Fix warnings
gpio: of: Fix bogus reference to gpiod_get_count()
gpiolib: Grammar s/manager/managed/
gpio: lynxpoint: Setup correct IRQ handlers
MAINTAINERS: Replace my email by one @kernel.org
gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK
gpio/mpc8xxx: fix qoriq GPIO reading
gpio: mpc8xxx: Don't overwrite default irq_set_type callback
gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors
gpiolib: fix coding style in gpiod_hog()
drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()
gpio: merrifield: Pass irqchip when adding gpiochip
gpio: merrifield: Add GPIO <-> pin mapping ranges via callback
gpiolib: Introduce ->add_pin_ranges() callback
gpio: mmio: remove untrue leftover comment
gpio: em: Use platform_get_irq() to obtain interrupts
gpio: tegra186: Add debounce support
gpio: tegra186: Program interrupt route mapping
gpio: tegra186: Derive register offsets from bank/port
...
+ OCMEM support to enable the couple generations that had shared OCMEM
rather than GMEM exclusively for the GPU (late a3xx and I think basically
all of a4xx). Bjorn and Brian decided to land this through the drm
tree to avoid having to coordinate merge requests.
+ a510 support, and various associated display support
+ the usual misc cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv-JWswEJRxe5AmnGQO1SZnpxK05kO1E29K6UUzC9GMMw@mail.gmail.com
- Add support for a "resource managed strongly uncachable ioremap" call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
- New Drivers
- Add support for MediaTek MT6323 PMIC
- New Device Support
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
- New Functionality
- Add support for requested supply clocks; madera-core
- Fix-ups
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona, syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
- Bug Fixes
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc
-----BEGIN PGP SIGNATURE-----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=mugH
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
Jagan Teki