[ Upstream commit 1b2cfa2d1d ]
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc1c2048ab upstream.
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b3ea2a06d upstream.
gpiod_add_lookup_table() expects the gpiod_lookup_table->table passed to
it to be terminated with a zero-ed out entry.
So we need to allocate one more entry then we will use.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b884fe71f upstream.
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cb4c67d77 ]
This reverts commit 02b9aec592.
As talked about in the patch ("soc: qcom: geni: More properly switch
to DMA mode"), swapping the order of geni_se_setup_m_cmd() and
geni_se_xx_dma_prep() can sometimes cause corrupted transfers. Thus
we traded one problem for another. Now that we've debugged the
problem further and fixed the geni helper functions to more disable
FIFO interrupts when we move to DMA mode we can revert it and end up
with (hopefully) zero problems!
To be explicit, the patch ("soc: qcom: geni: More properly switch
to DMA mode") is a prerequisite for this one.
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.2.I7b22281453b8a18ab16ef2bfd4c641fb1cc6a92c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1de67a3dee upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f7 upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e6fe59ed upstream.
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aafced673c ]
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e50e4f0b85 upstream.
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8w9z
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.2.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 8058d69905 ]
Commit 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181 ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f5b3f43364 upstream.
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af4 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1334d3b4e4 upstream.
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28683e847e upstream.
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 845b89127b upstream.
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c79 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
[iwamatsu: Use DPM_FLAG_NEVER_SKIP instead of DPM_FLAG_NO_DIRECT_COMPLETE]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a2bd970aa6 ]
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21653a4181 ]
Some ACPI i2c-devices _STA method (which is used to detect if the device
is present) use autodetection code which probes which device is present
over i2c. This requires the I2C ACPI OpRegion handler to be registered
before we enumerate i2c-clients under the i2c-adapter.
This fixes the i2c touchpad on the Lenovo ThinkBook 14-IIL and
ThinkBook 15 IIL not getting an i2c-client instantiated and thus not
working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1842039
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a1d6db23d ]
Mask the IRQ status to only the bits that the driver checks. This
prevents excessive driver warnings when operating in slave mode
when additional bits are set that the driver doesn't handle.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44c99904cf ]
Depending on the board design, the I2C controllers found on Tegra SoCs
may require pinmuxing in order to function. This is done as part of the
driver's runtime suspend/resume operations. However, the PM core does
not allow devices to go into runtime suspend during system sleep to
avoid potential races with the suspend/resume of their parents.
As a result of this, when Tegra SoCs resume from system suspend, their
I2C controllers may have lost the pinmux state in hardware, whereas the
pinctrl subsystem is not aware of this. To fix this, make sure that if
the I2C controller is not runtime suspended, the runtime suspend code is
still executed in order to disable the module clock (which we don't need
to be enabled during sleep) and set the pinmux to the idle state.
Conversely, make sure that the I2C controller is properly resumed when
waking up from sleep so that pinmux settings are properly restored.
This fixes a bug seen with DDC transactions to an HDMI monitor timing
out when resuming from system suspend.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5d5605ca3 ]
Potentially it is possible that interrupt may fire after transfer timeout.
That may not end up well for the next transfer because interrupt handling
may race with hardware resetting.
This is very unlikely to happen in practice, but anyway let's prevent the
potential problem by enabling interrupt only at the moments when it is
actually necessary to get some interrupt event.
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ot99
-----END PGP SIGNATURE-----
Merge tag 'v5.4.67' into 5.4-2.2.x-imx
This is the 5.4.67 stable release
This updates the kernel present in the NXP release imx_5.4.47_2.2.0 to the
latest patchset available from stable korg.
Base stable kernel version present in the NXP BSP release is v5.4.47.
Following conflicts were recorded and resolved:
- arch/arm/mach-imx/pm-imx6.c
NXP version has a different PM vectoring scheme, where the IRAM bottom
half (8k) is used to store IRAM code and pm_info. Keep this version to
be compatible with NXP PM implementation.
- arch/arm64/boot/dts/freescale/imx8mm-evk.dts
- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
NXP patches kept to provide proper LDO setup:
imx8mm-evk.dts: 975d8ab07267ded741c4c5d7500e524c85ab40d3
imx8mn-ddr4-evk.dts: e8e35fd0e759965809f3dca5979a908a09286198
- drivers/crypto/caam/caamalg.c
Keep NXP version, as it already covers the functionality for the
upstream patch [d6bbd4eea2]
- drivers/gpu/drm/imx/dw_hdmi-imx.c
- drivers/gpu/drm/imx/imx-ldb.c
- drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
Port changes from upstream commit [1a27987101], which extends
component lifetime by moving drm structures allocation/free from
bind() to probe().
- drivers/gpu/drm/imx/imx-ldb.c
Merge patch [1752ab50e8] from upstream to disable both LVDS channels
when Enoder is disabled
- drivers/mmc/host/sdhci-esdhc-imx.c
Fix merge fuzz produced by [6534c897fd].
- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
Commit d1a00c9bb1 from upstream solves the issue with improper error
reporting when qdisc type support is absent. Upstream version is merged
into NXP implementation.
- drivers/net/ethernet/freescale/enetc/enetc.c
Commit [ce06fcb6a6] from upstream merged,
base NXP version kept
- drivers/net/ethernet/freescale/enetc/enetc_pf.c
Commit [e8b86b4d87] from upstream solves
the kernel panic in case if probing fails. NXP has a clean-up logic
implemented different, where the MDIO remove would be invoked in any
failure case. Keep the NXP logic in place.
- drivers/thermal/imx_thermal.c
Upstream patch [9025a5589c] adds missing
of_node_put call, NXP version has been adapted to accommodate this patch
into the code.
- drivers/usb/cdns3/ep0.c
Manual merge of commit [be8df02707] from
upstream to protect cdns3_check_new_setup
- drivers/xen/swiotlb-xen.c
Port upstream commit cca58a1669 to NXP tree, manual hunk was
resolved during merge.
- sound/soc/fsl/fsl_esai.c
Commit [53057bd4ac] upstream addresses the problem of endless isr in
case if exception interrupt is enabled and tasklet is scheduled. Since
NXP implementation has tasklet removed with commit [2bbe95fe6c],
upstream fix does not match the main implementation, hence we keep the
NXP version here.
- sound/soc/fsl/fsl_sai.c
Apply patch [b8ae2bf5cc] from upstream, which uses FIFO watermark
mask macro.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit 66d402e2e9 upstream.
On suspend the original host configuration gets restored. The
resume routine has to undo this, otherwise the SMBus master
may be left in disabled state or in i2c mode.
[JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.]
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6eb158ec0a ]
The driver-specific usage of the DMA_CTRL_ACK flag was replaced with a
custom flag in commit ceeeb99cd8 ("dmaengine: mxs: rename custom flag"),
but i2c-mxs was not updated to use the new flag, completely breaking I2C
transactions using DMA.
Fixes: ceeeb99cd8 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a355aeb24 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 914a7b3563 ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3cb82c6d6 ]
When commit c64ffff7a9 ("i2c: core: Allow empty id_table in ACPI case
as well") fixed the enumeration of I²C devices on ACPI enabled platforms
when driver has no ID table, it missed the PRP0001 support.
i2c_device_match() and i2c_acpi_match_device() differently match
driver against given device. Use acpi_driver_match_device(), that is used
in the former, in i2c_device_probe() and don't fail PRP0001 enumeration
when no ID table exist.
Fixes: c64ffff7a9 ("i2c: core: Allow empty id_table in ACPI case as well")
BugLink: https://stackoverflow.com/q/63519678/2511795
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Claim clkhi and clklo as integer type to avoid possible calculation
errors caused by data overflow.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
(cherry picked from commit 5912ae411d8c7706bbed9a7139c0afe47da898b7)
[ Upstream commit c7c9e914f9 ]
Due to the lockless design of the driver, it is theoretically possible
to access a NULL pointer, if a slave interrupt was running while we were
unregistering the slave. To make this rock solid, disable the interrupt
for a short time while we are clearing the interrupt_enable register.
This patch is purely based on code inspection. The OOPS is super-hard to
trigger because clearing SAR (the address) makes interrupts even more
unlikely to happen as well. While here, reinit SCR to SDBS because this
bit should always be set according to documentation. There is no effect,
though, because the interface is disabled.
Fixes: 7b814d852a ("i2c: rcar: avoid race when unregistering slave client")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314139f9f0 ]
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The clkhi and clklo ratio was not very precise before that can make the
time of START/STOP/HIGH LEVEL out of specification.
Therefore, the calculation of these times has been modified in this patch.
At the same time, the mode rate definition of i2c is corrected.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
(cherry picked from commit 124d288c85caab0f868cec5387a1a32f39871392)
[ Upstream commit 0db9254d6b ]
This reverts commit d358def706.
There are two issues with "i2c: cadence: Fix the hold bit setting" commit.
1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.
2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.
The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.
The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02b9aec592 ]
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb01597158 ]
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f90786b31 ]
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrey Zhizhikin