All the current clients of this API assume that 0 corresponds
to a failure and non-zero to a pass therefore ignoring the need to
handle a negative error code.
This commit modifies the API to follow that standard since returning a
negative (EINVAL) doesn't seem to provide enough value to justify
the need to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert Dialog Semiconductor DA9xxx regulator drivers to SPDX identifier.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For fixed regulator, setting .n_voltages = 1 and .fixed_uV is enough,
no need to set .min_uV and .list_volage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slightly better readability by setting fixed_uV instead of min_uV.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables and ab3100_regulator_desc array never need
to be modified, make them const so compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert Powerventure Semiconductor PV88060/PV88080/PV88090 regulator
drivers to SPDX identifier.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *regdev and *regmap can be replaced by local variables in probe().
Only desc of struct vexpress_regulator is really need, so just use
struct regulator_desc directly and remove struct vexpress_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the fields in struct sy8106a are only used in sy8106a_i2c_probe(), so
use local variables instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Temporary failures to get a regulator (EPROBE_DEFER) should be logged
as debug information instead of errors.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *regmap and *rdev can be replaced by local variables.
The slew_rate is no longer used since commit dd7e71fbee
("regulator: fan53555: use set_ramp_delay to set the ramp up slew rate").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After converting to use simplified DT parsing, the struct ltc3589_regulator
only has a desc member. So let's remove struct ltc3589_regulator and use
struct regulator_desc instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simplify the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code always set pmic->rinfo[id] = &max77620_regs_info[id];
It should set to either max77620_regs_info or max20024_regs_info
depends on the chip_id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I went to great lengths to hand over the management of the GPIO
descriptors to the regulator core, and some stray rebased
oneliner in the old patch must have been assuming the devices
were still doing devres management of it.
We handed the management over to the regulator core, so of
course the regulator core shall issue gpiod_put() when done.
Sorry for the descriptor leak.
Fixes: 541d052d72 ("regulator: core: Only support passing enable GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 6cdae8173f ("regulator: Add support for stm32 power regulators")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 6cdae8173f ("regulator: Add support for stm32 power regulators")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables and tps80031_dcdc_voltages array never need
to be modified, make them const so compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct voltage_map_desc is used for storing min/max/step fileds, and
then setup the min_uV, uV_step and n_voltages fields for regulator_desc.
Introduce MAX8998_LINEAR_REG/MAX8998_OTHERS_REG macro to setup these filds
directly in regulator_desc to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to store
*rdev for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_get_current_limit_regmap helper to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to save
*regulator for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ab8500_ext_regulator_ops never need to be modified, make it const so
compiler can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simplify the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so we don't need to save
*rdev for clean up, use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *dev is assigned but not used, remove it.
Current driver is using devm_regulator_register(), so no neeed to save
*rdev for clean up. Use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simplify the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems a little bit odd current code pass struct regulator_config rather
than a pointer to setup_regulators. The setup_regulators is so simple and
only has one caller, so remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the context with rdev, we can use rdev->regmap instead of mcp->rmap.
The *rdev[NUM_REGULATORS] is not required because current code uses
devm_regulator_register() so we don't need to store *rdev for clean up
paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
vexpress_regulator_ops_ro and vexpress_regulator_ops are never changed,
make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These fields are only used in anatop_regulator_probe() so use local
variables instead. The *initdata is not used so can be removed.
The *anatop is renamed to *regmap for better readability.
Use u32 instead of int for the variables used as third argument of
of_property_read_u32().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The S2MPA01_REGULATOR_CNT is no longer used after converted to use
simplified DT parsing.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rdev->desc->enable_mask setting is always the same as
BIT(regulator->ctrl_mask), so just use rdev->desc->enable_mask instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators array should never need to be modified, make it const so
compiler can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() instead of directly access rdev->desc->id.
While at it also remove unneeded init for ramp_value variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep reports the following issue on my setup:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&(&rdev->disable_work)->work));
lock(regulator_list_mutex);
lock((work_completion)(&(&rdev->disable_work)->work));
lock(regulator_list_mutex);
The problem is that regulator_unregister takes the
regulator_list_mutex and then calls flush_work on disable_work. But
regulator_disable_work calls regulator_lock_dependent which will
also take the regulator_list_mutex. Resulting in a deadlock if the
flush_work call actually needs to flush the work.
Fix this issue by moving the flush_work outside of the
regulator_list_mutex. The list mutex is not used to guard the point at
which the delayed work is queued, so its use adds no additional safety.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to
.rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a local variable *desc to avoid too many change lines due to over 80
characters.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register so no need to save *rdev for
clean up.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tps6507x_pmic_ops never need to be modified, make it const so compiler
can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct rc5t583_regulator only has 2 members, the *rdev is no longer
used because this driver is using devm_regulator_register now. After remove
*rdev, only *reg_info left. We can use struct rc5t583_regulator_info
directly, so remove struct rc5t583_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act8865_ops and act8865_ldo_ops never need to be modified,
make them const so compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation. With this conversion, also move the NULL test against pdata
in act8865_get_regulator_data() to the caller. This makes it clear the
code path to explicitly set init_data is for non-DT case only.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet the latest seletor 11 1111b = 3.3 V.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators array should never need to be modified, make it const so
compiler can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Covnert the header of the source file to SPDX.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables never need to be modified, make them const so
compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver does not use any syscon APIs, so remove MFD_SYSCON dependency.
Select REGMAP_MMIO since this driver uses devm_regmap_init_mmio().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
selector 0xB (1011) should be 2.6V rather than 2.7V, fit ix.
Table 5-4. LDOA1 Output Voltage Options
VID Bits VOUT VID Bits VOUT VID Bits VOUT VID Bits VOUT
0000 1.35 0100 1.8 1000 2.3 1100 2.85
0001 1.5 0101 1.9 1001 2.4 1101 3.0
0010 1.6 0110 2.0 1010 2.5 1110 3.3
0011 1.7 0111 2.1 1011 2.6 1111 Not Used
Fixes: d2a2e729a6 ("regulator: tps65086: Add regulator driver for the TPS65086 PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original code separates the selector 25-52 into 2 ranges on purpose
because DCDC1/DCDC3 only support up to 1.8V/1.5V in the old code.
Both DCDC1 and DCDC3 support up to 3.3V since commit b4c2e158a1
("regulator: tps65217: Allow DCDC1 and DCDC3 up to 3.3V"), so merge
25-30 and 31-52 ranges to one range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tps65132_regulator_ops and tps_regs_desc never need to be modified,
make them const so compiler can put them to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_freq’:
drivers/regulator/axp20x-regulator.c:1023:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
reg = AXP803_DCDC_FREQ_CTRL;
drivers/regulator/axp20x-regulator.c:1025:2: note: here
case AXP806_ID:
^~~~
drivers/regulator/axp20x-regulator.c: In function ‘axp20x_set_dcdc_workmode’:
drivers/regulator/axp20x-regulator.c:1115:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
reg = AXP806_DCDC_MODE_CTRL2;
drivers/regulator/axp20x-regulator.c:1121:2: note: here
case AXP221_ID:
^~~~
Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_desc never need to be modified, so define them as const as a
hint to the compiler that they can go into .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix sparse warning:
drivers/regulator/of_regulator.c:374:20:
warning: symbol 'regulator_of_get_init_node' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During several error paths in the function
regulator_set_voltage_unlocked() the value of 'ret' can take on negative
error values. However, in calls that go through the 'goto out' statement,
this return value is lost and return 0 is used instead, indicating a
'pass'.
There are several cases where this function should legitimately return a
fail instead of a pass: one such case includes constraints check during
voltage selection in the call to regulator_check_voltage(), which can
have -EINVAL for the case when an unsupported voltage is incorrectly
requested. In that case, -22 is expected as the return value, not 0.
Fixes: 9243a195be ("regulator: core: Change voltage setting path")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdev won't be NULL in .enable callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[The original commit was sent against -next but needed to be sent as a
bugfix, however -next had some additional changes which needed to be
reverted. Now everything is all in one branch applying the rest of the
changes to fix up the merge issue -- broonie]
commit e5e21f70bf ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bf ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss@opensource.diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss@opensource.diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LP87565_BUCK_0 is missed, fix it.
Fixes: f0168a9bf ("regulator: lp87565: Add support for lp87565 PMIC regulators")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it consistent as .volt_table should be const unsigned int *.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it consistent as .volt_table should be const unsigned int *.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it consistent as .volt_table should be const unsigned int *.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it consistent as .volt_table should be const unsigned int *.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver does not really need struct as3711_regulator_info and
struct as3711_regulator, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using regulator core's simplified DT parsing code,
so regulator will call regulator_of_get_init_data() to get init_data.
No need to set config.init_data. In additional, current code does not
properly set the init_data setting, so just remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so it is not necessary
to save as3722_regs->rdevs[id] for clean up.
The *rdevs[] is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove #ifdef CONFIG_OF guard so linux/of.h will be included when
!CONFIG_OF. This fixes build warnings when !CONFIG_OF.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator core's simplified DT parsing code to simply the driver
implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct pm800_regulators only has 2 members: *chip and *map.
The pm800_data->chip is not used. The pm800_data->map is not necessary.
Thus remove the struct pm800_regulators.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
.set_current_limit callback should select the current closest to max_uA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
.set_current_limit callback should select the current closest to max_uA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d1c6b4fe66 ("regulator: Add WM831x LDO support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d4d6b722e7 ("regulator: Add WM831x ISINK support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has been converted to use regulator core's simplified DT
parsing code. So the match_init_data/match_of_node functions are not
necessary now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The da903x driver produces an annoying false-positive warning
when built with clang:
drivers/regulator/da903x.c:395:2: error: division by zero is undefined [-Werror,-Wdivision-by-zero]
DA9030_LDO(13, 2100, 2100, 0, INVAL, 0, 0, RCTL11, 3), /* fixed @2.1V */
^ ~
drivers/regulator/da903x.c:359:2: note: expanded from macro 'DA9030_LDO'
DA903x_LDO(DA9030, _id, min, max, step, vreg, shift, nbits, ereg, ebit)
^ ~~~~
drivers/regulator/da903x.c:320:39: note: expanded from macro 'DA903x_LDO'
.n_voltages = (step) ? ((max - min) / step + 1) : 1, \
^ ~~~~
drivers/regulator/da903x.c:415:2: error: division by zero is undefined [-Werror,-Wdivision-by-zero]
DA9034_LDO(5, 3100, 3100, 0, INVAL, 0, 0, OVER3, 7), /* fixed @3.1V */
^ ~
drivers/regulator/da903x.c:356:2: note: expanded from macro 'DA9034_LDO'
DA903x_LDO(DA9034, _id, min, max, step, vreg, shift, nbits, ereg, ebit)
^ ~~~~
drivers/regulator/da903x.c:320:39: note: expanded from macro 'DA903x_LDO'
.n_voltages = (step) ? ((max - min) / step + 1) : 1, \
^ ~~~~
I already reported this as a bug in clang, but it may take a
while to fix it. As I have not been able to come up with any
reasonable workaround, I would just disable compilation here.
Link: https://bugs.llvm.org/show_bug.cgi?id=38789
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f307a7e9b7 ("regulator: pv88060: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 37b918a034 ("regulator: Add LTC3676 support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 3eb2c7ecb7 ("regulator: Add LTC3589 support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: b59320cc5a ("regulator: lp8755: new driver for LP8755")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 1028a37daa ("regulator: da9211: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 69ca3e58d1 ("regulator: da9063: Add Dialog DA9063 voltage regulators support.")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: e4ee831f94 ("regulator: Add WM831x DC-DC buck convertor support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: c90456e36d ("regulator: pv88090: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 99cf3af5e2 ("regulator: pv88080: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 4068e5182a ("regulator: da9062: DA9062 regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f6130be652 ("regulator: DA9055 regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_regulator_voltage_ops and gpio_regulator_current_ops should never
change, make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use WM8400_DC2_ENA_MASK for DCDC2 enable_mask.
The define is the same as WM8400_DC1_ENA_MASK, just a cleanup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only user of wm8400_block_read/wm8400_set_bits functions is the
wm8400 regulator driver. At the context of all the callers, we can
use regmap_bulk_read/regmap_update_bits directly.
Thus remove wm8400_block_read/wm8400_set_bits functions.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register() so it is not necessary
to save reg->rdev for clean up. Remove *rdev from struct ab3100_regulator,
then ab3100_regulators_remove() can be removed as well.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register() so it is not necessary
to save *rdev for clean up. Actually the pmic->rdev[id] is not used now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These regulator_ops variables should never change, make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The palmas_smps_ramp_delay array should never modify, make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>;
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_set/get_current_limit_regmap helpers to save some code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By setting curr_table, n_current_limits, csel_reg and csel_mask, the
regmap users can use regulator_set_current_limit_regmap and
regulator_get_current_limit_regmap for set/get_current_limit callbacks.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for suspend/resume and runtime PM to stm32-vrefbuf driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The *i2c and *i2c_8606 are no longer used since this driver was converted
to use regmap helpers. The *chip and *regulator are not really required.
So remove these unused fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set volt_table filed then we can use regulator_list_voltage_table.
Since we have volt_table setting, now we can remove vol_table from
struct pm8607_regulator_info.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
They should never change, make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver uses regulator_get/set_voltage_sel_regmap so it does not use
vsel_shift. Actually, vsel_shift can be calculated by vsel_mask setting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code does not really avoid array access out of bounds,
fix it by add checking for pdata->slew_rate.
If pdata->slew_rate is too big, it's a bug in pdata that needs fix.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup .vsel_reg and .vsel_mask then we can use the standard
set/get_voltage_sel_regmap helpers to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm831x_dcdc_ilim entries needs to be uA because it is used to compare
with min_uA and max_uA.
While at it also make the array const and change to use unsigned int.
Fixes: e4ee831f94 ("regulator: Add WM831x DC-DC buck convertor support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code already set .min_uV and .uV_step fields and it actually can
use regulator_list_voltage_linear.
So remove buck_volt_range and use regulator_list_voltage_linear instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code always return error, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Re-use the "tps65218_pmic_*_current_limit()" functions of LS3
and calculate the different required bit-shift by counting the
trailing 0s in "struct regulator_desc.csel_mask"
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s5m8767_opmode_reg should never change, make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When REGULATOR_CHANGE_DRMS is not set, drms_uA_update is a no-op.
It used to print a debug message, which was dropped in commit
8a34e979f6 ("regulator: refactor valid_ops_mask checking code")
Let's bring the debug message back, because it helps find missing
regulator-allow-set-load properties.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The lp873x_buck_ramp_delay should never change, make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FAN53526 differs from the FAN53555 only in that the mode bit in
VSEL0/VSEL1 is moved to the CONTROL register, the voltage selector mask
is extended by 1 bit and the step is different.
So extend the existing fan53555 driver to support FAN53526 as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use linear range to replace the twl6030ldo_list_voltage implementation.
With this change, the min_mV is not used and can be removed from
struct twlreg_info.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix list of valid LS3 currents from mA to µA
- Fix selection of min/max microAmps of LS3.
Selecting one of the configured values as max value now really
selects it instead of the next lower one
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, this is leading to static analysis warnings. However, rdev
can never be null, so the null check is redundant and can be removed.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: c90456e36d ("regulator: pv88090: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: 99cf3af5e2 ("regulator: pv88080: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off-by-one while iterating current_limits array.
The valid index should be 0 ~ n_current_limits -1.
Fixes: f307a7e9b7 ("regulator: pv88060: new regulator driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change buck1 voltage range to be conform with the data-sheet.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop using a regulator_init callback. This leads to a more simple regulator
registration code. This also permits to spuress struct stpmic1_regulator.
Also rename stpmic1_regulators_matches to stpmic1_matches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the regulator mode definition from the bindings header.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit e5e21f70bf ("regulator: core: Take lock before applying system
load") took the regulator lock before calling drms_uA_update() in order
to silence a lockdep warning during regulator_register().
However, we are not supposed to need locks at this point as the regulator
is in the process of being registered, so there should be no possibility
of concurrent access.
Instead, remove the unnecessary locking and simply drop the lockdep
annotation, since it is no longer valid.
Fixes: e5e21f70bf ("regulator: core: Take lock before applying system load")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the context with *rdev available, regulator core provides
rdev_get_id()/rdev_get_regmap() APIs to get regulator id and *regmap.
So no need to store them in struct stpmic1_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no vsel_reg/vsel_mask settings for PV88060_ID_SWx, so don't use
pv88060_ldo_ops for PV88060_SW. The PV88060_ID_SWx is fixed voltage,
set .fixed_uV instead of .min_uV then regulator core will automatically
support get_voltage and list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a remnant of commit 70a7fb80e8 ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is for LTC3676 rather than LTC1376.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use case range for continuous range to make the code shorter.
The .readable_reg and .writable_reg implementation are exactly the same,
so use a common ltc3676_readable_writeable_reg function instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
read ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator_desc_list_voltage_linear_range which can be used
by drivers for getting the voltages before regulator is registered.
This may be useful for drivers which need to fetch the voltage
selectors at device-tree parsing callback.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a result of exporting the bd70528 specific locking functions
we no longer need struct bd70528. Remove references to
struct bd70528 from bd70528 regulator.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are several lines in an if statement that are not indented
correctly. Fix these by removing the tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
linear range is suitable for this driver, let's convert it to linear range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device links are refcounted, device_link_remove() has to be called as
many times as device_link_add().
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With current n_voltages setting, regulator_list_voltage will return
-EINVAL when selector >=57. The highest selector is 0x41, so the
n_voltages should be 0x41+1, i.e. 66.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we changed all providers to pass descriptors into the core
for enable GPIOs instead of a global GPIO number, delete the support
for passing GPIO numbers in, and we get a cleanup and size reduction
in the core, and from a GPIO point of view we use the modern, cleaner
interface.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_* managed device resources and create a local
struct device *dev variable to simplify the code inside
probe().
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This pushes the handling of inversion semantics and open drain
settings to the GPIO descriptor and gpiolib. All affected board
files are also augmented.
This is especially nice since we don't have to have any
confusing flags passed around to the left and right littering
the fixed and GPIO regulator drivers and the regulator core.
It is all just very straight-forward: the core asks the GPIO
line to be asserted or deasserted and gpiolib deals with the
rest depending on how the platform is configured: if the line
is active low, it deals with that, if the line is open drain,
it deals with that too.
Cc: Alexander Shiyan <shc_work@mail.ru> # i.MX boards user
Cc: Haojian Zhuang <haojian.zhuang@gmail.com> # MMP2 maintainer
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> # OMAP1 maintainer
Cc: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> # EM-X270 maintainer
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # EZX maintainer
Cc: Philipp Zabel <philipp.zabel@gmail.com> # Magician maintainer
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Daniel Mack <zonque@gmail.com> # Raumfeld maintainer
Cc: Marc Zyngier <marc.zyngier@arm.com> # Zeus maintainer
Cc: Geert Uytterhoeven <geert+renesas@glider.be> # SuperH pinctrl/GPIO maintainer
Cc: Russell King <rmk+kernel@armlinux.org.uk> # SA1100
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> #OMAP1 Amstrad Delta
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the GPIO regulator driver to use decriptors only.
We have to let go of the array gpio handling: the fetched descriptors
are handled individually anyway, and the array retrieveal function
does not make it possible to retrieve each GPIO descriptor with
unique flags. Instead get them one by one.
We request the "enable" GPIO separately as before, and make sure
that this line is requested as nonexclusive since enable lines can
be shared and the regulator core expects this.
Most users of the GPIO regulator are using device tree.
There are two boards in the kernel using the gpio regulator from a
non-devicetree path: PXA hx4700 and magician. Make sure to switch
these over to use descriptors as well.
Cc: Philipp Zabel <p.zabel@pengutronix.de> # Magician
Cc: Petr Cvek <petr.cvek@tul.cz> # Magician
Cc: Robert Jarzmik <robert.jarzmik@free.fr> # PXA
Cc: Paul Parsons <lost.distance@yahoo.com> # hx4700
Cc: Kevin Hilman <khilman@baylibre.com> # Meson
Cc: Neil Armstrong <narmstrong@baylibre.com> # Meson
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It looks like linear range is suitable to describe the voltage table
for rk805 buck1/2:
selector 0 ~ 59: 0.7125V with uV_step = 12500
selector 60 ~ 62: 1.8V with uV_step = 200000
selector 63: 2.3V
With this change, then rk805 buck1/2 can reuse rk808_reg_ops_ranges.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
A comma has been accidentally used where a semi-colon was clearly
intended, correct this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK805 has the following voltage range for the BUCK1 and BUCK2 regulators:
From 0.7125V to 1.45V in 12.5mV steps, 1.8V, 2V, 2.2V and 2.3V
, which corresponds to the following values as per the RK805
datasheet:
000 000: 0.7125V
000 001: 0.725V
……
111 011: 1.45V
111 100: 1.8V
111 101: 2.0V
111 110: 2.2V
111 111: 2.3V
This means that the voltage range is not linear and so RK805 can not
reuse the same regulator_ops structure from RK808.
Fix it by creating a list with the correct supported voltage values
for RK805 BUCK1 and BUCK2 regulators.
Tested on a rv1108-elgin-r1 board that now correctly reports a BUCK2
voltage of 2.2V instead of the unsupported value of 1.4875V.
Fixes: c4e0d344c1 ("regulator: rk808: Add regulator driver for RK805")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure unwind all resources if probe fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a platform driver, no need to include linux/i2c.h.
Include linux/of.h for of_match_ptr.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator support for max77650. We support all four variants of this
PMIC including non-linear voltage table for max77651 SBB1 rail.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix copy-paste mistake while converting to use defines for masks.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is using devm_regulator_register, so it's not necessary to
store *rdev[3] in struct isl_pmic. Use a local variable instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While at it, also fix indent for rk805_reg_ops and rk805_switch_ops.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below build error:
drivers/regulator/mcp16502.c: In function ‘mcp16502_gpio_set_mode’:
drivers/regulator/mcp16502.c:135:3: error: implicit declaration of function ‘gpiod_set_value’; did you mean ‘gpio_set_value’? [-Werror=implicit-function-declaration]
gpiod_set_value(mcp->lpm, 0);
^~~~~~~~~~~~~~~
gpio_set_value
drivers/regulator/mcp16502.c: In function ‘mcp16502_probe’:
drivers/regulator/mcp16502.c:486:13: error: implicit declaration of function ‘devm_gpiod_get’; did you mean ‘devm_gpio_free’? [-Werror=implicit-function-declaration]
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~
devm_gpio_free
drivers/regulator/mcp16502.c:486:40: error: ‘GPIOD_OUT_LOW’ undeclared (first use in this function); did you mean ‘GPIOF_INIT_LOW’?
mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
^~~~~~~~~~~~~
GPIOF_INIT_LOW
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since devm_regmap_field_alloc can fail, add error checking for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like refactoring didn't go well and left ALDO2, DLDO2 and ELDO3
definitions broken for AXP803 - now they are using register address
instead of mask. Fix it by using mask where necessary.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons"), regulator node name comparisons are case sensitive.
The DA9052 driver uses uppercase, but the DT has lowercase.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Cc: Support Opensource <support.opensource@diasemi.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since c32569e358 ("regulator: Use of_node_name_eq for node name
comparisons") Vivien reported the mc13892-regulator complaining about
not being able to find regulators.
This is because prior to that commit we used of_node_cmp() to compare
the regulator array passed from mc13892_regulators down to
mc13xxx_parse_regulators_dt() and they are all defined in uppercase
letters by the MC13892_*_DEFINE* macros, whereas they are defined as
lowercase in the DTS.
Fix this by using a lowercase regulator name to match the DT node name.
Fixes: c32569e358 ("regulator: Use of_node_name_eq for node name comparisons")
Reported-by: Vivien Didelot <vivien.didelot@gmail.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_linear_range arrays and stpmic1_regulator_cfgs are only
accessed by this driver and the values are never changed so make them
static const. regulator_ops variables can also be const.
Also clean up a few empty lines in regulator_linear_range array.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD70528MWV is an ultra-low Iq general purpose single-chip power
management IC for battery-powered portable devices.
Add support for controlling 3 bucks and 3 LDOs present in
ROHM BD70528.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some scenarios the early stages of the boot chain has configured
regulators to be in a required state, but the later stages has skipped
to inform the RPM about it's requirements.
But as the SMD RPM regulators are being initialized voltage change
requests will be issued to align the voltage with the valid ranges. The
RPM aggregates all parameters for the specific regulator, the voltage
will be adjusted and the "enabled" state will be "off" - and the
regulator is turned off.
This patch addresses this problem by caching the requested enable state,
voltage and load and send the parameters in a batch, depending on the
enable state - effectively delaying the voltage request for disabled
regulators.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing MODULE_DEVICE_TABLE and remove the comma from the
separator on the end of the of_device_id array.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The act8600_sudcdc_voltage_ranges setting does not match the datasheet.
The problems in below entry:
REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000),
1. The off-by-one min_sel causes wrong volatage calculation.
The min_sel should be 192.
2. According to the datasheet[1] Table 7. (on page 43):
The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V.
Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM.
[1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf
Fixes: df3a950e4e ("regulator: act8865: Add act8600 support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having instance specific copy of desc is enough to support multiple
instance of pwm regulator.
The regulator_ops is never changed so no need to copy it per instance, make
pwm_regulator_voltage_table_ops and pwm_regulator_voltage_continuous_ops
const to ensure they won't be changed.
The pwm_regulator_desc is a template to be copied so also make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If regulator DT node doesn't exist, its of_parse_cb callback
function isn't called. Then all values for DT properties are
filled with zero. This leads to wrong register update for
FPS and POK settings.
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Provide a helper allowing to access regulator's regmap.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently rdev is dereferenced when assigning desc before rdev is null
checked, hence there is a potential null pointer dereference on rdev.
Fix this by null checking rdev first.
Detected by CoverityScan, CID#1476031 ("Dereference before null check")
Fixes: 77e3e3b165 ("regulator: axp20x: add software based soft_start for AXP209 LDO3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix few trivial language typos in core and drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use rdev_get_id() instead of directly access rdev->desc->id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown