commit 54ca955b5a upstream.
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f1496a923 ]
Setup the port uartclk in sifive_serial_probe() so that the base baud
rate is correctly printed during device probe instead of always showing
"0". I.e. the probe message is changed from
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 0) is a SiFive UART v0
to the correct:
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 115200) is a SiFive UART v0
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f70e49ed8 upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f16855dc upstream.
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c97f2a6fb3 upstream.
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:
TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)
The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.
And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).
So the "new" formula created by commit f77ebb241c has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.
Interestingly, in commit c2f448cff2 ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.
When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.
Many thanks to Michael for pointing out where to look.
Fixes: f77ebb241c ("tty: serial: fsl_lpuart: correct the FIFO depth size")
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by：Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c5fc92622 upstream.
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 912ab37c79 upstream.
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 534cf755d9 upstream.
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9ca43d42e upstream.
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce73460054 ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce73460054 ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Paras Sharma <parashar@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAl+ahE8ACgkQONu9yGCS
aT4j1A/9HzkKKoqZ2vXYQ1/uEnUqZech9ly1KxpNTBrSZYAtx3MaWY7tGDEx2BqD
y6iw9x4MymhHEbpwLg6YmmdWuMQLNNYJGoyLiPJgWhkE4c7zHadhNz1DcPEI8F7z
bSlUJ3Oebr8gzv0FvUmeVXw7Z2EuOqM1zGgTAZfnKY3DkYHbLnrzUJ4AiI8TNeba
pPIhjfIJ1TvhF+s5ggf2m8OtSWLZ0doCWCPmCFe2WyERX2WYCzPgsm0yL7L7oXME
ZqWpOcClBsiYekBNcZ4kxozhJtArCnv24n9VoXJ/YJIlWKvCA6uC8r527nGN/z08
dfFelj1nDs7/VrCSP4+109EjxLQnSYGgIWP0g0OsC+9wOmrQsYJ1azP1eNjm+NuC
hPa8uYVEZxwVyJuEfu4ZB4NMZBlD2qnHoskvBKbyZ8yaVnbvlMp552XMwsmJBpCs
8wArzabrJEz396LUUIYG829D7NBDuRav1Miu+FTzlbn+xZ/Y/S8OmhoG2stWa4wV
y5x0M0DWgrqiZ9rMkz9A03UNnCInQVTfIBoMl63xFitW4/0vLsln3+CjzlKm7H46
rD/tKACUoCDjR5DN+JwQzmTdL9zBb4p1cXwWjWb6rON3BkXmO0JVAxzurxI9PfX0
ZWDydZ3HNmrm0d3J12zf3kTX56PfPFAGWUsEc4Ntb5zdWXSQJsE=
=fZ3T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8w9z
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.2.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit 29788ab1d2 upstream.
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fb9342d06 ]
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac588759 ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d31676a8d ]
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42e11948dd ]
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cf4df30a9 ]
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f19c3f6c81 ]
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbd7814bb ]
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ot99
-----END PGP SIGNATURE-----
Merge tag 'v5.4.67' into 5.4-2.2.x-imx
This is the 5.4.67 stable release
This updates the kernel present in the NXP release imx_5.4.47_2.2.0 to the
latest patchset available from stable korg.
Base stable kernel version present in the NXP BSP release is v5.4.47.
Following conflicts were recorded and resolved:
- arch/arm/mach-imx/pm-imx6.c
NXP version has a different PM vectoring scheme, where the IRAM bottom
half (8k) is used to store IRAM code and pm_info. Keep this version to
be compatible with NXP PM implementation.
- arch/arm64/boot/dts/freescale/imx8mm-evk.dts
- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
NXP patches kept to provide proper LDO setup:
imx8mm-evk.dts: 975d8ab07267ded741c4c5d7500e524c85ab40d3
imx8mn-ddr4-evk.dts: e8e35fd0e759965809f3dca5979a908a09286198
- drivers/crypto/caam/caamalg.c
Keep NXP version, as it already covers the functionality for the
upstream patch [d6bbd4eea2]
- drivers/gpu/drm/imx/dw_hdmi-imx.c
- drivers/gpu/drm/imx/imx-ldb.c
- drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
Port changes from upstream commit [1a27987101], which extends
component lifetime by moving drm structures allocation/free from
bind() to probe().
- drivers/gpu/drm/imx/imx-ldb.c
Merge patch [1752ab50e8] from upstream to disable both LVDS channels
when Enoder is disabled
- drivers/mmc/host/sdhci-esdhc-imx.c
Fix merge fuzz produced by [6534c897fd].
- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
Commit d1a00c9bb1 from upstream solves the issue with improper error
reporting when qdisc type support is absent. Upstream version is merged
into NXP implementation.
- drivers/net/ethernet/freescale/enetc/enetc.c
Commit [ce06fcb6a6] from upstream merged,
base NXP version kept
- drivers/net/ethernet/freescale/enetc/enetc_pf.c
Commit [e8b86b4d87] from upstream solves
the kernel panic in case if probing fails. NXP has a clean-up logic
implemented different, where the MDIO remove would be invoked in any
failure case. Keep the NXP logic in place.
- drivers/thermal/imx_thermal.c
Upstream patch [9025a5589c] adds missing
of_node_put call, NXP version has been adapted to accommodate this patch
into the code.
- drivers/usb/cdns3/ep0.c
Manual merge of commit [be8df02707] from
upstream to protect cdns3_check_new_setup
- drivers/xen/swiotlb-xen.c
Port upstream commit cca58a1669 to NXP tree, manual hunk was
resolved during merge.
- sound/soc/fsl/fsl_esai.c
Commit [53057bd4ac] upstream addresses the problem of endless isr in
case if exception interrupt is enabled and tasklet is scheduled. Since
NXP implementation has tasklet removed with commit [2bbe95fe6c],
upstream fix does not match the main implementation, hence we keep the
NXP version here.
- sound/soc/fsl/fsl_sai.c
Apply patch [b8ae2bf5cc] from upstream, which uses FIFO watermark
mask macro.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit c6b9e95dde upstream.
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdf16d7894 upstream.
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89efbe70b2 upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27afac93e3 upstream.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c6c378b0c upstream.
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 551e553f0d upstream.
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b374c562ee upstream.
Commit 33ae787b74 ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74 ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22a82fa7d6 upstream.
The problems started with the revert (18cc7ac8a2). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a2). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e1057 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fdbe136ae ]
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8edf8eb5f upstream.
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94 ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76ed2e1057 upstream.
This reverts commit 2ae11c46d5.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8508f4cba3 ]
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b668c064e ]
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e0a851fe6b upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68e55f61c1 ]
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrey Zhizhikin