GM20B requires an extra clock compared to GK20A. Add that information
into the platform data and acquire and enable this clock if necessary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add a basic clock driver that reuses the GK20A logic.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add basic GM20B volt driver that reuses the GK20A logic.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This class supports a WFI method (0x0078) that's not present on the
KeplerChannelGpfifoA class.
The binary driver exposes both classes on these GPUs for some reason,
though there doesn't appear to be any difference in the setup that's
done for each (ie. even if you allocate GpfifoA, the WFI method will
still work).
We shall just expose GpfifoB, as I don't see a good reason to report
the presence of both.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
based on Martins initial work
v3: fix ina2x9 calculations
v4: don't kmalloc(0), fix the lsb/pga stuff
v5: add a field to tell if the power reading may be invalid
add nkvm_iccsense_read_all function
check for the device on the i2c bus
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Karol Herbst:
v4: don't kmalloc(0)
v5: stricter validation
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Add secure boot support for the GM20B chip found in Tegra X1. Secure
boot on Tegra works slightly differently from desktop, notably in the
way the WPR region is set up.
In addition, the firmware bootloaders use a slightly different header
format.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add secure-boot for the dGPU set of GM20X chips, using the PMU as the
high-secure falcon.
This work is based on Deepak Goyal's initial port of Secure Boot to
Nouveau.
v2. use proper memory target function
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On GM200 and later GPUs, firmware for some essential falcons (notably
GR ones) must be authenticated by a NVIDIA-produced signature and
loaded by a high-secure falcon in order to be able to access privileged
registers, in a process known as Secure Boot.
Secure Boot requires building a binary blob containing the firmwares
and signatures of the falcons to be loaded. This blob is then given to
a high-secure falcon running a signed loader firmware that copies the
blob into a write-protected region, checks that the signatures are
valid, and finally loads the verified firmware into the managed falcons
and switches them to privileged mode.
This patch adds infrastructure code to support this process on chips
that require it.
v2:
- The IRQ mask of the PMU falcon was left - replace it with the proper
irq_mask variable.
- The falcon reset procedure expecting a falcon in an initialized state,
which was accidentally provided by the PMU subdev. Make sure that
secboot can manage the falcon on its own.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add memcpy functions to copy a buffer to a gpuobj and vice-versa. This
will be used by the secure boot code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Most of the per-chipset differences will go away when we fully switch
to using the register lists provided by the firmware files, which will
leave all the remaining code "belonging" to GM200.
This is a preemptive rename from GM204 to GM200.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add two functions nvkm_firmware_get() and nvkm_firmware_put() to load a
firmware file and free its resources, respectively. Since firmware files
are becoming a necessity for new GPUs, and their location has been
standardized to nvidia/chip/, this will prevent duplicate and
error-prone name-generation code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
v2: rename and group functions
v4: change copyright information
move printing of pcie speeds into oneinit,
rename all pcie functions to nvkm_pcie_*
don't try to raise the pcie version when no higher one is supported
v5: revert Copyright changes and rename nvkm_pcie_raise_version to nvkm_pcie_set_version
v6: remove some useless pci_is_pcie checks and rework messages
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
NVIDIA have indicated that the workaround is required on all GK10[467]
boards that have the PGOB fuse set.
I've left the commandline option in place for now, as paranoia.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
No locking is required for the traversal of this list, as it only
happens during suspend/resume where nothing else can be executing.
Fixes some of the issues noticed during parallel piglit runs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
