commit efd597b283 upstream.
The power-down mask of the ad5504 is actually a power-up mask. Meaning if
a bit is set the corresponding channel is powered up and if it is not set
the channel is powered down.
The driver currently has this the wrong way around, resulting in the
channel being powered up when requested to be powered down and vice versa.
Fixes: 3bbbf150ff ("staging:iio:dac:ad5504: Use strtobool for boolean values")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201209104649.5794-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f9bce7a22 upstream
If we are using edge IRQs, new samples can arrive while processing
current interrupt since there are no hw guarantees the irq line
stays "low" long enough to properly detect the new interrupt.
In this case the new sample will be missed.
Polling FIFO status register in st_lsm6dsx_handler_thread routine
allow us to read new samples even if the interrupt arrives while
processing previous data and the timeslot where the line is "low"
is too short to be properly detected.
Fixes: 89ca88a7cd ("iio: imu: st_lsm6dsx: support active-low interrupts")
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/5e93cda7dc1e665f5685c53ad8e9ea71dbae782d.1605378871.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[sudip: manual backport to old irq handler path]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b6b51234d upstream
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable array in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver, depending on which channels are enabled, the timestamp
can be in a number of locations. Hence we cannot use a structure
to specify the data layout without it being misleading.
Fixes: 77c4ad2d6a ("iio: imu: Add initial support for Bosch BMI160")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-6-jic23@kernel.org
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e405bc251 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc() so no
data can leak apart from previous readings.
In this driver the timestamp can end up in various different locations
depending on what other channels are enabled. As a result, we don't
use a structure to specify it's position as that would be misleading.
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-9-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0bd27f02d upstream.
The buffer is expressed as a u32 array, yet the extra space for
the s64 timestamp was expressed as sizeof(s64)/sizeof(u16).
This will result in 2 extra u32 elements.
Fix by dividing by sizeof(u32).
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Jonathan Cameron<Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-8-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7de42d6b upstream.
The comment implies this device has 3 sensor types, but it only
has an accelerometer and a gyroscope (both 3D). As such the
buffer does not need to be as long as stated.
Note I've separated this from the following patch which fixes
the alignment for passing to iio_push_to_buffers_with_timestamp()
as they are different issues even if they affect the same line
of code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Daniel Baluta <daniel.baluta@oss.nxp.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-5-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198cf32f05 upstream.
Whilst this is another case of the issue Lars reported with
an array of elements of smaller than 8 bytes being passed
to iio_push_to_buffers_with_timestamp(), the solution here is
a bit different from the other cases and relies on __aligned
working on the stack (true since 4.6?)
This one is unusual. We have to do an explicit memset() each time
as we are reading 3 bytes into a potential 4 byte channel which
may sometimes be a 2 byte channel depending on what is enabled.
As such, moving the buffer to the heap in the iio_priv structure
doesn't save us much. We can't use a nice explicit structure
on the stack either as the data channels have different storage
sizes and are all separately controlled.
Fixes: cc26ad455f ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-7-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89deb13342 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc() so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case but
does make the code slightly less fragile so I have included it.
Fixes: 39631b5f95 ("iio: Add Freescale mag3110 magnetometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-4-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d837a996f5 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv()
This data is allocated with kzalloc() so no data can leak apart
from previous readings.
A local unsigned int variable is used for the regmap call so it
is clear there is no potential issue with writing into the padding
of the structure.
Fixes: 3025c8688c ("iio: light: add support for UVIS25 sensor")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-3-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a61817216b upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc() so no data can leak apart
from previous readings and in this case the status byte from the device.
The forced alignment of ts is not necessary in this case but it
potentially makes the code less fragile.
>From personal communications with Mikko:
We could probably split the reading of the int register, but it
would mean a significant performance cost of 20 i2c clock cycles.
Fixes: e12ffd241c ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200920112742.170751-2-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 560c6b914c upstream.
Fix the missing clk_disable_unprepare() of info->pclk
before return from rockchip_saradc_resume in the error
handling case when fails to prepare and enable info->clk.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Fixes: 44d6f2ef94 ("iio: adc: add driver for Rockchip saradc")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201103120743.110662-1-miaoqinglang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ef7b70ca upstream.
When updating the buffer demux, we will skip a scan element from the
device in the case `in_ind != out_ind` and we enter the while loop.
in_ind should only be refreshed with `find_next_bit()` in the end of the
loop.
Note, to cause problems we need a situation where we are skippig over
an element (channel not enabled) that happens to not have the same size
as the next element. Whilst this is a possible situation we haven't
actually identified any cases in mainline where it happens as most drivers
have consistent channel storage sizes with the exception of the timestamp
which is the last element and hence never skipped over.
Fixes: 5ada4ea9be ("staging:iio: add demux optionally to path from device to buffer")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20201112144323.28887-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0178297c1e ]
On PREEMPT_RT enabled kernels unmarked hrtimers are moved into soft
interrupt expiry mode by default.
The IIO hrtimer-trigger needs to run in hard interrupt context since it
will end up calling generic_handle_irq() which has the requirement to run
in hard interrupt context.
Explicitly specify that the timer needs to run in hard interrupt context by
using the HRTIMER_MODE_REL_HARD flag.
Fixes: f5c2f0215e ("hrtimer: Move unmarked hrtimers to soft interrupt expiry on RT")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20201117103751.16131-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 15207a92e0 upstream.
dev_comp field is used in a couple of places but it is never set. This
results in kernel oops when dereferencing a NULL pointer. Set the
`dev_comp` field correctly in the probe function.
Fixes: 6d97024dce ("iio: adc: mediatek: mt6577-auxadc, add mt6765 support")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201018194644.3366846-1-fparent@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b1032a65 upstream.
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 KXCJ91008-s
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read by a special HingeAngleService
process; and this process calls a DSM (Device Specific Method) on the
ACPI KIOX010A device node for the sensor in the display, to let the
embedded-controller (EC) know about the mode so that it can disable the
kbd and touchpad to avoid spurious input while folded into tablet-mode.
This notifying of the EC is problematic because sometimes the EC comes up
thinking that device is in tablet-mode and the kbd and touchpad do not
work. This happens for example on Irbis NB111 devices after a suspend /
resume cycle (after a complete battery drain / hard reset without having
booted Windows at least once). Other 2-in-1s which are likely affected
too are e.g. the Teclast F5 and F6 series.
The kxcjk-1013 driver may seem like a strange place to deal with this,
but since it is *the* driver for the ACPI KIOX010A device, it is also
the driver which has access to the ACPI handle needed by the DSM.
Add support for calling the DSM and on probe unconditionally tell the
EC that the device is laptop mode, fixing the kbd and touchpad sometimes
not working.
Fixes: 7f6232e695 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-3-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11e94f28c3 upstream.
Replace the boolean is_smo8500_device variable with an acpi_type enum.
For now this can be either ACPI_GENERIC or ACPI_SMO8500, this is a
preparation patch for adding special handling for the KIOX010A ACPI HID,
which will add a ACPI_KIOX010A acpi_type to the introduced enum.
For stable as needed as precursor for next patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 7f6232e695 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-2-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44a146a44f upstream.
When VCNL4035 is enabled and IIO_BUFFER is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_TRIGGERED_BUFFER
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- VCNL4035 [=y] && IIO [=y] && I2C [=y]
The reason is that VCNL4035 selects IIO_TRIGGERED_BUFFER without depending
on or selecting IIO_BUFFER while IIO_TRIGGERED_BUFFER depends on
IIO_BUFFER. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: 55707294c4 ("iio: light: Add support for vishay vcnl4035")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209883
Link: https://lore.kernel.org/r/20201102223523.572461-1-fazilyildiran@gmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10ab7cfd55 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
This is fixed by using an explicit c structure. As there are no
holes in the structure, there is no possiblity of data leakage
in this case.
The explicit alignment of ts is not strictly necessary but potentially
makes the code slightly less fragile. It also removes the possibility
of this being cut and paste into another driver where the alignment
isn't already true.
Fixes: 36e0371e77 ("iio:itg3200: Use iio_push_to_buffers_with_timestamp()")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-6-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 293e809b2e upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
We move to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. Note that previously
no leak at all could occur, but previous readings should never
be a problem.
In this case the timestamp location depends on what other channels
are enabled. As such we can't use a structure without misleading
by suggesting only one possible timestamp location.
Fixes: 50a6edb1b6 ("iio: adc: add ADC12130/ADC12132/ADC12138 ADC driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-26-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39e91f3be4 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
We fix this issues by moving to a suitable structure in the iio_priv()
data with alignment explicitly requested. This data is allocated
with kzalloc so no data can leak apart from previous readings.
Note that previously no data could leak 'including' previous readings
but I don't think it is an issue to potentially leak them like
this now does.
In this case the postioning of the timestamp is depends on what
other channels are enabled. As such we cannot use a structure to
make the alignment explicit as it would be missleading by suggesting
only one possible location for the timestamp.
Fixes: 815bbc8746 ("iio: ti-adc0832: add triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-25-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da4410d407 upstream.
Add missing of_node_put calls when exiting the for_each_child_of_node
loop in rcar_gyroadc_parse_subdevs early.
Also add goto-exception handling for the error paths in that loop.
Fixes: 059c53b323 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: Tobias Jordan <kernel@cdqe.de>
Link: https://lore.kernel.org/r/20200926161946.GA10240@agrajag.zerfleddert.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0456ecf34d upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 24 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable array in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
Depending on the enabled channels, the location of the timestamp
can be at various aligned offsets through the buffer. As such we
any use of a structure to enforce this alignment would incorrectly
suggest a single location for the timestamp. Comments adjusted to
express this clearly in the code.
Fixes: ac45e57f15 ("iio: light: Add driver for Silabs si1132, si1141/2/3 and si1145/6/7 ambient light, uv index and proximity sensors")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200722155103.979802-9-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c537d34575 ]
When the ADC is runtime suspended and starting a conversion, the stm32-adc
driver calls pm_runtime_get_sync() that gets cascaded to the parent
(e.g. runtime resume of stm32-adc-core driver). This also kicks the
autosuspend delay (e.g. 2s) of the parent.
Once the ADC is active, calling pm_runtime_get_sync() again (upon a new
capture) won't kick the autosuspend delay for the parent (stm32-adc-core
driver) as already active.
Currently, this makes the stm32-adc-core driver go in suspend state
every 2s when doing slow polling. As an example, doing a capture, e.g.
cat in_voltageY_raw at a 0.2s rate, the auto suspend delay for the parent
isn't refreshed. Once it expires, the parent immediately falls into
runtime suspended state, in between two captures, as soon as the child
driver falls into runtime suspend state:
- e.g. after 2s, + child calls pm_runtime_put_autosuspend() + 100ms
autosuspend delay of the child.
- stm32-adc-core switches off regulators, clocks and so on.
- They get switched on back again 100ms later in this example (at 2.2s).
So, use runtime_idle() callback in stm32-adc-core driver to call
pm_runtime_mark_last_busy() for the parent driver (stm32-adc-core),
to avoid this.
Fixes: 9bdbb1139c ("iio: adc: stm32-adc: add power management support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/1593615328-5180-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 89226a296d upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack. As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The additional forcing of the 8 byte alignment of the timestamp
is not strictly necessary but makes the code less fragile by
making this explicit.
Fixes: c7eeea93ac ("iio: Add Freescale MMA8452Q 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e5ac1f220 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte u8 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
The force alignment of ts is not strictly necessary in this particularly
case but does make the code less fragile.
Fixes: a84ef0d181 ("iio: accel: add Freescale MMA7455L/MMA7456L 3-axis accelerometer driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95ad67577d upstream.
iio_push_to_buffers_with_timestamp assumes 8 byte alignment which
is not guaranteed by an array of smaller elements.
Note that whilst in this particular case the alignment forcing
of the ts element is not strictly necessary it acts as good
documentation. Doing this where not necessary should cut
down on the number of cut and paste introduced errors elsewhere.
Fixes: 0427a106a9 ("iio: accel: kxsd9: Add triggered buffer handling")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb1a148ef4 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
The explicit alignment of ts is necessary to ensure consistent
padding for x86_32 in which the ts would otherwise be 4 byte aligned.
Fixes: 283d26917a ("iio: chemical: ccs811: Add triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 523628852a upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak appart
from previous readings.
It is necessary to force the alignment of ts to avoid the padding
on x86_32 being different from 64 bit platorms (it alows for
4 bytes aligned 8 byte types.
Fixes: 06ad7ea10e ("max44000: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02ad21cefb upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case as by
coincidence the padding will end up the same, however I consider
it to make the code less fragile and have included it.
Fixes: bc11ca4a0b ("iio:magnetometer:ak8975: triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54f82df2ba upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
Fixes: 08e05d1fce ("ti-adc081c: Initial triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db8f06d97e upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The explicit alignment of ts is necessary to ensure correct padding
on architectures where s64 is only 4 bytes aligned such as x86_32.
Fixes: a9e9c7153e ("iio: adc: add max1117/max1118/max1119 ADC driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8cd222feb upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Fixes: c43a102e67 ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a661b571e3 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The force alignment of ts is not strictly necessary in this case
but reduces the fragility of the code.
Fixes: 3691e5a694 ("iio: adc: add driver for the ti-adc084s021 chip")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6f86f7243 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by moving
to a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
Fixes tag is beyond some major refactoring so likely manual backporting
would be needed to get that far back.
Whilst the force alignment of the ts is not strictly necessary, it
does make the code less fragile.
Fixes: 3bbec97733 ("iio: bmc150_accel: add support for hardware fifo")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f60e8bb842 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 16 byte s16 array on the stack As Lars also noted
this anti pattern can involve a leak of data to userspace and that
indeed can happen here. We close both issues by moving to
a suitable structure in the iio_priv() data with alignment
ensured by use of an explicit c structure. This data is allocated
with kzalloc so no data can leak appart from previous readings.
In this case the forced alignment of the ts is necessary to ensure
correct padding on x86_32 where the s64 would only be 4 byte aligned.
Fixes: 16b0526153 ("mb1232.c: add distance iio sensor with i2c")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2684d50034 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here we use a structure on the stack. The driver already did an
explicit memset so no data leak was possible.
Forced alignment of ts is not strictly necessary but probably makes
the code slightly less fragile.
Note there has been some rework in this driver of the years, so no
way this will apply cleanly all the way back.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 336306790b upstream.
BMI160 Minimium gyroscope frequency in normal mode is 25Hz.
When older EC firmware do not report their sensors frequencies,
use 25Hz as the minimum for gyroscope to be sure it works on BMI160.
Fixes: ae7b02ad2f ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e71e6dbe96 upstream.
To stop conversion ads1015_set_power_state() function call unimplemented
function __pm_runtime_suspend() from pm_runtime_put_autosuspend()
if CONFIG_PM is not set.
In case of CONFIG_PM is not set: __pm_runtime_suspend() returns -ENOSYS,
so ads1015_read_raw() failed because ads1015_set_power_state() returns an
error.
If CONFIG_PM is disabled, there is no need to start/stop conversion.
Fix it by adding return 0 function variant if CONFIG_PM is not set.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes: ecc24e72f4 ("iio: adc: Add TI ADS1015 ADC driver support")
Tested-by: Maxim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f1093d83d upstream.
Locking should be held for the entire reading sequence involving setting
the channel, waiting for the channel switch and reading from the
channel.
If not, reading from a channel can result mixing with the reading from
another channel.
Fixes: 07914c84ba ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200819075525.1395248-1-angelo.compagnucci@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a139ffa40f ]
Reading from the chip should be unlocked on error path else the lock
could never being released.
Fixes: 07914c84ba ("iio: adc: Add driver for Microchip MCP3422/3/4 high resolution ADC")
Fixes: 3f1093d83d ("iio: adc: mcp3422: fix locking scope")
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Link: https://lore.kernel.org/r/20200901093218.1500845-1-angelo.compagnucci@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 65afb0932a upstream.
There are 2 exit paths where the lock isn't held, but try to unlock the
mutex when exiting. In these places we should just return from the
function.
A neater approach would be to cleanup the ad5592r_read_raw(), but that
would make this patch more difficult to backport to stable versions.
Fixes 56ca9db862bf3: ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Reported-by: Charles Stanhope <charles.stanhope@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0536f9826 ]
If 'ad7780_init_gpios()' fails, we must not release some resources that
have not been allocated yet. Return directly instead.
Fixes: 5bb30e7daf ("staging: iio: ad7780: move regulator to after GPIO init")
Fixes: 9085daa4ab ("staging: iio: ad7780: add gain & filter gpio support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f88ecccac4 ]
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 40 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
Fixes: 87aec56e27 ("iio: health: Add driver for the TI AFE4404 heart monitor")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3f9c6d3879 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak appart from previous readings.
Fixes: eec96d1e2d ("iio: health: Add driver for the TI AFE4403 heart monitor")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8db4afe163 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
Here there is no data leak possibility so use an explicit structure
on the stack to ensure alignment and nice readable fashion.
The forced alignment of ts isn't strictly necessary in this driver
as the padding will be correct anyway (there isn't any). However
it is probably less fragile to have it there and it acts as
documentation of the requirement.
Fixes: 713bbb4efb ("iio: pressure: ms5611: Add triggered buffer support")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tomasz Duszynski <tomasz.duszynski@octakon.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c49056ad9 upstream.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak
apart from previous readings.
Explicit alignment of ts needed to ensure consistent padding
on all architectures (particularly x86_32 with it's 4 byte alignment
of s64)
Fixes: e4a70e3e7d ("iio: humidity: add support to hts221 rh/temp combo device")
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7369ae1f4 upstream.
The function iio_device_register() was called in mma8452_probe().
But the function iio_device_unregister() was not called after
a call of the function mma8452_set_freefall_mode() failed.
Thus add the missed function call for one error case.
Fixes: 1a965d405f ("drivers:iio:accel:mma8452: added cleanup provision in case of failure.")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen