This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, mm: Add an initial page table for core bootstrapping
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb,debug_core: adjust master cpu switch logic against new debug_core locking
debug_core: refactor locking for master/slave cpus
x86,kgdb: remove unnecessary call to kgdb_correct_hw_break()
debug_core: disable hw_breakpoints on all cores in kgdb_cpu_enter()
kdb,kgdb: fix sparse fixups
kdb: Fix oops in kdb_unregister
kdb,ftdump: Remove reference to internal kdb include
kdb: Allow kernel loadable modules to add kdb shell functions
debug_core: stop rcu warnings on kernel resume
debug_core: move all watch dog syncs to a single function
x86,kgdb: fix debugger hw breakpoint test regression in 2.6.35
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (31 commits)
driver core: Display error codes when class suspend fails
Driver core: Add section count to memory_block struct
Driver core: Add mutex for adding/removing memory blocks
Driver core: Move find_memory_block routine
hpilo: Despecificate driver from iLO generation
driver core: Convert link_mem_sections to use find_memory_block_hinted.
driver core: Introduce find_memory_block_hinted which utilizes kset_find_obj_hinted.
kobject: Introduce kset_find_obj_hinted.
driver core: fix build for CONFIG_BLOCK not enabled
driver-core: base: change to new flag variable
sysfs: only access bin file vm_ops with the active lock
sysfs: Fail bin file mmap if vma close is implemented.
FW_LOADER: fix kconfig dependency warning on HOTPLUG
uio: Statically allocate uio_class and use class .dev_attrs.
uio: Support 2^MINOR_BITS minors
uio: Cleanup irq handling.
uio: Don't clear driver data
uio: Fix lack of locking in init_uio_class
SYSFS: Allow boot time switching between deprecated and modern sysfs layout
driver core: remove CONFIG_SYSFS_DEPRECATED_V2 but keep it for block devices
...
Commit dd3932eddf ("block: remove BLKDEV_IFL_WAIT") had removed the
flag argument to blkdev_issue_flush(), but the ocfs2 merge brought in a
new one. It didn't cause a merge conflict, so the merges silently
worked out fine, but the result didn't actually compile.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (56 commits)
[CIFS] move close processing from cifs_close to cifsFileInfo_put
cifs: convert cifs_tcp_ses_lock from a rwlock to a spinlock
cifs: cancel_delayed_work() + flush_scheduled_work() -> cancel_delayed_work_sync()
Clean up two declarations of blob_len
cifs: move cifsFileInfo_put to file.c
cifs: convert GlobalSMBSeslock from a rwlock to regular spinlock
[CIFS] Fix minor checkpatch warning and update cifs version
cifs: move cifs_new_fileinfo to file.c
cifs: eliminate pfile pointer from cifsFileInfo
cifs: cifs_write argument change and cleanup
cifs: clean up cifs_reopen_file
cifs: eliminate the inode argument from cifs_new_fileinfo
cifs: eliminate oflags option from cifs_new_fileinfo
cifs: fix flags handling in cifs_posix_open
cifs: eliminate cifs_posix_open_inode_helper
cifs: handle FindFirst failure gracefully
NTLM authentication and signing - Calculate auth response per smb session
cifs: don't use vfsmount to pin superblock for oplock breaks
cifs: keep dentry reference in cifsFileInfo instead of inode reference
cifs: on multiuser mount, set ownership to current_fsuid/current_fsgid (try #7)
...
Fix up trivial conflict in fs/cifs/cifsfs.c due to added/removed header files
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: Fix dlm lock status block comment in dlm.h
dlm: Don't send callback to node making lock request when "try 1cb" fails
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (36 commits)
xfs: semaphore cleanup
xfs: Extend project quotas to support 32bit project ids
xfs: remove xfs_buf wrappers
xfs: remove xfs_cred.h
xfs: remove xfs_globals.h
xfs: remove xfs_version.h
xfs: remove xfs_refcache.h
xfs: fix the xfs_trans_committed
xfs: remove unused t_callback field in struct xfs_trans
xfs: fix bogus m_maxagi check in xfs_iget
xfs: do not use xfs_mod_incore_sb_batch for per-cpu counters
xfs: do not use xfs_mod_incore_sb for per-cpu counters
xfs: remove XFS_MOUNT_NO_PERCPU_SB
xfs: pack xfs_buf structure more tightly
xfs: convert buffer cache hash to rbtree
xfs: serialise inode reclaim within an AG
xfs: batch inode reclaim lookup
xfs: implement batched inode lookups for AG walking
xfs: split out inode walk inode grabbing
xfs: split inode AG walking into separate code for reclaim
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: update comments to reflect that percpu allocations are always zero-filled
percpu: Optimize __get_cpu_var()
x86, percpu: Optimize this_cpu_ptr
percpu: clear memory allocated with the km allocator
percpu: fix build breakage on s390 and cleanup build configuration tests
percpu: use percpu allocator on UP too
percpu: reduce PCPU_MIN_UNIT_SIZE to 32k
vmalloc: pcpu_get/free_vm_areas() aren't needed on UP
Fixed up trivial conflicts in include/linux/percpu.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove in_workqueue_context()
workqueue: Clarify that schedule_on_each_cpu is synchronous
memory_hotplug: drop spurious calls to flush_scheduled_work()
shpchp: update workqueue usage
pciehp: update workqueue usage
isdn/eicon: don't call flush_scheduled_work() from diva_os_remove_soft_isr()
workqueue: add and use WQ_MEM_RECLAIM flag
workqueue: fix HIGHPRI handling in keep_working()
workqueue: add queue_work and activate_work trace points
workqueue: prepare for more tracepoints
workqueue: implement flush[_delayed]_work_sync()
workqueue: factor out start_flush_work()
workqueue: cleanup flush/cancel functions
workqueue: implement alloc_ordered_workqueue()
Fix up trivial conflict in fs/gfs2/main.c as per Tejun
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
xen-blkfront: disable barrier/flush write support
Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
block: remove BLKDEV_IFL_WAIT
aic7xxx_old: removed unused 'req' variable
block: remove the BH_Eopnotsupp flag
block: remove the BLKDEV_IFL_BARRIER flag
block: remove the WRITE_BARRIER flag
swap: do not send discards as barriers
fat: do not send discards as barriers
ext4: do not send discards as barriers
jbd2: replace barriers with explicit flush / FUA usage
jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
jbd: replace barriers with explicit flush / FUA usage
nilfs2: replace barriers with explicit flush / FUA usage
reiserfs: replace barriers with explicit flush / FUA usage
gfs2: replace barriers with explicit flush / FUA usage
btrfs: replace barriers with explicit flush / FUA usage
xfs: replace barriers with explicit flush / FUA usage
block: pass gfp_mask and flags to sb_issue_discard
dm: convey that all flushes are processed as empty
...
* 'for-2.6.37/drivers' of git://git.kernel.dk/linux-2.6-block: (95 commits)
cciss: fix PCI IDs for new Smart Array controllers
drbd: add race-breaker to drbd_go_diskless
drbd: use dynamic_dev_dbg to optionally log uuid changes
dynamic_debug.h: Fix dynamic_dev_dbg() macro if CONFIG_DYNAMIC_DEBUG not set
drbd: cleanup: change "<= 0" to "== 0"
drbd: relax the grace period of the md_sync timer again
drbd: add some more explicit drbd_md_sync
drbd: drop wrong debug asserts, fix recently introduced race
drbd: cleanup useless leftover warn/error printk's
drbd: add explicit drbd_md_sync to drbd_resync_finished
drbd: Do not log an ASSERT for P_OV_REQUEST packets while C_CONNECTED
drbd: fix for possible deadlock on IO error during resync
drbd: fix unlikely access after free and list corruption
drbd: fix for spurious fullsync (uuids rotated too fast)
drbd: allow for explicit resync-finished notifications
drbd: preparation commit, using full state in receive_state()
drbd: drbd_send_ack_dp must not rely on header information
drbd: Fix regression in recv_bm_rle_bits (compressed bitmap)
drbd: Fixed a stupid copy and paste error
drbd: Allow larger values for c-fill-target.
...
Fix up trivial conflict in drivers/block/ataflop.c due to BKL removal
* 'for-2.6.37/core' of git://git.kernel.dk/linux-2.6-block: (39 commits)
cfq-iosched: Fix a gcc 4.5 warning and put some comments
block: Turn bvec_k{un,}map_irq() into static inline functions
block: fix accounting bug on cross partition merges
block: Make the integrity mapped property a bio flag
block: Fix double free in blk_integrity_unregister
block: Ensure physical block size is unsigned int
blkio-throttle: Fix possible multiplication overflow in iops calculations
blkio-throttle: limit max iops value to UINT_MAX
blkio-throttle: There is no need to convert jiffies to milli seconds
blkio-throttle: Fix link failure failure on i386
blkio: Recalculate the throttled bio dispatch time upon throttle limit change
blkio: Add root group to td->tg_list
blkio: deletion of a cgroup was causes oops
blkio: Do not export throttle files if CONFIG_BLK_DEV_THROTTLING=n
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: revert bad fix for memory hotplug causing bounces
Fix compile error in blk-exec.c for !CONFIG_DETECT_HUNG_TASK
block: set the bounce_pfn to the actual DMA limit rather than to max memory
block: Prevent hang_check firing during long I/O
cfq: improve fsync performance for small files
...
Fix up trivial conflicts due to __rcu sparse annotation in include/linux/genhd.h
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: tighten the corrupted PEB criteria
UBI: fix check_data_ff return code
UBI: remember copy_flag while scanning
UBI: preserve corrupted PEBs
UBI: add truly corrupted PEBs to corrupted list
UBI: introduce debugging helper function
UBI: make check_pattern function non-static
UBI: do not put eraseblocks to the corrupted list unnecessarily
UBI: separate out corrupted list
UBI: change cascade of ifs to switch statements
UBI: rename a local variable
UBI: handle bit-flips when no header found
UBI: remove duplicate IO error codes
UBI: rename IO error code
UBI: fix small 80 characters limit style issue
UBI: cleanup and simplify Kconfig
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: do not allocate unneeded scan buffer
UBIFS: do not forget to cancel timers
UBIFS: remove a bit of unneeded code
UBIFS: add a commentary about log recovery
UBIFS: avoid kernel error if ubifs superblock read fails
UBIFS: introduce new flags for RO mounts
UBIFS: introduce new flag for RO due to errors
UBIFS: check return code of pnode_lookup
UBIFS: check return code of ubifs_lpt_lookup
UBIFS: improve error reporting when reading bad node
UBIFS: introduce list sorting debugging checks
UBIFS: fix assertion warnings in comparison function
UBIFS: mark unused key objects as invalid
UBIFS: do not write rubbish into truncation scanning node
UBIFS: improve assertion in node comparison functions
UBIFS: do not use key type in list_sort
UBIFS: do not look up truncation nodes
UBIFS: fix assertion warning
UBIFS: do not treat ENOSPC specially
UBIFS: switch to RO mode after synchronizing
The kdb shell needs to enforce switching back to the original CPU that
took the exception before restoring normal kernel execution. Resuming
from a different CPU than what took the original exception will cause
problems with spin locks that are freed from the a different processor
than had taken the lock.
The special logic in dbg_cpu_switch() can go away entirely with
because the state of what cpus want to be masters or slaves will
remain unchanged between entry and exit of the debug_core exception
context.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
For quite some time there have been problems with memory barriers and
various races with NMI on multi processor systems using the kernel
debugger. The algorithm for entering the kernel debug core and
resuming kernel execution was racy and had several known edge case
problems with attempting to debug something on a heavily loaded system
using breakpoints that are hit repeatedly and quickly.
The prior "locking" design entry worked as follows:
* The atomic counter kgdb_active was used with atomic exchange in
order to elect a master cpu out of all the cpus that may have
taken a debug exception.
* The master cpu increments all elements of passive_cpu_wait[].
* The master cpu issues the round up cpus message.
* Each "slave cpu" that enters the debug core increments its own
element in cpu_in_kgdb[].
* Each "slave cpu" spins on passive_cpu_wait[] until it becomes 0.
* The master cpu debugs the system.
The new scheme removes the two arrays of atomic counters and replaces
them with 2 single counters. One counter is used to count the number
of cpus waiting to become a master cpu (because one or more hit an
exception). The second counter is use to indicate how many cpus have
entered as slave cpus.
The new entry logic works as follows:
* One or more cpus enters via kgdb_handle_exception() and increments
the masters_in_kgdb. Each cpu attempts to get the spin lock called
dbg_master_lock.
* The master cpu sets kgdb_active to the current cpu.
* The master cpu takes the spinlock dbg_slave_lock.
* The master cpu asks to round up all the other cpus.
* Each slave cpu that is not already in kgdb_handle_exception()
will enter and increment slaves_in_kgdb. Each slave will now spin
try_locking on dbg_slave_lock.
* The master cpu waits for the sum of masters_in_kgdb and slaves_in_kgdb
to be equal to the sum of the online cpus.
* The master cpu debugs the system.
In the new design the kgdb_active can only be changed while holding
dbg_master_lock. Stress testing has not turned up any further
entry/exit races that existed in the prior locking design. The prior
locking design suffered from atomic variables not being truly atomic
(in the capacity as used by kgdb) along with memory barrier races.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
The kernel debug_core invokes hw breakpoint install and removal via
call backs. The architecture specific kgdb stubs only need to
implement the call backs and not actually call the functions.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: x86@kernel.org
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
The slave cpus do not have the hw breakpoints disabled upon entry to
the debug_core and as a result could cause unrecoverable recursive
faults on badly placed breakpoints, or get out of sync with the arch
specific hw breakpoint operations.
This patch addresses the problem by invoking kgdb_disable_hw_debug()
earlier in kgdb_enter_cpu for each cpu that enters the debug core.
The hw breakpoint dis/enable flow should be:
master_debug_cpu slave_debug_cpu
\ /
kgdb_cpu_enter
|
kgdb_disable_hw_debug --> uninstall pre-enabled hw_breakpoint
|
do add/rm dis/enable operates to hw_breakpoints on master_debug_cpu..
|
correct_hw_break --> correct/install the enabled hw_breakpoint
|
leave_kgdb
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Fix the following sparse warnings:
kdb_main.c:328:5: warning: symbol 'kdbgetu64arg' was not declared. Should it be static?
kgdboc.c:246:12: warning: symbol 'kgdboc_early_init' was not declared. Should it be static?
kgdb.c:652:26: warning: incorrect type in argument 1 (different address spaces)
kgdb.c:652:26: expected void const *ptr
kgdb.c:652:26: got struct perf_event *[noderef] <asn:3>*pev
The one in kgdb.c required the (void * __force) because of the return
code from register_wide_hw_breakpoint looking like:
return (void __percpu __force *)ERR_PTR(err);
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Nothing should try to use kdb_commands directly as sometimes it is
null. Instead, use the for_each_kdbcmd() iterator.
This particular problem dates back to the initial kdb merge (2.6.35),
but at that point nothing was dynamically unregistering commands from
the kdb shell.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Now that include/linux/kdb.h properly exports all the functions
required to dynamically add a kdb shell command, the reference to the
private kdb header can be removed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
In order to allow kernel modules to dynamically add a command to the
kdb shell the kdb_register, kdb_register_repeat, kdb_unregister, and
kdb_printf need to be exported as GPL symbols.
Any kernel module that adds a dynamic kdb shell function should only
need to include linux/kdb.h.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When returning from the kernel debugger reset the rcu jiffies_stall
value to prevent the rcu stall detector from sending NMI events which
invoke a stack dump for each cpu in the system.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Move the various clock and watch dog syncs to a single function in
advance of adding another sync for the rcu stall detector.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
HW breakpoints events stopped working correctly with kgdb as a result
of commit: 018cbffe68 (Merge commit
'v2.6.33' into perf/core), later commit:
ba773f7c51 (x86,kgdb: Fix hw breakpoint
regression) allowed breakpoints to propagate to the debugger core but
did not completely address the original regression in functionality
found in 2.6.35.
When the DR_STEP flag is set in dr6 along with any of the DR_TRAP
bits, the kgdb exception handler will enter once from the
hw_breakpoint API call back and again from the die notifier for
do_debug(), which causes the debugger to stop twice and also for the
kgdb regression tests to fail running under kvm with:
echo V2I1 > /sys/module/kgdbts/parameters/kgdbts
To address the problem, the kgdb overflow handler needs to implement
the same logic as the ptrace overflow handler call back with respect
to updating the virtual copy of dr6. This will allow the kgdb
do_debug() die notifier to properly handle the exception and the
attached debugger, or kgdb test suite, will only receive a single
notification.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: x86@kernel.org
Start unifying the PPI/EPPI peripheral structures in one place. This
may be used by camera/video/fpga/high speed devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This matches all the other Blackfin ports and keep us from having to write
bf561-specific code in many places.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common 8250 serial driver supports an "irqflags" field,
we don't need to patch in a custom define into the code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Different arches use different names, so make sure we define both so
common code (like MTD_XIP) "just works".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mainline version of git merged support for Blackfin parts, but we now
need to propagate the gcc arch define to make it work.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have to use ioctl numbers that don't collide with common code.
Otherwise, these ones never even get called because the common fs
code swalled all invocations.
Reported-by: Kay Duenzer <kduenzer@maku.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
