In the discussion for this set of patches [link below], Bjorn Helgaas
pointed out that the ACPI HEST AER error sources do not have the PCIe
segment number associated with the bus. I worked with the ACPI spec and
got this change to definition of the "Bus" field into the recently released
ACPI Spec 5.0a section 18.3.2.3-5:
Identifies the PCI Bus and Segment of the device. The Bus is encoded in
bits 0-7. For systems that expose multiple PCI segment groups, the
segment number is encoded in bits 8-23 and bits 24-31 must be zero. For
systems that do not expose multiple PCI segment groups, bits 8-31 must be
zero. If the GLOBAL flag is specified, this field is ignored.
This patch makes use of the new definition in the only place in the kernel
that uses the acpi_hest_aer_common's bus field.
This depends on 36f3615152 ("ACPICA: Add helper macros to extract
bus/segment numbers from HEST table.")
Link: http://lkml.kernel.org/r/1370542251-27387-1-git-send-email-betty.dall@hp.com
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of 3e1b16002a ("ACPI/PCI: PCIe ASPM _OSC support
capabilities called when root bridge added"), removing this interface:
pcie_aspm_enabled()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andrew Patterson <andrew.patterson@hp.com>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Previously pcie_device_init() called get_device() if device_register() for
the new pcie_device succeeded, and remove_iter() called put_device() when
removing before unregistering the device.
But device_register() already increments the reference count in
device_add(), so we don't need to do it again here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is required so that we give up the last reference to the device.
Removed the kfree() as put_device will result in release_pcie_device()
being called and hence the container of the device will be kfree'd.
[bhelgaas: fix conflict after my previous cleanup]
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the straightline path the normal no-error path. Check for errors and
return them directly, instead of checking for success and putting the
normal path in an "if" body.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_hest_parse() and aer_hest_parse_aff() are almost identical. We use
aer_hest_parse() to check the ACPI_HEST_FIRMWARE_FIRST flag for a specific
device, and we use aer_hest_parse_aff() to check to see if any device sets
the flag.
This drops aer_hest_parse_aff() and enhances aer_hest_parse() so it
collects the union of the PCIe ACPI_HEST_FIRMWARE_FIRST flag settings when
no specific device is supplied.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Betty Dall <betty.dall@hp.com>
aer_set_firmware_first() searches the HEST for an error source descriptor
matching the specified PCI device. It uses the apei_hest_parse() iterator
to call aer_hest_parse() for every descriptor in the HEST.
Previously, aer_hest_parse() incorrectly assumed every descriptor was for a
PCIe error source. This patch adds a check to avoid that error.
[bhelgaas: factor check into helper, use in aer_hest_parse_aff(), changelog]
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save one indentation level in aer_print_error() for the generic case where
we have info->status of an error, disregard 80 cols rule a bit for the sake
of better readability, fix alignment.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and call it instead of duplicating the large printk format
statement.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.32+
This patch enhances the type safety for the kfifo API. It is now safe
to put const data into a non const FIFO and the API will now generate a
compiler warning when reading from the fifo where the destination
address is pointing to a const variable.
As a side effect the kfifo_put() does now expect the value of an element
instead a pointer to the element. This was suggested Russell King. It
make the handling of the kfifo_put easier since there is no need to
create a helper variable for getting the address of a pointer or to pass
integers of different sizes.
IMHO the API break is okay, since there are currently only six users of
kfifo_put().
The code is also cleaner by kicking out the "if (0)" expressions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pcie_ports parameter, which defaults to 'auto', allows a user
to specify if PCIe port services are disabled ('compat'), always
enabled ('native'), or only used when allowed by the BIOS
('auto').
Where CONFIG_ACPI isn't enabled, as is often the case for non
x86/ia64 platforms, the 'auto' behavior results in that of
'compat'. Thus in order to use port services on these platforms
'pcie_ports=native' must be added to the kernel command line.
This patch results in the 'native' behavior being followed where
'auto' is selected and ACPI is not enabled.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
One PCI bus reset function to rule them all.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert pciehp to be builtin only, with no module option.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The previous option title "PCI Express support" is confusing. The name
seems to imply this option is required to get PCIe support, which is not
true.
Fix it to "PCI Express Port Bus support" which is more accurate.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=X3Lo
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
* pci/betty-aer-v3:
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
When a PCIe device reports a fatal error, we reset the link leading
to it. Previously we only did this for devices below Downstream Ports,
not for devices directly below Root Ports.
This patch changes that so we reset the link leading to devices below
Root Ports just like we do for those below Downstream Ports.
[bhelgaas: changelog, keep dev_printk(KERN_DEBUG)]
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function aer_recover_queue() is a public interface and the
severity argument uses #defines that are in the private header
pci/pcie/aer/aerdrv.h.
This patch moves the #defines from pci/pcie/aer/aerdrv.h to
include/linux/aer.h.
[bhelgaas: split "remove 'extern' from declarations" to another patch]
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, we always updated info->firmware_first, even for HEST entries
that didn't match the device. Therefore, if the last HEST descriptor was
a PCIe structure that didn't match the device, we always cleared
dev->__aer_firmware_first.
Tested-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This factors out the matching of HEST structure type and PCIe device type
to improve readability. No functional change.
Tested-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AER is a PCIe-only capability, so there's no point in trying to match
a HEST PCIe structure with a non-PCIe device.
Previously, a HEST global AER bridge entry (type 8) could incorrectly
match *any* bridge, even a legacy PCI-PCI bridge, and a non-global
HEST entry could match a legacy PCI device.
Tested-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following warning was seen on 3.9 when a corrected PCIe error was being
handled by the AER subsystem.
WARNING: at .../drivers/pci/search.c:214 pci_get_dev_by_id+0x8a/0x90()
This occurred because a call to pci_get_domain_bus_and_slot() was added to
cper_print_pcie() to setup for the call to cper_print_aer(). The warning
showed up because cper_print_pcie() is called in an interrupt context and
pci_get* functions are not supposed to be called in that context.
The solution is to move the cper_print_aer() call out of the interrupt
context and into aer_recover_work_func() to avoid any warnings when calling
pci_get* functions.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some devices have hardware problems related to using ASPM. Drivers for
these devices use pci_disable_link_state() to prevent their device from
entering L0s or L1. But on platforms where the OS doesn't have permission
to manage ASPM, pci_disable_link_state() doesn't actually disable ASPM.
Windows has a similar mechanism ("PciASPMOptOut"), and when the OS doesn't
have control of ASPM, it doesn't actually disable ASPM either.
This patch just adds a warning in dmesg about the fact that
pci_disable_link_state() is doing nothing.
Reported-by: Emmanuel Grumbach <egrumbach@gmail.com>
Reference: https://lkml.kernel.org/r/CANUX_P3F5YhbZX3WGU-j1AGpbXb_T9Bis2ErhvKkFMtDvzatVQ@mail.gmail.com
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=57331
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/cleanup:
PCI: Remove "extern" from function declarations
PCI: Warn about failures instead of "must_check" functions
PCI: Remove __must_check from definitions
PCI: Remove unused variables
PCI: Move cpci_hotplug_init() proto to header file
PCI: Make local functions/structs static
PCI: Fix missing prototype for pcie_port_acpi_setup()
Conflicts:
drivers/pci/hotplug/acpiphp.h
include/linux/pci.h
We had an inconsistent mix of using and omitting the "extern" keyword
on function declarations in header files. This removes them all.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/misc:
PCI: Clean up quirk_io_region
PCI: Use vma_pages() to replace (vm_end - vm_start) >> PAGE_SHIFT
PCI: Use PCI_EXP_SLTCAP_PSN mask when extracting slot number
PCI: Remove unnecessary dependencies between PME and ACPI
[SCSI] mvumi: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
[SCSI] mvsas: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
ahci: Use PCI_VENDOR_ID_MARVELL_EXT for 0x1b4b
PCI: Define macro for Marvell vendor ID
PCI: Add MSI INTX_DISABLE quirks for AR8161/AR8162/AR8171/AR8172/E210X
PCI: aer_inject: Fix return values when device not found
PCIe PME doesn't depend on ACPI, so remove the #includes and
Kconfig dependency.
Based-on-patch-by: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This fixes a "no previous prototype" warning for pcie_port_acpi_setup()
found via "make W=1".
[bhelgaas: changelog]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the aer_inject driver returns -ENOTTY when the target PCIe
device root port is not found or if the device or root port doesn't
support AER.
In the case where the root port isn't found, the driver should return
-ENODEV, and in the other cases it should return -EPERM.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The runtime PM of PCIe ports turns out to be quite fragile, as in
some cases things work while in some other cases they don't and we
don't seem to have a good way to determine whether or not they are
going to work in advance.
For this reason, avoid enabling runtime PM for PCIe ports by
keeping their runtime PM reference counters always above 0 for the
time being.
When a PCIe port is suspended, it can no longer report events like
hotplug, so hotplug below the port may not work, as in the bug
report below.
[bhelgaas: changelog, stable]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.6+
Change to remove local PCI_BUS() define and use the new PCI_BUS_NUM()
interface from PCI.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
Don't allocate and track PCIe ASPM state when "pcie_aspm=off" is specified
on the kernel command line.
Based-on-patch-from: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Bulkow <david.bulkow@stratus.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
On PCI bus hotplug removal, pcie_aspm_exit_link_state() can potentially
skip parent devices that have link_state allocated. Instead of exiting
early if a given device is not PCIe, check whether or not the device's
parent has link_state allocated. This enables pcie_aspm_exit_link_state()
to properly clean up parent link_state when the last function in a slot
might not be PCIe.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Right now using pcie_aspm=force will not enable ASPM if the FADT indicates
ASPM is unsupported. However, the semantics of force should probably allow
for this, especially as they did before 3c076351c4 ("PCI: Rework ASPM
disable code")
This patch just skips the clearing of any ASPM setup that the firmware has
carried out on this bus if pcie_aspm=force is being used.
Reference: http://bugs.launchpad.net/bugs/962038
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
The function aer_recover_queue() calls pci_get_domain_bus_and_slot(), which
requires that the caller decrement the reference count with pci_dev_put().
This patch adds the missing call to pci_dev_put().
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
CC: stable@vger.kernel.org
These changes make cper_print_aer more consistent with aer_print_error
and clean things up by elimiating the use of the prefix variable and
replacing it with dev_printk.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Boris Petkov <bp@alien8.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch will provide a more reliable and easy way for user-space
applications to have access to AER logs rather than reading them from the
message buffer. It also provides a way to notify user-space when an AER
event occurs.
The aer driver is updated to generate a trace event of function 'aer_event'
when a PCIe error is reported over the AER interface. The trace event was
added to both the interrupt based aer path and the firmware first path.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Boris Petkov <bp@alien8.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Ulrich reported that his USB3 cardreader does not work reliably when
connected to the USB3 port. It turns out that USB3 controller failed to
awaken when plugging in the USB3 cardreader. Further experiments found
that the USB3 host controller can only be awakened via polling, not via PME
interrupt. But if the PCIe port to which the USB3 host controller is
connected is suspended, we cannot poll the controller because its config
space is not accessible when the PCIe port is in a low power state.
To solve the issue, the PCIe port will not be suspended if any subordinate
device needs PME polling.
[bhelgaas: use bool consistently rather than mixing int/bool]
Reference: http://lkml.kernel.org/r/50841CCC.9030809@uli-eckhardt.de
Reported-by: Ulrich Eckhardt <usb@uli-eckhardt.de>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
* pci/bjorn-pcie-cap:
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
PCI: Add and use standard PCI-X Capability register names
Add standard #defines for ASPM fields in PCI Express Link Capability and
Link Control registers.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an error is detected on a PCIe device which does not have an
AER-aware driver, prevent AER infrastructure from reporting
successful error recovery.
This is because the report_error_detected() function that gets
called in the first phase of recovery process allows forward
progress even when the driver for the device does not have AER
capabilities. It seems that all callbacks (in pci_error_handlers
structure) registered by drivers that gets called during error
recovery are not mandatory. So the intention of the infrastructure
design seems to be to allow forward progress even when a specific
callback has not been registered by a driver. However, if error
handler structure itself has not been registered, it doesn't make
sense to allow forward progress.
As a result of the current design, in the case of a single device
having an AER-unaware driver or in the case of any function in a
multi-function card having an AER-unaware driver, a successful
recovery is reported.
Typical scenario this happens is when a PCI device is detached
from a KVM host and the pci-stub driver on the host claims the
device. The pci-stub driver does not have error handling capabilities
but the AER infrastructure still reports that the device recovered
successfully.
The changes proposed here leaves the device(s)in an unrecovered state
if the driver for the device or for any device in the subtree
does not have error handler structure registered. This reflects
the true state of the device and prevents any partial recovery (or no
recovery at all) reported as successful.
[bhelgaas: changelog]
Signed-off-by: Vijay Mohan Pandarathil <vijaymohan.pandarathil@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linas Vepstas <linasvepstas@gmail.com>
Reviewed-by: Myron Stowe <myron.stowe@redhat.com>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 2dcfaf85 mistakenly dropped the "flags & PCI_EXP_FLAGS_SLOT" test,
so now we create hotplug slots even for PCIe port devices that don't
support hotplug. This patch fixes this problem.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
If a PCI device and its parents are put into D3cold, unbinding the
device will trigger deadlock as follow:
- driver_unbind
- device_release_driver
- device_lock(dev) <--- previous lock here
- __device_release_driver
- pm_runtime_get_sync
...
- rpm_resume(dev)
- rpm_resume(dev->parent)
...
- pci_pm_runtime_resume
...
- pci_set_power_state
- __pci_start_power_transition
- pci_wakeup_bus(dev->parent->subordinate)
- pci_walk_bus
- device_lock(dev) <--- deadlock here
If we do not do device_lock in pci_walk_bus, we can avoid deadlock.
Device_lock in pci_walk_bus is introduced in commit:
d71374dafb, corresponding email thread
is: https://lkml.org/lkml/2006/5/26/38. The patch author Zhang Yanmin
said device_lock is added to pci_walk_bus because:
Some error handling functions call pci_walk_bus. For example, PCIe
aer. Here we lock the device, so the driver wouldn't detach from the
device, as the cb might call driver's callback function.
So I fixed the deadlock as follows:
- remove device_lock from pci_walk_bus
- add device_lock into callback if callback will call driver's callback
I checked pci_walk_bus users one by one, and found only PCIe aer needs
device lock.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
CC: Zhang Yanmin <yanmin.zhang@intel.com>
* pci/trivial:
PCI: Drop duplicate const in DECLARE_PCI_FIXUP_SECTION
PCI: Drop bogus default from ARCH_SUPPORTS_MSI
PCI: cpqphp: Remove unreachable path
PCI: Remove bus number resource debug messages
PCI/AER: Print completion message at KERN_INFO to match starting message
PCI: Fix drivers/pci/pci.c kernel-doc warnings
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
Since pci_error_handlers is just a function table make it const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
On some platforms, root port has neither MSI/MSI-X nor INTx interrupt
generated in RC mode. In this case, we have to use other interrupt, e.g.,
system shared interrupt, for port service IRQ to have AER, Hot-plug, etc.,
services work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The completion message in do_recovery() is currently KERN_DEBUG,
while the starting message in aer_print_port_info() is KERN_INFO.
This changes the completion message to KERN_INFO to match the
starting message.
[bhelgaas: changelog, use dev_info() instead of dev_printk(KERN_INFO)]
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following bug:
http://marc.info/?l=linux-pci&m=134338059022620&w=2
Where lspci does not work properly if a device and the corresponding
parent bridge (such as PCIe port) is suspended. This is because the
device configuration space registers will be not accessible if the
corresponding parent bridge is suspended or the device is put into
D3cold state.
To solve the issue, the bridge/PCIe port connected to the device is
put into active state before read/write configuration space registers.
If the device is in D3cold state, it will be put into active state
too.
To avoid resume/suspend PCIe port for each configuration register
read/write, a small delay is added before the PCIe port to go
suspended.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the following bug:
http://marc.info/?l=linux-usb&m=134318961120825&w=2
Originally, device lower power states include D1, D2, D3. After that,
D3 is further divided into D3hot and D3cold. To support both scenario
safely, original D3 is mapped to D3cold.
When adding D3cold support, because worry about some device may have
broken D3cold support, D3cold is disabled by default. This disable D3
on original platform too. But some original platform may only have
working D3, but no working D1, D2. The root cause of the above bug is
it too.
To deal with this, this patch enables D3/D3cold by default for most
devices. This restores the original behavior. For some devices that
suspected to have broken D3cold support, such as PCIe port, D3cold is
disabled by default.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
This patch adds runtime D3cold support and corresponding ACPI platform
support. This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.
D3cold is the deepest power saving state for a PCIe device, where its main
power is removed. While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.
To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal. WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.
Some devices, such as those in plug-in slots, have no direct platform
logic. For example, there is usually no ACPI _PR3 for them. D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device. When the PCIe port is powered on/off, the device is powered
on/off too. Wakeup events from the device will be notified to the
corresponding PCIe port.
For more information about PCIe D3cold and corresponding ACPI support,
please refer to:
- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0
[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch adds runtime PM support to PCIe port. This is needed by
PCIe D3cold support, where PCIe device without ACPI node may be
powered on/off by PCIe port.
Because runtime suspend is broken for some chipsets, a black list is
used to disable runtime PM support for these chipsets.
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
CC: Huang Ying <ying.huang@intel.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Get rid of these:
drivers/pci/pcie/portdrv_core.c: In function 'pcie_port_device_register':
drivers/pci/pcie/portdrv_core.c:275:16: warning: 'cap_mask' may be used
uninitialized in this function [-Wuninitialized]
drivers/pci/pcie/portdrv_core.c:240:6: note: 'cap_mask' was declared here
In some cases, 'cap_mask' may be not set in pcie_port_platform_notify,
holding a garbage value.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected. Passing pcie_aspm=force on the kernel command line
works around it.
The cause: commit 4949be1682 ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.
This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on. Move the aspm_disabled check so we continue to honour
that scenario.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
http://bugs.debian.org/665420
Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Right now we won't touch ASPM state if ASPM is disabled, except in the case
where we find a device that appears to be too old to reliably support ASPM.
Right now we'll clear it in that case, which is almost certainly the wrong
thing to do. The easiest way around this is just to disable the blacklisting
when ASPM is disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a parameter to avoid using MSI/MSI-X for PCIe native hotplug; it's
known to be buggy on some platforms.
In my environment, while shutting down, following stack trace is shown
sometimes.
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 1081, comm: reboot Not tainted 3.2.0 #1
Call Trace:
<IRQ> [<ffffffff810cec1d>] __report_bad_irq+0x3d/0xe0
[<ffffffff810cee1c>] note_interrupt+0x15c/0x210
[<ffffffff810cc485>] handle_irq_event_percpu+0xb5/0x210
[<ffffffff810cc621>] handle_irq_event+0x41/0x70
[<ffffffff810cf675>] handle_fasteoi_irq+0x55/0xc0
[<ffffffff81015356>] handle_irq+0x46/0xb0
[<ffffffff814fbe9d>] do_IRQ+0x5d/0xe0
[<ffffffff814f146e>] common_interrupt+0x6e/0x6e
[<ffffffff8106b040>] ? __do_softirq+0x60/0x210
[<ffffffff8108aeb1>] ? hrtimer_interrupt+0x151/0x240
[<ffffffff814fb5ec>] call_softirq+0x1c/0x30
[<ffffffff810152d5>] do_softirq+0x65/0xa0
[<ffffffff8106ae9d>] irq_exit+0xbd/0xe0
[<ffffffff814fbf8e>] smp_apic_timer_interrupt+0x6e/0x99
[<ffffffff814f9e5e>] apic_timer_interrupt+0x6e/0x80
<EOI> [<ffffffff814f0fb1>] ? _raw_spin_unlock_irqrestore+0x11/0x20
[<ffffffff812629fc>] pci_bus_write_config_word+0x6c/0x80
[<ffffffff81266fc2>] pci_intx+0x52/0xa0
[<ffffffff8127de3d>] pci_intx_for_msi+0x1d/0x30
[<ffffffff8127e4fb>] pci_msi_shutdown+0x7b/0x110
[<ffffffff81269d34>] pci_device_shutdown+0x34/0x50
[<ffffffff81326c4f>] device_shutdown+0x2f/0x140
[<ffffffff8107b981>] kernel_restart_prepare+0x31/0x40
[<ffffffff8107b9e6>] kernel_restart+0x16/0x60
[<ffffffff8107bbfd>] sys_reboot+0x1ad/0x220
[<ffffffff814f4b90>] ? do_page_fault+0x1e0/0x460
[<ffffffff811942d0>] ? __sync_filesystem+0x90/0x90
[<ffffffff8105c9aa>] ? __cond_resched+0x2a/0x40
[<ffffffff814ef090>] ? _cond_resched+0x30/0x40
[<ffffffff81169e17>] ? iterate_supers+0xb7/0xd0
[<ffffffff814f9382>] system_call_fastpath+0x16/0x1b
handlers:
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
[<ffffffff8138a0f0>] usb_hcd_irq
Disabling IRQ #16
An un-wanted interrupt is generated when PCI driver switches from
MSI/MSI-X to INTx while shutting down the device. The interrupt does
not happen if MSI/MSI-X is not used on the device.
I confirmed that this problem does not happen if pcie_hp=nomsi was
specified and hotplug operation worked fine as usual.
v2: Automatically disable MSI/MSI-X against following device:
PCI bridge: Integrated Device Technology, Inc. Device 807f (rev 02)
v3: Based on the review comment, combile the if statements.
v4: Removed module parameter.
Move some code to build pciehp as a module.
Move device specific code to driver/pci/quirks.c.
v5: Drop a device specific code until getting a vendor statement.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Distributions may wish to provide different defaults for PCIE ASPM
depending on their target audience. Provide a configuration option for
choosing the default policy.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Right now we forcibly clear ASPM state on all devices if the BIOS indicates
that the feature isn't supported. Based on the Microsoft presentation
"PCI Express In Depth for Windows Vista and Beyond", I'm starting to think
that this may be an error. The implication is that unless the platform
grants full control via _OSC, Windows will not touch any PCIe features -
including ASPM. In that case clearing ASPM state would be an error unless
the platform has granted us that control.
This patch reworks the ASPM disabling code such that the actual clearing
of state is triggered by a successful handoff of PCIe control to the OS.
The general ASPM code undergoes some changes in order to ensure that the
ability to clear the bits isn't overridden by ASPM having already been
disabled. Further, this theoretically now allows for situations where
only a subset of PCIe roots hand over control, leaving the others in the
BIOS state.
It's difficult to know for sure that this is the right thing to do -
there's zero public documentation on the interaction between all of these
components. But enough vendors enable ASPM on platforms and then set this
bit that it seems likely that they're expecting the OS to leave them alone.
Measured to save around 5W on an idle Thinkpad X220.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
In addition to native PCIe AER, now APEI (ACPI Platform Error
Interface) GHES (Generic Hardware Error Source) can be used to report
PCIe AER errors too. To add support to APEI GHES PCIe AER recovery,
aer_recover_queue is added to export the recovery function in native
PCIe AER driver.
Recoverable PCIe AER errors are reported via NMI in APEI GHES. Then
APEI GHES uses irq_work to delay the error processing into an IRQ
handler. But PCIe AER recovery can be very time-consuming, so
aer_recover_queue, which can be used in IRQ handler, delays the real
recovery action into the process context, that is, work queue.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Merriam-Webster tells us that the word exists. However ...
* Google suggests `forcibly' because it doesn't recognize `forcedly'.
* Google lists 494 thousand results for `forcedly'.
* Google lists 13.7 million results for `forcibly'.
* Linus's repo contains 1 occurrence of `forcedly' ( 0 after my change).
* Linus's repo contains 60 occurrences of `forcibly' (61 after my change).
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the commit 28eb5f2, aer_osc_setup is removed but corresponding
definiton information in the aerdrv.h is missed.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If it was preempted, and the variable aer_mask_override is changed
after the spin_unlock_irqrestore it will write an uninitialized
variable by the pci_write_config_dword() function.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 2f671e2d allowed us to clear ASPM state when the FADT
tells us it isn't supported, but we don't put this into effect
if the aspm_policy is set to POLICY_POWERSAVE. Enable the
state to be cleared regardless of policy.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Disable ASPM when _OSC control is not granted for PCIe services
PCI: Changing ASPM policy, via /sys, to POWERSAVE could cause NMIs
PCI: PCIe links may not get configured for ASPM under POWERSAVE mode
PCI/ACPI: Report ASPM support to BIOS if not disabled from command line
The AER error information printing support is implemented in
drivers/pci/pcie/aer/aer_print.c. So some string constants, functions
and macros definitions can be re-used without being exported.
The original PCIe AER error information printing function is not
re-used directly because the overall format is quite different. And
changing the original printing format may make some original users'
scripts broken.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When printing PCIe AER error information, each line is prefixed with
PCIe device and driver information. In original implementation, the
prefix is generated when each line is printed. In fact, all lines
share the same prefix. So this patch pre-generated the prefix, and
use that one when each line is printed.
In addition to common prefix can be pre-generated, the trailing white
spaces in string constants and NULLs in char * array constants can be
removed too. These can reduce the object file size further.
The size of object file before and after changing is as follow:
text data bss dec
before: 3038 0 0 3038
after: 2118 0 0 2118
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
v3 -> v2: Added text to describe the problem
v2 -> v1: Split this patch from v1
v1 : Part of: http://marc.info/?l=linux-pci&m=130042212003242&w=2
Disable ASPM when no _OSC control for PCIe services is granted
by the BIOS. This is to protect systems with a buggy BIOS that
did not set the ACPI FADT "ASPM Controls" bit even though the
underlying HW can't do ASPM.
To turn "on" ASPM the minimum the BIOS needs to do:
1. Clear the ACPI FADT "ASPM Controls" bit.
2. Support _OSC appropriately
There is no _OSC Control bit for ASPM. However, we expect the BIOS to
support _OSC for a Root Bridge that originates a PCIe hierarchy. If this
is not the case - we are better off not enabling ASPM on that server.
Commit 852972acff (ACPI: Disable ASPM if the
Platform won't provide _OSC control for PCIe) describes the above scenario.
To quote verbatim from there:
[The PCI SIG documentation for the _OSC OS/firmware handshaking interface
states:
"If the _OSC control method is absent from the scope of a host bridge
device, then the operating system must not enable or attempt to use any
features defined in this section for the hierarchy originated by the host
bridge."
The obvious interpretation of this is that the OS should not attempt to use
PCIe hotplug, PME or AER - however, the specification also notes that an
_OSC method is *required* for PCIe hierarchies, and experimental validation
with An Alternative OS indicates that it doesn't use any PCIe functionality
if the _OSC method is missing. That arguably means we shouldn't be using
MSI or extended config space, but right now our problems seem to be limited
to vendors being surprised when ASPM gets enabled on machines when other
OSs refuse to do so. So, for now, let's just disable ASPM if the _OSC
method doesn't exist or refuses to hand over PCIe capability control.]
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3 -> v2: Modified the text that describes the problem
v2 -> v1: Returned -EPERM
v1 : http://marc.info/?l=linux-pci&m=130013194803727&w=2
For servers whose hardware cannot handle ASPM the BIOS ought to set the
FADT bit shown below:
In Sec 5.2.9.3 (IA-PC Boot Arch. Flags) of ACPI4.0a Specification, please
see Table 5-11:
PCIe ASPM Controls: If set, indicates to OSPM that it must not enable
OPSM ASPM control on this platform.
However there are shipping servers whose BIOS did not set this bit. (An
example is the HP ProLiant DL385 G6. A Maintenance BIOS will fix that).
For such servers even if a call is made via pci_no_aspm(), based on _OSC
support in the BIOS, it may be too late because the ASPM code may have
already allocated and filled its "link_list".
So if a user sets the ASPM "policy" to "powersave" via /sys then
pcie_aspm_set_policy() will run through the "link_list" and re-configure
ASPM policy on devices that advertise ASPM L0s/L1 capability:
# echo powersave > /sys/module/pcie_aspm/parameters/policy
# cat /sys/module/pcie_aspm/parameters/policy
default performance [powersave]
That can cause NMIs since the hardware doesn't play well with ASPM:
[ 1651.906015] NMI: PCI system error (SERR) for reason b1 on CPU 0.
[ 1651.906015] Dazed and confused, but trying to continue
Ideally, the BIOS should have set that FADT bit in the first place but we
could be more robust - especially given the fact that Windows doesn't
cause NMIs in the above scenario.
There should be a sanity check to not allow a user to modify ASPM policy
when aspm_disabled is set.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
v3 -> v2: Moved ASPM enabling logic to pci_set_power_state()
v2 -> v1: Preserved the logic in pci_raw_set_power_state()
: Added ASPM enabling logic after scanning Root Bridge
: http://marc.info/?l=linux-pci&m=130046996216391&w=2
v1 : http://marc.info/?l=linux-pci&m=130013164703283&w=2
The assumption made in commit 41cd766b06
(PCI: Don't enable aspm before drivers have had a chance to veto it) that
pci_enable_device() will result in re-configuring ASPM when aspm_policy is
POWERSAVE is no longer valid. This is due to commit
97c145f7c8 (PCI: read current power state
at enable time) which resets dev->current_state to D0. Due to this the
call to pcie_aspm_pm_state_change() is never made. Note the equality check
(below) that returns early:
./drivers/pci/pci.c: pci_raw_set_pci_power_state()
546 /* Check if we're already there */
547 if (dev->current_state == state)
548 return 0;
Therefore OSPM never configures the PCIe links for ASPM to turn them "on".
Fix it by configuring ASPM from the pci_enable_device() code path. This
also allows a driver such as the e1000e networking driver a chance to
disable ASPM (L0s, L1), if need be, prior to enabling the device. A
driver may perform this action if the device is known to mis-behave
wrt ASPM.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to distinguish the situation in which ASPM support is
disabled from the command line or through .config from the situation
in which it is disabled, because the hardware or BIOS can't handle
it. In the former case we should not report ASPM support to the BIOS
through ACPI _OSC, but in the latter case we should do that.
Introduce pcie_aspm_support_enabled() that can be used by
acpi_pci_root_add() to determine whether or not it should report ASPM
support to the BIOS through _OSC.
Cc: stable@kernel.org
References: https://bugzilla.kernel.org/show_bug.cgi?id=29722
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I have several systems which have the same problem: The PCIe AER
corrected and uncorrected masks have all the error bits set. This
results in the inablility to test with the aer_inject module & utility
on those systems.
Add the 'aer_mask_override' module parameter which will override the
corrected or uncorrected masks for a PCI device. The mask will have the
bit corresponding to the status passed into the aer_inject() function.
After this patch it is possible to successfully use the aer_inject
utility on those PCI slots.
Successfully tested by me on a Dell and Intel whitebox which exhibited
the mask problem.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that PCI Express PMEs don't work on my Toshiba Portege R500
after the system has been woken up from a sleep state by a PME
(through Wake-on-LAN). After some investigation it turned out that
the BIOS didn't clear the Root PME Status bit in the root port that
received the wakeup PME and since the Requester ID was also set in
the port's Root Status register, any subsequent PMEs didn't trigger
interrupts.
This problem can be avoided by clearing the Root PME Status bits in
all PCI Express root ports during early resume. For this purpose,
add an early resume routine to the PCIe port driver and make this
driver be always registered, even if pci_ports_disable is set (in
which case the driver's only function is to provide the early
resume callback).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We currently refuse to touch the ASPM registers if the BIOS tells us that
ASPM isn't supported. This can cause problems if the BIOS has (for any
reason) enabled ASPM on some devices anyway. Change the code such that we
explicitly clear ASPM if the FADT indicates that ASPM isn't supported,
and make sure we tidy up appropriately on device removal in order to deal
with the hotplug case. If ASPM is disabled because the BIOS doesn't hand
over control then we won't touch the registers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
There is a design issue related to PCIe AER and _OSC that the BIOS
may be asked to grant control of the AER service even if some
Hardware Error Source Table (HEST) entries contain information
meaning that the BIOS really should control it. Namely,
pcie_port_acpi_setup() calls pcie_aer_get_firmware_first() that
determines whether or not the AER service should be controlled by
the BIOS on the basis of the HEST information for the given PCIe
port. The BIOS is asked to grant control of the AER service for
a PCIe Root Complex if pcie_aer_get_firmware_first() returns 'false'
for at least one root port in that complex, even if all of the other
root ports' HEST entries have the FIRMWARE_FIRST flag set (and none
of them has the GLOBAL flag set). However, if the AER service is
controlled by the kernel, that may interfere with the BIOS' handling
of the error sources having the FIRMWARE_FIRST flag. Moreover,
there may be PCIe endpoints that have the FIRMWARE_FIRST flag set in
HEST and are attached to the root ports in question, in which case it
also may be unsafe to ask the BIOS for control of the AER service.
For this reason, introduce a function checking if there's at least
one PCIe-related HEST entry with the FIRMWARE_FIRST flag set and
disable the native AER service altogether if this function returns
'true'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
quiet the warning about use of uninitialized e_src in
aer_isr() e_src is initialized by get_e_source()
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The PCIe port driver's module exit routine is never used, so drop it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe PME code only consists of one file, so it doesn't need to
occupy its own directory. Move it to drivers/pci/pcie/pme.c and
remove the contents of drivers/pci/pcie/pme .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In principle PCIe port services may be enabled by the BIOS, so it's
better to disable them during port initialization to avoid spurious
events from being generated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is possible that the BIOS will not grant control of all _OSC
features requested via acpi_pci_osc_control_set(), so it is
recommended to negotiate the final set of _OSC features with the
query flag set before calling _OSC to request control of these
features.
To implement it, rework acpi_pci_osc_control_set() so that the caller
can specify the mask of _OSC control bits to negotiate and the mask
of _OSC control bits that are absolutely necessary to it. Then,
acpi_pci_osc_control_set() will run _OSC queries in a loop until
the mask of _OSC control bits returned by the BIOS is equal to the
mask passed to it. Also, before running the _OSC request
acpi_pci_osc_control_set() will check if the caller's required
control bits are present in the final mask.
Using this mechanism we will be able to avoid situations in which the
BIOS doesn't grant control of certain _OSC features, because they
depend on some other _OSC features that have not been requested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce kernel command line switch pcie_ports= allowing one to
disable all of the native PCIe port services, so that PCIe ports
are treated like PCI-to-PCI bridges.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a function allowing the caller to check whether to try to
enable PCIe AER.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
The CONFIG_PCIEASPM option is confusing and potentially dangerous. ASPM is
a hardware mediated feature rather than one under direct OS control, and
even if the config option is disabled the system firmware may have turned
on ASPM on various bits of hardware. This can cause problems later -
various hardware that claims to support ASPM does a poor job of it and may
hang or cause other difficulties. The kernel is able to recognise this in
many cases and disable the ASPM functionality, but only if CONFIG_PCIEASPM
is enabled.
Given that in its default configuration this option will either leave the
hardware as it was originally or disable hardware functionality that may
cause problems, it should by default y. The only reason to disable it
ought to be to reduce code size, so make it dependent on CONFIG_EMBEDDED.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: lrodriguez@atheros.com
Cc: maximlevitsky@gmail.com
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The aspm code will currently set the configured aspm policy before drivers
have had an opportunity to indicate that their hardware doesn't support it.
Unfortunately, putting some hardware in L0 or L1 can result in the hardware
no longer responding to any requests, even after aspm is disabled. It makes
more sense to leave aspm policy at the BIOS defaults at initial setup time,
reconfiguring it after pci_enable_device() is called. This allows the
driver to blacklist individual devices beforehand.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some compiler generates following warnings:
In function 'aer_isr':
warning: 'e_src.id' may be used uninitialized in this function
warning: 'e_src.status' may be used uninitialized in this function
Avoid status flag "int ret" and return constants instead, so that
gcc sees the return value matching "it is initialized" better.
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One of the arguments during the suspend blockers discussion was that
the mainline kernel didn't contain any mechanisms making it possible
to avoid races between wakeup and system suspend.
Generally, there are two problems in that area. First, if a wakeup
event occurs exactly when /sys/power/state is being written to, it
may be delivered to user space right before the freezer kicks in, so
the user space consumer of the event may not be able to process it
before the system is suspended. Second, if a wakeup event occurs
after user space has been frozen, it is not generally guaranteed that
the ongoing transition of the system into a sleep state will be
aborted.
To address these issues introduce a new global sysfs attribute,
/sys/power/wakeup_count, associated with a running counter of wakeup
events and three helper functions, pm_stay_awake(), pm_relax(), and
pm_wakeup_event(), that may be used by kernel subsystems to control
the behavior of this attribute and to request the PM core to abort
system transitions into a sleep state already in progress.
The /sys/power/wakeup_count file may be read from or written to by
user space. Reads will always succeed (unless interrupted by a
signal) and return the current value of the wakeup events counter.
Writes, however, will only succeed if the written number is equal to
the current value of the wakeup events counter. If a write is
successful, it will cause the kernel to save the current value of the
wakeup events counter and to abort the subsequent system transition
into a sleep state if any wakeup events are reported after the write
has returned.
[The assumption is that before writing to /sys/power/state user space
will first read from /sys/power/wakeup_count. Next, user space
consumers of wakeup events will have a chance to acknowledge or
veto the upcoming system transition to a sleep state. Finally, if
the transition is allowed to proceed, /sys/power/wakeup_count will
be written to and if that succeeds, /sys/power/state will be written
to as well. Still, if any wakeup events are reported to the PM core
by kernel subsystems after that point, the transition will be
aborted.]
Additionally, put a wakeup events counter into struct dev_pm_info and
make these per-device wakeup event counters available via sysfs,
so that it's possible to check the activity of various wakeup event
sources within the kernel.
To illustrate how subsystems can use pm_wakeup_event(), make the
low-level PCI runtime PM wakeup-handling code use it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: markgross <markgross@thegnar.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Commit c7f486567c
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav KamenÃk and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Jaroslav KamenÃk <jaroslav@kamenik.cz>
Tested-by: Antoni Grzymala <antekgrzymala@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Skip zero-ing in aer_alloc_rpc() since it is allocated by kzalloc().
The closing comment marker "*/" is recommended for kernel-doc comments.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed that when I inject a fatal error to an endpoint via
aer-inject, aer_root_reset() is called as reset_link for a
downstream port at upstream of the endpoint:
pcieport 0000:00:06.0: AER: Uncorrected (Fatal) error received: id=5401
:
pcieport 0000:52:02.0: Root Port link has been reset
It externally appears to be working, but internally issues some
accesses to PCI_ERR_ROOT_COMMAND/STATUS registers that is for
root port so not available on downstream port.
This patch introduces default_downstream_reset_link that is
a version of aer_root_reset() with no accesses to root port's
register. It is used for downstream ports that has no reset_link
function its specific.
This patch also updates related description in pcieaer-howto.txt.
Some minor fixes are included.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie->port of port service device points the port associated
the service with. The find_aer_service iterates over children of
given port udev.
So it is clear that the pcie->port of port service of given port
udev must always point the udev.
Therefore we can know the type of udev without checking its children.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make it clear that we only interest in 2 *_RCV bits.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current get_e_source() returns pointer to an element of array.
However since it also progress consume counter, it is possible
that the element is overwritten by newly produced data before
the element is really consumed.
This patch changes get_e_source() to copy contents of the element
to address pointed by its caller. Once copied the element in
array can be consumed.
And relocate this function to more innocuous place.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Divide tricky for-loop into readable if-blocks.
The logic to set multi_error_valid (to force walking pci bus
hierarchy to find 2nd~ error devices) is changed too, to check
MULTI_{,_UN}COR_RCV bit individually and to force walk only when
it is required.
And rework setting e_info->severity for uncorrectable, not to use
magic numbers.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stop iteration if we cannot register any more.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Take core part of find_device_iter() to make a new function
is_error_source() that checks given device has report an error
or not.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Return bool to indicate that the source device is found or not.
This allows us to skip calling aer_process_err_devices() if we can.
And move dev_printk for debug into this function.
v2: return bool instead of int
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These functions are only called from init/remove path of aerdrv,
so move them from aerdrv_core.c to aerdrv.c, to make them static.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This cleanup solves some minor naming issues by removing unuseful
function aer_delete_rootport() and by renaming disable_root_aer()
to aer_disable_rootport().
- Inconsistent location of alloc & free:
The struct rpc is allocated in aer_alloc_rpc() at aerdrv.c
while it is implicitly freed in aer_delete_rootport() at
aerdrv_core.c.
- Inconsistent function name:
It makes a bit confusion that aer_delete_rootport() is seemed
to be paired with aer_enable_rootport(), i.e. there is neither
"add" against "delete" nor "disable" against "enable".
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While testing completion timeouts I found that hardware was not recovering.
It looks like the hot reset was never being propagated to the endpoint
devices on the bus due to the fact that we were clearing the bit too
quickly.
The documentation I have states that we should be transmitting hot reset
TS1s for 2ms. To achieve this I have added a 2ms delay from the time we
set the secondary bus reset bit to the time we clear it. In addition I
changed the define used for the secondary bus reset bit to match the
register define that was being used.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).
This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe
capability offset. This reduces redundant search in PCI configuration
space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.
Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register. At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle. If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set. After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]
Implement a driver for the PCIe PME root port service working in
accordance with the above description.
Based on a patch from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.
If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Youquan, Song <youquan.song@intel.com>
Acked-by: Ying, Huang <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf
Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25. Time to remove the dead code.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes. The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error. One of the errors will not be
cleared.
This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:
- Remove struct pcie_port_data because it no longer has any field.
- Remove portdrv private definitions about port type (PCIE_RC_PORT,
PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
definitions instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing service irqs cleanup in the error code path of
pcie_port_device_register().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Call pci_enable_device() before initializing service irqs, because
legacy interrupt is initialized in pci_enable_device() on some
architectures.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch cleans up the service irqs initialization as follows:
- Remove 'irq_mode' field in pcie_port_data and related definitions,
which is not needed because we can get the same information from
'is_msix', 'is_msi' and 'pin' fields in struct pci_dev.
- Change the name of 'vectors' argument of assign_interrupt_mode() to
'irqs' because it holds irq numbers actually. People might confuse
it with CPU vector or MSI/MSI-X vector.
- Change function name assign_interrupt_mode() to init_service_irqs()
becasuse we no longer have 'irq_mode' data structure, and new name
is more straightforward (IMO).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No reason to check PME capability outside get_port_device_capability().
Do it in get_port_device_capability().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe port type is already stored in 'pcie_type' field of struct
pci_dev. So we don't need to get it from pci configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current port bus driver implementation, pcie_device allocation,
initialization and registration are done in separated functions. Doing
those in one function make the code simple and easier to read.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need pcie_port_device_probe() because we can get pci
device/port type using pci_is_pcie() and 'pcie_type' fields in struct
pci_dev. Remove pcie_port_device_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changes for PCIe AER driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCIe ASPM driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe ASPM driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI Express Port Bus driver. This avoids unnecessary serarch
in PCI configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe AER driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Replaced some error return values in aer_inject. Use -ENODEV when we
can't find a device and -ENOTTY when the device does not support PCIe AER.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI domains (segments) to aer_inject.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated. This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST. PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.
Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.
However, _OSC alone is insufficient for newer BIOSes. Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle. One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.
Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions. The aer driver should honor this, and
not attach itself to devices noted as such.
Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode. Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.
The HEST parsing code may be replaced in the future by a more
feature-rich implementation. This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to include "-driver" in the driver name.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When booting with pci=nomsi aer causes lost interrupts and
lockdep inversions.
So check if MSIs are not disabled before initializing the aer
driver.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The definition of the ASPM support field in the Link Capabilities
Register had been changed by the "ASPM optionality ECN" as follows:
<Before>
00b Reserved
01b L0s Supported
10b Reserved
11b L0s and L1 Supported
<After>
00b No ASPM Support
01b L0s Supported
10b L1 Supported
11b L0s and L1 Supported
Current linux ASPM driver doesn't enable ASPM if the support field is
00b or 10b. So there is no impact about 00b. But current linux ASPM
driver doesn't enable L1 if the support field is 10b. With this patch,
10b (L1 support) is handled properly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit c82f63e411
(PCI: check saved state before restore) pcie_portdrv_slot_reset()
may not work correctly if dev->error_state is equal to
pci_channel_io_frozen, because dev->state_saved need not be set at
that time. Fix this issue by setting dev->state_saved before
pci_restore_state() is called in pcie_portdrv_slot_reset().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By having a pointer to the root port link, we can remove loops in
get_root_port_link() to search the root port link.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need the 'has_switch' field in the struct pcie_link_state.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for calc_L0S_latency() and calc_L1_latency().
- Separate exit latency and acceptable latency calculation.
- Some minor cleanups.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, callers of pcie_set_clock_pm() check
Clock PM capability of the link or current Clock PM state of the link.
This check should be done in pcie_set_clock_pm() itself.
This patch moves those checks into pcie_set_clock_pm(). It also
introduces pcie_set_clkpm_nocheck() that is equivalent to old
pcie_set_clock_pm(), for the caller who wants to change Clocl PM state
regardless of the Clock PM capability or current Clock PM state. In
addition, this patch changes the function name from
pcie_set_clock_pm() to pcie_set_clkpm() for consistency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up ASPM initialization by refactoring some functionality, renaming
functions, and moving things around.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, there are many functions that
take a pointer to struct pci_dev corresponding to the upstream component
of the link as a parameter. But, since those functions handle PCI
express link state, a pointer to struct pcie_link_state is more
suitable than a pointer to struct pci_dev. Changing a parameter to a
pointer to struct pcie_link_state makes ASPM code much simpler and
easier to read. This patch also contains some minor cleanups. This patch
doesn't have any functional change.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for some fields in pcie_link_state.
- Add comments.
- make "downstream_has_switch" field 1-bit.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "clk_pm_capable", "clk_pm_enable" and "bios_clk_state" fields in
the struct pcie_link_state only take 1-bit value. So those fields
don't need to be defined as unsigned int. This patch makes those
fields 1-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up latency related data structures for ASPM.
- Introduce struct acpi_latency for exit latency and acceptable
latency management. With this change, struct endpoint_state is no
longer needed.
- We don't need to hold both upstream latency and downstream latency
in the current implementation.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "support_state", "enabled_state" and "bios_aspm_state" fields in
the struct pcie_link_state take 2-bit value. So those fields don't
need to be defined as unsigned int. This patch makes those fields
2-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix a typo in struct pcie_link_state.
The "sibiling" field in the struct pcie_link_state should be
"sibling".
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Debugging PCIE AER code can be very difficult because it is hard
to trigger various real hardware errors. This patch provide a
software based error injection tool, which can fake various PCIE
errors with a user space helper tool named "aer-inject". Which
can be gotten from:
http://www.kernel.org/pub/linux/kernel/people/yhuang/
The patch fakes AER error by faking some PCIE AER related
registers and an AER interrupt for specified the PCIE device.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When a root port receives the same errors more than once before the
kernel process them, the Multiple Error Messages Received flags are set
by hardware. Because the root port could only save one kind of
correctable error source id and another uncorrectable error source id at
the same time, the second message sender id is lost if the 2 messages
are sent from 2 different devices. This patch makes the kernel search
all devices under the root port when multiple messages are received.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When the bus id part of error source id is equal to 0 or nosourceid=1,
make the kernel probe the AER status registers of all devices under the
root port to find the initial error reporter.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is used by PCIE AER error injection to fake an PCI AER interrupt.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
VIA has a strange chipset, it has root port under a bridge. Disable ASPM
for such strange chipset.
Cc: stable@kernel.org
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe port driver calls pci_enable_device when registering
ports, but never calls pci_disable_device during removal.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 55633af3 (PCIe portdrv: Use driver data to simplify code)
added a kfree of the driver private data in pcie_port_device_remove
but forgot to remove the old kfree from pcie_portdrv_remove.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pcie_port_device_remove currently calls the remove method of port
drivers twice. Ouch!
We are calling device_for_each_child multiple times for no apparent
reason.
So make it simple. Place put_device and device_unregister into
remove_iter, and throw out the rest. Only call device_for_each_child
once.
The code is simpler and actually works!
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
to the other API names in drivers/acpi/pci_root.c.
- Move _OSC related definitions to include/linux/acpi.h because _OSC
related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services. Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them. Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.
For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
