The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make use of memory resources rather than hardcoded IO adresses.
This is a first step towards DT support.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixed up a simple typo in the runtime sched_clock conversion
so we compile again.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes this build error:
arch/arm/mach-sa1100/nanoengine.c:75:11: error: 'PAGE_SHIFT' undeclared here (not in a function)
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Haâ– asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the include to fix things like this:
arch/arm/mach-sa1100/jornada720.c:278: error: 'PAGE_SHIFT' undeclared here (not in a function)
arch/arm/mach-bcmring/mm.c:32: error: 'PAGE_SHIFT' undeclared here (not in a function)
arch/arm/mach-sa1100/collie.c:361: error: 'PAGE_SHIFT' undeclared here (not in a function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Get rid of the mdesc pointer in the fixup function call. No one uses
the mdesc pointer, it shouldn't be modified anyway, and we can't wrap
it, so let's remove it.
Platform files found by:
$ regexp=$(git grep -h '\.fixup.*=' arch/arm |
sed 's!.*= *\([^,]*\),* *!\1!' | sort -u |
tr '\n' '|' | sed 's,|$,,;s,|,\\|,g')
$ git grep $regexp arch/arm
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the legacy ARM LED code for simpad devices and
register a stadard LED platform device using GPIO line
instead.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register keyboard, polled keyboard and I2C platform
devices based on GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- prepend CS3 accessors by simpad_ to indicate they
are specific to simpad devices.
- use spinlock to protect shadow register.
- implement 8 read-only pins.
- use readl/writel macros so barriers are used where
necessary.
- register CS3 as GPIO controller with 24 pins
(16 output only and 8 input only).
- fix PCMCIA driver to access the read-only pins
rather than the shadow register for status bits.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ucb1x00 GPIO definitions to simpad.h and add gpio_base
to ucb1x00 platform device so the pins are available using
the GPIO API.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This function is not used in the assabet build, and on the whole the
call is hard to consolidate so get rid of it from this machine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PCI nanoengine driver in the SA1100 machine probably has not
been building for some time. It probably dragged hardware.h
in implicitly and now it doesn't anymore. After this an SA1100
build selecting all system variants will build successfully.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert PCIBIOS_MIN_IO and PCIBIOS_MIN_MEM to variables to allow
multi-platform builds. This also removes the requirement for a platform to
have a mach/hardware.h.
The default values for i/o and mem are 0x1000 and 0x01000000, respectively.
Per Arnd Bergmann, other values are likely to be incorrect, but this commit
does not try to address that issue.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert pcibios_assign_all_busses from a define to inline so platforms can
control this setting.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
There are SoCs where attempting to enter a low power state is ignored,
and the CPU continues executing instructions with all state preserved.
It is over-complex at that point to disable the MMU just to call the
resume path.
Instead, allow the suspend finisher to return error codes to abort
suspend in this circumstance, where the cpu_suspend internals will then
unwind the saved state on the stack. Also omit the tlb flush as no
changes to the page tables will have happened.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The first and second arguments shouldn't concern platform code, so
hide them from each platforms caller.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need a veneer for cpu_suspend, it can be called directly from
C code now. Move it into sa11x0_pm_enter() along with the re-enabling
of clock switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we have core code dealing with CPU suspend/resume, we can
re-initialize the CPUs exception banked registers via that code rather
than having platforms deal with that level of detail. So, move the
call to cpu_init() out of platform code into core code.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_suspend() has a weird calling method which makes it only possible to
call from assembly code: it returns with a modified stack pointer to
finish the suspend, but on resume, it 'returns' via a provided pointer.
We can make cpu_suspend() appear to be a normal function merely by
swapping the resume pointer argument and the link register.
Do so, and update all callers to take account of this more traditional
behaviour.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is now taken care of by calling cpu_proc_init() in the resume
path, so eliminate this unnecessary call.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx, lpc32xx, mxc, netx, pxa, sa1100, tcc8k, tegra and u300
to use the generic mmio clocksource recently introduced.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update sa1100 clockevents code to reflect what its later derivative
does with clockevents_calc_mult_shift(). Use OSSR_M* constants too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than each platform providing its own function to adjust the
zone sizes, use the new ARM_DMA_ZONE_SIZE definition to perform this
adjustment. This ensures that the actual DMA zone size and the
ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS definitions are consistent with
each other, and moves this complexity out of the platform code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The values of ISA_DMA_THRESHOLD and MAX_DMA_ADDRESS are related; one is
the physical/bus address, the other is the virtual address. Both need
to be kept in step, so rather than having platforms define both, allow
them to define a single macro which sets both of these macros
appropraitely.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the sysdev class and struct sys_device used for power
management by the SA1100 interrupt-handling code with a
struct syscore_ops object which is simpler.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert sa11x0 to use the generic CPU suspend/resume support, rather
than implementing its own version. Tested on Assabet.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
locomo_info isn't actually used as a platform_data on collie platform:
arm/mach-sa1100/collie.c:237: warning: ‘locomo_info’ defined but not used
So locomo driver doesn't setup IRQs correctly. Pass locomo_info to the
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
Build errors similar this appeared in todays kautobuild for the above
targets:
In file included from arch/arm/include/asm/pgtable.h:461,
from arch/arm/mach-pxa/generic.c:26:
include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type
None of the .c files including asm/pgtable.h with this error is using
this header, so simply remove the include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace some magic numbers with constants and add interrupt definitions.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 7a5b4e16c8, simpad devices don't
boot anymore, since platform devices are registered too early. Fix by moving
the registration from map_io to arch_initcall as done on other sa1100 boards.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert sa1100 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nanoEngine's PCI support.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nanoEngine PCMCIA support, with support for two sockets.
In order to have a fully functional pcmcia subsystem in a BSE
nanoEngine board you should carefully read this:
http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes checkpatch.pl issues in
arch/arm/mach-sa1100/cpu-sa1110.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds Bright Star Engineering's nanoEngine board support to the kernel.
Also:
- Adds the nanoEngine memory chip to arch/arm/mach-sa1100/cpu-sa1110.c
(Micron MT48LC8M16A2TG-75).
- Increase in the sdram_params->name[] field length to accomodate the
name of the memory chip.
- Clean up of header content and order of
arch/arm/mach-sa1100/cpu-sa1110.c
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes checkpatch.pl issues in arch/arm/mach-sa1100/cpu-sa1100.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: mach-sa1100: Fix for compiler warning of uninitialized variable.
This is a fix for the compiler warning: 'new_ppcr' may be used
uninitialized in this function.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
SHARP_LOCOMO doesn't exist in Kconfig, therefore replacing all
references for it with SHARP_LOCOMO in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-sa1100/leds.c:21: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:21: WARNING: please, no space before tabs
arch/arm/mach-sa1100/leds.c:22: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:22: WARNING: please, no space before tabs
arch/arm/mach-sa1100/leds.c:24: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:24: WARNING: please, no space before tabs
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Just to make sure that this driver won't run on StrongArm SA1100
when both SA1100 and SA1110 cpufreq drivers are built in (usually
in multimachine config). SA1100 driver already has similar check.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
They have StrongARM SA1110, not SA1100.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
A pointer to a probe callback is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Cc: Paul Sokolovsky <pmiscml@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These functions are called with irqs already off. This commit removes
the calls to raw_local_irq_save and raw_local_irq_restore on platforms
that don't have to use a shared interrupt for their timekeeping.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fix:
arch/arm/mach-sa1100/generic.c:117: error: redefinition of 'cpufreq_get'
include/linux/cpufreq.h:299: error: previous definition of 'cpufreq_get' was here
cpufreq_get() is used on these platforms to tell drivers what the CPU
frequency is, and therefore the bus frequency - which is critical for
setting the PCMCIA and LCD timings. Adding ifdefs to these drivers to
select cpufreq_get() or some other interface adds confusion. Making
these drivers use some other interface for the normal paths and cpufreq
stuff for the cpufreq notifier is insane as well.
(Why x86 can't provide a version of cpufreq_get() which returns the
CPU frequency when CPUFREQ is disabled is beyond me, rather than
requiring a dummy zero-returning cpufreq_get(). Especially as they
do:
unsigned long khz = cpufreq_get(cpu);
if (!khz)
khz = tsc_khz;
In other words, if CPUFREQ is disabled, get it from tsc_khz - why
not provide a dummy cpufreq_get() which returns tsc_khz?)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many features of h3100/h3600 (LCD, PCMCIA, Flash write, etc.)
depend on correct functioning of GPIO expander handled by htc-egpio
driver, so force its building in Kconfig.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for "Power" and "Action" (joystick center) buttons -
the only buttons on iPaq h3100/h3600 connected to GPIOs
(other buttons are controlled by microcontroller)
Also remove setting PWER for wakeup on Power button press -
gpio-keys driver will handle it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After a code reorganization and following split, there's some #includes
now unused. Clean them up and sort remaining alphabetticaly where possible.
Compile tested.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct boilerplates after files split. Also shorten them a bit - use
standart GPL wording (as per http://lkml.org/lkml/2007/5/1/220) and
drop changelog, which only entry about h3800 support and abstracted
EGPIOs is just confusing now, as both of these features are gone.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split common h3600.c into three separate files: h3100.c, h3600.c and
h3xxx.c (the latter contains common code for h3100/h3600)
Copyright boilerplates and #includes are copied intact and will be
cleaned up later.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine both headers into one, rename to h3xxx.h and change all
users accordingly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all existing code was converted to gpiolib, drop no more
used pre-gpiolib (bit-shifted) GPIO definintions.
Supply new gpiolib-friendly definitions for GPIOs which
don't have them yet.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.
Drop this initialisation and configure all GPIOs as input.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all the remaining users of these definitions
(in pcmcia/sa1100_h3600 driver) were converted to gpio_to_irq(),
they can be safely removed.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all users of assign_h3600_egpio now converted to gpiolib, we
can safely remove all assign_h3600_egpio handling code and
definitions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It will be used for future conversion of assign_h3600_egpio calls to
gpiolib.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
h3100 and h3600 have different sets of LCD-controlling gpios,
which mapped to the same "abstracted" EGPIO.
As we plan to get rid of those abstracted egpios completely, we
need to separate these helper functions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM_SUSPEND, PM_RESUME and machine_is_h3xxx() are not used anywhere in
kernel (checked with git grep), so it's safe to remove them.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRDA is handled by separate sa1100-ir driver and has
nothing to do with sa1100_serial
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No point calling sa1100_register_uart_fns early - these aren't
used until late in the boot sequence. Also convert to gpiolib
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both iPaqs h3100 and h3600 currently share the same source
file - h3600.c But Makefile builds it only if CONFIG_SA1100_H3600
selected, so selecting just CONFIG_SA1100_H3100 results in
"no machine record defined" message and aborted compilation.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed unused CONFIG SA1100_H3XXX from Kconfig and defconfig
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
8e19608 missed updating SA11x0, and thus:
arch/arm/mach-sa1100/time.c:88: warning: initialization from incompatible pointer type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file was never enabled in the mainline kernel, new ongoing work on
battery driver by Thomas Kunze makes it completely obsolete, so remove
it now.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Start converting scoop gpio access to new API instead of old
deprecated one.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since now ipaq_model_ops used only for accessing h3600 EGPIOs,
drop it completely and use assign_h3600_egpio() directly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace all occurences with assign_h3600_egpio.
Also simplify code a bit by replacing couple of if-else
statements with one-line equivalents.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unused fields and associated funtions-accesors.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Right now iPaq h3600's default MTD partitions table is a mess. It has
two #ifdefs with #else, giving total 3 variants, depending on your
kernel config. Replace all this with simple two-partitions scheme
(bootloader + rootfs), that used by both shipped WindowsCE and
most of the linux distributions (Familiar, Angstrom)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no actual code for iPAQ sleeves support in kernel that depends
on this config option.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Code has never been in buildable state since initial
merge.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the list of devices activated at init
to also include the keyboard and touchscreen structs.
We also remove a non-needed #ifdef.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.
Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
This patch fixes bad formatting found in
mach-sa1100 files.
What it does is to replace/delete things like
excessive spaces (start || endline). The code
looks the same just alot less junk.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both of these symbols should be defined by a platform, or neither
should be defined. Ensure that all platforms conform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Continuing the move away from implementations which give an excuse
for other bad implementations, convert SA1100 to lookup its singular
clock by dev_name(dev) rather than by id.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It has been dead for more than 3 years and needs to be converted
to use platform PATA support anyway.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes formatting issues in mach-sa1100/
machine files. More specificly badge4.c,generic.c and
pleb.c.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move asm-arm/cnt32_to_63.h to include/linux/ so that MN10300 can make
use of it too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Adds ssp functions into header so we don't get
"implicit declaration" error at builtime.
* Converts jornada_ssp_start/end functions into voids with
proper declarations (to avoid "prototype..." warning).
* Sorts include files in alphabetical order
* Minor comment changes
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the commented out line for the not available
CONFIG_SA1100_USB option.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to the problem of reset status bits being handled by different
registers between pxa2xx and pxa3xx, introduce a global reset_status
variable, initialized by SoC-specific code and later being used by
other drivers.
And also introduce clear_reset_status(), which is used to clear the
corresponding status bits. Pass RESET_STATUS_ALL to clear all bits.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch uses the ability of PXA's clocklib to alias clock to resolve the
problem caused by sharing the SA1111 IO controller between PXA and SA1100
architectures, which have differing GPIO numbering.
Signed-off-by: Ian Molton <spyro@f2s.com>
collie.h:
* add some meaningfull names to some gpios
collie.c:
* initialize cpu registers correctly
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Each time a pxa type cpu went in suspend, a portion of
kmalloc memory was corrupted.
The issue was an incorrect length allocation introduced by
the commit 711be5ccfe for
the save registers array (=> overflow).
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
d142b6e77d added clock source support,
now it's time for the clock event support.
Tested-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
Warning message :
WARNING: vmlinux.o(.text+0x9afc): Section mismatch: reference to .init.text:sa1110_mb_enable (between 'sa1111_probe' and 'sa1111_remove')
WARNING: vmlinux.o(.text+0x13b1ac): Section mismatch: reference to .init.text:pcmcia_jornada720_init (between 'pcmcia_probe' and 'pcmcia_remove')
* fixes the 'section mismatch' building warnings for target sa1100. Solution is __init -> __devinit. Thanks to Randy Dunlap for pointing out the solution.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().
This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mach-integrator/pci_v3.c: no need to reference 'irq' arg, its constant
mach-omap1/pm.c: remove extra whitespace
arch/arm/mach-sa1100/ssp.c: remove braces around single C stmt
arch/arm/plat-omap/mcbsp.c:
- remove pointless casts from void*
- make longer lines more readable
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Â Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. Â In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This fixes the jornada720.c file :
* ifdef for CONFIG_SA1100_JORNADA720_SSP since we dont want to include anything not selected in menyconfig.
* add documentation for init for future reference
* change platform driver name from jornada720_mcu ->
jornada_ssp.
* change maintainer in file.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These patches add full SSP/MCU support for the HP Jornada 720
machine. Its needed to handle keyboard, touchscreen, battery
and backlight/lcd.
The main driver exports functions and the header file exports
the command values. When talking to the MCU the general procedure
is to start MCU, send command (using ssp_inout(command)), the
proper reply is always TXDUMMY. After receiving TXDUMMY you can
send the value you wish pushed (for example brightness level).
End with ssp_end() so the spinlock gets unlocked.
Drivers using this havent been implemented yet, but will shortly.
Signed-off-by: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the RTC management over a suspend/resume cycle. As per the
corresponding PXA patch, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The saved_state member of 'struct dev_pm_info' that's going to be removed
is used in arch/arm/common/locomo.c, arch/arm/common/sa1111.c and
arch/arm/mach-sa1100/neponset.c. Change the code in there to use local
variables for saving the state of devices during suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a mutex in the sa1100 clock support rather than a semaphore.
Remove the unused "module" field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers. Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Build fix: sa1100/generic.c should already have included <asm/gpio.h>,
but it didn't ... causing a build problem with a recent patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/241),
this patch
- adds gpio_direction_input/output functions to
generic.c instead of making them inline,
- fixes comment and includes and uses inline functions
instead of macros in gpio.h
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel/built-in.o: In function `pm_suspend':
utsname_sysctl.c:(.text+0x23008): multiple definition of `pm_suspend'
arch/arm/mach-sa1100/built-in.o:arch/arm/mach-sa1100/sleep.S:(.text+0xf68): first defined here
arm-linux-ld: Warning: size of symbol `pm_suspend' changed from 20 in arch/arm/mach-sa1100/built-in.o to 44 in kernel/built-in.o
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* HP Jornada 720 uses epson 1356 chip for graphics. This chip is compatible with s1d13xxxfb driver.
* HP Jornada 720 uses a Microprocessor Control Unit to talk to various
hardware. We add it as a platform device in jornada720_init()
* We provide pm_suspend() to avoid unresolved symbols in apm.o. We are
unable to truly suspend now, hence the stub.
* Speaker/microphone enabling got removed because it will be placed in the alsa driver.
Signed-off-by: Filip Zyzniewski <(address hidden)>
Signed-off-by: Kristoffer Ericson <(address hidden)>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge:
Atmel AT91RM9200 and AT91SAM9260 changes
General ARM developments
Disconfiguous memory cleanups
64-bit/32-bit division and sched_clock extension patches
EP93xx support changes
IOP support changes
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This provides a 63 bit clock counter guaranteed to be monotonic over a
period of 370 days instead of a clock wrap every 19.4 minutes, as long
as sched_clock() is called at least once every 9.7 minutes which
shouldn't be a problem in practice.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't reset OSCR to zero as this prevents us from having a contiguous
time source. The value returned by sched_clock() is reset to zero in the
middle of the boot process otherwise, making CONFIG_PRINTK_TIME rather
messed up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"K4S281632b-1H" should read "K4S281632B-1H" (As it does everywhere
else). No more coffe!
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds correct sdram params for K4S281632B-1H and sets the jornada to use them by default.
Signed-off-by: Kristoffer Ericson
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Convert LOMOMO to use struct device * for GPIOs instead of struct
locomo_dev. This enables access to the GPIOs from code which is not
a locomo device itself (such as audio). Access for gpio 31 is removed
for error handling (no such hardware exists).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
