Ensure that the uart clock is enabled prior to writing to the
interrupt mask register in s3c24xx_serial_resume_noirq function.
Without enabing the uart clock, the uart register cannot be accessed.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the Exar specific codes from 8250_pci and blacklist those chips
so that the new Exar serial driver binds to the devices.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the serial driver for the Exar chips. And also register the
platform device for the GPIO provided by the Exar chips.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace passes the SER_RS485_RTS_ON_SEND flag it means that the
CTS_B pin should go to logic level high before the transmission begins.
CTS_B goes to logic level high when both CTSC and CTS bits are cleared.
When userspace passes the SER_RS485_RTS_AFTER_SEND flag it means that the
CTS_B pin should go to logic level low after the transmission finishes.
CTS_B goes to logic level low when CTSC bit is cleared and CTS bit is set.
So fix the CTS_B polarity logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a board that needs to drive RTS GPIO high in order to enable the
transmission of a RS485 transceiver the following description is
passed in the devide tree:
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
rts-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
status = "okay";
};
and userspace configures the uart port as follows:
/* enable RS485 mode: */
rs485conf.flags |= SER_RS485_ENABLED;
/* set logical level for RTS pin equal to 1 when sending: */
rs485conf.flags |= SER_RS485_RTS_ON_SEND;
/* set logical level for RTS pin equal to 0 after sending: */
rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND);
However the RTS GPIO polarity observed in the oscilloscope is inverted.
When the SER_RS485_RTS_ON_SEND flag is set the imx_port_rts_active()
function should be called and following the same logic when
SER_RS485_RTS_AFTER_SEND flag is cleared the imx_port_rts_inactive()
should be called.
Do such logic change so that RS485 communication in half duplex can
work successfully when the RTS GPIO pin is passed via device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During build testing, I ran into a warning in a driver that I
had written myself at some point:
drivers/tty/serial/8250/8250_of.c: In function 'of_platform_serial_probe':
drivers/tty/serial/8250/8250_of.c:233:1: error: the frame size of 1200 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
This is harmless by itself, but it shows two other problems in
the driver:
- It still tries to be generic enough to handle all kinds of serial
ports, where in reality the driver has been 8250-only for a while,
and every other uart has its own DT support
- As a result of that generalization, we keep two copies of
'struct uart_port' on the stack during probe(). This is completely
unnessary.
Removing the last code dealing with unsupported port_type values
solves both problems nicely, and reduces the stack size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the function header of sci_parse_dt() is split in an unusual way,
"git diff" gets confused when changes to the body of the function are
made, and attributes them to the wrong function.
Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new callback is in preparation for persistent scrollback buffer
support for VGA consoles.
With a single scrollback buffer for all consoles, we could flush the
buffer just by invocating consw->con_switch(). But when each VGA console
has its own scrollback buffer, we need a new callback to tell the
video console driver which buffer to flush.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Andrey Utkin <andrey_utkin@fastmail.com>
Tested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this warning is triggered for allmodconfig on m68k. It is
well intentioned, in that if you are building the driver but not
enabling one of the platforms where the hardware exists, you get a
warning.
The warning dates back to pre-git days, and now we have COMPILE_TEST
so we can use that to mask the warning for people who are obviously
just doing build coverage on tree wide changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds xilinx uart loopback support by modifying the
cdns_uart_set_mctrl function to handle the switch to loopback mode.
After this patch, the loopback mode can be enabled/disabled by
setting/clearing the TIOCM_LOOP modem bit via TIOCMBIS/TIOCMBIC
ioctls respectively.
Signed-off-by: Yasir-Khan <yasir_khan@mentor.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to work with the client operations which uses const ptrs.
Really, the flags pointer could be const, too, but this would be a tree
wide fix.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_register_device is just a wrapper for tty_register_device_attr with
NULL passed for drvdata and attr_grp. So similarly make
tty_port_register_device a wrapper of tty_port_register_device_attr so that
additions don't have to be made in both functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let us create tty objects entirely in kernel space. Untested proposal to
show why all the ideas around rewriting half the uart stack are not needed.
With this a kernel created non file backed tty object could be used to handle
data, and set terminal modes. Not all ldiscs can cope with this as N_TTY in
particular has to work back to the fs/tty layer.
The tty_port code is however otherwise clean of file handles as far as I can
tell as is the low level tty port write path used by the ldisc, the
configuration low level interfaces and most of the ldiscs.
Currently you don't have any exposure to see tty hangups because those are
built around the file layer. However a) it's a fixed port so you probably
don't care about that b) if you do we can add a callback and c) you almost
certainly don't want the userspace tear down/rebuild behaviour anyway.
This should however be sufficient if we wanted for example to enumerate all
the bluetooth bound fixed ports via ACPI and make them directly available.
It doesn't deal with the case of a user opening a port that's also kernel
opened and that would need some locking out (so it returned EBUSY if bound
to a kernel device of some kind). That needs resolving along with how you
"up" or "down" your new bluetooth device, or enumerate it while providing
the existing tty API to avoid regressions (and to debug).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vendor driver allows setting baud-rates higher than 115200 baud.
There is a check in the vendor driver which prevents using more than
115200 baud during startup, however it does not have such a check in
.set_termios.
Higher baud-rates are often used by the bluetooth modules embedded into
the SDIO wifi chips (Amlogic devices use brcmfmac based wifi chips quite
often, 2000000 baud seems to be a common value for the UART baud-rate in
Amlogic's "libbt").
I have tested this on a Meson GXL device with uart_A (to which the
bluetooth module is connected, where initialization times out with
115200 baud) and uart_AO (which I manually set to 2000000 baud and then
connected with my USB UART adapter to that).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For in-kernel tty users, we need to be able to create and destroy
'struct tty' that are not associated with a file. The creation side is
fine, but tty_release() needs to be split into the file handle portion
and the struct tty portion. Introduce a new function, tty_release_struct,
to handle just the destroying of a struct tty.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT earlycon for omap_serial driver. This boot console is included
with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y, CONFIG_SERIAL_OMAP=y, and
CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exactly as in a80c49db ("serial8250: Mark console as CON_ANYTIME"),
to enable printk() during CPU hot-plugging.
Actually most of the serial console drivers do not use per-cpu resources
and can be marked as CON_ANYTIME.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for blackfin architecture.
File size before:
text data bss dec hex filename
3572 320 16 3908 f44 tty/serial/bfin_sport_uart.o
File size after:
text data bss dec hex filename
3664 228 16 3908 f44 tty/serial/bfin_sport_uart.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to set PCI bus mastering when device is not doing any DMA. It
includes MSI type of interrupts. Currently only UART on Denverton, which is DMA
capable, might have MSI enabled.
Taking above into account enable bus mastering for Denverton case only.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable MSI type of interrupt if PCI BIOS supports it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the most common use case, the Synopsys DW UART driver does not
set the set_termios callback function. This prevents UPSTAT_AUTOCTS
from being set when the UART flag CRTSCTS is set. As a result, the
driver will use software flow control as opposed to hardware flow
control.
To fix the problem, the set_termios callback function is set to the
DW specific function. The logic to set UPSTAT_AUTOCTS is moved so
that any clock error will not affect setting the hardware flow
control.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCI instances found in SH SoCs have different spacing between registers
depending on the SoC. The platform data contains a regshift field that
tells the driver by how many bits to shift the register offset to
compute its address. We can compute the regshift value automatically
based on the memory resource size, there's no need to pass the value
through platform data.
Fix the sh7750 SCI and sh7760 SIM port memory resources length to ensure
proper computation of the regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field isn't set by any platform but is only used internally in the
driver to hold data parsed from DT. Move it to the sci_port structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci driver implements manual break debouncing for a few SH
platforms by reading the value of the RX pin port register. This feature
is optional and the driver considers all negative or zero values of the
platform data port_reg field as invalid. As the four platforms that set
the field to a register address all use an address higher than
0x7fffffff, the driver will always consider the value as invalid and
never perform debouncing. The feature is unused, remove it.
Debouncing could be implemented properly in the future using the pinctrl
and GPIO APIs if desired.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only SH platforms still use platform data for the sh-sci, and none of
them declare DMA channels connected to the SCI. Remove the corresponding
platform data fields and simplify the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo size, overrun register and mask, sampling rate mask and error
mask all depend on the port type only and don't need to be computed at
runtime. Add them to the sci_port_parameters structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver modifies platform data for internal purpose only. Fix that
and make the platform data structure const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn the regmap two-dimensional array to an array of port parameters and
store a pointer to the port parameters in the sci_port structure. This
will allow handling additional port type dependent parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UPF_BOOT_AUTOCONF platform data flag is set by all platforms,
hardcode it.
The UPF_IOREMAP flag is set by a single SH platform and thus needs to be
kept. However, for ARM platforms, we can base the decision on whether an
OF node is present and bypass the platform data flags completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Transmit Enable and Receive Enable bits are set in the scscr field
of all instances of the sh-sci platform data. Set them in the driver
directly to prepare for their removal from platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a nasty interface and setting the state of a foreign task must
not be done. As of the following commit:
be628be095 ("bcache: Make gc wakeup sane, remove set_task_state()")
... everyone in the kernel calls set_task_state() with current, allowing
the helper to be removed.
However, as the comment indicates, it is still around for those archs
where computing current is more expensive than using a pointer, at least
in theory. An important arch that is affected is arm64, however this has
been addressed now [1] and performance is up to par making no difference
with either calls.
Of all the callers, if any, it's the locking bits that would care most
about this -- ie: we end up passing a tsk pointer to a lot of the lock
slowpath, and setting ->state on that. The following numbers are based
on two tests: a custom ad-hoc microbenchmark that just measures
latencies (for ~65 million calls) between get_task_state() vs
get_current_state().
Secondly for a higher overview, an unlink microbenchmark was used,
which pounds on a single file with open, close,unlink combos with
increasing thread counts (up to 4x ncpus). While the workload is quite
unrealistic, it does contend a lot on the inode mutex or now rwsem.
[1] https://lkml.kernel.org/r/1483468021-8237-1-git-send-email-mark.rutland@arm.com
== 1. x86-64 ==
Avg runtime set_task_state(): 601 msecs
Avg runtime set_current_state(): 552 msecs
vanilla dirty
Hmean unlink1-processes-2 36089.26 ( 0.00%) 38977.33 ( 8.00%)
Hmean unlink1-processes-5 28555.01 ( 0.00%) 29832.55 ( 4.28%)
Hmean unlink1-processes-8 37323.75 ( 0.00%) 44974.57 ( 20.50%)
Hmean unlink1-processes-12 43571.88 ( 0.00%) 44283.01 ( 1.63%)
Hmean unlink1-processes-21 34431.52 ( 0.00%) 38284.45 ( 11.19%)
Hmean unlink1-processes-30 34813.26 ( 0.00%) 37975.17 ( 9.08%)
Hmean unlink1-processes-48 37048.90 ( 0.00%) 39862.78 ( 7.59%)
Hmean unlink1-processes-79 35630.01 ( 0.00%) 36855.30 ( 3.44%)
Hmean unlink1-processes-110 36115.85 ( 0.00%) 39843.91 ( 10.32%)
Hmean unlink1-processes-141 32546.96 ( 0.00%) 35418.52 ( 8.82%)
Hmean unlink1-processes-172 34674.79 ( 0.00%) 36899.21 ( 6.42%)
Hmean unlink1-processes-203 37303.11 ( 0.00%) 36393.04 ( -2.44%)
Hmean unlink1-processes-224 35712.13 ( 0.00%) 36685.96 ( 2.73%)
== 2. ppc64le ==
Avg runtime set_task_state(): 938 msecs
Avg runtime set_current_state: 940 msecs
vanilla dirty
Hmean unlink1-processes-2 19269.19 ( 0.00%) 30704.50 ( 59.35%)
Hmean unlink1-processes-5 20106.15 ( 0.00%) 21804.15 ( 8.45%)
Hmean unlink1-processes-8 17496.97 ( 0.00%) 17243.28 ( -1.45%)
Hmean unlink1-processes-12 14224.15 ( 0.00%) 17240.21 ( 21.20%)
Hmean unlink1-processes-21 14155.66 ( 0.00%) 15681.23 ( 10.78%)
Hmean unlink1-processes-30 14450.70 ( 0.00%) 15995.83 ( 10.69%)
Hmean unlink1-processes-48 16945.57 ( 0.00%) 16370.42 ( -3.39%)
Hmean unlink1-processes-79 15788.39 ( 0.00%) 14639.27 ( -7.28%)
Hmean unlink1-processes-110 14268.48 ( 0.00%) 14377.40 ( 0.76%)
Hmean unlink1-processes-141 14023.65 ( 0.00%) 16271.69 ( 16.03%)
Hmean unlink1-processes-172 13417.62 ( 0.00%) 16067.55 ( 19.75%)
Hmean unlink1-processes-203 15293.08 ( 0.00%) 15440.40 ( 0.96%)
Hmean unlink1-processes-234 13719.32 ( 0.00%) 16190.74 ( 18.01%)
Hmean unlink1-processes-265 16400.97 ( 0.00%) 16115.22 ( -1.74%)
Hmean unlink1-processes-296 14388.60 ( 0.00%) 16216.13 ( 12.70%)
Hmean unlink1-processes-320 15771.85 ( 0.00%) 15905.96 ( 0.85%)
x86-64 (known to be fast for get_current()/this_cpu_read_stable() caching)
and ppc64 (with paca) show similar improvements in the unlink microbenches.
The small delta for ppc64 (2ms), does not represent the gains on the unlink
runs. In the case of x86, there was a decent amount of variation in the
latency runs, but always within a 20 to 50ms increase), ppc was more constant.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: mark.rutland@arm.com
Link: http://lkml.kernel.org/r/1483479794-14013-5-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch effectively replaces the tsk pointer dereference
(which is obviously == current), to directly use get_current()
macro. This is to make the removal of setting foreign task
states smoother and painfully obvious. Performance win on some
archs such as x86-64 and ppc64 -- arm64 is no longer an issue.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mark.rutland@arm.com
Link: http://lkml.kernel.org/r/1483479794-14013-3-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds a new UART port type for TI DA8xx/OMAPL13x/AM17xx/AM18xx/66AK2x.
These SoCs have standard 8250 registers plus some extra non-standard
registers.
The UART will not function unless the non-standard Power and Emulation
Management Register (PWREMU_MGMT) is configured correctly. This is
currently handled in arch/arm/mach-davinci/serial.c for non-device-tree
boards. Making this part of the UART driver will allow UART to work on
device-tree boards as well and the mach code can eventually be removed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
This is even more problematic when said option selects other options.
You end up with several device drivers forcibly built into the kernel.
In this specific case, drivers 8250_mid, virt-dma, hsu_dma and
hsu_dma_pci end up being built-in as soon as SERIAL_8250=y. It is
very common for distribution kernels to build the subsystem core code
into the kernel, because almost everybody will need it, but build all
the device drivers as modules. This should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_MID visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 1fc969c759 ("serial: 8250_mid: make module available only on X86")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
This is even more problematic when said option selects other options.
You end up with several device drivers forcibly built into the kernel.
In this specific case, drivers 8250_lpss, dw_dmac_core and
dw_dmac_pci end up being built-in as soon as SERIAL_8250=y. It is
very common for distribution kernels to build the subsystem core code
into the kernel, because almost everybody will need it, but build all
the device drivers as modules. This should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_LPSS visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a13e19cf3d ("serial: 8250_lpss: split LPSS driver to separate module")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hiding tristate options with "if EXPERT" is usually not a good idea.
You can decide that the driver should be included by default, but you
don't know if the user wants it built-in or as a module. Hiding the
option prevents the user from making that decision.
In this specific case, driver 8250_pci ends up being built-in as soon
as SERIAL_8250=y. It is very common for distribution kernels to build
the subsystem core code into the kernel, because almost everybody
will need it, but build all the device drivers as modules. This
should be made possible.
So drop the "if EXPERT" and make SERIAL_8250_PCI visible.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CONFIG_DYNAMIC_DEBUG if dyndbg enables debug output in
8250_port.c deadlock happens inevitably on UART IRQ handling.
That's the problematic execution path:
---------------------------->8------------------------
UART IRQ:
serial8250_interrupt() ->
serial8250_handle_irq(): lock "port->lock" ->
pr_debug() ->
serial8250_console_write(): bump in locked "port->lock".
OR (if above pr_debug() gets removed):
serial8250_tx_chars() ->
pr_debug() ->
serial8250_console_write(): bump in locked "port->lock".
---------------------------->8------------------------
So let's get rid of those not that much useful debug entries.
Discussed problem could be easily reproduced with QEMU for x86_64.
As well as this fix could be mimicked with muting of dynamic debug for
the problematic lines as simple as:
---------------------------->8------------------------
dyndbg="+p; file 8250_port.c line 1756 -p; file 8250_port.c line 1822 -p"
---------------------------->8------------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Phillip Raffeck <phillip.raffeck@fau.de>
Cc: Anton Wuerfel <anton.wuerfel@fau.de>
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'request_irq()' and 'free_irq()' should be called with the same dev_id.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/devicetree/bindings/serial/serial.txt the
generic 'rts-gpios' property can be used to specify the GPIO for RTS
functionality.
Currently it is not possible to use the imx UART port in rs485 mode when
the 'rts-gpios' property is passed in the device tree.
The imx uart driver only checks for the presence of the built-in RTS pin,
via 'uart-has-rtscts' property and disable the rs485 flag if this property
is absent.
So fix this logic by also checking if RTS pin has been passed via GPIO.
Tested on a imx6dl based board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a follow up to the commit a9b01b5823 ("serial: 8250_mid fix calltrace
when hotplug 8250 serial controller") in which the kernel crash was described
for another 8250 based driver. It appears that we have the very same issue in
8250_lpss. Fix it by unregistering serial driver first.
Cc: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$
After this patch:
$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
alias: of:N*T*Cqcom,msm-uartdmC*
alias: of:N*T*Cqcom,msm-uartdm
alias: of:N*T*Cqcom,msm-uartC*
alias: of:N*T*Cqcom,msm-uart
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When struct moxa8250_board is allocated, then num_ports should
be initialized in order to use it later in moxa8250_remove.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add resource type check for Fintek F81504/508/512, BAR3/4/5 must be
IORESOURCE_IO.
Fintek is trying to make F81504/508/512 works on MMIO interface, but
it's still in progress. We found some issue when the experiment IC
when the BAR3/4/5 is IORESOURCE_MEM. It'll cause wrong operation with
IO resource. So we'll add the resource check for this.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows enabling earlycon for devices with a Lantiq serial console
by splitting lqasc_serial_port_write() from lqasc_console_write() and
re-using the new function for earlycon's write callback.
The kernel-parameter name matches the driver name ("lantiq"), similar
to how other drivers implement this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'request_irq' and 'free_irq' should have the same 'dev_id'.
Here one uses 'port', and the other one uses 'sport'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_request_slave_channel_compat() requires filter function and mask, which
are not needed on device tree based platforms, so simplify the code by
calling the more appropriate dma_request_chan() function. This additionally
gives us proper error handling, because the new function returns error
codes instead of NULL on failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CMSPAR is set in the c_cflag of termios, "stick" parity is enabled.
Tested on an i.MX28 system
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New IC MAX14830 has 0xB4 silicon revision ID.
This patch adds support for such ICs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem found via lockdep:
- lpuart_set_termios() calls del_timer_sync(&sport->lpuart_timer) while
holding sport->port.lock
- sport->lpuart_timer routine is lpuart_timer_func() that calls
lpuart_copy_rx_to_tty() that acquires same lock.
To fix, move Rx DMA stopping out of lock, as it already is in other places
in the same file.
While at it, also make Rx DMA start/stop code to look the same is in
other places in the same file.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the call to kasprintf() returns a NULL pointer, function
sci_request_irq() frees the preallocated memory and returns 0 is
returned. Because 0 means no error, the caller of sci_request_irq()
will keep going, and the freed memory may be used or freed again. To
avoid the above issue, this patch assigns "-ENOMEM" to the return
variable ret.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188691
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit needs to be reverted because it prevents people from
using the serial console as a secondary console with input being
directed to tty0.
IOW, if you boot with console=ttyS0 console=tty0 then all kernels
prior to this commit will produce output on both ttyS0 and tty0
but input will only be taken from tty0. With this patch the serial
console will always be the primary console instead of tty0,
potentially preventing people from getting into their machines in
emergency situations.
Fixes: d03516df83 ("tty: serial: 8250: add CON_CONSDEV to flags")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in RS485 emulation mode, __do_stop_tx_rs485() calls
serial8250_clear_fifos(). This not only clears the FIFOs, but also sets
all bits in their control register (UART_FCR) to 0.
One of the effects of this is the disabling of the FIFOs, which turns
them into single-byte holding registers. The rest of the driver doesn't
know this, which results in the lions share of characters passed into a
write call to be dropped.
(I can supply logic analyzer screenshots if necessary)
This fix replaces the serial8250_clear_fifos() call to
serial8250_clear_and_reinit_fifos() - this prevents the "dropped
characters" issue from manifesting again while retaining the requirement
of clearing the RX FIFO after transmission if the SER_RS485_RX_DURING_TX
flag is disabled.
Signed-off-by: Daniel Jedrychowski <avistel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc ("serial: 8250_pci: Detach low-level driver during
PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RS485 in half duplex, RX should be enabled when TX is
finished, and stopped when TX starts.
Before commit 0058f0871e ("tty/serial: atmel: fix RS485 half
duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA
was used. So, collisions could happened.
But disabling RX in atmel_start_tx() uncovered another bug:
RX was enabled again in the wrong place (in atmel_tx_dma) instead of
being enabled when TX is finished (in atmel_complete_tx_dma), so the
transmission simply stopped.
This bug was not triggered before commit 0058f0871e
("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was
never disabled before.
Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem.
Cc: stable@vger.kernel.org
Reported-by: Gil Weber <webergil@gmail.com>
Fixes: 0058f0871e
Tested-by: Gil Weber <webergil@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we don't disable the transmitter in atmel_stop_tx, the DMA buffer
continues to send data until it is emptied.
This cause problems with the flow control (CTS is asserted and data are
still sent).
So, disabling the transmitter in atmel_stop_tx is a sane thing to do.
Tested on at91sam9g35-cm(DMA)
Tested for regressions on sama5d2-xplained(Fifo) and at91sam9g20ek(PDC)
Cc: <stable@vger.kernel.org> (beware, this won't apply before 4.3)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYUg7NAAoJEHwUBw8lI4NH5/gP/j81+2RzCUX8PiLQxNUt0Vj+
tVJEizpWCwN1cnhc8ibZdI1DAwyj+GbN2lghYTjqqEng4yOm3czPzUl99grBrpQl
t+Qylr9PSpck/paRhd2lgZzG8Nk+B5HJDcxBQbW4pwmbc69YAbqYzt44i4bDpR5K
u3mBve1Ulng7peP45EZB8BA32ffCpOEAC/9SdkaPokrSv6XxxPEFvzewy+mLtioU
a0zY0iuHqVGpOTABK65fXO/zkGiZLPXJ1T5vK7Iz8mOwuvtYVif0yktQSrx3BWbc
9r64W7Si633wWt/C9LkuMMSmQ7nI/PyHk811cDOcxp3SA79JV5SWwdQl+5QPdtoP
hyToaISfAY0BiNI9ltdscx3MPjlwSp08xXvi46RjSs8E2TXnbHUw+J5mTsxYuocl
Yi61nlL5ClhCbySf9Q3GFsuAJ3O2Nq9WkCTNRIvJtrMhe3NeqDDTfBZJRD4Bfg1G
q8RAc5oqGZDtqKHtLfwULr7Ec2Ru0hIZAyN907OwW+4jBR/eBJB1y+nGrNPtTWPT
OOcvrxe85/+ZNROGCZKr0L8UA/MBBMZtjvMY8RMXjBE4YJbakq7tV+7l5VolKeNH
G6I/1CC06qVPHrnetM6YejhtnmOQ4F8P1sE0wvpG0QTyHJoFq+aOhHNKJC8F9Eln
CQM2apvL4BHvS7OHt9XL
=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Pull workqueue updates from Tejun Heo:
"Mostly patches to initialize workqueue subsystem earlier and get rid
of keventd_up().
The patches were headed for the last merge cycle but got delayed due
to a bug found late minute, which is fixed now.
Also, to help debugging, destroy_workqueue() is more chatty now on a
sanity check failure."
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: move wq_numa_init() to workqueue_init()
workqueue: remove keventd_up()
debugobj, workqueue: remove keventd_up() usage
slab, workqueue: remove keventd_up() usage
power, workqueue: remove keventd_up() usage
tty, workqueue: remove keventd_up() usage
mce, workqueue: remove keventd_up() usage
workqueue: make workqueue available early during boot
workqueue: dump workqueue state on sanity check failures in destroy_workqueue()
Here's the tty/serial patchset for 4.10-rc1.
It's been a quiet kernel cycle for this subsystem, just a small number
of changes. A few new serial drivers, and some cleanups to the old
vgacon logic, and other minor serial driver changes as well.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAwDQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylcngCgko5+aPLnHENLNIaHhHlfdMbhy+EAn2H8wkzY
bEf+BG4CJDb6nZWERcUQ
=STpQ
-----END PGP SIGNATURE-----
Merge tag 'tty-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the tty/serial patchset for 4.10-rc1.
It's been a quiet kernel cycle for this subsystem, just a small number
of changes. A few new serial drivers, and some cleanups to the old
vgacon logic, and other minor serial driver changes as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (54 commits)
serial: 8250_mid fix calltrace when hotplug 8250 serial controller
console: Move userspace I/O out of console_lock to fix lockdep warning
tty: nozomi: avoid sprintf buffer overflow
serial: 8250_pci: Detach low-level driver during PCI error recovery
serial: core: don't check port twice in a row
mxs-auart: count FIFO overrun errors
serial: 8250_dw: Add support for IrDA SIR mode
serial: 8250: Expose set_ldisc function
serial: 8250: Add IrDA to UART capabilities
serial: 8250_dma: power off device after TX is done
serial: 8250_port: export serial8250_rpm_{get|put}_tx()
serial: sunsu: Free memory when probe fails
serial: sunhv: Free memory when remove() is called
vt: fix Scroll Lock LED trigger name
tty: typo in comments in drivers/tty/vt/keyboard.c
tty: amba-pl011: Add earlycon support for SBSA UART
tty: nozomi: use permission-specific DEVICE_ATTR variants
tty: serial: Make the STM32 serial port depend on it's arch
serial: ifx6x60: Free memory when probe fails
serial: ioc4_serial: Free memory when kzalloc fails during probe
...
Guenter Roeck (1):
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
Paul Bolle (1):
cris: No need to append -O2 and $(LINUXINCLUDE)
Paul Gortmaker (1):
tty: serial: make crisv10 explicitly non-modular
arch/cris/boot/compressed/Makefile | 3 ---
arch/cris/boot/rescue/Makefile | 9 +++++++--
drivers/tty/serial/crisv10.c | 6 ++----
3 files changed, 9 insertions(+), 9 deletions(-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlhJbl0ACgkQ31LbvUHyf1cK3QCfTFKWF21o02/H8ZFby6oa7Jgp
X4kAn0+rFwV0CtJ3JQum49DsHZf/M72+
=iH+I
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Three patches for minor issues"
* tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: No need to append -O2 and $(LINUXINCLUDE)
tty: serial: make crisv10 explicitly non-modular
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
Fix the following Calltrace:
[ 77.768221] WARNING: CPU: 5 PID: 645 at drivers/dma/dmaengine.c:1069 dma_async_device_unregister+0xe2/0xf0
[ 77.775058] dma_async_device_unregister called while 1 clients hold a reference
[ 77.825048] CPU: 5 PID: 645 Comm: sh Not tainted 4.8.8-WR9.0.0.0_standard+ #3
[ 77.832550] Hardware name: Intel Corp. Aspen Cove/Server, BIOS HAVLCRB1.X64.0012.D58.1604140405 04/14/2016
[ 77.840396] 0000000000000000 ffffc90008adbc80 ffffffff81403456 ffffc90008adbcd0
[ 77.848245] 0000000000000000 ffffc90008adbcc0 ffffffff8105e2e1 0000042d08adbf20
[ 77.855934] ffff88046a861c18 ffff88046a85c420 ffffffff820d4200 ffff88046ae92318
[ 77.863601] Call Trace:
[ 77.871113] [<ffffffff81403456>] dump_stack+0x4f/0x69
[ 77.878655] [<ffffffff8105e2e1>] __warn+0xd1/0xf0
[ 77.886102] [<ffffffff8105e34f>] warn_slowpath_fmt+0x4f/0x60
[ 77.893508] [<ffffffff814187a9>] ? find_next_bit+0x19/0x20
[ 77.900730] [<ffffffff814bf83e>] ? dma_channel_rebalance+0x23e/0x270
[ 77.907814] [<ffffffff814bfee2>] dma_async_device_unregister+0xe2/0xf0
[ 77.914992] [<ffffffff814c53aa>] hsu_dma_remove+0x1a/0x60
[ 77.921977] [<ffffffff814ee14c>] dnv_exit+0x1c/0x20
[ 77.928752] [<ffffffff814edff6>] mid8250_remove+0x26/0x40
[ 77.935607] [<ffffffff8144f1b9>] pci_device_remove+0x39/0xc0
[ 77.942292] [<ffffffff8160cfea>] __device_release_driver+0x9a/0x140
[ 77.948836] [<ffffffff8160d0b3>] device_release_driver+0x23/0x30
[ 77.955364] [<ffffffff81447dcc>] pci_stop_bus_device+0x8c/0xa0
[ 77.961769] [<ffffffff81447f0a>] pci_stop_and_remove_bus_device_locked+0x1a/0x30
[ 77.968113] [<ffffffff81450d4e>] remove_store+0x5e/0x70
[ 77.974267] [<ffffffff81607ed8>] dev_attr_store+0x18/0x30
[ 77.980243] [<ffffffff8123006a>] sysfs_kf_write+0x3a/0x50
[ 77.986180] [<ffffffff8122f5ab>] kernfs_fop_write+0x10b/0x190
[ 77.992118] [<ffffffff811bf1c8>] __vfs_write+0x18/0x40
[ 77.998032] [<ffffffff811bfdee>] vfs_write+0xae/0x190
[ 78.003747] [<ffffffff811c1016>] SyS_write+0x46/0xb0
[ 78.009234] [<ffffffff81a4c31b>] entry_SYSCALL_64_fastpath+0x13/0x8f
[ 78.014809] ---[ end trace 0c36dd73b7408eb2 ]---
This happens when the 8250 serial controller is hotplugged as follows:
echo 1 > /sys/bus/pci/devices/0000:00:1a.0/remove
This trace happens due to the serial port still holding a reference when
the dma device is unregistered.
The dma unregister routine will check if there is still a reference exist,
if so it will give the WARNING(here serial port still was not unregister).
To fix this, We need to unregister the serial port first, then do DMA
device unregister to make sure there is no reference when to DMA routine.
Signed-off-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When running certain workload on a debug kernel with lockdep turned on,
a ppc64 kvm guest could sometimes hit the following lockdep warning:
[ INFO: possible circular locking dependency detected ]
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&mm->mmap_sem);
lock(console_lock);
lock(&mm->mmap_sem);
lock(cpu_hotplug.lock);
*** DEADLOCK ***
Looking at the console code, the console_lock-->mmap_sem scenario will
only happen when reading or writing the console unicode map leading to
a page fault.
To break this circular locking dependency, all the userspace I/O
operations in consolemap.c are now moved outside of the console_lock
critical sections so that the mmap_sem won't be acquired when holding
the console_lock.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing with a gcc-7 snapshot produced an internal compiler error
for this file:
drivers/tty/nozomi.c: In function 'receive_flow_control':
drivers/tty/nozomi.c:919:12: internal compiler error: in get_substring_ranges_for_loc, at input.c:1388
static int receive_flow_control(struct nozomi *dc)
I've reported this at https://gcc.gnu.org/bugzilla/show_bug.cgi?id=78569
but also noticed that the code line contains a stack overflow, as it prints
a string into a slightly shorter fixed-length 'tmp' variable.
A lot of the code here is unnecessary and can be expressed in a simpler
way, relying on the fact that removing the 'DEBUG' macro will also get
rid of all pr_debug() calls. This change should not change any of the
output but avoids both the stack overflow and the gcc crash.
The stack overflow will not happen unless a module load parameter is
also set to enable the debug messages.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check port for NULL in uart_port_deref() since we call it
only when port is defined.
There are few places that violate this. Fix them here as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs-auart driver does not count FIFO overrun errors. These errors never
appear in /proc/tty/driver/ttyAPP. This is because the OERR status bit is
masked by read_status_mask in the rx interrupt function, but the
AUART_STAT_OERR bit is never set in read_status_mask. The patch enables the
counting of overrun errors.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When any 8250 based driver sets up DMA and has UART_CAP_RPM capability enabled
the device is left powered on after transfer is done. We need to schedule a
device suspend operation when DMA completes the transfer.
The patch is based on the work done by the reporter.
Reported-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following fix of runtime PM use in DMA mode requires at least
serial8250_rpm_put_tx() to be available. Export both calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When su_probe() fails it doesn't free *up and we may have a memory
leak. Fix this by freeing *up before return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In each call to hv_remove(), con_read_page and con_write_page is not
getting freed and lead to memory leakage. Fix this by freeing both
pointers in hv_remove().
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a disagreement between drivers/tty/vt/keyboard.c and
drivers/input/input-leds.c with regard to what is a Scroll Lock LED
trigger name: input calls it "kbd-scrolllock", but vt calls it
"kbd-scrollock" (two l's).
This prevents Scroll Lock LED trigger from binding to this LED by default.
Since it is a scroLL Lock LED, this interface was introduced only about a
year ago and in an Internet search people seem to reference this trigger
only to set it to this LED let's simply rename it to "kbd-scrolllock".
Also, it looks like this was supposed to be changed before this code was
merged: https://lkml.org/lkml/2015/6/9/697 but it was done only on
the input side.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable <stable@vger.kernel.org> # 4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare an OF early console for SBSA UART so that the early console device
can be specified via the "stdout-path" property in device-tree.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEVICE_ATTR_RO for read only attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@ro@
declarer name DEVICE_ATTR;
identifier x,x_show;
@@
DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
@script:ocaml@
x << ro.x;
x_show << ro.x_show;
@@
if not (x^"_show" = x_show) then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RO;
identifier ro.x,ro.x_show;
@@
- DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
+ DEVICE_ATTR_RO(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The STM32 serial port is SoC specific so no point enabling it
without the architecture enabled.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When spi_setup() fails it doesn't free ifx_dev and we have a memory
leak. Fix this by freeing ifx_dev before the return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inside ioc4_attach_local() 4 memory was allocated using kzalloc and
assign it to ports[] within loop. When kzalloc fails inside loop,
it returns error without freeing previously allocated memory and we
may have memory leak. Fix this by freeing ports[] before return.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fresh new serial driver for pxa produces warnings when
CONFIG_PM_SLEEP is disabled:
drivers/tty/serial/8250/8250_pxa.c:50:12: error: 'serial_pxa_resume' defined but not used [-Werror=unused-function]
drivers/tty/serial/8250/8250_pxa.c:41:12: error: 'serial_pxa_suspend' defined but not used [-Werror=unused-function]
This removes the #ifdef around the two functions and instead marks both
as __maybe_unused, which is more robust and avoids the warning.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An otherwise very nice cleanup of the pxa2xx uart support marked the
init function of this driver as __deprecated:
drivers/tty/serial/pxa.c:944:1: error: 'serial_pxa_init' is deprecated [-Werror=deprecated-declarations]
This seems unhelpful to me, as we now warn for every allmodconfig build,
which is otherwise free of warnings on most architectures. Let's
remove the annotation again.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop invalid user-pointer check from TIOCGSERIAL handler.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Cc: Mikael Starvik <starvik@axis.com>
Cc: linux-cris-kernel@axis.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop invalid user-pointer checks from custom ioctl handlers.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop invalid user-pointer check from TIOCGSERIAL handler.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
below patch to fix Fourth port offset of Percom PI7C9X7954 boards.
I had a problem using Fourth port on a pci express serial board based on Pericom
PI7C9X7954. Reading datasheet I notice a "special" offset assign to this port
when used in I/O mode.
Offset 0x0 -> UART 0
Offset 0x8 -> UART 1
Offset 0x10 -> UART 2
Offset 0x38 -> UART 3 <<---- This don't follow a logical sequence
This patch add a different init to last port, to have right offset.
I check also Pericom 7952 and 7958 but that devices follow logical sequence,
so they are ok.
Regards,
Angelo
Signed-off-by: Angelo Butti <buttiangelo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While spin is already locked, serial output request causes the deadlock,
because serial output process also tries to lock the spin.
This patch removes serial output with spin locked.
Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
arch/cris/arch-v10/drivers/Kconfig:config ETRAX_SERIAL
arch/cris/arch-v10/drivers/Kconfig: bool "Serial-port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added pxa glue driver for 8250 supports console output, but
fails to build if the 8250 console is disabled:
drivers/tty/serial/8250/8250_pxa.o: In function `early_serial_pxa_setup':
8250_pxa.c:(.init.text+0x50): undefined reference to `early_serial8250_setup'
This adds an #ifdef like the other glue drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware book says, the FCR is combined with a register called
CHAR (it will trigger interrupt when a specific character is
received). At first, I used lock/read/modify/write/unlock dance for
the FCR to not affect the upper bits, but the CHAR is actually never
used. It should not hurt to always clear the CHAR and to handle the
FCR as a normal case. It can save the costly locking.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For this driver, uart_port::regshift is always 2. Hardcode the
shift value instead of reading ->regshift to get an already known
value. (pointed out by Denys Vlasenko)
Furthermore, I am using register macros that are already shifted,
which will save code a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
arch/cris/arch-v10/drivers/Kconfig:config ETRAX_SERIAL
arch/cris/arch-v10/drivers/Kconfig: bool "Serial-port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->console flag is always false, as uart_console() is called
before the serial console has been registered.
Hence for a serial port used as the console, uart_tty_port_shutdown()
will still be called when userspace closes the port, powering it down.
This may lead to a system lock up when the serial console driver writes
to the serial port's registers.
To fix this, move the setting of port->console after the call to
uart_configure_port(), which registers the serial console.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[robh: rebased on tty-linus]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc83 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable)
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a41bc2a2b ("tty: serial: fsl_lpuart: add polled console
functions") caused a build warning about an unused variable, so fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Nicolae Rosia <nicolae_rosia@mentor.com>
Cc: Stefan Golinschi <stefan.golinschi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When resizing a vt its selection may exceed the new size, resulting in
an invalid memory access [1]. Clear the selection before resizing.
[1] http://lkml.kernel.org/r/CACT4Y+acDTwy4umEvf5ROBGiRJNrxHN4Cn5szCXE5Jw-d1B=Xw@mail.gmail.com
Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_update first reads the IOState register and then triggers
a write if needed. However, GPIOS might be configured as an input so
the read to IOState on this GPIO is the current state which might
be random.
Signed-off-by: Francois Berder <Francois.Berder@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NXP SC16C2552 requires that we always write a reset to the RX FIFO and
TX FIFO whenever we enable the FIFOs
Cc: xe-kernel@external.cisco.com
Signed-off-by: Steve Shih <sshih@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Size of kmalloc() in vc_do_resize() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Put a reasonable upper bound on terminal size to prevent WARNINGs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
CC: David Rientjes <rientjes@google.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where head == 0 on the circular buffer, there should be one
DMA buffer, not two. The second zero-length buffer would break the
lpuart driver, transfer would never complete.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes the code understandable at least. No functional changes.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is mirrorred in scrolldelta implementations of both vgacon
and sisusb. Let's move the code to a separate helper where we will
perform a common cleanup and further changes.
While we are moving the code, make it linear and save one indentation
level. This is done by returning from the "!lines" then-branch
immediatelly. This allows flushing the else-branch 1 level to the
left, obviously.
Few more new lines and comments were added too.
And do not forget to export the helper function given sisusb can be
built as module.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both scrup and scrdown are copies of the same code except source and
destination pointers computation. Unify those functions into a single
one named con_scroll.
Note that scrdown used step to compute the destination, while scrup
did the computation explicitly. We sticked to the latter here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scrolling helpers scrup and scrdown both accept 'top' and 'bottom' as
unsigned int. Number of lines 'nr' is accepted as int, but all callers
pass down unsigned too. So change the type of 'nr' to unsigned too.
Now, promote unsigned int from the helpers up to the con_scroll
hook which actually accepted all those as signed int.
Next, the 'dir' parameter can have only two values and we define
constants for that: SM_UP and SM_DOWN. Switch them to enum and do
proper type checking on 'dir' too.
Finally, document the behaviour of the hook.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: <linux-fbdev@vger.kernel.org>
Cc: <linux-usb@vger.kernel.org>
Cc: <linux-parisc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs
likes F81866. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81865 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
Level/Low: IRQ_MODE0:0
Edge/High: IRQ_MODE0:1
The following list is brief descriptions of F81865:
F81865 (0704)
9Bit(not implements with mainline)
RS485(implemented)
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs
likes F81216H. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81866 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
The following list is brief descriptions of F81866:
F81866 (1010)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H
The following list is brief descriptions of F81216 series:
F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)
F81216 (0208)
basically 16550A
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated
as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger
level multiplier as 4x when F81216H detected.
Default 16550A trigger level is 8Bytes. When this patch applied, the
trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX
incoming interrupts.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set IRQ Mode when port probed in probe_setup_port()
It should hold the IO port premission via fintek_8250_enter_key() and
release via fintek_8250_exit_key() when we configure the SuperIO.
This patch will move all SuperIO configure operations to
probe_setup_port() to reduce fintek_8250_enter_key() and
fintek_8250_exit_key() usage.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we need to access SuperIO registers, It should write register offset
to base_addr and read/write value to base_addr + 1 to perform read/write.
We can make it more simply with write/read functions.
This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to
reduce SuperIO register operation with lot of outb()/inb().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transfer the device-tree pxa uart handling from 8250_of to the new
8250_pxa. As a corollary, add the early console definition into
8250_pxa.
This enables to have the same uart node for the early console and the
normal uart.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of a direct assignment use pci_irq_vector() call as it's done for the
other case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of IRQF_ONESHOT when registering an interrupt handler with
request_irq() is non-sensical.
Not only that, it also prevents the handler from being threaded when it
otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the
following deadlock observed by Sean Nyekjaer on -rt:
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[..]
rt_spin_lock_slowlock from queue_kthread_work
queue_kthread_work from sc16is7xx_irq
sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu
handle_irq_event_percpu from handle_irq_event
handle_irq_event from handle_level_irq
handle_level_irq from generic_handle_irq
generic_handle_irq from mxc_gpio_irq_handler
mxc_gpio_irq_handler from mx3_gpio_irq_handler
mx3_gpio_irq_handler from generic_handle_irq
generic_handle_irq from __handle_domain_irq
__handle_domain_irq from gic_handle_irq
gic_handle_irq from __irq_svc
__irq_svc from rt_spin_unlock
rt_spin_unlock from kthread_worker_fn
kthread_worker_fn from kthread
kthread from ret_from_fork
Fixes: 9e6f4ca3e5 ("sc16is7xx: use kthread_worker for tx_work and irq")
Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Cc: linux-rt-users@vger.kernel.org
Cc: Jakub Kicinski <moorray3@wp.pl>
Cc: stable@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable MWI mechanism if PCI bus master supports it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to set PCI bus mastering when device is not doing any DMA.
Though on Intel Quark DMA is a part of UART IP and thus shares same device in
Linux kernel.
Enable bus mastering only for Quark case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_lpuart cannot be used with kgdb because the kgdb
initcall is called before the driver's init.
Move kgdb to be initialized after all serial drivers
have been inited.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Signed-off-by: Stefan Golinschi <stefan.golinschi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds polling functions as used by kgdb.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Signed-off-by: Stefan Golinschi <stefan.golinschi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds function pl011_console_match() that implements
method match of struct console. It allows to match consoles against
data specified in a string, for example taken from command line or
compiled by ACPI SPCR table handler.
This patch was merged to tty-next but then reverted because of
conflict with
commit 46e36683f4 ("serial: earlycon: Extend earlycon command line option to support 64-bit addresses")
Now it is fixed.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4fe0d15488 ("PCI: Use positive flags in pci_alloc_irq_vectors()")
replaces flags from negative to positive values which makes mandatory to have
the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op).
This basically drops MSI enabling in 8250_lpss driver.
Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of
0 to pci_alloc_irq_vectors().
Fixes: 60a9244a5d ("serial: 8250_lpss: enable MSI for Intel Quark")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pxa2xx-uart was a separate uart platform driver. It was declaring
the same device names and numbers as 8250 driver. As a result,
it was impossible to use 8250 driver on PXA SoCs.
Upon closer examination pxa2xx-uart turned out to be a clone of
8250_core driver.
Workaround for Erratum #19 according to Marvel(R) PXA270M Processor
Specification Update (April 19, 2010) is dropped. 8250_core reads
from FIFO immediately after checking DR bit in LSR.
The patch leaves the original SERIAL_PXA driver around. The original
driver is just marked DEPRECATED in Kconfig and C source. When
the original driver is considered safe to remove, no changes
to SERIAL_8250 will be necessary.
Compiling SERIAL_8250_CONSOLE and SERIAL_PXA_CONSOLE even without
SERIAL_8250_PXA breaks console for SERIAL_PXA. For this reasons, the new
and the original drivers are made mutually exclusive.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: James Cameron <quozl@laptop.org>
CC: Robert Jarzmik <robert.jarzmik@free.fr>
CC: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rebased on v4.8]
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 761ed4a945 ('tty: serial_core: convert uart_close to use
tty_port_close') started setting the ttyport console flag for serial
drivers. This is causing crashes, hangs, or garbage output on several
platforms because the serial shutdown is skipped and IRQs are left
enabled.
Partially revert commit 761ed4a945 and drop reporting UART tty_ports
as a console leaving the console handling to the serial_core as it was
before.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reported-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, 'value' is always a byte, then this code is clearing
bit 15, which is already clear. I meant to clear bit 7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `stm32_serial_remove':
stm32-usart.c:(.text+0xcea1a): undefined reference to `bad_dma_ops'
stm32-usart.c:(.text+0xcea7a): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/stm32-usart.c: In function ‘stm32_receive_chars’:
drivers/tty/serial/stm32-usart.c:130: warning: comparison is always true due to limited range of data type
drivers/tty/serial/stm32-usart.c: In function ‘stm32_tx_dma_complete’:
drivers/tty/serial/stm32-usart.c:177: warning: comparison is always false due to limited range of data type
stm32_usart_offsets.icr is u8, while UNDEF_REG = ~0 is int, and thus
0xffffffff.
As all registers in stm32_usart_offsets are u8, change the definition of
UNDEF_REG to 0xff to fix this.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
So remove the bogus division.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Petr Písař <ppisar@redhat.com>
Fixes: f8df13e0a9 (tty: Clean console safely)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- set min/max_mtu in all hdlc drivers, remove hdlc_change_mtu
- sent max_mtu in lec driver, remove lec_change_mtu
- set min/max_mtu in x25_asy driver
CC: netdev@vger.kernel.org
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Kevin Curtis <kevin.curtis@farsite.co.uk>
CC: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge my system logging cleanups, triggered by the broken '\n' patches.
The line continuation handling has been broken basically forever, and
the code to handle the system log records was both confusing and
dubious. And it would do entirely the wrong thing unless you always had
a terminating newline, partly because it couldn't actually see whether a
message was marked KERN_CONT or not (but partly because the LOG_CONT
handling in the recording code was rather confusing too).
This re-introduces a real semantically meaningful KERN_CONT, and fixes
the few places I noticed where it was missing. There are probably more
missing cases, since KERN_CONT hasn't actually had any semantic meaning
for at least four years (other than the checkpatch meaning of "no log
level necessary, this is a continuation line").
This also allows the combination of KERN_CONT and a log level. In that
case the log level will be ignored if the merging with a previous line
is successful, but if a new record is needed, that new record will now
get the right log level.
That also means that you can at least in theory combine KERN_CONT with
the "pr_info()" style helpers, although any use of pr_fmt() prefixing
would make that just result in a mess, of course (the prefix would end
up in the middle of a continuing line).
* printk-cleanups:
printk: make reading the kernel log flush pending lines
printk: re-organize log_output() to be more legible
printk: split out core logging code into helper function
printk: reinstate KERN_CONT for printing continuation lines
Long long ago the kernel log buffer was a buffered stream of bytes, very
much like stdio in user space. It supported log levels by scanning the
stream and noticing the log level markers at the beginning of each line,
but if you wanted to print a partial line in multiple chunks, you just
did multiple printk() calls, and it just automatically worked.
Except when it didn't, and you had very confusing output when different
lines got all mixed up with each other. Then you got fragment lines
mixing with each other, or with non-fragment lines, because it was
traditionally impossible to tell whether a printk() call was a
continuation or not.
To at least help clarify the issue of continuation lines, we added a
KERN_CONT marker back in 2007 to mark continuation lines:
4749252776 ("printk: add KERN_CONT annotation").
That continuation marker was initially an empty string, and didn't
actuall make any semantic difference. But it at least made it possible
to annotate the source code, and have check-patch notice that a printk()
didn't need or want a log level marker, because it was a continuation of
a previous line.
To avoid the ambiguity between a continuation line that had that
KERN_CONT marker, and a printk with no level information at all, we then
in 2009 made KERN_CONT be a real log level marker which meant that we
could now reliably tell the difference between the two cases.
5fd29d6ccb ("printk: clean up handling of log-levels and newlines")
and we could take advantage of that to make sure we didn't mix up
continuation lines with lines that just didn't have any loglevel at all.
Then, in 2012, the kernel log buffer was changed to be a "record" based
log, where each line was a record that has a loglevel and a timestamp.
You can see the beginning of that conversion in commits
e11fea92e1 ("kmsg: export printk records to the /dev/kmsg interface")
7ff9554bb5 ("printk: convert byte-buffer to variable-length record buffer")
with a number of follow-up commits to fix some painful fallout from that
conversion. Over all, it took a couple of months to sort out most of
it. But the upside was that you could have concurrent readers (and
writers) of the kernel log and not have lines with mixed output in them.
And one particular pain-point for the record-based kernel logging was
exactly the fragmentary lines that are generated in smaller chunks. In
order to still log them as one recrod, the continuation lines need to be
attached to the previous record properly.
However the explicit continuation record marker that is actually useful
for this exact case was actually removed in aroundm the same time by commit
61e99ab8e3 ("printk: remove the now unnecessary "C" annotation for KERN_CONT")
due to the incorrect belief that KERN_CONT wasn't meaningful. The
ambiguity between "is this a continuation line" or "is this a plain
printk with no log level information" was reintroduced, and in fact
became an even bigger pain point because there was now the whole
record-level merging of kernel messages going on.
This patch reinstates the KERN_CONT as a real non-empty string marker,
so that the ambiguity is fixed once again.
But it's not a plain revert of that original removal: in the four years
since we made KERN_CONT an empty string again, not only has the format
of the log level markers changed, we've also had some usage changes in
this area.
For example, some ACPI code seems to use KERN_CONT _together_ with a log
level, and now uses both the KERN_CONT marker and (for example) a
KERN_INFO marker to show that it's an informational continuation of a
line.
Which is actually not a bad idea - if the continuation line cannot be
attached to its predecessor, without the log level information we don't
know what log level to assign to it (and we traditionally just assigned
it the default loglevel). So having both a log level and the KERN_CONT
marker is not necessarily a bad idea, but it does mean that we need to
actually iterate over potentially multiple markers, rather than just a
single one.
Also, since KERN_CONT was still conceptually needed, and encouraged, but
didn't actually _do_ anything, we've also had the reverse problem:
rather than having too many annotations it has too few, and there is bit
rot with code that no longer marks the continuation lines with the
KERN_CONT marker.
So this patch not only re-instates the non-empty KERN_CONT marker, it
also fixes up the cases of bit-rot I noticed in my own logs.
There are probably other cases where KERN_CONT will be needed to be
added, either because it is new code that never dealt with the need for
KERN_CONT, or old code that has bitrotted without anybody noticing.
That said, we should strive to avoid the need for KERN_CONT. It does
result in real problems for logging, and should generally not be seen as
a good feature. If we some day can get rid of the feature entirely,
because nobody does any fragmented printk calls, that would be lovely.
But until that point, let's at mark the code that relies on the hacky
multi-fragment kernel printk's. Not only does it avoid the ambiguity,
it also annotates code as "maybe this would be good to fix some day".
(That said, particularly during single-threaded bootup, the downsides of
KERN_CONT are very limited. Things get much hairier when you have
multiple threads going on and user level reading and writing logs too).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
This reverts commit 8b8f347d3a as it
causes build errors in linux-next
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds function pl011_console_match() that implements
method match of struct console. It allows to match consoles against
data specified in a string, for example taken from command line or
compiled by ACPI SPCR table handler.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ARM Server Base Boot Requiremets' [1] mentions SPCR (Serial Port
Console Redirection Table) [2] as a mandatory ACPI table that
specifies the configuration of serial console.
Defer initialization of DT earlycon until ACPI/DT decision is made.
Parse the ACPI SPCR table, setup earlycon if required,
enable specified console.
Thanks to Peter Hurley for explaining how this should work.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0044a/index.html
[2] https://msdn.microsoft.com/en-us/library/windows/hardware/dn639132(v=vs.85).aspx
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have multiple "earlycon" early_param handlers - merge the DT one into
the main earlycon one. It's a cleanup that also will be useful
to defer setting up DT console until ACPI/DT decision is made.
Rename the exported function to avoid clashing with the function from
arch/microblaze/kernel/prom.c
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9f12cea96f.
Mark writes:
Unfortunately, this patch will result in erroneous stack traces
on some architectures. Sorry about this; I should have verified
this more thoroughly before sending the series out.
Please drop the patch at your earliest convenience.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain on -EPROBE_DEFER when attempting to get the irq.
the driver probe will be retried later.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit:
81539169f2 ("x86/dumpstack: Remove NULL task pointer convention")
... having a NULL task parameter imply current leads to subtle bugs in stack
walking code (so far seen on both 86 and arm64), makes callsites harder to
read, and is unnecessary as all callers have access to current.
As a step towards removing the problematic NULL-implies-current idiom entirely,
have the sysrq code explicitly pass current to show_stack.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USR2_DCDIN bit is tested for in register usr1. As the name
suggests the usr2 register should be used instead. This fixes
reading the Carrier detect status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: 90ebc48386 ("serial: imx: repair and complete handshaking")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: <stable@vger.kernel.org> # 4.5+
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 2 warnings when building kernel with W=1:
drivers/tty/serial/stm32-usart.c:63:5: warning: no previous prototype for 'stm32_pending_rx' [-Wmissing-prototypes]
drivers/tty/serial/stm32-usart.c:88:15: warning: no previous prototype for 'stm32_get_char' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initialisation of control register and baud rate to
cdns_early_console_setup(), required when running kernel standalone
without a boot loader. Baud rate is only initialised when specified in
earlycon command-line option, otherwise it is assumed this has been
set by a boot loader. Updated Documentation/kernel-parameters.txt
accordingly.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Remove the unwated checks while reading the parity,framing,
overrun and Break detection errors.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
b1cf74970df5470ffbc8e7876a9edf5e3498ef94]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing interrupt handling logic has following issues.
- Upon a parity error with default configuration, the control
never comes out of the ISR thereby hanging Linux.
- The error handling logic around framing and parity error are buggy.
There are chances that the errors will never be captured.
This patch ensures that the status registers are cleared on all cases so
that a hang situation never arises.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
ac297e20d399850d7a8e373b6eccf2e183c15165 with manual conflict resolution]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building this driver with a 64-bit dma_addr_t type results in
a compiler warning:
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_rx_probe':
drivers/tty/serial/stm32-usart.c:746:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_tx_probe':
drivers/tty/serial/stm32-usart.c:818:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
While the type conversion here is harmless, this hints at a different
problem: we pass an __iomem pointer into a DMA engine, which expects
a phys_addr_t. This happens to work because stm32 has no MMU and
ioremap() is an identity mapping here, but it's still an incorrect
API use. Using dma_addr_t is doubly wrong here, because that would
be the result of dma_map_single() rather than the physical address.
Using the mapbase instead fixes multiple issues:
- the warning is gone
- we don't go through ioremap in error
- the cast is gone, making it use the correct resource_size_t/phys_addr_t
type in the process.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem with previous code was it rounded values in wrong
place and produced wrong baud rate in some cases.
Signed-off-by: Alexey Starikovskiy <aystarik@gmail.com>
[nicolas.ferre@atmel.com: port to newer kernel and add commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch makes changes not to enable parity error interrupt.
With the current implementation, each parity error results in
two distinct interrupts (almost always). The first one is normal
parity error interrupt with no data in the fifo and the second one
is a proper Rx interrupt with the received data in the fifo. By
disabling parity error interrupt we still ensure handling of
parity errors as for the Rx fifo interrupt the parity error still
shows up in the interrupt status register. Considering the fact
that the by default INPCK and IGNPAR are not set, this is the
optimal implementation for parity error handling.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[stelford@cadence.com: cherry picked from
https://github.com/Xilinx/linux-xlnx commit
bf9f610b445e2c9ed33c41e1e0e30b43be4e1f97 with manual conflict
resolution]
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds dma mode support for rx and tx
with pio mode as fallback in case of dma error.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the clock enabled at the end of stm32_init_port
but disable it in stm32_serial_remove.
Note that stm32_pm function is there to manage the
clock at runtime.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"st,hw-flow-ctrl" property is documented in device tree
binding whereas "auto-flow-control" was used in the code.
The driver is now aligned with the binding name
"st,hw-flow-ctrl".
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register offset management rework to support both
stm32f4 (default) and stm32f7. Driver rework to
ensure same functional level on both stm32f4 and
stm32f7: no new feature in this version yet.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After issuing the reset, driver is not checking the rx and tx reset
done status. So, modified driver to wait for the reset done status.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds RXBS register access support for zynqmp.
To avoid the corner error conditions it will consider only
RXBS[2:0] bits while checking the error conditions
(Parity,Framing and BRAK).
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Less magic that only requires comments.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0e125a5fac ("tty: amba-pl011: define flag register bits for ZTE
device") changes earlycon function pl011_putc() to use a pointer to
uart_amba_port. This causes a regression when earlycon is enabled,
because uart_amba_port is not available yet at earlycon time. Let's
revert the change on pl011_putc() to fix the regression.
The earlycon support for ZTE device can probably be added later by
declaring a new earlycon setup function with a vendor specific
compatible.
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 0e125a5fac ("tty: amba-pl011: define flag register bits for ZTE device")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now, these fall back to regular (dark) colors.
It'd be tempting to replace blink with bright backgrounds, as permitted by
CGA/VGA -- we already muck with the other programmable bit (foreground
brightness vs 512 character font). This would bring vgacon in line with
fbcon, which doesn't support blink anywhere but on some drivers renders
that bit as bright background. If that is done, this commit should be
amended to be one of ways of setting that bit.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These codes are supported by all major terminals, thus they occasionally see
some use despite being redundant with \e[38;5;(x+8)m or (less exactly)
\e[1;3(x)m.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some guy went on a patching spree, adding 24-bit colour support all around:
https://gist.github.com/XVilka/8346728
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All other uses of vc_npar are inclusive (save for < NPAR) which raises
eyebrows, so let's at least do so consistently.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it show up on UBSAN:
perl -e 'for (0..15) {my @x=("0")x$_;push @x,qw(38 2 64 128 192 4);printf
"\e[%smAfter %d zeroes.\e[0m\n", join(";",@x[0..($_+5<15?$_+5:15)]), $_}'
Seems harmless: if you can programmatically read attributes of a vt
character (/dev/vcsa*), multiple probes can obtain parts of vt_mode then
lowest byte (5th on 64-bit big-endian) of a pointer.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that workqueue can handle work item queueing from very early
during boot, there is no need to delay schedule_work() while
!keventd_up(). Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
The ptmx_fops structure is only changed during init, so mark it as such.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dmaengine_terminate_all() is deprecated and should be replaced by
dmaengine_terminate_sync() in non-atomic context or dmaengine_terminate_async()
with dmaengine_synchronize().
See commit b36f09c3c4 ("dmaengine: Add transfer termination synchronization support")
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 761ed4a945 ("tty: serial_core: convert uart_close to use
tty_port_close") refactored uart_close() to use tty_port_close(). At the same
time it introduced a potential NULL pointer dereference. Rearrange the code to
avoid kernel crash.
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), interrupts from GPIOs are not disabled any more
when the serial port is closed, leading to an oops when the one of the
input pin is toggled (CTS/DSR/DCD/RNG).
This is only the case if those pins are used as GPIOs, i.e. declared
like that:
usart1: serial@f8020000 {
/* CTS and DTS will be handled by GPIO */
status = "okay";
rts-gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
cts-gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
dtr-gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
dsr-gpios = <&pioC 31 GPIO_ACTIVE_LOW>;
rng-gpios = <&pioB 12 GPIO_ACTIVE_LOW>;
dcd-gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
};
That's because modem interrupts used to be freed in atmel_shutdown().
After commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), this code was just removed.
Calling atmel_disable_ms() disables the interrupts and everything works
fine again.
Tested on at91sam9g35-cm
(This patch doesn't apply on -stable kernels, fixes for 4.4 and 4.7 will
be sent after this one is applied.)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 18dfef9c7f ("serial: atmel: convert to irq handling provided mctrl-gpio")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function lpuart_start_rx_dma() is called from several
places, in some of which, such as lpuart_startup(), a lock
be held here, so we should use GFP_ATOMIC when a lock is held.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dev.of_node is not NULL, we also need to set IRQF_TRIGGER_FALLING
flag, otherwise it may cause uncertain interrupts.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck reported a regression caused by commit "serial: earlycon:
Extend earlycon command line option to support 64-bit addresses":
console= and earlycon= options have the following format:
...,<addr>,<options>
Historically used here simple_strtoul() had no problems with comma, but the
new and recommended kstrtoull() requires null-terminated string and returns
-EINVAL in case there are "options" at the end. There is no recommended to
use function currently that will support it, so stick to obsolete
simple_strtoull() variant.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions called by serial_imx_probe emit an error message themself
(like kmalloc() and friends). clk_prepare_enable() and
devm_request_irq() however don't which might make the driver silently
fail to probe. So add an error message for these.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon implementation used "unsigned long" internally, but there are systems
(ARM with LPAE) where sizeof(unsigned long) == 4 and uart is mapped beyond 4GiB
address range.
Switch to resource_size_t internally and replace obsoleted simple_strtoul() with
kstrtoull().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 1 warning when building kernel with W=1:
drivers/tty/serial/earlycon-arm-semihost.c:56:12: warning: no previous prototype for 'early_smh_setup' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the check of em485 variable to be either (em485) or (!em485) instead of
the explicit comparison to NULL.
While here, remove redundant check in __do_stop_tx_rs485() and
__stop_tx_rs485() since the functions ain't called with NULL value of em485
variable.
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d58 ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART DMA was only being configured on i.MX6Q compatible devices. We
know that the DMA also works for i.MX53 devices, so enable uart DMA for
imx53 and let the device tree to configure if DMA should be used or not.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use an unified new dev variable instead of &pdev->dev and p->dev
in probe function.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The APM X-Gene SoC UART is the only board that still needs
the hard-coded values, so handle it separately in
dw8250_quirks(). The other ACPI platforms are able to
provide the values with device properties.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update error counters when DMA is used for receiving data. Do
this by using DMA transaction error event instead error interrupts
to reduce interrupt load.
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IMX UART has a 32 bytes HW buffer which can be filled up in
2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53).
Taking this in consideration there is a good probability to lose
data because of the DMA startup latency.
Our tests (explained below) indicates a latency up to 4400us when
creating interrupt load and ~70us without. When creating interrupt
load I was able to see continuous overrun errors by checking serial
driver statistics using the command:
`cat /proc/tty/driver/IMX-uart`.
Replace manual restart of DMA with cyclic DMA to eliminate data loss
due to DMA engine startup latency (similar approch to atmel_serial.c
driver). As result the DMA engine will start on the first serial data
transfer and stops only when serial port is closed.
Tests environment:
Using the m53evk board I have used a GPIO for profiling the IMX
serial driver.
- The RX line and GPIO were connected to oscilloscope.
- Run a small test program on the m53evk board that will only open
and read data from ttymxc2 port.
- Connect the ttymxc2 port to my laptop using a USB serial converter
where another test program is running, able to send configurable
packet lengths and intervals.
- Serial ports configured at 115200 8N1.
- Interrupts load created by disconnecting/connecting (3s interval)
a USB hub, using a digital switch, with 4 USB devices (USB-Serial
converter, USB SD card, etc) connected.
(around 160 interrupts/second generated)
- The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM
events are received and toggled back, once the DMA configuration
is finalized, at the end of `imx_dma_rxint`.
Measurements:
The measurements were done from the end of the last byte (RX line) until
the GPIO was toggled back LOW.
Note: The GPIO toggling was done using `gpiod_set_value` method.
Tests performed:
1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets
will activate the RRDY threshold event and IMX serial interrupt
called.
Results:
- DMA start latency (interrupt start latency +
DMA configuration) consistently 70us when system not loaded.
- DMA start latency up to 4400us when system loaded.
2. Sending 40 bytes packet at 8mS interval.
Results with load:
- Able to observe overruns by running:
`watch -n1 cat /proc/tty/driver/IMX-uart`
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.
The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
is in use
Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.
The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.
The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.
Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.
While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously sc16is7xx_power was called in order to set the device to a
low power mode.
However since SC16IS7XX_EFR_ENABLE_BIT was not set beforehand this
suspend request had not effect.
Also, soft-reset the device prior to port initialization. It may
otherwise be in a state (interrupt pending, fifo not empty) which
prevents it from sleeping.
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mediatek can support baud rate up to 4M.
the 'uart_get_baud_rate' function will limit the max baud rate.
Modify max baud to remove the limit.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit c1a67b48f6 ("serial: 8250_pci: replace switch-case by
formula for Intel MID"), the 8250 driver crashes in the byt_set_termios()
function with a divide error. This is caused by the fact that a baud rate of 0
(B0) is not handled properly. Fix it by falling back to B9600 in this case.
Reported-by: "Mendez Salinas, Fernando" <fernando.mendez.salinas@intel.com>
Fixes: c1a67b48f6 ("serial: 8250_pci: replace switch-case by formula for Intel MID")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Vybrid's build-in support for RS-485 auto RTS for controlling line
direction of RS-485 transceiver driver.
Enable RS485 feature by either using ioctrl 'TIOCSRS485' or enable it in the
device tree by setting 'linux,rs485-enabled-at-boot-time' property.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA mode is enabled one need to make sure the DMA channels are idle before
entering suspend mode especially when UART ports which are set as wakeup source
and console port with no_console_suspend is set. This patch takes care of
gracefully releasing DMA channels for the above two cases and start the DMA at
resume.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop PIO to DMA switching and use scatter/gather DMA for Tx path to improve
performance.
Some part of the code is borrowed from imx serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial approach of DMA implementatin for RX is inefficient due to switching
from PIO to DMA, this leads to overruns especially on instances with the smaller
FIFO. To address these issues this patch uses a cyclic DMA for receiver path.
Some part of the code is borrowed from atmel serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default the driver always configure the mode as 8s1 even when 8m1 mode is
selected. Fix this by adding support to control the space/mark bit.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e4934c6d6 ("tty: serial: fsl_lpuart: clear receive flag on FIFO
flush") implemented clearing of the receive flag by reading the status register
only. It turned out that even though we flush the FIFO afterwards, a explicit
read of the data register is still required.
This leads to a FIFO underrun. To avoid this, follow the advice in the overrun
"Operation section": Unconditionally clear RXUF after using RXFLUSH.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the tx_empty callback only considers the Transmit Complete Flag (TC).
The reference manual is not quite clear if the TC flag covers the TX FIFO too.
Debug prints on real hardware have shown that from time to time the TC flag is
asserted (indicating Transmitter idle) while there are still data in the
TX FIFO. Hence, in this case the serial core will call the shutdown callback
even though there are data remaining in the TX FIFO buffers.
Avoid early shutdowns by considering the TX FIFO empty flag too. Also avoid
theoretical race conditions between DMA and the driver by checking whether the
TX DMA is in progress too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS based Boston platform provides a 25MHz clock to the UART.
Enable the driver for MIPS and add support in the driver to read
the frequency from device tree.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should check the data->pclk, not data->clk when get apb_pclk.
Fixes: c8ed99d4f6a8("serial: 8250_dw: Add support for deferred probing")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2nd parameter of 'find_first_zero_bit' is the number of bits to search.
In this case, we are passing 'sizeof(vt8500_ports_in_use)'.
'vt8500_ports_in_use' is an 'unsigned long'. So the sizeof is likely to
return 4 on a 32 bits kernel.
A few lines below, we check if it is below VT8500_MAX_PORTS, which is 6.
It is likely that the number of bits in a long was expected here.
In order to fix it:
- use DECLARE_BITMAP when declaring the vt8500_ports_in_use
- use VT8500_MAX_PORTS as a maximum value when checking/setting bits in
this bitmap
- modify code now that 'vt8500_ports_in_use' has become a pointer
because of the use of DECLARE_BITMAP
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_close handles much of the common parts of tty close. Convert
uart_close to use it and move the serial_core specific parts into
tty_port.shutdown function. This will be needed to use tty_port functions
directly from in kernel clients.
This change causes ops->stop_rx() to be called after uart_wait_until_sent()
is called which I think should be fine. Otherwise, the sequence of the
close should be the same.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_open handles much of the common parts of tty opening. Convert
uart_open to use it and move the serial_core specific parts into
tty_port.activate function. This will be needed to use tty_port functions
directly from in kernel clients.
The tricky part is uart_port_startup can return positive values to allow
setserial to configure the port. We now return the positive value to
tty_port_open so that the tty is not marked as initialized and then set the
return value in uart_open to 0.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Samsung serial driver registered for CPU frequency transitions to
recalculate its clock when ARM clock frequency changes. This is needed
only on S3C24xx platform so limit the ifdef to respective cpufreq
driver.
On S3C24xx the ratio ratio between frequencies of UART's parent clock
(pclk) and ARM's parent clock (fclk) remains fixed. Therefore when ARM
clock frequency goes down, the serial is also affected.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USART device provides a fractional baud rate generator to get a more
accurate baud rate. It can be used only when the USART is configured in
'normal mode' and this feature is not available on AT91RM9200 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d3287 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d3287.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no Peripheral Identification Registers on ZTE PL011 device, so
although the driver amba-pl011 is ready to work for ZTE device, the
device cannot be probed by the driver at all.
With arm,primecell-periphid DT bindings (bindings/arm/primecell.txt) in
place, it should be the cleanest the way to use a pseudo-ID to probe the
device from AMBA bus. We create an unofficial vendor number
AMBA_VENDOR_LINUX, which will practically never become an official
vendor ID, and takes Configuration, Revision number, and Part number as
input to compose a pseudo-ID for ZTE device.
Also, since we start using vendor_zte to probe ZTE device, the
__maybe_unused for vendor_zte is removed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE PL011 device has a fixed FIFO size 16. Let's add a .get_fifosize
hook for it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason we do not really understand, ZTE hardware designers
choose to define PL011 Flag Register bit positions differently from
standard ones as below.
Bit Standard ZTE
-----------------------------------
CTS 0 1
DSR 1 3
BUSY 3 8
RI 8 0
Let's define these bits into vendor data and get ZTE PL011 supported
properly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the fintek driver required defining some macros, but
one of them clashes with a system header on ARM:
drivers/tty/serial/8250/8250_fintek.c:34:0: error: "IRQ_MODE" redefined [-Werror]
#define IRQ_MODE 0x70
In file included from /git/arm-soc/arch/arm/include/asm/ptrace.h:13:0,
from /git/arm-soc/arch/arm/include/asm/irqflags.h:6,
from /git/arm-soc/include/linux/irqflags.h:15,
from /git/arm-soc/arch/arm/include/asm/bitops.h:27,
from /git/arm-soc/include/linux/bitops.h:36,
from /git/arm-soc/include/linux/kernel.h:10,
from /git/arm-soc/include/linux/list.h:8,
from /git/arm-soc/include/linux/module.h:9,
from /git/arm-soc/drivers/tty/serial/8250/8250_fintek.c:11:
arch/arm/include/uapi/asm/ptrace.h:55:0: note: this is the location of the previous definition
This renames the newly introduced 'IRQ_MODE' macro to FINTEK_IRQ_MODE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4da22f1418 ("serial: 8250_fintek: fix the mismatched IRQ mode")
Link: https://patchwork.kernel.org/patch/9200119/
Acked-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
We accidentally take the "port->lock" twice in a row. This old code
was supposed to be deleted.
Fixes: e58e241c17 ('sparc: serial: Clean up the locking for -rt')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the hvc driver to use the OPAL irqchip if made available by the
running firmware. If it is not present, the driver falls back to the
existing OPAL event number.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2def86a720 ("hvc: Convert to using interrupts instead of opal
events") enabled the use of interrupts in the hvc_driver for OPAL
platforms. However on machines with more than one hvc console, any
console after the first will fail to register an interrupt handler in
notifier_add_irq() since all consoles share the same IRQ number but do
not set the IRQF_SHARED flag:
genirq: Flags mismatch irq 31. 00000000 (hvc_console) vs. 00000000 (hvc_console)
hvc_open: request_irq failed with rc -16.
This error propagates up to hvc_open() and the console is closed, but
OPAL will still generate interrupts that are not handled, leading to
rcu_sched stall warnings.
Set IRQF_SHARED when calling request_irq(), allowing additional consoles
to start properly. This is only set for consoles handled by
hvc_opal_probe(), leaving other types unaffected.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's a part of oom context just like allocation order and nodemask, so
let's move it to oom_control instead of passing it in the argument list.
Link: http://lkml.kernel.org/r/40e03fd7aaf1f55c75d787128d6d17c5a71226c2.1464358556.git.vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Here is the big tty and serial driver update for 4.8-rc1.
Lots of good cleanups from Jiri on a number of vt and other tty related
things, and the normal driver updates. Full details are in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPbQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspWXgAn046
QCMeFya4J1zjYjcGXJzNfGMUAKCHxha8Xe65cc0LDz8mNB0MgzjHEg==
=ED8v
-----END PGP SIGNATURE-----
Merge tag 'tty-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.8-rc1.
Lots of good cleanups from Jiri on a number of vt and other tty
related things, and the normal driver updates. Full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
tty/serial: atmel: enforce tasklet init and termination sequences
serial: sh-sci: Stop transfers in sci_shutdown()
serial: 8250_ingenic: drop #if conditional surrounding earlycon code
serial: 8250_mtk: drop !defined(MODULE) conditional
serial: 8250_uniphier: drop !defined(MODULE) conditional
earlycon: mark earlycon code as __used iif the caller is built-in
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: enable API usage only for initialized mctrl_gpios struct
serial: mctrl_gpio: add modem control read routine
tty/serial/8250: make UART_MCR register access consistent
serial: 8250_mid: Read RX buffer on RX DMA timeout for DNV
serial: 8250_dma: Export serial8250_rx_dma_flush()
dmaengine: hsu: Export hsu_dma_get_status()
tty: serial: 8250: add CON_CONSDEV to flags
tty: serial: samsung: add byte-order aware bit functions
tty: serial: samsung: fixup accessors for endian
serial: sirf: make fifo functions static
serial: mps2-uart: make driver explicitly non-modular
serial: mvebu-uart: free the IRQ in ->shutdown()
serial/bcm63xx_uart: use correct alias naming
...
Pull input fixes from Dmitry Torokhov:
"A few more fixes for the input subsystem:
- restore naming for tsc2005 touchscreens as some userspace match on it
- fix out of bound access in legacy keyboard driver
- fixup in RMI4 driver
Everything is tagged for stable as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc200x - report proper input_dev name
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pinned timers must carry the pinned attribute in the timer structure
itself, so convert the code to the new API.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094341.537448301@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pinned timers must carry the pinned attribute in the timer structure
itself, so convert the code to the new API.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094341.456452642@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As some race conditions are identified in the termination process of tasklets,
enforce the atmel_shutdown() sequence. This way we make sure that no new
tasklets or software timer are scheduled during shutdown process.
An atomic flag is positioned to give this information throughout the code.
We also remove tasklet_disable() calls that were leading to deadlocks while
stopping the driver. A simpler init/kill sequence is used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the transmitter and receiver are stopped when shutting down
the port, and related interrupts are disabled.
Without this:
- New input data may be received into the RX FIFO, possibly
triggering a new RX DMA completion,
- Transfers will still be enabled on a subsequent startup of the UART,
before the UART's FIFOs have been reset, causing reading of stale
data.
Inspired by a patch in the BSP by Koji Matsuoka
<koji.matsuoka.xm@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #if defined(CONFIG_SERIAL_EARLYCON) && !defined(MODULE)
conditional has been added to the OF_EARLYCON_DECLARE() define.
The same conditional can be dropped from 8250_ingenic.c because
the unused symbols will be marked as __maybe_unsed.
Also, the Kconfig dependency can become much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
This commit partially reverts commit 3f5921a60f ("serial:
8250/mediatek: fix building with SERIAL_8250=m").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
Now we can revert commit a2d3ea2f23 ("serial: 8250/uniphier:
fix modular build").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This workaround is needed for the cases, where mctrl_gpio API is used
before mctrl_gpio_init() was invoked. This happens in 8250 during
console initialization, as the driver sets DTR signal.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mctrl_gpio_get_outputs() returns the state of following signals:
RTS, DTR
While defining the routine for reading outputs, fix the comment for
mctrl_gpio_get() routine as it returns only the state of the input
signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DNV, when RX DMA is used and number of bytes received is less than
transfer size, only RX DMA timeout interrupt is sent. When this happens,
read the RX buffer.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export serial8250_rx_dma_flush() for use by SOC UART drivers.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the 8250 as a boot console and the main console results in
messages being printed twice. The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.
Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: Matthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver makes use of the __set_bit() and __clear_bit() functions.
When running under big-endian, these functions don't convert the bit
indexes when working with peripheral registers, leading to the
incorrect bits being set and cleared when running big-endian.
Add two new driver functions for setting and clearing bits that are
byte-order aware.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the serial access code to deal with kernels built for big endian
operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo mask functions should be static as they are not
used outside of the driver. Fix the following warnings by
making them static:
drivers/tty/serial/sirfsoc_uart.h:109:5: warning: symbol 'uart_usp_ff_full_mask' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:117:5: warning: symbol 'uart_usp_ff_empty_mask' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of mps2-uart is:
config SERIAL_MPS2_UART
bool "MPS2 UART port"
depends on ARM || COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Follow commit 89ebc27427 ("drivers/tty: make serial/mvebu-uart.c
explicitly non-modular") as an example of moving modular code to
non-modular:
- remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
- explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
- use arch_initcall instead of module_init and remove module_exit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: <stable@vger.kernel.org>
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm63xx_uart driver uses the of alias for determing its id. Recent
changes in dts files changed the expected 'uartX' to the recommended
'serialX', breaking serial output. Fix this by checking for a 'serialX'
alias as well.
Fixes: e3b992d028 ("MIPS: BMIPS: Improve BCM6328 device tree")
Fixes: 2d52ee82b4 ("MIPS: BMIPS: Improve BCM6368 device tree")
Fixes: 7537d273e2 ("MIPS: BMIPS: Add device tree example for BCM6358")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_M32R_SIO
drivers/tty/serial/Kconfig: bool "M32R SIO I/F"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_VT8500
drivers/tty/serial/Kconfig: bool "VIA VT8500 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_PXA
drivers/tty/serial/Kconfig: bool "PXA serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE and MODULE_ALIAS are both a
no-op for non-modular builds.
We also delete the MODULE_LICENSE tag since that information is
already contained at the top of the file in the comments.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes assignment of port line automatically,
so now user allow to use several MAX310X chips.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves UART registration at module_init initcall,
so this should helps to add multiple chip support in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use resource managed functions devm_gpiochip_add_data() to make
error & exit path a bit simpler.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 IOCTLs uses spinlocks, so move regmap functions into a separate
work queue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
