If the PE contains single PCI function, "pe->pbus" would be NULL.
It's not reliable to be used by pci_domain_nr(). We just grab the
PCI domain number from the PCI host controller (struct pci_controller)
instance.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In function pnv_pci_ioda2_setup_dma_pe(), the IOMMU table type is
set to (TCE_PCI_SWINV_CREATE | TCE_PCI_SWINV_FREE) unconditionally.
It was just set to TCE_PCI by pnv_pci_setup_iommu_table(). So the
primary IOMMU table type (TCE_PCI) is lost. The patch fixes it.
Also, pnv_pci_setup_iommu_table() already set "tbl->it_busno" to
zero and we needn't do it again. The patch removes the redundant
assignment.
The patch also fixes similar issues in pnv_pci_ioda_setup_dma_pe().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch intends to support fundamental reset on PLX downstream
ports. If the PCI device matches any one of the internal table,
which includes PLX vendor ID, bridge device ID, register offset
for fundamental reset and bit, fundamental reset will be done
accordingly. Otherwise, it will fail back to hot reset.
Additional flag (EEH_DEV_FRESET) is introduced to record the last
reset type on the PCI bridge.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the kdump scenario, the first kerenl doesn't shutdown PCI devices
and the kdump kerenl clean PHB IODA table at the early probe time.
That means the kdump kerenl can't support PCI transactions piled
by the first kerenl. Otherwise, lots of EEH errors and frozen PEs
will be detected.
In order to avoid the EEH errors, the PHB is resetted to drop all
PCI transaction from the first kerenl.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, we have 3 types of resets to fulfil PE reset: fundamental,
hot and PHB reset. For the later 2 cases, we need PCI bus reset hold
and settlement delay as specified by PCI spec. PowerNV and pSeries
platforms are running on top of different firmware and some of the
delays have been covered by underly firmware (PowerNV).
The patch makes the delays unified to be done in backend, instead of
EEH core.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Resetting root port has more stuff to do than that for PCIe switch
ports and we should have resetting root port done in firmware instead
of the kernel itself. The problem was introduced by commit 5b2e198e
("powerpc/powernv: Rework EEH reset").
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Once one specific PE has been marked as EEH_PE_ISOLATED, it's in
the middile of recovery or removed permenently. We needn't report
the frozen PE again. Otherwise, we will have endless reporting
same frozen PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:
+-----------------+
| PE#3 p2p#0 |
| p2p#1 |
+-----------------+
|
+-----------------+
| PE#4 pdev#0 |
| pdev#1 |
+-----------------+
PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.
The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces bootarg "eeh=off" to disable EEH functinality.
Also, it creates /sys/kerenl/debug/powerpc/eeh_enable to disable
or enable EEH functionality. By default, we have the functionality
enabled.
For PowerNV platform, we will restore to have the conventional
mechanism of clearing frozen PE during PCI config access if we're
going to disable EEH functionality. Conversely, we will rely on
EEH for error recovery.
The patch also fixes the issue that we missed to cover the case
of disabled EEH functionality in function ioda_eeh_event(). Those
events driven by interrupt should be cleared to avoid endless
reporting.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When calling into eeh_gather_pci_data() on pSeries platform, we
possiblly don't have pci_dev instance yet, but eeh_dev is always
ready. So we use cached capability from eeh_dev instead of pci_dev
for log dump there. In order to keep things unified, we also cache
PCI capability positions to eeh_dev for PowerNV as well.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have suffered recrusive frozen PE a lot, which was caused
by IO accesses during the PE reset. Ben came up with the good
idea to keep frozen PE until recovery (BAR restore) gets done.
With that, IO accesses during PE reset are dropped by hardware
and wouldn't incur the recrusive frozen PE any more.
The patch implements the idea. We don't clear the frozen state
until PE reset is done completely. During the period, the EEH
core expects unfrozen state from backend to keep going. So we
have to reuse EEH_PE_RESET flag, which has been set during PE
reset, to return normal state from backend. The side effect is
we have to clear frozen state for towice (PE reset and clear it
explicitly), but that's harmless.
We have some limitations on pHyp. pHyp doesn't allow to enable
IO or DMA for unfrozen PE. So we don't enable them on unfrozen PE
in eeh_pci_enable(). We have to enable IO before grabbing logs on
pHyp. Otherwise, 0xFF's is always returned from PCI config space.
Also, we had wrong return value from eeh_pci_enable() for
EEH_OPT_THAW_DMA case. The patch fixes it too.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For EEH PowerNV backends, they need use their own PCI config
accesors as the normal one could be blocked during PE reset.
The patch also removes necessary parameter "hose" for the
function ioda_eeh_bridge_reset().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've observed multiple PE reset failures because of PCI-CFG
access during that period. Potentially, some device drivers
can't support EEH very well and they can't put the device to
motionless state before PE reset. So those device drivers might
produce PCI-CFG accesses during PE reset. Also, we could have
PCI-CFG access from user space (e.g. "lspci"). Since access to
frozen PE should return 0xFF's, we can block PCI-CFG access
during the period of PE reset so that we won't get recrusive EEH
errors.
The patch adds flag EEH_PE_RESET, which is kept during PE reset.
The PowerNV/pSeries PCI-CFG accessors reuse the flag to block
PCI-CFG accordingly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For some fields (e.g. LEM, MMIO, DMA) in PHB diag-data dump, it's
meaningless to print them if they have non-zero value in the
corresponding mask registers because we always have non-zero values
in the mask registers. The patch only prints those fieds if we
have non-zero values in the primary registers (e.g. LEM, MMIO, DMA
status) so that we can save couple of lines. The patch also removes
unnecessary spare line before "brdgCtl:" and two leading spaces as
prefix in each line as Ben suggested.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The flag PNV_EEH_STATE_ENABLED is put into pnv_phb::eeh_state,
which is protected by CONFIG_EEH. We needn't that. Instead, we
can have pnv_phb::flags and maintain all flags there, which is
the purpose of the patch. The patch also renames PNV_EEH_STATE_ENABLED
to PNV_PHB_FLAG_EEH.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PHB state PNV_EEH_STATE_REMOVED maintained in pnv_phb isn't
so useful any more and it's duplicated to EEH_PE_ISOLATED. The
patch replaces PNV_EEH_STATE_REMOVED with EEH_PE_ISOLATED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.
The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bitmap in opal_poll_events and opal_handle_interrupt is
big endian, so we need to byteswap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.
This patch release the unnecessary refcount.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this patch I was able to update firmware on an LE kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.
Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.
Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.
The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.
Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.
A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is no need to put a function descriptor in
__secondary_hold_spinloop. Use ppc_function_entry to get the
instruction address and put it in __secondary_hold_spinloop instead.
Also fix an issue where we assumed cur_cpu_spec held a function
descriptor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Some of the assembler files in lib/ make use of the fact that in the
ELFv1 ABI, the caller guarantees to provide stack space to save the
parameter registers r3 ... r10. This guarantee is no longer present
in ELFv2 for functions that have no variable argument list and no
more than 8 arguments.
Change the affected routines to temporarily store registers in the
red zone and/or the top of their own stack frame (in the space
provided to save r31 .. r29, which is actually not used in these
routines).
In opal_query_takeover, simply always allocate a stack frame;
the routine is not performance critical.
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
We are currently using sysfs_schedule_callback() which is deprecated
and about to be removed. Switch to the new interface instead.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This call will not be understood by OPAL, and cause it to add an error
to it's log. Among other things, this is useful for testing the
behaviour of the log as it fills up.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL provides an in-memory circular buffer containing a message log
populated with various runtime messages produced by the firmware.
Provide a sysfs interface /sys/firmware/opal/msglog for userspace to
view the messages.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we wrongly allocate mc_recoverable_range buffer (to hold
recoverable ranges) based on size of the property "mcheck-recoverable-ranges".
This results in allocating less memory to hold available recoverable range
entries from /proc/device-tree/ibm,opal/mcheck-recoverable-ranges.
This patch fixes this issue by allocating mc_recoverable_range buffer based
on number of entries of recoverable ranges instead of device property size.
Without this change we end up allocating less memory and run into memory
corruption issue.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One OPAL call and one device tree property needed byte swapping.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable CPUFreq for PowerNV. Select "performance", "powersave",
"userspace" and "ondemand" governors. Choose "ondemand" to be the
default governor.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPAL defines opal_msg as a big endian struct so we have to
byte swap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
opal_notifier_register() is missing a pending "unregister" variant
and should be exposed to modules.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
This patch enables fetching of various platform sensor data through
OPAL and expects a sensor handle from the driver to pass to OPAL.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables reading and updating of system parameters through
OPAL call.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for notifying the clients of their request
completion. Clients request for the token before making OPAL call
and then wait for the response.
This patch uses messaging infrastructure to pull the data to linux
by registering itself for the message type OPAL_MSG_ASYNC_COMP.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.
Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Flow:
- We register for OPAL notification events.
- OPAL sends new dump available notification.
- We make information on dump available via sysfs
- Userspace requests dump contents
- We retrieve the dump via OPAL interface
- User copies the dump data
- userspace sends ack for dump
- We send ACK to OPAL.
sysfs files:
- We add the /sys/firmware/opal/dump directory
- echoing 1 (well, anything, but in future we may support
different dump types) to /sys/firmware/opal/dump/initiate_dump
will initiate a dump.
- Each dump that we've been notified of gets a directory
in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
as this is what's used elsewhere to identify the dump).
- Each dump has files: id, type, dump and acknowledge
dump is binary and is the dump itself.
echoing 'ack' to acknowledge (currently any string will do) will
acknowledge the dump and it will soon after disappear from sysfs.
OPAL APIs:
- opal_dump_init()
- opal_dump_info()
- opal_dump_read()
- opal_dump_ack()
- opal_dump_resend_notification()
Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.
We export each log entry as a directory in /sys/firmware/opal/elog/
Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.
Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).
If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.
A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.
On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.
I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During "Fast-sleep" and deeper power savings state, decrementer and
timebase could be stopped making it out of sync with rest
of the cores in the system.
Add a firmware call to request platform to resync timebase
using low level platform methods.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to unmangle the full address, not just the register
number, and we also need to support the real indirect bit
being set for in-kernel uses.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13]
As Ben suggested, the patch prints PHB diag-data with multiple
fields in one line and omits the line if the fields of that
line are all zero.
With the patch applied, the PHB3 diag-data dump looks like:
PHB3 PHB#3 Diag-data (Version: 1)
brdgCtl: 00000002
RootSts: 0000000f 00400000 b0830008 00100147 00002000
nFir: 0000000000000000 0030006e00000000 0000000000000000
PhbSts: 0000001c00000000 0000000000000000
Lem: 0000000000100000 42498e327f502eae 0000000000000000
InAErr: 8000000000000000 8000000000000000 0402030000000000 0000000000000000
PE[ 8] A/B: 8480002b00000000 8000000000000000
[ The current diag data is so big that it overflows the printk
buffer pretty quickly in cases when we get a handful of errors
at once which can happen. --BenH
]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PHB diag-data is important to help locating the root cause for
EEH errors such as frozen PE or fenced PHB. However, the EEH core
enables IO path by clearing part of HW registers before collecting
this data causing it to be corrupted.
This patch fixes this by dumping the PHB diag-data immediately when
frozen/fenced state on PE or PHB is detected for the first time in
eeh_ops::get_state() or next_error() backend.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The core idle loop now takes care of it. We need to add the runlatch
function calls to the idle routines which was earlier taken care of by
the arch specific idle routine.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/n/tip-nr4mtbkkzf2oomaj85m24o7c@git.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing reset in order to recover the affected PE, we issue
hot reset on PE primary bus if it's not root bus. Otherwise, we
issue hot or fundamental reset on root port or PHB accordingly.
For the later case, we didn't cover the situation where PE only
includes root port and it potentially causes kernel crash upon
EEH error to the PE.
The patch reworks the logic of EEH reset to improve the code
readability and also avoid the kernel crash.
Cc: stable@vger.kernel.org
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Following patch ports the cpuidle framework for powernv
platform and also implements a cpuidle back-end powernv
idle driver calling on to power7_nap and snooze idle states.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Its possible that OPAL may be writing to host memory during
kexec (like dump retrieve scenario). In this situation we might
end up corrupting host memory.
This patch makes OPAL sync call to make sure OPAL stops
writing to host memory before kexec'ing.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sometimes, especially in sinario of loading another kernel with kdump,
we got EEH error on non-existing PE. That means the PEEV / PEST in
the corresponding PHB would be messy and we can't handle that case.
The patch escalates the error to fenced PHB so that the PHB could be
rested in order to revoer the errors on non-existing PEs.
Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For one PCI error relevant OPAL event, we possibly have multiple
EEH errors for that. For example, multiple frozen PEs detected on
different PHBs. Unfortunately, we didn't cover the case. The patch
enumarates the return value from eeh_ops::next_error() and change
eeh_handle_special_event() and eeh_ops::next_error() to handle all
existing EEH errors.
As Ben pointed out, we needn't list_for_each_entry_safe() since we
are not deleting any PHB from the hose_list and the EEH serialized
lock should be held while purging EEH events. The patch covers those
suggestions as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present we assume candidate image is <= 256MB. But in P8,
candidate image size can go up to 750MB. Hence increasing
candidate image max size to 1GB.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch implements the EEH operation backend restore_config()
for PowerNV platform. That relies on OPAL API opal_pci_reinit()
where we reinitialize the error reporting properly after PE or
PHB reset.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After reset on the specific PE or PHB, we never configure AER
correctly on PowerNV platform. We needn't care it on pSeries
platform. The patch introduces additional EEH operation eeh_ops::
restore_config() so that we have chance to configure AER correctly
for PowerNV platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't have IO ports on PHB3 and the assignment of variable
"iomap_off" on PHB3 is meaningless. The patch just removes the
unnecessary assignment to the variable. The code change should
have been part of commit c35d2a8c ("powerpc/powernv: Needn't IO
segment map for PHB3").
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
The one instance where we add an include for init.h covers off
a case where that file was implicitly getting it from another
header which itself didn't need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge a pile of fixes that went into the "merge" branch (3.13-rc's) such
as Anton Little Endian fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the generic iommu backend code to use the
it_page_shift field to determine the iommu page size instead of
using hardcoded values.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a it_page_shift field to struct iommu_table and
initiliases it to 4K for all platforms.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc iommu uses a hardcoded page size of 4K. This patch changes
the name of the IOMMU_PAGE_* macros to reflect the hardcoded values. A
future patch will use the existing names to support dynamic page
sizes.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are passing pointers to the firmware for reads, we need to properly
convert the result as OPAL is always BE.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
opal_xscom_read uses a pointer to return the data so we need
to byteswap it on LE builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have recently found out that no iommu_groups could be found under
/sys/ on a P8. That prevents PCI passthrough from working.
During my investigation, I found out there seems to be a missing
iommu_register_group for PHB3. The following patch seems to fix the
problem. After applying it, I see iommu_groups under
/sys/kernel/iommu_groups/, and can also bind vfio-pci to an adapter,
which gives me a device at /dev/vfio/.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Get the memory errors reported by opal and plumb it into memory poison
infrastructure. This patch uses new messaging channel infrastructure to
pull the fsp memory errors to linux.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we continue to poll get/set_rtc_time even when we know they
are not working.
This changes it so that if it fails at boot time we remove the ppc_md
get/set_rtc_time hooks so that we don't end up polling known broken
calls.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When hitting frozen PE or fenced PHB, it's always indicative to
have dumped PHB diag-data for further analysis and diagnosis.
However, we never dump that for the cases. The patch intends to
dump PHB diag-data at the backend of eeh_ops::get_log() for PowerNV
platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prior to the completion of PCI enumeration, we actively detects
EEH errors on PCI config cycles and dump PHB diag-data if necessary.
The EEH backend also dumps PHB diag-data in case of frozen PE or
fenced PHB. However, we are using different functions to dump the
PHB diag-data for those 2 cases.
The patch merges the functions for dumping PHB diag-data to one so
that we can avoid duplicate code. Also, we never dump PHB3 diag-data
during PCI config cycles with frozen PE. The patch fixes it as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current implementation of IOMMU on sPAPR does not use iommu_ops
and therefore does not call IOMMU API's bus_set_iommu() which
1) sets iommu_ops for a bus
2) registers a bus notifier
Instead, PCI devices are added to IOMMU groups from
subsys_initcall_sync(tce_iommu_init) which does basically the same
thing without using iommu_ops callbacks.
However Freescale PAMU driver (https://lkml.org/lkml/2013/7/1/158)
implements iommu_ops and when tce_iommu_init is called, every PCI device
is already added to some group so there is a conflict.
This patch does 2 things:
1. removes the loop in which PCI devices were added to groups and
adds explicit iommu_add_device() calls to add devices as soon as they get
the iommu_table pointer assigned to them.
2. moves a bus notifier to powernv code in order to avoid conflict with
the notifier from Freescale driver.
iommu_add_device() and iommu_del_device() are public now.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move SG list and entry structure to header file so that
it can be used in other places as well.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Opal now has a new messaging infrastructure to push the messages to
linux in a generic format for different type of messages using only one
event bit. The format of the opal message is as below:
struct opal_msg {
uint32_t msg_type;
uint32_t reserved;
uint64_t params[8];
};
This patch allows clients to subscribe for notification for specific
message type. It is upto the subscriber to decipher the messages who showed
interested in receiving specific message type.
The interface to subscribe for notification is:
int opal_message_notifier_register(enum OpalMessageType msg_type,
struct notifier_block *nb)
The notifier will fetch the opal message when available and notify the
subscriber with message type and the opal message. It is subscribers
responsibility to copy the message data before returning from notifier
callback.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add basic error handling in machine check exception handler.
- If MSR_RI isn't set, we can not recover.
- Check if disposition set to OpalMCE_DISPOSITION_RECOVERED.
- Check if address at fault is inside kernel address space, if not then send
SIGBUS to process if we hit exception when in userspace.
- If address at fault is not provided then and if we get a synchronous machine
check while in userspace then kill the task.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we are ready to handle machine check directly in linux, do not
register with firmware to handle machine check exception.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When machine check real mode handler can not continue into host kernel
in V mode, it returns from the interrupt and we loose MCE event which
never gets logged. In such a situation queue up the MCE event so that
we can log it later when we get back into host kernel with r1 pointing to
kernel stack e.g. during syscall exit.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we handle machine check in linux, the MCE decoding should also
take place in linux host. This info is crucial to log before we go down
in case we can not handle the machine check errors. This patch decodes
and populates a machine check event which contain high level meaning full
MCE information.
We do this in real mode C code with ME bit on. The MCE information is still
available on emergency stack (in pt_regs structure format). Even if we take
another exception at this point the MCE early handler will allocate a new
stack frame on top of current one. So when we return back here we still have
our MCE information safe on current stack.
We use per cpu buffer to save high level MCE information. Each per cpu buffer
is an array of machine check event structure indexed by per cpu counter
mce_nest_count. The mce_nest_count is incremented every time we enter
machine check early handler in real mode to get the current free slot
(index = mce_nest_count - 1). The mce_nest_count is decremented once the
MCE info is consumed by virtual mode machine exception handler.
This patch provides save_mce_event(), get_mce_event() and release_mce_event()
generic routines that can be used by machine check handlers to populate and
retrieve the event. The routine release_mce_event() will free the event slot so
that it can be reused. Caller can invoke get_mce_event() with a release flag
either to release the event slot immediately OR keep it so that it can be
fetched again. The event slot can be also released anytime by invoking
release_mce_event().
This patch also updates kvm code to invoke get_mce_event to retrieve generic
mce event rather than paca->opal_mce_evt.
The KVM code always calls get_mce_event() with release flags set to false so
that event is available for linus host machine
If machine check occurs while we are in guest, KVM tries to handle the error.
If KVM is able to handle MC error successfully, it enters the guest and
delivers the machine check to guest. If KVM is not able to handle MC error, it
exists the guest and passes the control to linux host machine check handler
which then logs MC event and decides how to handle it in linux host. In failure
case, KVM needs to make sure that the MC event is available for linux host to
consume. Hence KVM always calls get_mce_event() with release flags set to false
and later it invokes release_mce_event() only if it succeeds to handle error.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently have a user visible CONFIG_POWERNV_MSI option, but it
doesn't actually disable MSI for powernv. The MSI code is always built,
what it does disable is the inclusion of the MSI bitmap code, which
leads to a build error.
eg, with PPC_POWERNV=y and POWERNV_MSI=n we get:
arch/powerpc/platforms/built-in.o: In function `.pnv_teardown_msi_irqs':
pci.c:(.text+0x3558): undefined reference to `.msi_bitmap_free_hwirqs'
We don't really need a POWERNV_MSI symbol, just have the MSI bitmap code
depend directly on PPC_POWERNV.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have only used cpu_to_chip_id() in the topology code,
which is only used on SMP builds. However my recent commit a4da0d5
"Implement arch_get_random_long/int() for powernv" added a usage when
SMP=n, breaking the build.
Move cpu_to_chip_id() into prom.c so it is available for SMP=n builds.
We would move the extern to prom.h, but that breaks the include in
topology.h. Instead we leave it in smp.h, but move it out of the
CONFIG_SMP #ifdef. We also need to include asm/smp.h in rng.c, because
the linux version skips asm/smp.h on UP. What a mess.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
We're assigning PE numbers after the completion of PCI probe. During
the PCI probe, we had PE#0 as the super container to encompass all
PCI devices. However, that's inappropriate since PELTM has ascending
order of priority on search on P7IOC. So we need PE#127 takes the
role that PE#0 has previously. For PHB3, we still have PE#0 as the
reserved PE.
The patch supposes that the underly firmware has built the RID to
PE# mapping after resetting IODA tables: all PELTM entries except
last one has invalid mapping on P7IOC, but all RTEs have binding
to PE#0. The reserved PE# is being exported by firmware by device
tree.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need add PE to its own PELTV. Otherwise, the errors originated
from the PE might contribute to other PEs. In the result, we can't
clear up the error successfully even we're checking and clearing
errors during access to PCI config space.
Cc: stable@vger.kernel.org
Reported-by: kalshett@in.ibm.com
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Indirect XSCOM addresses normally have the top bit set (of the 64-bit
address). This doesn't work via the normal debugfs interface, so we use
a different encoding, which we need to convert before calling OPAL.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On P8, XSCOM addresses has a special "indirect" form that
requires more than 32-bits, so let's use u64 everywhere in
the code instead of u32.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Code update interface for powernv platform. This provides
sysfs interface to pass new image, validate, update and
commit images.
This patch includes:
- Below OPAL APIs for code update
- opal_validate_flash()
- opal_manage_flash()
- opal_update_flash()
- Create below sysfs files under /sys/firmware/opal
- image : Interface to pass new FW image
- validate_flash : Validate candidate image
- manage_flash : Commit/Reject operations
- update_flash : Flash new candidate image
Updating Image:
"update_flash" is an interface to indicate flash new FW.
It just passes image SG list to FW. Actual flashing is done
during system reboot time.
Note:
- SG entry format:
I have kept version number to keep this list similar to what
PAPR is defined.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create /sys/firmware/opal directory. We wil use this
interface to fetch opal error logs, firmware update, etc.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The condition register (CR) is a 32 bit quantity so we should use
32 bit loads and stores.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Caused by commit a4da0d50b2 ("powerpc: Implement
arch_get_random_long/int() for powernv") from the powerpc tree
interacting with commit b5b4bb3f6a ("of: only include prom.h on sparc")
from the dt-rh tree.
I added this merge fix patch (which will need to be sent to Linus when
these two trees get merged, or could be applied now to the powerpc tree):
[ Also add linux/smp.h to get cpu_to_chip_id -- BenH ]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Topic branch for commits that the KVM tree might want to pull
in separately.
Hand merged a few files due to conflicts with the LE stuff
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The existing TCE machine calls (tce_build and tce_free) only support
virtual mode as they call __raw_writeq for TCE invalidation what
fails in real mode.
This introduces tce_build_rm and tce_free_rm real mode versions
which do mostly the same but use "Store Doubleword Caching Inhibited
Indexed" instruction for TCE invalidation.
This new feature is going to be utilized by real mode support of VFIO.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds function ioda_eeh_phb3_phb_diag() to dump PHB3
PHB diag-data. That's called while detecting informative errors
or frozen PE on the specific PHB.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Each PHB instance (struct pnv_phb) has its corresponding log blob,
which is used to hold the retrieved error log from firmware. The
current size of that (4096) isn't enough for PHB3 case and the patch
makes that double to 8192.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch prints the error number while failing to retrieve error
log from firmware. It's helpful for debugging.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For now, we only support outbound error injection. Actually, the
hardware supports injecting inbound errors as well. The patch enables
to inject inbound errors.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH isn't enabled for PHB3 and the patch intends to enable it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL v3 provides interfaces to access the chips XSCOM, expose
this via the existing scom infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the plumbing to implement arch_get_random_long/int(). It didn't seem
worth adding an extra ppc_md hook for int, so we reuse the one for long.
Add an implementation for powernv based on the hwrng found in power7+
systems. We whiten the output of the hwrng, and the result passes all
the dieharder tests.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pnv_pci_setup_bml_iommu was missing a byteswap of a device
tree property.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sparse caught an issue where opal_set_rtc_time was incorrectly
byteswapping. Also fix a number of sparse warnings.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powernv exception handlers are not ready to take exceptions
in little endian mode, so disable them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When removing prom.h include by of.h, several OF headers will no longer
be implicitly included. Add explicit includes of of_*.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: linuxppc-dev@lists.ozlabs.org
With OPAL v3 we can return secondary CPUs to firmware on kexec. This
allows firmware to do various cleanups making things generally more
reliable, and will enable the "new" kernel to call OPAL to perform
some reconfiguration tasks early on that can only be done while
all the CPUs are in firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
changes for V4:
- changes the type of frozen_pe_no from %d to %llu
in pr_devel()
'pe_no' hasn't been defined, it should be an typo error,
it should be 'frozen_pe_no'.
Also '__func__' has missed in IODA_EEH_DBG(),
For safety reasons, use pr_devel() directly, instead
of use IODA_EEH_DBG()
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Legacy UARTs can exist on PowerNV, memory-mapped ones on PCI
or IO based ones on the LPC bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some machines might provide the console via a different mechanism
such as direct access to a UART from Linux, in which case OPAL
might not expose any console. In that case, the code would cause
a NULL dereference.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This uses the hooks provided by CONFIG_PPC_INDIRECT_PIO to
implement a set of hooks for IO port access to use the LPC
bus via OPAL calls for the first 64K of IO space
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PHB3 doesn't support IO ports and we needn't IO segment map for that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The index of one specific PCI controller (struct pci_controller::
global_number) can tell that it's primary one or not. So we needn't
additional variable for that and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch enables fetching bus range from device-tree for the
specific PHB. If we can't get that from device-tree, the default
range [0 255] will be used.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't free PHB instance (struct pnv_phb) on error to creating
the associated PCI controler (struct pci_controller). The patch
fixes that. Also, the output messages have been cleaned for a bit
so that they looks unified for IODA_1/2 cases.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
T4, Cell, powernv, and pseries had the same implementation, so switch
them to use a generic version. A2 apparently had a version, but
removed it at some point, so we remove the declaration, too.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mark pnv_pci_init_ioda2_phb() as __init. It is called only from an
init function (pnv_pci_init()), and it calls an init function
(pnv_pci_init_ioda_phb()):
pnv_pci_init # init
pnv_pci_init_ioda2_phb # non-init
pnv_pci_init_ioda_phb # init
This should fix a section mismatch warning.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs
entries for the corresponding EEH device (then PCI device) has been
added or removed, in order to avoid race condition.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While restoring BARs for one specific PCI device, the pci_dev
instance should have been released. So it's not reliable to use
the pci_dev instance on restoring BARs. However, we still need
some information (e.g. PCIe capability position, header type) from
the pci_dev instance. So we have to store those information to
EEH device in advance.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error happens to one specific PE, some devices with drivers
supporting EEH won't except hotplug on the device. However, there
might have other deivces without driver, or with driver without EEH
support. For the case, we need do partial hotplug in order to make
sure that the PE becomes absolutely quite during reset. Otherise,
the PE reset might fail and leads to failure of error recovery.
The current code doesn't handle that 'mixed' case properly, it either
uses the error callbacks to the drivers, or tries hotplug, but doesn't
handle a PE (EEH domain) composed of a combination of the two.
The patch intends to support so-called "partial" hotplug for EEH:
Before we do reset, we stop and remove those PCI devices without
EEH sensitive driver. The corresponding EEH devices are not detached
from its PE, but with special flag. After the reset is done, those
EEH devices with the special flag will be scanned one by one.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So because those things always end up in trainwrecks... In 7846de406
we moved back the iommu initialization earlier, essentially undoing
37f02195b which was causing us endless trouble... except that in the
meantime we had merged 959c9bdd58 (to workaround the original breakage)
which is now ... broken :-)
This fixes it by doing a partial revert of the latter (we keep the
ppc_md. path which will be needed in the hotplug case, which happens
also during some EEH error recovery situations).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.10]
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the powerpc uses of the __cpuinit macros. There
are no __CPUINIT users in assembly files in powerpc.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we're using the combo (PCI bus + devfn) in the PCI
config accessors and PCI config accessors in EEH depends on them.
However, it's not safe to refer the PCI bus which might have been
removed during hotplug. So we're using device node in the PCI
config accessors and the corresponding backends just reuse them.
The patch also fix one potential risk: We possiblly have frozen
PE during the early PCI probe time, but we haven't setup the PE
mapping yet. So the errors should be counted to PE#0.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We needn't the the whole backtrace other than one-line message in
the error reporting interrupt handler. For errors triggered by
access PCI config space or MMIO, we replace "WARN(1, ...)" with
pr_err() and dump_stack(). The patch also adds more output messages
to indicate what EEH core is doing. Besides, some printk() are
replaced with pr_warning().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On the PowerNV platform, the EEH address cache isn't built correctly
because we skipped the EEH devices without binding PE. The patch
fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have 2 fields in "struct pnv_phb" to trace the states. The patch
replace the fields with one and introduces flags for that. The patch
doesn't impact the logic.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch creates one debugfs directory ("powerpc/PCIxxxx") for
each PHB so that we can hook EEH error injection debugfs entry
there in proceeding patch.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch registers OPAL event notifier and process the PCI errors
from firmware. If we have pending PCI errors, special EEH event
(without binding PE) will be sent to EEH core for processing.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While we're restarting or powering off the system, we needn't
the OPAL notifier any more. So just to disable that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch implements a notifier to receive a notification on OPAL
event mask changes. The notifier is only called as a result of an OPAL
interrupt, which will happen upon reception of FSP messages or PCI errors.
Any event mask change detected as a result of opal_poll_events() will not
result in a notifier call.
[benh: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch enables EEH check and let EEH core to process the EEH
errors for PowerNV platform while accessing config space. Originally,
the implementation already had mechanism to check EEH errors and
tried to recover from them. However, we never let EEH core to handle
the EEH errors.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch initializes EEH for PowerNV platform. Because the OPAL
APIs requires HUB ID, we need trace that through struct pnv_phb.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds EEH backends for PowerNV platform. It's notable that
part of those EEH backends call to the I/O chip dependent backends.
[Removed pointless change to eeh_pseries.c -- BenH]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch implements the backend for EEH core to retrieve next
EEH error to handle. For the informational errors, we won't bother
the EEH core. Otherwise, the EEH should take appropriate actions
depending on the return value:
0 - No further errors detected
1 - Frozen PE
2 - Fenced PHB
3 - Dead PHB
4 - Dead IOC
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds backends to retrieve error log and configure p2p
bridges for the indicated PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds the I/O chip backend to do PE reset. For now, we
focus on PCI bus dependent PE. If PHB PE has been put into error
state, the PHB will take complete reset. Besides, the root bridge
will take fundamental or hot reset accordingly if the indicated
PE locates at the toppest of PCI hierarchy tree. Otherwise, the
upstream p2p bridge will take hot reset.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds I/O chip backend to retrieve the state for the
indicated PE. While the PE state is temperarily unavailable,
the upper layer (powernv platform) should return default delay
(1 second).
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds the backend to enable or disable EEH functionality
for the specified PE. The backend is also used to enable MMIO or
DMA path for the problematic PE. It's notable that all PEs on
PowerNV platform support EEH functionality by default, and we
disallow to disable EEH for the specific PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The post initialization (struct eeh_ops::post_init) is called after
the EEH probe is done. On the other hand, the EEH core post
initialization is designed to call platform and then I/O chip backend
on PowerNV platform.
The patch adds the backend for I/O chip to notify the platform
that the specific PHB is ready to supply EEH service.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For EEH on PowerNV platform, the overall architecture is different
from that on pSeries platform. In order to support multiple I/O chips
in future, we split EEH to 3 layers for PowerNV platform: EEH core,
platform layer, I/O layer. It would give EEH implementation on PowerNV
platform much more flexibility in future.
The patch adds the EEH backend for P7IOC.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch synchronizes OPAL APIs between kernel and firmware. Also,
we starts to replace opal_pci_get_phb_diag_data() with the similar
opal_pci_get_phb_diag_data2() and the former OPAL API would return
OPAL_UNSUPPORTED from now on.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
'system_state < SYSTEM_RUNNING' will have same effect
with 'system_state == SYSTEM_BOOTING', but the later
one is more clearer.
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This initializes IOMMU groups based on the IOMMU configuration
discovered during the PCI scan on POWERNV (POWER non virtualized)
platform. The IOMMU groups are to be used later by the VFIO driver,
which is used for PCI pass through.
It also implements an API for mapping/unmapping pages for
guest PCI drivers and providing DMA window properties.
This API is going to be used later by QEMU-VFIO to handle
h_put_tce hypercalls from the KVM guest.
The iommu_put_tce_user_mode() does only a single page mapping
as an API for adding many mappings at once is going to be
added later.
Although this driver has been tested only on the POWERNV
platform, it should work on any platform which supports
TCE tables. As h_put_tce hypercall is received by the host
kernel and processed by the QEMU (what involves calling
the host kernel again), performance is not the best -
circa 220MB/s on 10Gb ethernet network.
To enable VFIO on POWER, enable SPAPR_TCE_IOMMU config
option and configure VFIO as required.
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The zImage.epapr wrapper allows to use zImages when booting via a flat
device-tree which can be used on powernv.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the quirk itself to pci_64.c as to get built on all ppc64
platforms (the only ones with a pci_dn), factors the two implementations
of get_pdn() into a single pci_get_dn() and use the quirk to do 32-bit
MSIs on IODA based powernv platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use two flags, one to indicate an invalidation is needed after
creating a new entry and one to indicate an invalidation is needed
after removing an entry. However we were testing the wrong flag
in the remove case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code fails to handle kexec on OPALv2. This fixes it
and adds code to improve the situation on OPALv3 where we can
query the CPU status from the firmware and decide what to do
based on that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We add a machine_shutdown hook that frees the OPAL interrupts
(so they get masked at the source and don't fire while kexec'ing)
and which triggers an IODA reset on all the PCIe host bridges
which will have the effect of blocking all DMAs and subsequent
PCIs interrupts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the firmware returns an error such as "closed" (or hardware
error), we should drop characters.
Currently we only do that when a firmware compatible with OPAL v2
APIs is detected, in the code that calls opal_console_write_buffer_space(),
which didn't exist with OPAL v1 (or didn't work).
However, when enabling early debug consoles, the flag indicating
that v2 is supported isn't set yet, causing us, in case of errors
or closed console, to spin forever.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.
This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.
This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The property should be "ibm,power8-pciex", not "ibm,p8-pciex". The latter
was changed in FW because it was inconsistent with the rest of the nodes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If OPAL returns an error, propagate it upward rather than spinning
seconds waiting for a CPU that will never show up
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the OPAL exception vectors are registered before the feature
fixups are processed. This means that the now-firmware-owned vectors
will likely be overwritten by the kernel.
This change moves the exception registration code to an early initcall,
rather than at machine_init time.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ben found the root cause. Commit 37f02195be
("powerpc/pci: fix PCI-e devices rescan issue on powerpc platform")
overwrites the IOMMU table of PCI device while enabling PCI device.
The patch intends to fix the IOMMU table after that point.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch intends to build 32-bits DMA space for individual PEs on
PHB3. The TVE# is recognized by the combo of PE# and fixed bits
from DMA address, which is zero for 32-bits DMA space.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The TCE should be invalidated while it's created or free'd. The
approach to do that for IODA1 and IODA2 compliant PHBs are different.
So the patch differentiate them with different functions called to
do that for IODA1 and IODA2 compliant PHBs. It's notable that the
PCI address is used to invalidate the corresponding TCE on IODA2
compliant PHB3.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EOI handler of MSI/MSI-X interrupts for P8 (PHB3) need additional
steps to handle the P/Q bits in IVE before EOIing the corresponding
interrupt. The patch changes the EOI handler to cover that. we have
individual IRQ chip in each PHB instance. During the MSI IRQ setup
time, the IRQ chip is copied over from the original one for that IRQ,
and the EOI handler is patched with the one that will handle the P/Q
bits (As Ben suggested).
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As Michael Ellerman suggested, to add CONFIG_POWERNV_MSI for PowerNV
platform. That's similar to CONFIG_PSERIES_MSI for pSeries platform.
For now, we don't make it dependent on CONFIG_EEH since it's not ready
to enable that yet.
Apart from that, we also enable CONFIG_PPC_MSI_BITMAP on selecting
CONFIG_POWERNV_MSI.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch intends to initialize PHB3 during system boot stage. The
flag "PNV_PHB_MODEL_PHB3" is introduced to differentiate IODA2
compatible PHB3 from other types of PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As Michael Ellerman mentioned, arch/powerpc/sysdev/msi_bitmap.c
already implemented bitmap to manage (alloc/free) MSI interrupts.
The patch intends to use that mechanism to manage MSI interrupts
for PowerNV platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There're couples of functions defined to print debugging messages
during initializing P7IOC. However, we got bogus output from those
functions like pe_info(). The problem here is that the message
level (the first parameter to printk()) isn't printable and that
caused the bogus output.
The patch fixes the issue by merging __pe_printk() to the macro
define_pe_printk_level() so that we can pass the message level
directly to printk().
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't need them anymore. The patch removes those functions.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the PCI probe flags "PCI_PROBE_ONLY | PCI_REASSIGN_ALL_RSRC"
used on powernv platform. That means the platform has to do the PCI
resource assignment by itself.
The patch changes the PCI probe flag to "PCI_REASSIGN_ALL_RSRC" so
that the PCI core will do the resource assignment. Also, the I/O
and MMIO minimal alignment for P2P bridges have been configured
while doing fixup for the PHBs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 arrays introduced to trace which PE has occupied the
corresponding resource (I/O or MMIO) segment. However, we didn't
allocate enough memory for them and that possiblly leads to PE
descriptor corruption.
The patch fixes that by allocating enough memory for those 2 arrays.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While the device driver or PCI core tries to enable PCI device, the
platform dependent callback "ppc_md.pcibios_enable_device_hook" will
be called to check if there has one associated PE for the PCI device.
If we don't have the associated PE for the PCI device, it's not allowed
to enable the PCI device. Unfortunately, there might have some cases
we have to enable the PCI device (e.g. P2P bridge), but the PEs have
not been created yet.
The patch handles the unfortunate cases. Each PHB (struct pnv_phb)
has one field "initialized" to trace if the PEs have been created
and configured or not. When the PEs are not available, we won't check
the associated PE for the PCI device to be enabled.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces additional wrapper function to call the original
implementation so that the DMA can be configured for all existing PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 types of PCI bus sensitive PEs: (A) The PE includes
single PCI bus. (B) The PE includes the PCI bus and all the subordinate
PCI buses, and the patch tries to assign I/O and MMIO resources
based on created PEs. Fortunately, we figured out unified scheme
to do resource assignment for all types of PCI bus based PEs according
to Ben's idea:
- Resource assignment based on PE from top to bottom.
- The soureces, either I/O or MMIO, of the PE are figured out
from the assigned PCI bus.
- The occupied resource by parent PE could possibilly be overrided
by children PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The resource (I/O and MMIO) will be assigned on basis of PE from
top to bottom so that we can implement the trick here: the resource
that has been assigned to parent PE could be taken by child PE if
necessary.
The current implementation already has PE list per PHB basis, but
the list doesn't meet our requirment: tracing PE based on their
cration time from top to bottom. So the patch does rename for the
DMA based PE list and introduces the list to trace the PEs sequentially
based on their creation time.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, there're 2 types of PCI bus sensitive PEs: (A) The PE
includes single PCI bus. (B) The PE includes the PCI bus and all
the subordinate PCI buses. At present, we'd like to put PCI bus
originated by PCI-e link to form PE that contains single PCI bus,
and the PCIe-to-PCI bridge will form the 2nd type of PE. We don't
figure out to detect PLX bridge yet. Once we can detect PLX bridge
some day, we have to put PCI buses originated from the downstream
port of PLX bridge to the 2nd type of PE.
The patch changes the original implementation for a little bit
to support 2 types of PCI bus sensitive PEs described as above.
Also, the function used to retrieve the corresponding PE according
to the given PCI device has been changed based on that because each
PCI device should trace the directly associated PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
The patch implements ppc_md.pcibios_window_alignment for powernv
platform so that the resource reassignment in PCI core will be
done according to the I/O and memory alignment returned from
powernv platform. The alignments returned from powernv platform
is closely depending on the scheme for PE segmenting. Besides,
the patch isn't useful for now, but the subsequent patches will
be working based on it.
[bhelgaas: use pci_pcie_type() since pci_dev.pcie_type was removed]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The upcoming VFIO support requires a way to know which
entry in the TCE map is not empty in order to do cleanup
at QEMU exit/crash. This patch adds such functionality
to POWERNV platform code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan