commit 7bc1a0f9e1 upstream.
On arm64, the global variable memstart_addr represents the physical
address of PAGE_OFFSET, and so physical to virtual translations or
vice versa used to come down to simple additions or subtractions
involving the values of PAGE_OFFSET and memstart_addr.
When support for 52-bit virtual addressing was introduced, we had to
deal with PAGE_OFFSET potentially being outside of the region that
can be covered by the virtual range (as the 52-bit VA capable build
needs to be able to run on systems that are only 48-bit VA capable),
and for this reason, another translation was introduced, and recorded
in the global variable physvirt_offset.
However, if we go back to the original definition of memstart_addr,
i.e., the physical address of PAGE_OFFSET, it turns out that there is
no need for two separate translations: instead, we can simply subtract
the size of the unaddressable VA space from memstart_addr to make the
available physical memory appear in the 48-bit addressable VA region.
This simplifies things, but also fixes a bug on KASLR builds, which
may update memstart_addr later on in arm64_memblock_init(), but fails
to update vmemmap and physvirt_offset accordingly.
Fixes: 5383cc6efe ("arm64: mm: Introduce vabits_actual")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Link: https://lore.kernel.org/r/20201008153602.9467-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35a824c31 ]
With UBSAN enabled and building with clang, there are occasionally
warnings like
WARNING: modpost: vmlinux.o(.text+0xc533ec): Section mismatch in reference from the function arch_atomic64_or() to the variable .init.data:numa_nodes_parsed
The function arch_atomic64_or() references
the variable __initdata numa_nodes_parsed.
This is often because arch_atomic64_or lacks a __initdata
annotation or the annotation of numa_nodes_parsed is wrong.
for functions that end up not being inlined as intended but operating
on __initdata variables. Mark these as __always_inline, along with
the corresponding asm-generic wrappers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210108092024.4034860-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a5f1b67ec upstream.
We reset the guest's view of PMCR_EL0 unconditionally, based on
the host's view of this register. It is however legal for an
implementation not to provide any PMU, resulting in an UNDEF.
The obvious fix is to skip the reset of this shadow register
when no PMU is available, sidestepping the issue entirely.
If no PMU is available, the guest is not able to request
a virtual PMU anyway, so not doing nothing is the right thing
to do!
It is unlikely that this bug can hit any HW implementation
though, as they all provide a PMU. It has been found using nested
virt with the host KVM not implementing the PMU itself.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201210083059.1277162-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca4e514774 upstream.
ARMv8.2 introduced TTBCR2, which shares TCR_EL1 with TTBCR.
Gracefully handle traps to this register when HCR_EL2.TVM is set.
Cc: stable@vger.kernel.org
Reported-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3d07c3b3a8 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: ed5e8f6891 ("arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/12506964ca5d5f936579a280ad0a7e7f9a0a2d4c.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c183c406c4 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240 ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c605e00c ]
The max frequency for the w25q32 (VIM v1.2) and w25q128 (VIM v1.4) spifc
chip should be 104Mhz not 30MHz.
Fixes: b8b74dda39 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125024001.19036-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0570a575a ]
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e2 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4076a007bd ]
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa669a994 ]
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b26c1a034 ]
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c30 ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53e573dc39 ]
The CAT875 sub board from Silicon Linux uses Realtek phy and the driver
does not support rxc-skew-ps property.
Fixes: 6b170cd3ed ("arm64: dts: renesas: cat875: Add ethernet support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201015132350.8360-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca1314d73e ]
In el0_svc_common() we unmask exceptions before we call user_exit(), and
so there's a window where an IRQ or debug exception can be taken while
RCU is not watching. In do_debug_exception() we account for this in via
debug_exception_{enter,exit}(), but in the el1_irq asm we do not and we
call trace functions which rely on RCU before we have a guarantee that
RCU is watching.
Let's avoid this by having el0_svc_common() exit userspace before
unmasking exceptions, matching what we do for all other EL0 entry paths.
We can use user_exit_irqoff() to avoid the pointless save/restore of IRQ
flags while we're sure exceptions are masked in DAIF.
The workaround for Cortex-A76 erratum 1463225 may trigger a debug
exception before this point, but the debug code invoked in this case is
safe even when RCU is not watching.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201130115950.22492-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb31949693 ]
Commit ff4c371d2b ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2013a4b684 ]
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0011c6d182 ]
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
[1]
https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201104162356.1251-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1741e18737 ]
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff1712f953 upstream.
With hardware dirty bit management, calling pte_wrprotect() on a writable,
dirty PTE will lose the dirty state and return a read-only, clean entry.
Move the logic from ptep_set_wrprotect() into pte_wrprotect() to ensure that
the dirty bit is preserved for writable entries, as this is required for
soft-dirty bit management if we enable it in the future.
Cc: <stable@vger.kernel.org>
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07509e10dc upstream.
pte_accessible() is used by ptep_clear_flush() to figure out whether TLB
invalidation is necessary when unmapping pages for reclaim. Although our
implementation is correct according to the architecture, returning true
only for valid, young ptes in the absence of racing page-table
modifications, this is in fact flawed due to lazy invalidation of old
ptes in ptep_clear_flush_young() where we elide the expensive DSB
instruction for completing the TLB invalidation.
Rather than penalise the aging path, adjust pte_accessible() to return
true for any valid pte, even if the access flag is cleared.
Cc: <stable@vger.kernel.org>
Fixes: 76c714be0e ("arm64: pgtable: implement pte_accessible()")
Reported-by: Yu Zhao <yuzhao@google.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201120143557.6715-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d19d2152ca ]
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5abb0132 ]
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9a8910b2 ]
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927f42fcc1 ]
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419c65f500 ]
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.
This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.
Fixes: 729e1ffcf4 ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a38c1c21 ]
Before the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd1 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e613ded8 ]
Commit ce3d31ad3c ("arm64/smp: Move rcu_cpu_starting() earlier") ensured
that RCU is informed early about incoming CPUs that might end up calling
into printk() before they are online. However, if such a CPU fails the
early CPU feature compatibility checks in check_local_cpu_capabilities(),
then it will be powered off or parked without informing RCU, leading to
an endless stream of stalls:
| rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
| rcu: 2-O...: (0 ticks this GP) idle=002/1/0x4000000000000000 softirq=0/0 fqs=2593
| (detected by 0, t=5252 jiffies, g=9317, q=136)
| Task dump for CPU 2:
| task:swapper/2 state:R running task stack: 0 pid: 0 ppid: 1 flags:0x00000028
| Call trace:
| ret_from_fork+0x0/0x30
Ensure that the dying CPU invokes rcu_report_dead() prior to being powered
off or parked.
Cc: Qian Cai <cai@redhat.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Suggested-by: Qian Cai <cai@redhat.com>
Link: https://lore.kernel.org/r/20201105222242.GA8842@willie-the-truck
Link: https://lore.kernel.org/r/20201106103602.9849-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 891deb8758 ]
cpu_psci_cpu_die() is called in the context of the dying CPU, which
will no longer be online or tracked by RCU. It is therefore not generally
safe to call printk() if the PSCI "cpu off" request fails, so remove the
pr_crit() invocation.
Cc: Qian Cai <cai@redhat.com>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20201106103602.9849-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f969f03888 ]
In a surprising turn of events, it transpires that CPU capabilities
configured as ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE are never set as the
result of late-onlining. Therefore our handling of erratum 1418040 does
not get activated if it is not required by any of the boot CPUs, even
though we allow late-onlining of an affected CPU.
In order to get things working again, replace the cpus_have_const_cap()
invocation with an explicit check for the current CPU using
this_cpu_has_cap().
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201106114952.10032-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f81cb2c3ad upstream.
ID registers are RAZ until they've been allocated a purpose, but
that doesn't mean they should be removed from the KVM_GET_REG_LIST
list. So far we only have one register, SYS_ID_AA64ZFR0_EL1, that
is hidden from userspace when its function, SVE, is not present.
Expose SYS_ID_AA64ZFR0_EL1 to userspace as RAZ when SVE is not
implemented. Removing the userspace visibility checks is enough
to reexpose it, as it will already return zero to userspace when
SVE is not present. The register already behaves as RAZ for the
guest when SVE is not present.
Fixes: 73433762fc ("KVM: arm64/sve: System register context switch and access support")
Reported-by: 张东旭 <xu910121@sina.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org#v5.2+
Link: https://lore.kernel.org/r/20201105091022.15373-2-drjones@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b64d814257 upstream.
Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.
Since commit a2c7023f70 ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.
Currently Espressobin DTS file contains alias just for ethernet0.
This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.
DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).
Fixes: 5253cb8c00 ("arm64: dts: marvell: espressobin: add ethernet alias")
Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported Espressobin rev V5 changes to 5.4 and 4.19 versions]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce3d31ad3c ]
The call to rcu_cpu_starting() in secondary_start_kernel() is not early
enough in the CPU-hotplug onlining process, which results in lockdep
splats as follows:
WARNING: suspicious RCU usage
-----------------------------
kernel/locking/lockdep.c:3497 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/1/0.
Call trace:
dump_backtrace+0x0/0x3c8
show_stack+0x14/0x60
dump_stack+0x14c/0x1c4
lockdep_rcu_suspicious+0x134/0x14c
__lock_acquire+0x1c30/0x2600
lock_acquire+0x274/0xc48
_raw_spin_lock+0xc8/0x140
vprintk_emit+0x90/0x3d0
vprintk_default+0x34/0x40
vprintk_func+0x378/0x590
printk+0xa8/0xd4
__cpuinfo_store_cpu+0x71c/0x868
cpuinfo_store_cpu+0x2c/0xc8
secondary_start_kernel+0x244/0x318
This is avoided by moving the call to rcu_cpu_starting up near the
beginning of the secondary_start_kernel() function.
Signed-off-by: Qian Cai <cai@redhat.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/lkml/160223032121.7002.1269740091547117869.tip-bot2@tip-bot2/
Link: https://lore.kernel.org/r/20201028182614.13655-1-cai@redhat.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1afbbb028 ]
This adds the missing perpheral clock for the RNG for Amlogic G12. As
stated in amlogic,meson-rng.yaml, this isn't always necessary for the
RNG to function, but is better to have in case the clock is disabled for
some reason prior to loading.
Signed-off-by: Scott K Logan <logans@cottsay.net>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/520a1a8ec7a958b3d918d89563ec7e93a4100a45.camel@cottsay.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ec9d78070d upstream.
Commit 39d114ddc6 ("arm64: add KASAN support") added .weak directives to
arch/arm64/lib/mem*.S instead of changing the existing SYM_FUNC_START_PI
macros. This can lead to the assembly snippet `.weak memcpy ... .globl
memcpy` which will produce a STB_WEAK memcpy with GNU as but STB_GLOBAL
memcpy with LLVM's integrated assembler before LLVM 12. LLVM 12 (since
https://reviews.llvm.org/D90108) will error on such an overridden symbol
binding.
Use the appropriate SYM_FUNC_START_WEAK_PI instead.
Fixes: 39d114ddc6 ("arm64: add KASAN support")
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201029181951.1866093-1-maskray@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Cc: Jian Cai <jiancai@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ac0f4526d upstream.
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the library code to the
new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: Use SYM_FUNC_START_WEAK_PI]
Signed-off-by: Will Deacon <will@kernel.org>
Cc: Jian Cai <jiancai@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35e61c77ef upstream.
As part of an effort to make the annotations in assembly code clearer and
more consistent new macros have been introduced, including replacements
for ENTRY() and ENDPROC().
On arm64 we have ENDPIPROC(), a custom version of ENDPROC() which is
used for code that will need to run in position independent environments
like EFI, it creates an alias for the function with the prefix __pi_ and
then emits the standard ENDPROC. Add new-style macros to replace this
which expand to the standard SYM_FUNC_*() and SYM_FUNC_ALIAS_*(),
resulting in the same object code. These are added in linkage.h for
consistency with where the generic assembler code has its macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: Rename 'WEAK' macro, use ';' instead of ASM_NL, deprecate ENDPIPROC]
Signed-off-by: Will Deacon <will@kernel.org>
Cc: Jian Cai <jiancai@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a1c2c7f63 upstream.
The DBGD{CCINT,SCRext} and DBGVCR register entries in the cp14 array
are missing their target register, resulting in all accesses being
targetted at the guard sysreg (indexed by __INVALID_SYSREG__).
Point the emulation code at the actual register entries.
Fixes: bdfb4b389c ("arm64: KVM: add trap handlers for AArch32 debug registers")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201029172409.2768336-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0fc70ce1f upstream.
Berlin SoCs always contain some DW APB timers which can be used as an
always-on broadcast timer.
Link: https://lore.kernel.org/r/20201009150536.214181fb@xhacker.debian
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a194c5f2d2 ]
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@tj.kylinos.cn>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Link: https://lore.kernel.org/r/20200921023936.21846-1-liuzhengyuan@tj.kylinos.cn
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3102bc0e6a ]
In the absence of ACPI or DT topology data, we fallback to haphazardly
decoding *something* out of MPIDR. Sadly, the contents of that register are
mostly unusable due to the implementation leniancy and things like Aff0
having to be capped to 15 (despite being encoded on 8 bits).
Consider a simple system with a single package of 32 cores, all under the
same LLC. We ought to be shoving them in the same core_sibling mask, but
MPIDR is going to look like:
| CPU | 0 | ... | 15 | 16 | ... | 31 |
|------+---+-----+----+----+-----+----+
| Aff0 | 0 | ... | 15 | 0 | ... | 15 |
| Aff1 | 0 | ... | 0 | 1 | ... | 1 |
| Aff2 | 0 | ... | 0 | 0 | ... | 0 |
Which will eventually yield
core_sibling(0-15) == 0-15
core_sibling(16-31) == 16-31
NUMA woes
=========
If we try to play games with this and set up NUMA boundaries within those
groups of 16 cores via e.g. QEMU:
# Node0: 0-9; Node1: 10-19
$ qemu-system-aarch64 <blah> \
-smp 20 -numa node,cpus=0-9,nodeid=0 -numa node,cpus=10-19,nodeid=1
The scheduler's MC domain (all CPUs with same LLC) is going to be built via
arch_topology.c::cpu_coregroup_mask()
In there we try to figure out a sensible mask out of the topology
information we have. In short, here we'll pick the smallest of NUMA or
core sibling mask.
node_mask(CPU9) == 0-9
core_sibling(CPU9) == 0-15
MC mask for CPU9 will thus be 0-9, not a problem.
node_mask(CPU10) == 10-19
core_sibling(CPU10) == 0-15
MC mask for CPU10 will thus be 10-19, not a problem.
node_mask(CPU16) == 10-19
core_sibling(CPU16) == 16-19
MC mask for CPU16 will thus be 16-19... Uh oh. CPUs 16-19 are in two
different unique MC spans, and the scheduler has no idea what to make of
that. That triggers the WARN_ON() added by commit
ccf74128d6 ("sched/topology: Assert non-NUMA topology masks don't (partially) overlap")
Fixing MPIDR-derived topology
=============================
We could try to come up with some cleverer scheme to figure out which of
the available masks to pick, but really if one of those masks resulted from
MPIDR then it should be discarded because it's bound to be bogus.
I was hoping to give MPIDR a chance for SMT, to figure out which threads are
in the same core using Aff1-3 as core ID, but Sudeep and Robin pointed out
to me that there are systems out there where *all* cores have non-zero
values in their higher affinity fields (e.g. RK3288 has "5" in all of its
cores' MPIDR.Aff1), which would expose a bogus core ID to userspace.
Stop using MPIDR for topology information. When no other source of topology
information is available, mark each CPU as its own core and its NUMA node
as its LLC domain.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20200829130016.26106-1-valentin.schneider@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b92fa7485 upstream.
With CONFIG_EXPERT=y, CONFIG_KASAN=y, CONFIG_RANDOMIZE_BASE=n,
CONFIG_RELOCATABLE=n, we observe the following failure when trying to
link the kernel image with LD=ld.lld:
error: section: .exit.data is not contiguous with other relro sections
ld.lld defaults to -z relro while ld.bfd defaults to -z norelro. This
was previously fixed, but only for CONFIG_RELOCATABLE=y.
Fixes: 3bbd3db864 ("arm64: relocatable: fix inconsistencies in linker script and options")
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201016175339.2429280-1-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ard Biesheuvel