[ Upstream commit 5f58591323 ]
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82ca4c922b ]
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8w9z
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.2.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 9f19306d16 ]
The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.
Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.
Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7241c5a697 ]
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58a ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAl9rJlYACgkQONu9yGCS
aT6WbRAAga6QVKrO6R4NeKk0fPqKQQoQeTK+phBOFA7jAoX/rIRKyob2Si9BwhBA
F77vZ6HIZ7+e/o35JJQYQbffbHYs0ANuS1oHGqe0vgbh+72Viaan6g7lFOhpx8qf
y0YS7q+hw4WLZB0gGlBM7nkPXRiis32IrEVabQW+t8hmT2lWyutY8E2yFAU60tvI
Tvjm2c2pvHEcHz9MrjEd/jIVxMFnIl42FBTx9bGsbDUCDzBwEvPArS4bNioP7EFJ
O+rrGCNvwtiv0DuKzX1UIZzQ88IROmU3ZjsIlgOwla7xJWv4QDgmPfyAyRI48QhH
PAZQmSntz+y+MP6B3z3ZBrxc2Fx0kCDtugn2P9+2RVUEpheANJ293vUgYTKN9Roy
dHdWHFWNTO9IYpIN0cZjc25db4ULdjerWQrKcCr6ZO8+Ep/0mSzx3lkWjfuUP8Hr
L2RD6rAm259OpPq8xhAcJpJvoQLwGxaBHyr4QYUmRgmNVURoqe9Q0MTZuiyGsXhm
rtcNky9WvmyyI1lJgXi4A+vmsIThCHEstEMycgTejfJ4itIVA9e1ctJVVomWULCn
9oNStBJpmHw0myDCohbKNjeO1UX/erdF9NaoGto5bnfIhcSae1YQEjRB8zKmzbg1
DpgC1f7IZ7q53vfrDGsAjInOcuEwAn/Y5JMLJOL4mdA9j3XlX2o=
=Ot99
-----END PGP SIGNATURE-----
Merge tag 'v5.4.67' into 5.4-2.2.x-imx
This is the 5.4.67 stable release
This updates the kernel present in the NXP release imx_5.4.47_2.2.0 to the
latest patchset available from stable korg.
Base stable kernel version present in the NXP BSP release is v5.4.47.
Following conflicts were recorded and resolved:
- arch/arm/mach-imx/pm-imx6.c
NXP version has a different PM vectoring scheme, where the IRAM bottom
half (8k) is used to store IRAM code and pm_info. Keep this version to
be compatible with NXP PM implementation.
- arch/arm64/boot/dts/freescale/imx8mm-evk.dts
- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
NXP patches kept to provide proper LDO setup:
imx8mm-evk.dts: 975d8ab07267ded741c4c5d7500e524c85ab40d3
imx8mn-ddr4-evk.dts: e8e35fd0e759965809f3dca5979a908a09286198
- drivers/crypto/caam/caamalg.c
Keep NXP version, as it already covers the functionality for the
upstream patch [d6bbd4eea2]
- drivers/gpu/drm/imx/dw_hdmi-imx.c
- drivers/gpu/drm/imx/imx-ldb.c
- drivers/gpu/drm/imx/ipuv3/ipuv3-crtc.c
Port changes from upstream commit [1a27987101], which extends
component lifetime by moving drm structures allocation/free from
bind() to probe().
- drivers/gpu/drm/imx/imx-ldb.c
Merge patch [1752ab50e8] from upstream to disable both LVDS channels
when Enoder is disabled
- drivers/mmc/host/sdhci-esdhc-imx.c
Fix merge fuzz produced by [6534c897fd].
- drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
Commit d1a00c9bb1 from upstream solves the issue with improper error
reporting when qdisc type support is absent. Upstream version is merged
into NXP implementation.
- drivers/net/ethernet/freescale/enetc/enetc.c
Commit [ce06fcb6a6] from upstream merged,
base NXP version kept
- drivers/net/ethernet/freescale/enetc/enetc_pf.c
Commit [e8b86b4d87] from upstream solves
the kernel panic in case if probing fails. NXP has a clean-up logic
implemented different, where the MDIO remove would be invoked in any
failure case. Keep the NXP logic in place.
- drivers/thermal/imx_thermal.c
Upstream patch [9025a5589c] adds missing
of_node_put call, NXP version has been adapted to accommodate this patch
into the code.
- drivers/usb/cdns3/ep0.c
Manual merge of commit [be8df02707] from
upstream to protect cdns3_check_new_setup
- drivers/xen/swiotlb-xen.c
Port upstream commit cca58a1669 to NXP tree, manual hunk was
resolved during merge.
- sound/soc/fsl/fsl_esai.c
Commit [53057bd4ac] upstream addresses the problem of endless isr in
case if exception interrupt is enabled and tasklet is scheduled. Since
NXP implementation has tasklet removed with commit [2bbe95fe6c],
upstream fix does not match the main implementation, hence we keep the
NXP version here.
- sound/soc/fsl/fsl_sai.c
Apply patch [b8ae2bf5cc] from upstream, which uses FIFO watermark
mask macro.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
commit 592d751c1e upstream.
If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df43dd526e upstream.
The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.
Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2fb6b6275 ]
For rx filter 'HWTSTAMP_FILTER_PTP_V2_EVENT', it should be
PTP v2/802.AS1, any layer, any kind of event packet, but HW only
take timestamp snapshot for below PTP message: sync, Pdelay_req,
Pdelay_resp.
Then it causes below issue when test E2E case:
ptp4l[2479.534]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.423]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.758]: port 1: received DELAY_REQ without timestamp
ptp4l[2483.524]: port 1: received DELAY_REQ without timestamp
ptp4l[2484.233]: port 1: received DELAY_REQ without timestamp
ptp4l[2485.750]: port 1: received DELAY_REQ without timestamp
ptp4l[2486.888]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.265]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.316]: port 1: received DELAY_REQ without timestamp
Timestamp snapshot dependency on register bits in received path:
SNAPTYPSEL TSMSTRENA TSEVNTENA PTP_Messages
01 x 0 SYNC, Follow_Up, Delay_Req,
Delay_Resp, Pdelay_Req, Pdelay_Resp,
Pdelay_Resp_Follow_Up
01 0 1 SYNC, Pdelay_Req, Pdelay_Resp
For dwmac v5.10a, enabling all events by setting register
DWC_EQOS_TIME_STAMPING[SNAPTYPSEL] to 2’b01, clearing bit [TSEVNTENA]
to 0’b0, which can support all required events.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a96ac8a004 ]
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 14b41a2959 ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.
Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized. Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce(). timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().
systemd--1995 2.... 552950018us : stmmac_suspend: 4994
ksoftirq-9 0..s2 553123133us : stmmac_tx_timer_arm: 2276
systemd--1995 0.... 553127896us : stmmac_resume: 5101
systemd--320 7...2 553132752us : stmmac_tx_timer_arm: 2276
(sd-exec-1999 5...2 553135204us : stmmac_tx_timer_arm: 2276
---------------------------------
pc : run_timer_softirq+0x468/0x5e0
lr : run_timer_softirq+0x570/0x5e0
Call trace:
run_timer_softirq+0x468/0x5e0
__do_softirq+0x124/0x398
irq_exit+0xd8/0xe0
__handle_domain_irq+0x6c/0xc0
gic_handle_irq+0x60/0xb0
el1_irq+0xb8/0x180
arch_cpu_idle+0x38/0x230
default_idle_call+0x24/0x3c
do_idle+0x1e0/0x2b8
cpu_startup_entry+0x28/0x48
secondary_start_kernel+0x1b4/0x208
Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Upstream commit f42234ffd5 ]
The paranoidal pointer check in IRQ handler looks very strange - it
really protects us only against bogus drivers which request IRQ line
with null pointer dev_id. However, the code fragment is incorrect
because the dev pointer is used before the actual check which leads
to undefined behavior. Remove the check to avoid confusing people
with incorrect code.
Signed-off-by: Maxim Petrov <mmrmaximuzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd4a517738 ]
Driver missed initializing num_por which is one of the por values that
driver configures to hardware. In order to get these values, add a new
structure ethqos_emac_driver_data which holds por and num_por values
and populate that in driver probe.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Reported-by: Rahul Ankushrao Kawadgave <rahulak@qti.qualcomm.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91a2559c1d ]
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ce30609d ]
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7a0d62696 ]
Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id"
but "rgmii-txid", "rgmii-rxid")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0212a5ebf ]
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 806fd188ce ]
After commit bfcb813203 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc191af1bb ]
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable runtime pm to shutdown the power domain when
netif status is down.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
[ Upstream commit 3e1221acf6 ]
Commit 9463c44559 ("net: stmmac: dwmac1000: Clear unused address
entries") cleared the unused mac address entries, but introduced an
out-of bounds mac address register programming bug -- After setting
the secondary unicast mac addresses, the "reg" value has reached
netdev_uc_count() + 1, thus we should only clear address entries
if (addr < perfect_addr_number)
Fixes: 9463c44559 ("net: stmmac: dwmac1000: Clear unused address entries")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9de9aa487d ]
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b723bd9339 ]
ACS (auto PAD/FCS stripping) removes FCS off 802.3 packets (LLC) so that
there is no need to manually strip it for such packets. The enhanced DMA
descriptors allow to flag LLC packets so that the receiving callback can
use that to strip FCS manually or not. On the other hand, normal
descriptors do not support that.
Thus in order to not truncate LLC packet ACS should be disabled when
using normal DMA descriptors.
Fixes: 47dd7a540b ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 474a31e13a ]
We cannot register the same netdev notifier multiple times when probing
stmmac devices. Register the notifier only once in module init, and also
make debugfs creation/deletion safe against simultaneous notifier call.
Fixes: 481a7d154c ("stmmac: debugfs entry name is not be changed when udev rename device name.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
mdio bus reset should not happen during resume back for
most of phys, so let mdio bus reset is decided by dts.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Start phylink instance and resume back the PHY to supply
RX clock to MAC before MAC layer initialization by calling
.stmmac_hw_setup(), since DMA reset depends on the RX clock,
otherwise DMA reset cost maximum timeout value then finally
timeout.
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Frame preemption could not disabled and is always set when set qbv.
After FPE is disabled, return the function to avoid this.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
[ Upstream commit 7d10f0774f ]
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14b41a2959 ]
When running v5.5 with a rootfs on NFS, memory abort may happen in
the system resume stage:
Unable to handle kernel paging request at virtual address dead00000000012a
[dead00000000012a] address between user and kernel address ranges
pc : run_timer_softirq+0x334/0x3d8
lr : run_timer_softirq+0x244/0x3d8
x1 : ffff800011cafe80 x0 : dead000000000122
Call trace:
run_timer_softirq+0x334/0x3d8
efi_header_end+0x114/0x234
irq_exit+0xd0/0xd8
__handle_domain_irq+0x60/0xb0
gic_handle_irq+0x58/0xa8
el1_irq+0xb8/0x180
arch_cpu_idle+0x10/0x18
do_idle+0x1d8/0x2b0
cpu_startup_entry+0x24/0x40
secondary_start_kernel+0x1b4/0x208
Code: f9000693 a9400660 f9000020 b4000040 (f9000401)
---[ end trace bb83ceeb4c482071 ]---
Kernel panic - not syncing: Fatal exception in interrupt
SMP: stopping secondary CPUs
SMP: failed to stop secondary CPUs 2-3
Kernel Offset: disabled
CPU features: 0x00002,2300aa30
Memory Limit: none
---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
It's found that stmmac_xmit() and stmmac_resume() sometimes might
run concurrently, possibly resulting in a race condition between
mod_timer() and setup_timer(), being called by stmmac_xmit() and
stmmac_resume() respectively.
Since the resume() runs setup_timer() every time, it'd be safer to
have del_timer_sync() in the suspend() as the counterpart.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 481a7d154c ]
Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7bd754c47d upstream.
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e715d74504 upstream.
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d39b68e5a7 upstream.
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e1838200 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b9f932edc upstream.
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f3a481c4 upstream.
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8605131747 upstream.
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52cc73e540 ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Zhizhikin