[ Upstream commit b9b7fb2943 ]
On page 23 of the datasheet [0] it says "The register remains unchanged
until the interrupt is cleared via a read of INTCAP or GPIO." Include
INTCAPA and INTCAPB registers in precious range, so that they aren't
accidentally cleared when we read via debugfs.
[0] https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-3-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b445f62377 ]
The mcp23x17_regmap is initialised with structs named "mcp23x16".
However, the mcp23s08 driver doesn't support the MCP23016 device yet, so
this appears to be a typo.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-2-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513034d8b0 ]
When PINCTRL_BCM2835 is enabled and GPIOLIB is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_BCM2835 [=y] && PINCTRL [=y] && OF [=y] && (ARCH_BCM2835 [=n] || ARCH_BRCMSTB [=n] || COMPILE_TEST [=y])
The reason is that PINCTRL_BCM2835 selects GPIOLIB_IRQCHIP without
depending on or selecting GPIOLIB while GPIOLIB_IRQCHIP is subordinate to
GPIOLIB.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200914144025.371370-1-fazilyildiran@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63c3212e7a ]
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 84e7a946da upstream.
The PAT1 register contains information about the IRQ type (edge/level)
for input GPIOs with IRQ enabled, and the direction for non-IRQ GPIOs.
So it makes sense to read it only if the GPIO has no interrupt
configured, otherwise input GPIOs configured for level IRQs are
misdetected as output GPIOs.
Fixes: ebd6651418 ("pinctrl: ingenic: Implement .get_direction for GPIO chips")
Reported-by: João Henrique <johnnyonflame@hotmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200622214548.265417-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c95348ba3 upstream.
Ingenic SoCs don't natively support registering an interrupt for both
rising and falling edges. This has to be emulated in software.
Until now, this was emulated by switching back and forth between
IRQ_TYPE_EDGE_RISING and IRQ_TYPE_EDGE_FALLING according to the level of
the GPIO. While this worked most of the time, when used with GPIOs that
need debouncing, some events would be lost. For instance, between the
time a falling-edge interrupt happens and the interrupt handler
configures the hardware for rising-edge, the level of the pin may have
already risen, and the rising-edge event is lost.
To address that issue, instead of switching back and forth between
IRQ_TYPE_EDGE_RISING and IRQ_TYPE_EDGE_FALLING, we now switch back and
forth between IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_LEVEL_HIGH. Since we
always switch in the interrupt handler, they actually permit to detect
level changes. In the example above, if the pin level rises before
switching the IRQ type from IRQ_TYPE_LEVEL_LOW to IRQ_TYPE_LEVEL_HIGH,
a new interrupt will raise as soon as the handler exits, and the
rising-edge event will be properly detected.
Fixes: e72394e2ea ("pinctrl: ingenic: Merge GPIO functionality")
Reported-by: João Henrique <johnnyonflame@hotmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: João Henrique <johnnyonflame@hotmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200622214548.265417-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f46fe79ff1 ]
This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no
pinctrl_map is added. The current behavior is to return 0 when
!PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry()
incorrectly assumes that a map was added and sets num_maps = 2.
Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf()
if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf()
returns 0 to indicate there was no error and num_maps is then set to 2:
980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
981 struct device_node *np,
982 struct pinctrl_map **map,
983 unsigned *num_maps,
984 const char **pgnames)
985 {
<snip>
1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054 (*map)->data.mux.group = np->name;
1055 (*map)->data.mux.function = np->name;
1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }
However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or
!nconfs. I believe these conditions should indicate that no map was
added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry()
will set num_maps = 2 even though no maps were successfully added, as
it does not reach "m++" on line 940:
895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;
938 func->nconfs = nconfs;
939 conf = &(func->conf[0]);
940 m++;
This situtation will cause a boot failure [0] on the BeagleBone Black
(AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi
has compatible = "pinconf-single" instead of "pinctrl-single".
The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF
or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no
map was added.
Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish
between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps
is set to 1 as it is valid for pinconf to be enabled and a given pin
group to not any pinconf properties.
[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/
Fixes: 9dddb4df90 ("pinctrl: single: support generic pinconf")
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69339d083d ]
uart0_pins is defined as:
static const unsigned uart0_pins[] = {135, 136, 137, 138, 139};
which npins is wronly specified as 9 later
{
.name = "uart0",
.pins = uart0_pins,
.npins = 9,
},
npins should be 5 instead of 9 according to the definition.
Signed-off-by: Jacky Hu <hengqing.hu@gmail.com>
Link: https://lore.kernel.org/r/20200616015024.287683-1-hengqing.hu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 782b6b6984 ]
Use noirq suspend/resume callbacks as other drivers which implement
noirq suspend/resume callbacks (Ex:- PCIe) depend on pinctrl driver to
configure the signals used by their respective devices in the noirq phase.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200604174935.26560-1-vidyas@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e50311556 ]
Fix the following warnings caused by reusage of the same irq_chip
instance for all spmi-gpio gpio_irq_chip instances. Instead embed
irq_chip into pmic_gpio_state struct.
gpio gpiochip2: (c440000.qcom,spmi:pmic@2:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip3: (c440000.qcom,spmi:pmic@4:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip4: (c440000.qcom,spmi:pmic@a:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200604002817.667160-1-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d8da5cab ]
'pinctrl_unregister()' should not be called to undo
'devm_pinctrl_register_and_init()', it is already handled by the framework.
This simplifies the error handling paths of the probe function.
The 'imx_free_resources()' can be removed as well.
Fixes: a51c158bf0 ("pinctrl: imx: use radix trees for groups and functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20200530204955.588962-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eb7283212 ]
When 'pinctrl_register()' has been turned into 'devm_pinctrl_register()',
an error handling path has not been updated.
Axe a now unneeded 'pinctrl_unregister()'.
Fixes: e55e025d16 ("pinctrl: imxl: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200530201952.585798-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7faa8ffb6 ]
In function rockchip_dt_node_to_map, a new_map variable is
allocated by:
new_map = devm_kcalloc(pctldev->dev, map_num, sizeof(*new_map),
GFP_KERNEL);
This uses devres and attaches new_map to the pinctrl driver.
This cause a leak since new_map is not released when the probed
driver is removed. Fix it by using kcalloc to allocate new_map
and free it in `rockchip_dt_free_map`
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200506100903.15420-1-dafna.hirschfeld@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b4e8e93ec ]
The rza1l_swio_entries referred to the wrong array rza1h_swio_pins,
which was intended to be rza1l_swio_pins. So let's fix it.
This is detected by the following gcc warning:
drivers/pinctrl/pinctrl-rza1.c:401:35: warning: ‘rza1l_swio_pins’
defined but not used [-Wunused-const-variable=]
static const struct rza1_swio_pin rza1l_swio_pins[] = {
^~~~~~~~~~~~~~~
Fixes: 039bc58e73 ("pinctrl: rza1: Add support for RZ/A1L")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200417111604.19143-1-yanaijie@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b47afc654 ]
This fixes a problem with using the GPIO as an interrupt on Jaguar2
(and similar), as the register layout of the platforms with 64 GPIO's
are pairwise, such that the original offset must be multiplied with
the platform stride.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-4-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f354157a7d upstream.
Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers
are saved and restored over a suspend/resume cycle. However, the
EINT_MASK registers are not.
On S5PV210 at the very least, these registers are not retained over
suspend, leading to the interrupts remaining masked upon resume and
therefore no interrupts being triggered for the device. There should
be no effect on any SoCs that do retain these registers as theoretically
we would just be re-writing what was already there.
Fixes: 7ccbc60cd9 ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b577a27991 upstream.
Commit a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt
mask") started writing the eint wakeup mask from the pinctrl driver.
Unfortunately, it made the assumption that the private retention data
was always a regmap while in the case of s5pv210 it is a raw pointer
to the clock base (as the eint wakeup mask not in the PMU as with newer
Exynos platforms).
Fixes: a8be2af021 ("pinctrl: samsung: Write external wakeup interrupt mask")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69388e15f5 ]
According to Braswell NDA Specification Update (#557593),
concurrent read accesses may result in returning 0xffffffff and write
instructions may be dropped. We have an established format for the
commit references, i.e.
cdca06e4e8 ("pinctrl: baytrail: Add missing spinlock usage in
byt_gpio_irq_handler")
Fixes: 0bd50d719b ("pinctrl: cherryview: prevent concurrent access to GPIO controllers")
Signed-off-by: Grace Kao <grace.kao@intel.com>
Reported-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90bcb0c3ca ]
Fix a typo in the readl/writel accessor conversion where val is used
instead of pol changing the behavior of the original code.
Cc: stable@vger.kernel.org
Fixes: 6c73698904 pinctrl: qcom: Introduce readl/writel accessors
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200414003726.25347-1-ansuelsmth@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccd025eadd ]
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Baytrail.
Fixes: c501d0b149 ("pinctrl: baytrail: Add pin control operations")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b7275c877 ]
It appears that SPT-H variant has different offset for PAD locking registers.
Fix it here.
Fixes: 551fa5801e ("pinctrl: intel: sunrisepoint: Add Intel Sunrisepoint-H support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aafd56fc79 upstream.
kref_init starts with the reference count at 1, which will be balanced
by the pinctrl_put in pinctrl_unregister. The additional kref_get in
pinctrl_claim_hogs will increase this count to 2 and cause the hogs to
not get freed when pinctrl_unregister is called.
Fixes: 6118714275 ("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228154142.13860-1-ckeepax@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c48e549f3 upstream.
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/bd7ad5fd755739a6d8d5f4f65e03b3ca4f457bd2.1582216144.git.leonard.crestez@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7a06b0db upstream.
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02aeb2f215 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23680594d ]
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b1cb1f03 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 805f635703 upstream.
The FN_SDSELF_B and FN_SD1_CLK_B enum IDs are used twice, which means
one set of users must be wrong. Replace them by the correct enum IDs.
Fixes: 87f8c98863 ("sh-pfc: Add r8a7778 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-2-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a34cd9dfd0 upstream.
R-Car Gen3 Hardware Manual Errata for Rev. 2.00 of October 24, 2019
changed the configuration bits for drive and bias control for the
DU_DOTCLKIN3 pin on R-Car M3-N, to match the same pin on R-Car H3.
Update the driver to reflect this.
After this, the handling of drive and bias control for the various
DU_DOTCLKINx pins is consistent across all of the R-Car H3, M3-W,
M3-W+, and M3-N SoCs.
Fixes: 86c045c2e4 ("pinctrl: sh-pfc: r8a77965: Replace DU_DOTCLKIN2 by DU_DOTCLKIN3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191113101653.28428-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9608ea6c66 upstream.
Commit 179e5a6114 ("pinctrl: intel: Remove default Interrupt Status
offset") removes default interrupt status offset of GPIO controllers,
with previous commits explicitly providing the previously default
offsets. However, the is_offset value in SPTH_COMMUNITY is missing,
preventing related irq from being properly detected and handled.
Fixes: f702e0b93c ("pinctrl: sunrisepoint: Provide Interrupt Status register offset")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205745
Cc: stable@vger.kernel.org
Signed-off-by: Boyan Ding <boyan.j.ding@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e66ff71fd0 upstream.
Version 1.1v6 of pin list has some changes in pin names for Intel Lewisburg.
Update the driver accordingly.
Note, it reveals the bug in the driver that misses two pins in GPP_L and
has rather two extra ones. That's why the ordering of some groups is changed.
Fixes: e480b74538 ("pinctrl: intel: Add Intel Lewisburg GPIO support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191120133739.54332-1-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad7fe1a1a3 upstream.
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191016142601.28255-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d30710b8cc upstream.
This patch allows PINMUX_IPSR_PHYS() to set bits in GPSR.
When assigning function to pin, GPSR should be set to peripheral
function.
For example when using SCL3, GPSR2 bit7 (PWM1_A pin) should be set to
peripheral function.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Link: https://lore.kernel.org/r/20191008060112.29819-1-nobuta.keiya@fujitsu.com
Fixes: 50d1ba1764 ("pinctrl: sh-pfc: Add physical pin multiplexing helper macros")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ff8aca906 upstream.
The call to pinctrl_count_index_with_args checks for a -EINVAL return
however this function calls pinctrl_get_list_and_count and this can
return -ENOENT. Rather than check for a specific error, fix this by
checking for any error return to catch the -ENOENT case.
Addresses-Coverity: ("Improper use of negative")
Fixes: 003910ebc8 ("pinctrl: Introduce TI IOdelay configuration driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190920122030.14340-1-colin.king@canonical.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35c60be220 upstream.
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7e36e1894 upstream.
In a rare randconfig build I came across one configuration that does
not enable CONFIG_GPIOLIB, which is needed by lochnagar:
ERROR: "devm_gpiochip_add_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_free" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_request" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_get_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
Add another 'select' like all other pinctrl drivers have.
Fixes: 0548448b71 ("pinctrl: lochnagar: Add support for the Cirrus Logic Lochnagar")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191218163701.171914-1-arnd@arndb.de
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ba2fd391a ]
This commit adds a check on ops pointer to avoid a kernel panic when
ops->strict is used. Indeed, on some pinctrl driver (at least for
pinctrl-stmfx) the pinmux ops is not implemented. Let's assume than gpio
can be used in this case.
Fixes: 472a61e777 ("pinctrl/gpio: Take MUX usage into account")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20191204144106.10876-1-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb45f2110b ]
Early revisions of the AST2600 datasheet are conflicted about the state
of the LPC/eSPI strapping bit (SCU510[6]). Conversations with ASPEED
determined that the reference pinmux configuration tables were in error
and the SCU documentation contained the correct configuration. Update
the driver to reflect the state described in the SCU documentation.
Fixes: 2eda1cdec4 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202050110.15340-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 40ecab5512 upstream.
Commit 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81898a44f2 ]
The SDC_QDSD_PINGROUP/UFS_RESET macros are missing the .tile info needed to
calculate the right register offsets. Adding them here and also
adjusting the offsets accordingly.
Fixes: f2ae04c45b ("pinctrl: qcom: Add SC7180 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/20191021141507.24066-1-rnayak@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884caadad1 ]
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4c60b563 ]
When populating the pinctrl mapping table entries for a device, the
'dev_name' field for each entry is initialised to point directly at the
string returned by 'dev_name()' for the device and subsequently used by
'create_pinctrl()' when looking up the mappings for the device being
probed.
This is unreliable in the presence of calls to 'dev_set_name()', which may
reallocate the device name string leaving the pinctrl mappings with a
dangling reference. This then leads to a use-after-free every time the
name is dereferenced by a device probe:
| BUG: KASAN: invalid-access in strcmp+0x20/0x64
| Read of size 1 at addr 13ffffc153494b00 by task modprobe/590
| Pointer tag: [13], memory tag: [fe]
|
| Call trace:
| __kasan_report+0x16c/0x1dc
| kasan_report+0x10/0x18
| check_memory_region
| __hwasan_load1_noabort+0x4c/0x54
| strcmp+0x20/0x64
| create_pinctrl+0x18c/0x7f4
| pinctrl_get+0x90/0x114
| devm_pinctrl_get+0x44/0x98
| pinctrl_bind_pins+0x5c/0x450
| really_probe+0x1c8/0x9a4
| driver_probe_device+0x120/0x1d8
Follow the example of sysfs, and duplicate the device name string before
stashing it away in the pinctrl mapping entries.
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Elena Petrova <lenaptr@google.com>
Tested-by: Elena Petrova <lenaptr@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191002124206.22928-1-will@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7666dfd533 ]
This reverts commit e167d723e1.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SIMCARD_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3672bc7093 ]
This reverts commit e87882eb9b.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SSI2_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7f028caadf upstream.
In s3c64xx_eint_eint0_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 61dd726131 ("pinctrl: Add pinctrl-s3c64xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a322b3377f upstream.
Several functions use for_each_child_of_node() loop with a break to find
a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 9a2c1c3b91 ("pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fbbcb0508 upstream.
In s3c24xx_eint_init() the for_each_child_of_node() loop is used with a
break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: af99a75074 ("pinctrl: Add pinctrl-s3c24xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c7f48dd14 upstream.
In exynos_eint_wkup_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 43b169db18 ("pinctrl: add exynos4210 specific extensions for samsung pinctrl driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Preston