[ Upstream commit 3d07c3b3a8 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: ed5e8f6891 ("arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/12506964ca5d5f936579a280ad0a7e7f9a0a2d4c.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c183c406c4 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240 ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c605e00c ]
The max frequency for the w25q32 (VIM v1.2) and w25q128 (VIM v1.4) spifc
chip should be 104Mhz not 30MHz.
Fixes: b8b74dda39 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125024001.19036-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee2078 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0570a575a ]
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e2 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4076a007bd ]
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa669a994 ]
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b26c1a034 ]
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c30 ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53e573dc39 ]
The CAT875 sub board from Silicon Linux uses Realtek phy and the driver
does not support rxc-skew-ps property.
Fixes: 6b170cd3ed ("arm64: dts: renesas: cat875: Add ethernet support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201015132350.8360-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb31949693 ]
Commit ff4c371d2b ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2013a4b684 ]
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0011c6d182 ]
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
[1]
https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201104162356.1251-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=CUC6
-----END PGP SIGNATURE-----
Merge tag 'v5.4.81' into 5.4-2.2.x-imx
This is the 5.4.81 stable release
Conflicts (manual resolve):
- drivers/tee/optee/call.c:
Drop commit e0238fcd9f ("MLK-21698: tee:optee: fix shared memory
page attribute checks") from NXP in favor of 0e467f6af99f ("optee:
add writeback to valid memory type") from upstream as including the
WT-marked memory blocks is not compatible with OP-TEE design.
Link: https://lore.kernel.org/lkml/AM6PR06MB4691D4988AC57DD24424D40CA6F30@AM6PR06MB4691.eurprd06.prod.outlook.com/
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 1741e18737 ]
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d2152ca ]
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5abb0132 ]
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9a8910b2 ]
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927f42fcc1 ]
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f4428867 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419c65f500 ]
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.
This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.
Fixes: 729e1ffcf4 ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a38c1c21 ]
Before the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd1 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b64d814257 upstream.
Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.
Since commit a2c7023f70 ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.
Currently Espressobin DTS file contains alias just for ethernet0.
This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.
DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).
Fixes: 5253cb8c00 ("arm64: dts: marvell: espressobin: add ethernet alias")
Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported Espressobin rev V5 changes to 5.4 and 4.19 versions]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1afbbb028 ]
This adds the missing perpheral clock for the RNG for Amlogic G12. As
stated in amlogic,meson-rng.yaml, this isn't always necessary for the
RNG to function, but is better to have in case the clock is disabled for
some reason prior to loading.
Signed-off-by: Scott K Logan <logans@cottsay.net>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/520a1a8ec7a958b3d918d89563ec7e93a4100a45.camel@cottsay.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fZ3T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8w9z
-----END PGP SIGNATURE-----
Merge tag 'v5.4.73' into 5.4-2.2.x-imx
This is the 5.4.73 stable release
Conflicts:
- arch/arm/boot/dts/imx6sl.dtsi:
Commit [a1767c9019] in NXP tree is now covered with commit [5c4c2f437c]
from upstream.
- drivers/gpu/drm/mxsfb/mxsfb_drv.c:
Resolve merge hunk for patch [ed8b90d303] from upstream
- drivers/media/i2c/ov5640.c:
Patch [aa4bb8b883] in NXP tree is now covered by patches [79ec0578c7]
and [b2f8546056] from upstream. Changes from NXP patch [99aa4c8c18] are
covered in upstream version as well.
- drivers/net/ethernet/freescale/fec_main.c:
Fix merge fuzz for patch [9e70485b40] from upstream.
- drivers/usb/cdns3/gadget.c:
Keep NXP version of the file, upstream version is not compatible.
- drivers/usb/dwc3/core.c:
- drivers/usb/dwc3/core.h:
Fix merge fuzz of patch [08045050c6] together wth NXP patch [b30e41dc1e]
- sound/soc/fsl/fsl_sai.c:
- sound/soc/fsl/fsl_sai.h:
Commit [2ea70e51eb72a] in NXP tree is now covered with commit [1ad7f52fe6]
from upstream.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 35292518cb ]
DT binding permits only one compatible string which was decribed in past by
commit 63cab195bf ("i2c: removed work arounds in i2c driver for Zynq
Ultrascale+ MPSoC").
The commit aea37006e1 ("dt-bindings: i2c: cadence: Migrate i2c-cadence
documentation to YAML") has converted binding to yaml and the following
issues is reported:
...: i2c@ff030000: compatible: Additional items are not allowed
('cdns,i2c-r1p10' was unexpected)
From schema:
.../Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml fds
...: i2c@ff030000: compatible: ['cdns,i2c-r1p14', 'cdns,i2c-r1p10'] is too
long
The commit c415f9e830 ("ARM64: zynqmp: Fix i2c node's compatible string")
has added the second compatible string but without removing origin one.
The patch is only keeping one compatible string "cdns,i2c-r1p14".
Fixes: c415f9e830 ("ARM64: zynqmp: Fix i2c node's compatible string")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/cc294ae1a79ef845af6809ddb4049f0c0f5bb87a.1598259551.git.michal.simek@xilinx.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb1eb3cd4 ]
After commit 7cdf8446ed ("arm64: dts: actions: Add pinctrl node for
Actions Semi S700") following error has been observed while booting
Linux on Cubieboard7-lite(based on S700 SoC).
[ 0.257415] pinctrl-s700 e01b0000.pinctrl: can't request region for
resource [mem 0xe01b0000-0xe01b0fff]
[ 0.266902] pinctrl-s700: probe of e01b0000.pinctrl failed with error -16
This is due to the fact that memory range for "sps" power domain controller
clashes with pinctrl.
One way to fix it, is to limit pinctrl address range which is safe
to do as current pinctrl driver uses address range only up to 0x100.
This commit limits the pinctrl address range to 0x100 so that it doesn't
conflict with sps range.
Fixes: 7cdf8446ed ("arm64: dts: actions: Add pinctrl node for Actions
Semi S700")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c91dfc9818 ]
According to Technical Update TN-RCT-S0352A/E, MSIOF1 DMA can only be
used with SYS-DMAC0 on R-Car E3.
Fixes: 62c0056f1c ("arm64: dts: renesas: r8a774c0: Add MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200917132117.8515-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 453802c463 ]
According to Technical Update TN-RCT-S0352A/E, MSIOF1 DMA can only be
used with SYS-DMAC0 on R-Car E3.
Fixes: 8517042060 ("arm64: dts: renesas: r8a77990: Add DMA properties to MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200917132117.8515-2-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 027cca9eb5 ]
The mdss node sets #interrupt-cells = <1>, so its interrupts
should be referenced using a single cell (in this case: only the
interrupt number).
However, right now the mdp/dsi node both have two interrupt cells
set, e.g. interrupts = <4 0>. The 0 is probably meant to say
IRQ_TYPE_NONE (= 0), but with #interrupt-cells = <1> this is
actually interpreted as a second interrupt line.
Remove the IRQ flags from both interrupts to fix this.
Fixes: 305410ffd1 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f0cbb57d ]
Tha parent node of "wcd_codec" specifies #address-cells = <1>
and #size-cells = <0>, which means that each resource should be
described by one cell for the address and size omitted.
However, wcd_codec currently lists 0x200 as second cell (probably
the size of the resource). When parsing this would be treated like
another memory resource - which is entirely wrong.
To quote the device tree specification [1]:
"If the parent node specifies a value of 0 for #size-cells,
the length field in the value of reg shall be omitted."
[1]: https://www.devicetree.org/specifications/
Fixes: 5582fcb382 ("arm64: dts: apq8016-sbc: add analog audio support with multicodec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6859ae860 ]
Commit fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
removed the unit names for most of the thermal trip points defined
in msm8916.dtsi, but missed to update the one for cpu0_1-thermal.
So why wasn't this spotted by "make dtbs_check"? Apparently, the name
of the thermal zone is already invalid: thermal-zones.yaml specifies
a regex of ^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$, so it is not allowed
to contain underscores. Therefore the thermal zone was never verified
using the DTB schema.
After replacing the underscore in the thermal zone name, the warning
shows up:
apq8016-sbc.dt.yaml: thermal-zones: cpu0-1-thermal:trips: 'trip-point@0'
does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Fix up the thermal zone names and remove the unit name for the trip point.
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: fe2aff0c57 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791619f668 ]
The i.MX General Power Controller v2 device node was missing interrupts
property necessary to route its interrupt to GIC. This also fixes the
dbts_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000:
{'compatible': ... '$nodename': ['gpc@303a0000']} is not valid under any of the given schemas
arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000: 'interrupts' is a required property
Fixes: fdbcc04da2 ("arm64: dts: imx8mq: add GPC power domains")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2933bf3528 ]
H5's Mali GPU PMU is not present or working corretly although
H5 datasheet record its interrupt vector.
Adding this module will miss lead lima driver try to shutdown
it and get waiting timeout. This problem is not exposed before
lima runtime PM support is added.
Fixes: bb39ed07e5 ("arm64: dts: allwinner: h5: Add device node for Mali-450 GPU")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200822062755.534761-1-yuq825@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f9d87d08e ]
The LEDs on the vim3 are active when the gpio is high, not low.
Fixes: c6d29c66e5 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200803141850.172704-1-jbrunet@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 12fa1078ef)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Andrey Zhizhikin