Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Definition of VLV RR switch bit and corresponding toggling in
set_drrs function.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When one EU is disabled in a particular subslice, we can tune how the
work is spread between subslices to improve EU utilization.
v2: - Use a bitfield to record which subslice(s) has(have) 7 EUs. That
will also make the machinery work if several sublices have 7 EUs.
(Jeff Mcgee)
- Only apply the different hashing algorithm if the slice is
effectively unbalanced by checking there's a single subslice with
7 EUs. (Jeff Mcgee)
v3: Fix typo in comment (Jeff Mcgee)
Issue: VIZ-3845
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Reviewed-by: Jeff Mcgee <jeff.mcgee@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen9 the render power gating can leave slice/subslice/EU in
a partially enabled state. We must make an explicit request for
full SSEU enablement through the Render Power Clock State
register when resuming render work. This register is save/
restored in the logical ring context image for execlist
submission mode. Initialize its value in each LRC image to
request full enablement according to the device SSEU config.
Thanks to Sharma Ankitprasad and Akash Goel for highlighting the
issue and proposing the initial fix on which this patch is based.
v2: Adjusted the names of the power gating support flags to fit
update of an earlier patch.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: "Akash Goel <akash.goel@intel.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new section to the 'i915_sseu_status' debugfs entry to
report the currently enabled counts of slice, subslice, and
execution units on the device. The count of enabled subslice
per slice represents the most enabled subslice on any one
slice for devices where imbalances may exist. Similarly, the
count of enabled EU per subslice represents the most enabled
EU on any one subslice.
Collect this device status for Skylake by reading the Gen9
power gate control ack message registers. Power gate control
operates on EU in pairs, therefore our reported counts of
enabled EU can be overestimated by one for each pair in which
one EU is fused-off.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read fuse registers to determine the available slice total,
subslice total, subslice per slice, EU total, and EU per subslice
counts of the SKL device. The EU per subslice attribute is more
precisely defined as the maximum EU available on any one subslice,
since available EU counts may vary across subslices due to fusing.
Set flags indicating the SKL device's slice/subslice/EU (SSEU)
power gating capability. Make all values available via debugfs
entry 'i915_sseu_status'.
v2: Several small clean-ups suggested by Damien. Most notably,
used smaller types for the new device info fields to reduce
memory usage and improved the clarity/readability of the
method used to extract attribute values from the fuse
registers.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added new PHY register definitions to control TDC buffer calibration and
digital lock threshold.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This W/A is put in a gen9 specific function because it may well be
needed on other gen9 platforms.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's also take the opportunity the remove the comment telling it's a
pre-prod W/A, it should be obvious from the stepping test.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we compare the whole EDRAM_PRESENT/EDRAMCAP register value
to 1 while EDRAM_PRESENT is only bit 0 (the rest may be used to describe
eDRAM capabilities).
To be more future proof, only look at bit 0 to detect eDRAM presence.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This one doesn't have one of these nice cryptic names unfortunately.
v2: Added missing register bitmap
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements core logic of SKL display power well.
v2: Addressed Imre's comments
- Added respective DDIs under power well #1 and #2
- Simplified repetitive code in power well programming
v3: Implemented Imre's comments
- Further simplified power well programming
- Made sure that PW 1 is enabled prior to PW 2
v4: Fix minor conflict with the the cherryview support (Damien)
v5: Add the PLL power domain to the always on power well (Damien)
v6: Disable BIOS power well (Imre)
Use power well data for comparison (Imre)
Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh,
Damien)
v7: Addressed Imre's comments
- Lowered the time out to 1ms
- Added parantheses in macro
- Moved debug message and fixed wait_for interval
v8:
- Add a WARN() when swiching on an unknown power well (Imre, done by Damien)
- Whitespace fixes (spaces instead of tabs) (Damien)
v9: (Imre, done by Damien)
- Merge the register definitions with this patch
- Merge the MISC IO power well in this patch
v10: (Imre, done by Damien)
- Define the Misc I/O power domains to be the power well 1 ones as Misc I/O
needs to be enabled with PW1
- Added Transcoder A and VGA domains to PW 2
- Remove the MISC_IO power domains as well in the the always on
domains definition
- Move Misc I/O power well at the top of the power well list so it's turned
on right after PW1.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.
v2: introduce EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable coarse power gating for Gen9. This feature allows render and
media engine to enter RC6 independently. Policies are configured
together with RC6. This feature will only be enabled when RC6 is
enabled.
v2: Rebase after Chris'/Mika's forcewake change (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.
v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)
v3: add break in switch conditions (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Cherryview, devices may have a varying number of EU for
a given ID due to creative fusing. Punit support different frequency for
different fuse data. We use this patch to help get total eu enabled and
read the right offset to get RP0
Based upon a patch from Jeff, but reworked to only store eu_total and
avoid sending info to userspace
v2: Format register definitions (Jani)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found by reading the HIZ_CHICKEN documentation.
Improves performance in a HiZ microbenchmark by around 50%.
Improves performance in OglZBuffer by around 18%.
Thanks to Chris Wilson for helping me figure out where to put this.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Haswell significantly improved the performance of sampler_c messages,
but the optimization appears to be off by default. Later platforms
remove this bit, and apparently always enable the optimization.
Improves performance in "Counter Strike: Global Offensive" by 18%
at default settings on Iris Pro.
This may break sampling of paletted formats (P8/A8P8/P8A8). It's
unclear whether it affects sampling of paletted formats in general,
or just the sample_c message (which is never used).
While libva does have support for using paletted formats (primarily
for OSDs), that support appears to have been broken for at least a
year, so I couldn't observe a regression from this:
I tried to get libva-intel to use paletted formats, and observe a
regression...but the only thing I found that used it was mplayer's OSD
(on screen display). Even without my patch, the colors were totally
wrong with that, and it's according to a few distro wikis, that's been
the case for over a year.
If libva's code for paletted formats /is/ broken, they could always
add code to disable this bit using the command validator when fixing
it.
Further investigation from Haihao shows that libva mplayer OSD seems
to work at least on his setup (still unclear what's wron with Ken's),
and that it's not affected by this patch. Quoting the discussion
between Haihao and Ken:
> > > If you use "-vo gl" or "-vo xv", the OSD is solid white text with a black
> > > border around it. I presume that it's supposed to be white with vaapi as
> > > well, but I guess I'm not entirely sure.
> > >
> > > It's possible that the optimization doesn't affect the palette as long as
> > > you never use sample_c with the paletted textures.
> >
> > I verified the palette takes effect in the following way:
> >
> > 1. Only support P8A8 format in the driver
> >
> > 2. ran the above command and I saw white OSD text
> >
> > 3. Only support P4A4 format in the driver and don't use
> > 3DSTATE_SAMPLER_PALETTE_LOAD0 to load the value to the texture palette,
> > so the palette keeps unchanged.
> >
> > 4. ran the above command and I saw black OSD text.
> >
> > 5. Load the right value to the texture palette and ran the above command
> > again, I saw white OSD text.
> >
> > Hence I think sample_c with the paletted textures is used in the driver.
>
> That sounds like the palette is actually working, then. Great :)
>
> I doubt that libva would use sample_c - sampling with a shadow comparison?
> It looks like it just uses sample and sample+killpix.
You are right, libva driver doesn't use sample_c message.
> I'm pretty sure the sample_c optimization just uses the palette memory as
> storage for some stuff, so it's quite possible it just works if you're
> only using sample and sample+killpix.
Thanks for the explanation, it makes sense to me.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add wa name from Ville's review to the comment and copypaste
the explanation why we don't care about libva (already broken) from
Ken. Also add conclusion from libva devs that&why this is all fine.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Xiang, Haihao" <haihao.xiang@intel.com>
Cc: libva@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There exists a current workaround to prevent a hang on context switch
should the ring go to sleep in the middle of the restore,
WaProgramMiArbOnOffAroundMiSetContext (applicable to all gen7+). In
spite of disabling arbitration (which prevents the ring from powering
down during the critical section) we were still hitting hangs that had
the hallmarks of the known erratum. That is we are still seeing hangs
"on the last instruction in the context restore". By comparing -nightly
(broken) with requests (working), we were able to deduce that it was the
semaphore LRI cross-talk that reproduced the original failure. The key
was that requests implemented deferred semaphore signalling, and
disabling that, i.e. emitting the semaphore signal to every other ring
after every batch restored the frequent hang. Explicitly disabling PSMI
sleep on the RCS ring was insufficient, all the rings had to be awake to
prevent the hangs. Fortunately, we can reduce the wakelock to the
MI_SET_CONTEXT operation itself, and so should be able to limit the extra
power implications.
Since the MI_ARB_ON_OFF workaround is listed for all gen7 and above
products, we should apply this extra hammer for all of the same
platforms despite so far that we have only been able to reproduce the
hang on certain ivb and hsw models. The last question is whether we want
to always use the extra hammer or only when we know semaphores are in
operation. At the moment, we only use LRI on non-RCS rings for
semaphores, but that may change in the future with the possibility of
reintroducing this bug under subtle conditions.
v2: Make it explicit that the PSMI LRI are an extension to the original
workaround for the other rings.
v3: Bikeshedding variable names and whitespacing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80660
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83677
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Peter Frühberger <fritsch@xbmc.org>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the gen7 pipe control there is an extra bit to flush the media
caches, so let's set it during cache invalidation flushes.
v2: Rename to MEDIA_STATE_CLEAR to be more inline with spec.
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This will allow us to read the number of dispatched compute threads
for GL_ARB_pipeline_statistics_query.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Nikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To get stable CRCs from the DP CRC source we need to reset the
scrambler for each frame. Enable the reset feature when grabbing
CRCs for pipe C on CHV. Pipes A and B were already covered due
sharing the code with VLV.
We can safely extend PIPE_SCRAMBLE_RESET_MASK to deal with CHV since
the extra bit was MBZ on the older platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Was missing.
Issue: VIZ-4701
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.
v2: Used for_each_dsi_port macro instead of for loop
v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check
v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_DWORD_IMM length has been the same ever since gen4. Rename
the define to avoid potential confusion if someone tries to use this
on pre-gen8.
Also correct the comment on MI_MEM_VIRTUAL bit. It's present on 945,g33
and 965 only.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add USE_GGTT define for g4x+ too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Baytrail (Valleyview) and Braswell (Cherryview) uses a complete different
implementation of PSR that we currently have supported for
Haswell and Broadwell. So let's start by adding registers definitions.
I usually don't like commit that adds just registers without using,
but after I put all in one commit I realized that no one would want
to take the AR to review it so I decided to split in order to make
reviewer's life easier. Only last commit in this series will actually
enable the PSR on intel enable panel path.
But as it happens currently with HSW/BDW the plan is to let it
disabled by default (protected by kernel parameter)
while we are able to fully validate it.
v2: Remove a unused bit definition that isn't used on vlv and
reserved on chv as pointed out by Durgadoss.
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just throw in the towel on this one and take the cheap way out.
Based on a patch from Chris Wilson, but checking for a different bit.
Chris' patch checked for even bank layout, this one here for a magic
bit. Given the evidence we've gathered (not much) both work I think,
but checking for the magic bit might be more accurate.
Anyway, works on my gm45 here.
For paranoi restrict to gen4 (and mobile), since we've only ever seen
this on gm45 and i965gm.
Also add some debugfs output so that we can skip the tiled swapping
tests properly in these cases.
v2: Clean up the quirk'ed pin count in free_object to avoid upsetting
the WARN_ON. Spotted by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28813
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45092
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new AUX port irq bits where needed.
v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moved around on SKL, so we need to make sure we read/write the
correct regs.
v2: fixup WIN_POS offsets (Paulo)
zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
