Avoid a possible segfault.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On bo reservation failure, we end up leaking fpriv.
v2 (chk): rebased and added missing free on vm failure as well
Fixes: 5e386b574c ("drm/radeon: fix missing bo reservation")
Cc: stable@vger.kernel.org
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Due to a type mismatch that causes an implicit type conversion, the
upper 32 bits of the GPU address have been zeroed out when adding to the
command buffer.
Picked up by Coverity - CID 1198624.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
May fix stability issues with some newer cards.
v2: print out mc firmware version used and size
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Letting post and refernce divider get to big is bad for signal stability.
v2: increase the limit to 210
Signed-off-by: Christian König <christian.koenig@amd.com>
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some fixes from Intel.
* tag 'drm-intel-fixes-2014-04-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Always use kref tracking for all contexts.
drm/i915: do not setup backlight if not available according to VBT
drm/i915: check VBT for supported backlight type
drm/i915: Disable self-refresh for untiled fbs on i915gm
drm/mm: Don't WARN if drm_mm_reserve_node
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cleans up the checkpatch errors for the merged commit -
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent primary-plane changes for drm, the primary plane's
framebuffer needs to be ref counted the same way as for
non-primary-planes. This was not done by the omapdrm driver, which
caused the ref count to drop to 0 too early, causing problems.
This patch moves the fb unref and ref from omap_plane_update to
omap_plane_mode_set. This way the fb refs are updated for both primary
and non-primary cases, as omap_plane_update calls omap_plane_mode_set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.
Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.
Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.
Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.
This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.
Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omap_gem_op_async(), if a waiter is not added to the wait list, it needs to
be free'd in the function itself.
Make sure we free the waiter for this case.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Patch dfe96ddcfa (omapdrm: simplify locking in
the fb debugfs file) removed taking locks when using omapdrm's debugfs
to dump fb objects.
However, in omap_gem_describe we give a WARN is the lock has not been
taken, so that WARN is now seen every time omapdrm debugfs is used.
So, presuming the removal of locks is ok, we can also remove the WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the planes, including primary planes, are now destroyed by the drm
framework. Thus we no longer need the explicit call to plane->destroy
from the crtc's destroy function.
This patch removes the call, thus fixing the crash caused by double
freeing the plane.
remove omap_crtc->plane->funcs->destroy(omap_crtc->plane)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Print a warning when the user tries to rotate a non-TILER framebuffer.
Also set the rotation to 0, to avoid constant flood of the warnings in
case of page flipping.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_fbdev_create() takes a reference to the fb's gem object with
omap_gem_get_paddr(). However, it never releases it with
omap_gem_put_paddr().
This patch adds the missing omap_gem_put_paddr() to omap_fbdev_free().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Plane rotation with omapdrm is currently broken.
It seems omap_plane_mode_set() expects width and height in screen
coordinates, so pass it like that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment the omap_crtc_pre_apply() handles the enabling, disabling
and configuring of encoders and panels separately from the CRTC (i.e.
the overlay manager).
However, this doesn't work correctly. The encoder driver has to be in
control of its video input (i.e. the crtc) for correct operation.
This problem causes bugs with (at least) HDMI: the HDMI encoder supplies
pixel clock for DISPC, and DISPC supplies video stream for HDMI. The
current code first enables the HDMI encoder, and CRTC after that.
However, the encoder expects the video stream to start during the
encoder's enable, and if it doesn't, there will be sync lost errors.
The encoder enables its video source by calling src->enable(), and this
call goes to omapdrm (omap_crtc_enable), but omapdrm doesn't do anything
in that function. Similarly for disable, which goes to
omap_crtc_disable().
This patch moves the code to setup and enable/disable the crtc to
omap_crtc_enable. and omap_crtc_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When an encoder is no longer connected to a crtc, the driver will leave
the encoder enabled.
This patch adds code to track the encoder used for a crtc, and when the
encoder changes, the old one is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment the DMM driver is never unregistered, even if it's
registered in the omapdrm module's init function. This means we'll get
errors when reloading the omapdrm module.
Fix this by unregistering the DMM driver properly, and also change the
module init to fail if DMM driver cannot be registered, simplifying the
unregister path as we don't need to keep the state whether we registered
the DMM driver or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When unloading omapdrm driver, the omapdrm platform device is
uninitialized last, after the displays have been disconnected omap_crtc
callbacks have been removed. As the omapdrm pdev uninitialization needs
the features uninitialized in earlier steps, a crash is guaranteed.
This patch fixes the uninitialize order so that the omapdrm pdev is
removed first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment it's quite easy to get the following errors when the HDMI
output is enabled or disabled:
[drm:omap_crtc_error_irq] *ERROR* tv: errors: 00008000
The reason for the errors is that the omapdrm driver doesn't properly
handle the sync-lost irqs that happen when enabling the DIGIT crtc,
which is used for HDMI and analog TV. The driver does disable the
sync-lost irq properly, but it fails to wait until the output has been
fully enabled (i.e. the first vsync), so the sync-lost errors are still
seen occasionally.
This patch makes the omapdrm act the same way as the omapfb does:
- When enabling a display, we'll wait for the first vsync.
- When disabling a display, we'll wait for framedone if available, or
odd and even vsyncs.
These changes make sure the output is fully enabled or disabled at the
end of the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always initialize kref for the context, even if we are using fake
contexts for hangstats when there is no hw support, we can forgo the
dance to dereference the ctx->obj and inspect whether we are permitted
to use kref inside i915_gem_context_reference() and _unreference().
My ulterior motive here is to improve the debugging of a use-after-free
of ctx->obj. This patch avoids the dereference here and instead forces
the assertion checks associated with kref.
v2: Refactor the fake contexts to being even more like the real
contexts, so that there is much less duplicated and special case code.
v3: Tweaks.
v4: Tweaks, minor.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: tiny change to backport to drm-intel-fixes.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently it doesn't work. X-tiled self-refresh works flawlessly
otoh. Apparently X still works correctly with linear framebuffers, so
might just be an issue with the initial modeset. It's unclear whether
this just borked wm setup from our side or a hw restriction, but just
disabling gets things going.
Note that this regression was only brought to light with
commit 3f2dc5ac05
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jan 10 14:06:47 2014 +0200
drm/i915: Fix 915GM self-refresh enable/disable
before that self-refresh for i915GM didn't work at all.
Kudos to Ville for spotting a little bug in the original patch I've
attached to the bug.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: rebase on top of drm-next with primary plane support.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jesse's BIOS fb reconstruction code actually relies on the -ENOSPC
return value to detect overlapping framebuffers (which the bios uses
always when lighting up more than one screen). All this fanciness
happens in intel_alloc_plane_obj in intel_display.c.
Since no one else uses this we can safely remove the WARN without
repercussions.
Reported-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 4b28a1f3ef.
This patch duct-tapes over some issue in the current bdw rps patches
which must wait with enabling rc6/rps until the very first batch has
been submitted by userspace.
But those patches aren't merged yet, and for upstream we need to have
an in-kernel emission of the very first batch. I shouldn't have
merged this patch so let's revert it again.
Also Imre noticed that even when rps is set up normally there's a
small window (due to the 1s delay of the async rps init work) where we
could runtime suspend already and blow up all over the place. Imre has
a proper fix to block runtime pm until the rps init work has
successfully completed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will treat Cherryview like Valleyview for most parts. Add a macro
for cases when we need to tell the two apart.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some MIPI panels might not have resolution which is a multiple of 64 like
1366x768. Enable this feature for such panels by default
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Though HS mode also should work.
v2: Change parameter as "bool hs" as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for Generic driver
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, this can stall pipe. We also need DPLL REFA always
enabled
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.
Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.
v2: intel_ring_stopped(), readable comment (Chris)
v3: keep compatibility (Daniel)
References: https://bugs.freedesktop.org/show_bug.cgi?id=75876
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since dma_buf_vunmap() procedes blithely on ignorant of whether the
driver failed to actually unmap the backing storage for the dma-buf, we
need to make a best-effort to do so. This involves not allowing
ourselves to be susceptible to signals causing us to leak the storage.
This should have been detectable with the current i-g-t as a misplaced
signal should have left the pages pinned upon freeing the object where
we have a warning in place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment from Ben: It's a bit unclear whether we need this dance still
on bdw.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needs to happen after clock is running or it doesn't behave correctly.
v2: fix subject (Ville)
make it clearer that this occurs in pre_enable (Paulo)
misc bikesheds (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows sending of the null packets for conformance.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also do a disable later when we write a specific infoframe, but here
we do it to prevent sending a stale one before updating the infoframes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we end up bouncing these around between ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will have another use for the maximum watermark values that the
registers can hold. Pull those out into separate functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though the inactive pipes should have their watermarks set to all 0
with enable=true, we can possibly shave off a few cycles by completely
skipping the merge procedure for inactive pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_pipe_wm will be used to track the state in different stages
of the watermark update process. For that we need to keep a bit
more state in intel_pipe_wm.
We also need to separate the multi-pipe intel_wm_config computation
from ilk_compute_wm_parameters() as that one deals with the future
state, and we need the intel_wm_config to match the current hardware
state at the time we do the watermark merging for multiple pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we've learned over time, the HW context is just a series of GPU
commands that we're able to decode without any changes in
intel_error_decode. Since many bugs recently have been implicated in
the HW context state, it makes sense to dump the whole context object
in a form which can be parsed.
Sample:
render ring --- HW Context = 0x042db000
ringbuffer (render ring) at 0x0160c000; HEAD points to: 0x0160c000
0x0160c000: 0x00000000: MI_NOOP
0x0160c004: 0x00000000: MI_NOOP
0x0160c008: 0x00000000: MI_NOOP
0x0160c00c: 0x00000000: MI_NOOP
0x0160c010: 0x00000000: MI_NOOP
0x0160c014: 0x00000000: MI_NOOP
0x0160c018: 0x00000000: MI_NOOP
0x0160c01c: 0x00000000: MI_NOOP
Unfortunately, our decoder isn't quite smart enough to deal with the
variable length LRIs - but that is a tools problem.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Clarify commit message a bit, seems to have lost a few
crucial words.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I opted to do this instead of grabbing the context reference after
eb_create since eb_create can potentially call the shrinker, and that
makes things very complicated. This simple patch balances the ref count
without requiring a great deal of review to make sure the shrinker path
is safe.
Theoretically (by design) the shrinker can end up destroying a context,
which enforces the reasoning for doing the fix this way instead of
moving the reference to later in the function.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sprite LP2+ registers don't exist on ILK/SNB so don't read them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't do CPU access to GPU contexts so making the GPU access snoop
the CPU caches seems silly, and potentially expensive.
v2: Use !IS_VALLEYVIEW instead of HAS_LLC as this is really
about what the PTEs can represent.
Add a comment clarifying the situation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
There is actually quite a bit of variance based on
the asic.
v2: fix typo noticed by Jerome.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
If you are using the common dp over i2c functionality, it is
asumed that the aux transfer function does not modify the any
of the msg structure other than the reply field. Doing so
breaks the logic in the common code.
v2: update struct drm_dp_aux comments about assumptions
v3 (chk): rebased on upstream changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
We need bare address packets at the start and end of
each i2c over aux transaction to properly reset the connection
between transactions. This mirrors what the existing dp i2c
over aux algo currently does.
This fixes EDID fetches on certain monitors especially with
dp bridges.
v2: update as per Ville's comments
- Set buffer to NULL for zero sized packets
- abort the entre transaction if one of the messages fails
v3: drop leftover debugging code
v4: integrate Thierry's comments
- add comments about address only transactions
- switch back to i and j
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Needed for proper i2c over aux handling for certain
monitors and configurations (e.g., dp bridges or
adapters).
v2: add comments clarifying tx_size setting.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Loading cursors to the LCD controller's SRAM can be corrupted when the
configured pixel clock is relatively slow. This seems to be caused
when we write back-to-back to the SRAM registers.
There doesn't appear to be any status register we can read to check
when an access has completed.
Inserting a dummy read between the writes appears to fix the problem.
Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LGu0
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.15-rc1
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Use standard GPL v2 license text
drm/tegra: Relicense under GPL v2
drm/tegra: Relicense public header under MIT
drm/tegra: Add eDP support
gpu: host1x: export host1x_syncpt_incr_max() function
drm/tegra: prime: Add vmap support
Add support for a couple more simple panels. A few cleanups to the
simple panel driver are also included (gpiod interface conversion,
removal of redundant call to regulator_disable()).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=6Tqg
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v3.15-rc1
Add support for a couple more simple panels. A few cleanups to the
simple panel driver are also included (gpiod interface conversion,
removal of redundant call to regulator_disable()).
* tag 'drm/panel/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: add support for LG LD070WX3-SL01 panel
drm/panel: add support for LG LH500WX1-SD03 panel
drm/panel: simple: Allow DSI panels to provide mode flags
drm/panel: simple: Allow GPIO accesses to sleep
drm/panel: remove redundant regulator_disable()
drm/panel: use gpiod interface for enable GPIO
drm/panel: Add LG 12.9" LCD panel
MAINTAINERS: Add entry for DRM panel drivers
Conflicts:
MAINTAINERS
Pull request of 2014-04-04
The second vmwgfx pull request for the 3.15 merge window.
Contains a fbdev fix by Christopher Friedt, one fix for a locking order
violation introduced in 3.14 (hit when using queries) and finally a
removal of the DRM_AUTH requirement around some vmwgfx IOCTLS where the
caller is already required to have an open handle to the object.
* tag 'vmwgfx-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: correct fb_fix_screeninfo.line_length
drm/vmwgfx: Remove authorization requirements around some more ioctls
drm/vmwgfx: Fix query buffer locking order violation
Pull request of 2014-04-04
Currently only a single patch fixing up mixed use of the ttm_bo_reserve and
ww_mutex APIs
* tag 'ttm-next-2014-04-04' of git://people.freedesktop.org/~thomash/linux:
drm/ttm: Hide the implementation details of reservation
If we get a msg.reply of REPLY_DEFER, we also get an err of 0
so we fail reads with 0 < size and return -EPROTO instead of trying
again.
v2: same fix in i2c code.
Found writing MST support.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Various fbdev fixes and improvements, but nothing big.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bavN
-----END PGP SIGNATURE-----
Merge tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Various fbdev fixes and improvements, but nothing big"
* tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (38 commits)
fbdev: Make the switch from generic to native driver less alarming
Video: atmel: avoid the id of fix screen info is overwritten
video: imxfb: Add DT default contrast control register property.
video: atmel_lcdfb: ensure the hardware is initialized with the correct mode
fbdev: vesafb: add dev->remove() callback
fbdev: efifb: add dev->remove() callback
video: pxa3xx-gcu: switch to devres functions
video: pxa3xx-gcu: provide an empty .open call
video: pxa3xx-gcu: pass around struct device *
video: pxa3xx-gcu: rename some symbols
sisfb: fix 1280x720 resolution support
video: fbdev: uvesafb: Remove impossible code path in uvesafb_init_info
video: fbdev: uvesafb: Remove redundant NULL check in uvesafb_remove
fbdev: FB_OPENCORES should depend on HAS_DMA
OMAPDSS: convert pixel clock to common videomode style
OMAPDSS: Remove unused get_context_loss_count support
OMAPDSS: use DISPC register to detect context loss
video: da8xx-fb: Use "SIMPLE_DEV_PM_OPS" macro
video: imxfb: Convert to SIMPLE_DEV_PM_OPS
video: imxfb: Resolve mismatch between backlight/contrast
...
This patch exports ptn3460_init function so that other modules
can call this function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch removes MODULE_DEVICE_TABLE definition to of_device_id
of DP and MIPI-DSI drivers.
Eyxnos drm should be built as single module so these definitions
should be removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The patch adds MIPI-DSI based S6E8AA0 AMOLED LCD panel driver.
Driver uses mipi_dsi bus to communicate with panel and exposes drm_panel
interface.
v2
- added bus error handling,
- set maxmimum DSI packet size on init,
- removed unsupported brightness drm_panel callbacks,
- minor improvements
v3
- switched to gpiod framework,
- minor fixes in error handling
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds LD9040 parallel RGB panel driver with SPI control interface.
The driver uses drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds driver for Exynos DSI master (DSIM). It is a platform driver
which is registered as exynos_drm_display sub-driver of exynos_drm framework
and implements DRM encoder/connector pair.
It is also MIPI-DSI host driver and provides DSI bus for panels.
It interacts with its panel(s) using drm_panel framework.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds explicit check if there is a connector with
connected status before fbdev initialization. It prevents creation
of default fbdev 1024x768 which is unusable on panels with bigger resolutions.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
MIPI DSI host node can contain child nodes which are not DSI devices.
Checking for existence of reg property can be used to distinguish such nodes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The Dell XPS 8700 has a onboard Display port and HDMI port and no VGA port.
The call intel_crt_init freeze the machine, so skip such call.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73559
Signed-off-by: Giacomo Comes <comes at naic.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This typo may lead to missed RPS interrupts and as a result a too
low or too high frequency for the current workload. The interrupt mask
will be set properly at a subsequent GPU idle event, but can get
corrupted again at the next RPS up/down event.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the inputs provided by hardware team we still use DDR
Rates as 0,1=800, 2=1066, 3=1333.
With this change, Turbo freqs used on current machines matches.
This reverts commit f64a28a7c5.
commit f64a28a7c5
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Nov 4 16:07:00 2013 -0800
drm/i915/vlv: fixup DDR freq detection per Punit spec
v2: Add reference to previous commit which changed this. (Daniel)
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.
The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.
Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.
v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
get reordered wrt. intel_power_domains_init_hw()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the more canonical and concise variant of the GPL v2 license text.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by Tegra Note 7 and supported by the simple-panel
driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel is used by the NVIDIA SHIELD and supported by the
simple-panel driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to differentiate between the different video modes (burst vs.
non-burst, sync pulses vs. sync events) supported by peripherals, pass
the flags that specify this mode in the panel description to the DSI
peripheral device when probed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The enable GPIO for panels may be provided by GPIO expanders on slow
busses (such as I2C), and therefore toggling the GPIO may sleep. Since
these accesses don't happen in interrupt context, use the *_cansleep()
variants of the GPIO API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
regulator_disable() is already performed by panel_simple_disable(),
which is called by panel_simple_remove().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the new GPIO descriptor interface to handle the panel's enable GPIO.
This considerably simplifies the code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: rework to improve readability]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the %pad printk specifier to print dma_addr_t variables. This fixes
warnings on platforms where dma_addr_t has a different size than int or
size_t.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GEM CMA helpers uses a custom mmap implementation based on
remap_pfn_range(). While this works when the buffer DMA and physical
addresses are identical, it fails to take IOMMU into account and tries
to mmap the buffer to userspace using the DMA virtual address instead of
the physical address. This results in mapping random physical pages when
the device is behind an IOMMU.
Use the DMA mapping dma_mmap_writecombine() function instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
entry->size is the size of the node, not the size of the hole after it.
So the code would actually find the hole which can satisfy the
constraints and which is preceded by the smallest node, not the smallest
hole satisfying the constraints.
Reported-by: "Huang, FrankR" <FrankR.Huang@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently drm_pick_cmdline_mode() doesn't care about the interlace
when the given mode line has no "i" suffix. That is, when there are
multiple entries for the same resolution, an interlace mode might be
picked up just depending on the assigned order, and there is no way to
exclude it.
This patch changes the logic for the mode selection, to prefer the
noninterlace mode unless the interlace mode is explicitly given.
When no matching mode is found, it still tries the interlace mode as
fallback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This decreases eviction by up to 20%, by improving the fragmentation
quality. No harm in normal cases that fit VRAM fully (PTS gaming suite).
In some cases, even the VRAM-fitting cases improved slightly (openarena, urban terror).
512kb was measured as the most optimal threshold for 3d workloads common to radeon.
Other drivers may need different thresholds according to their workloads.
v2: Nicer formatting
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clients like i915 need to segregate cache domains within the GTT which
can lead to small amounts of fragmentation. By allocating the uncached
buffers from the bottom and the cacheable buffers from the top, we can
reduce the amount of wasted space and also optimize allocation of the
mappable portion of the GTT to only those buffers that require CPU
access through the GTT.
For other drivers, allocating small bos from one end and large ones
from the other helps improve the quality of fragmentation.
Based on drm_mm work by Chris Wilson.
v3: Changed to use a TTM placement flag
v2: Updated kerneldoc
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Christian König <deathsimple@vodafone.de>
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: David Airlie <airlied@redhat.com>
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/omap: Don't dereference list head when the connectors list is empty
drm/msm/mdp: add timeout for irq wait
drm/msm: validate flags, etc
drm/msm: use componentised device support
drm/msm: add chip-id param
drm/msm: crank down gpu when inactive
drm/msm: spin helper
drm/msm: add hang_debug module param
drm/msm: hdmi audio support
The rcar_du_encoder_init() function can fail and return an error code.
Don't ignore it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Rework of finding the right PLL numbers for display
- Couple of different bugfixes
* 'drm-next-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: fix typo in spectre_golden_registers
drm/radeon: fix endian swap on hawaii clear state buffer setup
drm/radeon: call drm_edid_to_eld when we update the edid
drm/radeon: rework finding display PLL numbers v2
drm/radeon: fix resuming mode in pm runtime resume path
drm/radeon: fix runtime suspend breaking secondary GPUs
drm/radeon: clear needs_reset flag if IB test fails
Print the enable_mask and status_mask from
__i915_{enable,disable}_pipestat() when the caller has messed them up
somehow.
v2: Use pipe_name() (Damien)
Fix a typo in the commit message
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to swap on BE.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This needs to be done to update some of the fields in
the connector structure used by the audio code.
Noticed by several users on irc.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This completely reworks how the PLL parameters are generated and
should result in better matching dot clock frequencies.
Probably needs quite a bit of testing.
bugs: https://bugs.freedesktop.org/show_bug.cgi?id=76564
v2: more cleanup and comments.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
For runtime pm we'd never suspend with the modesetting hw turned on,
so don't try and resume the modesetting hw, as that path will take
locks that the interface that is causing us to wake up might also
take.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Same fix as for nouveau, when we fail with EINVAL, subsequent
gets fail hard, causing the device not to open.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the IB test fails we don't want to reset the card over
and over again, just accept that it isn't working.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=76501
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We have been setting the bit which was originally BIOS dependent since:
commit f05bb0c7b6
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jan 20 16:33:32 2013 +0000
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
Therefore, we do not need to try to figure it out dynamically and we can
just always invalidate the TLBs.
It's a partial revert of:
commit 12b0286f49
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Mon Jun 4 14:42:50 2012 -0700
drm/i915: possibly invalidate TLB before context switch
The original commit attempted to only invalidate when necessary
(very much a relic from the old days). Now, we can just always invalidate.
I guess the old TODO still exists. Since we seem to have abandoned ILK
contexts however, there isn't much point in even remembering.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPIO reads from groups/broadcast register offsets for PCS and
TX return all 1's. If that result gets used for something
we'll probably end up doing something wrong. So warn when that
happens.
FIXME there might be some registers where all 1's is a valid value,
so ideally we should check the register offset instead...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: copypaste the FIXME comment into the code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no point in hiding the DP M/N setup in the update_pll functions.
Just move it to the mode_set function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Iterate over all the PDP registers instead of just printing PDP0 four
times in gen8 PPGTT debugfs info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our validation guys want to have a positive proof that the gfx driver
is indeed using VT-d, since setting up a gfx stack, especially in
early bring-up and by people not versed in linux gfx is a bit tricky.
So provide just that.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VTd has a few too many "outright disable the damn thing" workarounds
accumulated and for validation we want a simple knob to make sure we
disable them all.
Since this is for bdw+ validation and atm we don't have any
workarounds for bdw this option currently does nothing. So currently
this is just a placeholder to make sure reality will match with the
documented process for our validation people.
v2: Fix up param description (Jani).
v3: Actually git add ...
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, the vmwgfx_fb driver would allow users to call FBIOSET_VINFO, but it would not adjust
the FINFO properly, resulting in distorted screen rendering. The patch corrects that behaviour.
See https://bugs.gentoo.org/show_bug.cgi?id=494794 for examples.
Cc: stable@vger.kernel.org
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
These ioctls require a valid handle referenced by the caller to succeed,
which implies that the caller has or has had sufficient privileges.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
The query buffers were reserved while holding the binding mutex, which
caused a circular locking dependency.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
- Inherit/reuse firmwar framebuffers (for real this time) from Jesse, less
flicker for fastbooting.
- More flexible cloning for hdmi (Ville).
- Some PPGTT fixes from Ben.
- Ring init fixes from Naresh Kumar.
- set_cache_level regression fixes for the vma conversion from Ville&Chris.
- Conversion to the new dp aux helpers (Jani).
- Unification of runtime pm with pc8 support from Paulo, prep work for runtime
pm on other platforms than HSW.
- Larger cursor sizes (Sagar Kamble).
- Piles of improvements and fixes all over, as usual.
* tag 'drm-intel-next-2014-03-21' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Include a note about the dangers of I915_READ64/I915_WRITE64
drm/i915/sdvo: fix questionable return value check
drm/i915: Fix unsafe loop iteration over vma whilst unbinding them
drm/i915: Enabling 128x128 and 256x256 ARGB Cursor Support
drm/i915: Print how many objects are shared in per-process stats
drm/i915: Per-process stats work better when evaluated per-process
drm/i915: remove rps local variables
drm/i915: Remove extraneous MMIO for RPS
drm/i915: Rename and comment all the RPS *stuff*
drm/i915: Store the HW min frequency as min_freq
drm/i915: Fix coding style for RPS
drm/i915: Reorganize the overclock code
drm/i915: init pm.suspended earlier
drm/i915: update the PC8 and runtime PM documentation
drm/i915: rename __hsw_do_{en, dis}able_pc8
drm/i915: kill struct i915_package_c8
drm/i915: move pc8.irqs_disabled to pm.irqs_disabled
drm/i915: remove dev_priv->pc8.enabled
drm/i915: don't get/put PC8 when getting/putting power wells
drm/i915: make intel_aux_display_runtime_get get runtime PM, not PC8
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Pull DMA-mapping updates from Marek Szyprowski:
"This contains extension for more efficient handling of io address
space for dma-mapping subsystem for ARM architecture"
* 'for-3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: remove order parameter from arm_iommu_create_mapping()
arm: dma-mapping: Add support to extend DMA IOMMU mappings
If I boot my Broadwell machine to X on a system with Mesa Gallium
llvmpipe instead of i965, then kill X and try to run pm_pc8.c, when we
disable PC8 and call gen6_update_ring_freq(), we will get stuck on an
infinite loop because the frequencies are zero and the variables are
unsigned. This happens because we never ran any batch, so we did not
enable RC6, so the variables are zero. If I run gem_exec_nop before
running pm_pc8, everything works as expected because gem_exec_nop
makes RC6 be enabled.
This commit should prevent the infinite loop, which IMHO is already a
good reason to be merged, but it is not the proper fix to the "RC6 is
not being enabled" problem.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because if we keep the current code, we'll get tons of WARNs on
Broadwell, since the code is Haswell-specific.
We could have also added a Broadwell-specific code there, but it's not
really needed since we never disable LCPLL with the hotplug interrupts
still enabled. So keep the easy-and-simple-to-maintain solution until
we actually need something else.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch Enables the bit for TLB invalidate in GFX Mode register
for Gen7.
According to bspec, When enabled this bit limits the invalidation
of the TLB only to batch buffer boundaries, to pipe_control
commands which have the TLB invalidation bit set and sync flushes.
If disabled, the TLB caches are flushed for every full flush of
the pipeline.
Tested only on vlv platform. Chris has tested on ivb and hsw
platforms.
v2: Adding the explicit enabling of this bit for all Gen7 platforms
instead of only vlv (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #ivb, hsw -Chris
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add w/a markers as suggested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the cast from the pointer diff to fix:
drivers/gpu/drm/i915/i915_cmd_parser.c:405:4: warning: format '%td' expects
argument of type 'ptrdiff_t', but argument 5 has type 'long unsigned int'
[-Wformat]
While at it, use %u for u32.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: After conflict resolution only the "While at it, ..." part
was left standing ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is some thought that the data from the performance counters enabled
via OACONTROL should only be available to the process that enabled counting.
To limit snooping, require that any batch buffer which sets OACONTROL to a
non-zero value also sets it back to 0 before the end of the batch.
This requires limiting OACONTROL writes to happen via MI_LOAD_REGISTER_IMM
so that we can access the value being written. This should be in line with
the expected use case for writing OACONTROL.
v2: Drop an unnecessary '? true : false'
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This brings the code a little more in line with kernel coding style.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As suggested during review, this makes it much more obvious
when the tables are not sorted.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For error state, like the recent modification to ACTHD, FADD also gets
an upper dword. This is useful for debug to make sure the fetch address
and head are similar.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec seems to tell us we need the MI_ARB_ON_OFF w/a around
MI_SET_CONTEXT on gen8.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The computation of required framebuffer size in
commit d978ef1445
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:51 2014 -0800
drm/i915: Wrap the preallocated BIOS framebuffer and preserve for KMS fbcon v12
is too optimistic, and would rely on the invariant fb being
reconstructed to exactly fit each pipe (and probably ignore hardware
limits). Instead, we want to compute the upper bound on what the display
engine will access and ensure that is within the inherited framebuffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Here's the latest iteration of the universal planes work, which I believe is
finally ready for merging. Aside from the minor driver patches to use the
new drm_for_each_legacy_plane() macro for plane loops, these should all have
an r-b from Rob Clark now.
Actual userspace-visibility is currently hidden behind a
drm.universal_planes module parameter so that we can do some experimental
testing of this before flipping it on universally.
* 'primary-plane' of git://people.freedesktop.org/~robclark/linux:
drm/doc: Update plane documentation and add plane helper library
drm: Allow userspace to ask for universal plane list (v2)
drm: Remove unused drm_crtc->fb
drm: Replace crtc fb with primary plane fb (v3)
drm/msm: Switch to universal plane API's
drm: Add drm_crtc_init_with_planes() (v2)
drm: Add plane type property (v2)
drm: Add drm_universal_plane_init()
drm: Add primary plane helpers (v3)
drm: Make drm_crtc_check_viewport non-static
drm/shmobile: Restrict plane loops to only operate on legacy planes
drm/i915: Restrict plane loops to only operate on overlay planes (v2)
drm/exynos: Restrict plane loops to only operate on overlay planes (v2)
drm: Add support for multiple plane types (v2)
This is the equivalent change in the crtc helpers as done to the i915
modeset infrastructure in
commit b0a2658acb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 18 09:37:54 2012 +0100
drm/i915: don't disable disconnected outputs
This was originally introduced to make encoder sharing on radone
easier for userspace, but:
- It is policy and as such belongs into userspace. E.g. personally I'm
fairly annoyed that a flaky cable results in permanent changes of
the desktop layout, so I'll kick out DEs which do this. Worse if the
kernel also tries to be clever.
- It's inconsistent: We only kill disconnected outputs on setCrtc
(which userspace might also call when just changing the
framebuffer), but not when e.g. we receive a hpd event or in the
output poll worker.
- It's unexpected behaviour for the userspace driver, at least in the
intel ddx we've had tons of bugs where the driver fell over and
killed the X session becuase pageflips/vblanks suddenly stopped
working. We've had to fix this by wrapping every single setCrtc int
a big "recover kms state from the kernel again" operation.
- It's suprising for the kernel, too: It took a few mails between Rob,
Matt and me for them to notice that little dragon wreaking havoc
with the universal plane framebuffer refcounting.
- Userspace can cope with it and e.g. Gnome already kills disconnected
outputs and reconfigures the desktop automatically. And since there
have been no regression reports for the i915 change from over 1 year
ago I think all other DEs are also ready.
Note that the lines removed in this patch go back to
commit a3a0544b2c
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Aug 31 15:16:30 2009 +1000
drm/kms: add explicit encoder disable function and detach harder.
Unfortunately the patch itself doesn't explain a hole lot about why it
was added ...
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was introduced in
commit 25f397a429
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 19 18:57:11 2013 +0200
drm/crtc-helper: explicit DPMS on after modeset
but due to a bit of rebase fail on my side the patch actually merged
put one hunk on the wrong side of a break statement. Fix this up.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a BUG_ON(bo->sync_obj != NULL); in ttm_bo_release_list.
Cc: stable@vger.kernel.org #v3.10+
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should ensure we don't hit a locking problem when someone
wakes us up via a connector, we should never go into suspend
while the display is on anyways.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace clients which wish to receive all DRM planes (primary and
cursor planes in addition to the traditional overlay planes) may set the
DRM_CLIENT_CAP_UNIVERSAL_PLANES capability.
v2: Hide behind drm.universal_planes module option [suggested by
Daniel Vetter]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Use drm_universal_plane_init() and drm_crtc_init_with_planes() rather
than the legacy drm_plane_init() / drm_crtc_init(). This will ensure
that the proper primary plane is registered with the DRM (and eventually
exposed to userspace in future patches).
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a new drm_crtc_init_with_planes() to allow drivers to provide
specific primary and cursor planes at CRTC initialization. The existing
drm_crtc_init() interface remains to avoid driver churn in existing
drivers; it will initialize the CRTC with a plane helper-created primary
plane and no cursor plane.
v2:
- Move drm_crtc_init() to plane helper file so that nothing in the DRM
core depends on helpers. [suggested by Daniel Vetter]
- Keep cursor parameter to drm_crtc_init_with_planes() a void* until
we actually add cursor support. [suggested by Daniel Vetter]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add a plane type property to allow userspace to distinguish plane types.
v2: Driver-specific churn eliminated now that drm_plane_init() and
drm_universal_plane_init() were separated out in a previous patch.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add a new plane initialization interface for universal plane support
that allows a specific plane type (primary, cursor, or overlay) to
be specified.
drm_plane_init() remains as a compatibility API to reduce churn in
existing drivers. The 'bool priv' parameter has been changed to
'bool is_primary' under the assumption that all existing uses of
private planes were representing primary planes.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When we expose non-overlay planes to userspace, they will become
accessible via standard userspace plane API's. We should be able to
handle the standard plane operations against primary planes in a generic
way via the modeset handler.
Drivers that can program primary planes more efficiently, that want to
use their own primary plane structure to track additional information,
or that don't have the limitations assumed by the helpers are free to
provide their own implementation of some or all of these handlers.
v3: Tweak kerneldoc formatting slightly to avoid ugliness
v2:
- Move plane helpers to a new file (drm_plane_helper.c)
- Tighten checks on update handler (check for scaling, CRTC coverage,
subpixel positioning)
- Pass proper panning parameters to modeset interface
- Disallow disabling primary plane (and thus CRTC) if other planes are
still active on the CRTC.
- Use a minimal format list that should work on all hardware/drivers.
Drivers may call this function with a more accurate plane list to
enable additional formats they can support.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
This function will be used by the universal plane helpers and may also
be useful for individual drivers.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.
v2: Switch to using drm_for_each_legacy_plane()
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Ensure that existing driver loops over all planes do not change behavior
when we begin adding new types of planes (primary and cursor) to the DRM
plane list in future patches.
v2: Switch to using drm_for_each_legacy_plane()
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
The DRM core currently only tracks "overlay"-style planes. Start
refactoring the plane handling to allow other plane types (primary and
cursor) to also be placed on the DRM plane list.
v2: Add drm_for_each_legacy_plane() iterator to smooth transition
of drivers with plane loops.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
This sould be enough.
v2: BDW should also run hsw_runtime_resume (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's what the spec said! And HSW needs it through pcode (you can
only read it through MCHBAR), so create hsw_write_dcomp to abstract
the weirdness.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're adding runtime suspend support to more platforms, so organize
the code in a way that all a new platform needs to do is to add its
own gen-specific functions. Also rename the i915_ functions to intel_
to make it clear that it's the top level one, not something that just
runs on i915 platforms.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we don't keep the hotplug interrupts enabled anymore, we can
kill the regsave struct and just cal the normal IRQ preinstall,
postinstall and uninstall functions. This makes it easier to add
runtime PM support to non-HSW platforms.
The only downside is in case we get a request to update interrupts
while they are disabled, won't be able to update the regsave struct.
But this should never happen anyway, so we're not losing too much.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only enable interrupts at postinstall.
And now on ILK/SNB/IVB/HSW the irq_preinstall and irq_postinstall
functions leave the hardware in the same state.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can merge all the common code from postinstall and uninstall.
v2: - Rebase.
- While at it, remove useless { and }.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To merge the common code of ironlake_irq_preinstall and
ironlake_irq_uninstall.
We should also probably do something about that HSWSTAM write on a
later commit.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail due to drm_i915_private_t typedef removal.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Missing from gen8_irq_uninstall.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the latest changes, ibx_irq_preinstall and ibx_irq_uninstall are
the same, so remove one of the copies and rename the other to
ibx_irq_reset (since we're using the "reset" name for things which are
called both at preinstall and uninstall).
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the preinstall stage we should just disable all the interrupts, but
we currently enable all the south display interrupts due to the way we
touch SDEIER at the IRQ handlers (note: they are still masked and our
IRQ handler is disabled). Instead of doing that, let's make the
preinstall stage just disable all the south interrupts, and do the
proper interrupt dance/ordering at the postinstall stage, including an
assert to check if everything is behaving as expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After all, we call ibx_irq_preinstall from gen8_irq_preinstall.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like ibx_irq_preinstall. We'll call this from somewhere else in
the next patch.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The duplicate was at an _uninstall function, so rename it to
gen5_gt_irq_reset.
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as SERR_INT and the other IIR registers: reset on
preinstall/uninstall and WARN for non-zero values at postinstall. This
one also doesn't need double-clear.
v2: - Remove the is_zero assertion (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The SERR_INT register is very similar to the other IIR registers, so
let's zero it at preinstall/uninstall and WARN for a non-zero value at
postinstall, just like we do with the other IIR registers. For this
one, there's no need to double-clear since it can't store more than
one interrupt.
v2: - Remove the is_zero assertion (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It should already be masked and disabled and zeroed at the preinstall
and uninstall stages. Also, the current code just writes to IIR once,
and this is not a guarantee that it will be cleared, so it's wrong
anyway.
The whole reason for the paranoia is that we're going to start calling
the IRQ preinstall/postinstall/uninstall from the runtime PM
callbacks, so we need to make sure everything is behaving as expected.
v2: - Change the original DRM_ERROR to WARN and clear IIR in case it's
not zero (Ben).
- Improve commit message (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And the equivalent GEN8_IRQ_INIT_NDX macro. These macros are for the
postinstall functions. The next patch will improve this macro.
v2: - Adjust to the new POSTING_READ scheme (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IRQ_INIT and IRQ_FINI macros are basically the same thing, with
the exception that IRQ_FINI doesn't properly clear IIR twice and
doesn't have as many POSTING_READs as IRQ_INIT. So rename the INIT
macro to IRQ_RESET and use it everywhere.
v2: - Fix error in the commit message (Chris).
- Adjust to the new POSTING_READ scheme (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the only thing missing, apparently.
v2: - Fix typo (Ben).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the _INIT macro: the goal is to reuse the GEN8 macros, but
there are still some slight differences.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And rename it to GEN5_IRQ_INIT.
We have discussed doing equivalent changes on July 2013, and I even
sent a patch series for this: "[PATCH 00/15] Unify interrupt register
init/reset". Now that the BDW code was merged, I have one more
argument in favor of these changes.
Here's what really changes with the Gen 5 IRQ init code:
- We now clear the IIR registers at preinstall (they are also
cleared at postinstall, but we will change that later).
- We have an additional POSTING_READ at the IMR register.
v2: - Fix typo in commit message.
- Add POSTING_READ calls to the macros (Ben, Daniel, Jani).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This interrupt gets initialized with a different IER value, so it was
not using the macro. The problem is that we plan to modify the macro
to make it do additional things, and we want the SDE interrupts
updated too. So let's make sure we call the macro, then, after it, we
do the necessary SDE-specific changes.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The goal is to reuse the GEN8 macros, but a few changes are needed, so
let's make things easier to review.
I could also use these macros on older code, but since I plan to
change how the interrupts are initialized, we'll risk breaking the
older code in the next commits, so I'll leave this out for now.
v2: - Rebase.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch reads the DRRS support and Mode type from VBT fields.
The read information will be stored in VBT struct during BIOS
parsing. The above functionality is needed for decision making
whether DRRS feature is supported in i915 driver for eDP panels.
This information helps us decide if seamless DRRS can be done
at runtime to support certain power saving features. This patch
was tested by setting necessary bit in VBT struct and merging
the new VBT with system BIOS so that we can read the value.
v2: Incorporated review comments from Chris Wilson
Removed "intel_" as a prefix for DRRS specific declarations.
v3: Incorporated Jani's review comments
Removed function which deducts drrs mode from panel_type. Modified some
print statements. Made changes to use DRRS_NOT_SUPPORTED as 0 instead of -1.
v4: Incorporated Jani's review comments.
Modifications around setting vbt drrs_type.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
[danvet: Drop the misleading/redundant comment about the added drrs
field in the vbt struct as discussed with Jani on irc.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently drm_cflush_virt_rage() takes a char* so the caller probably
has to do pointless casting to avoid compiler warnings. Make the
argument void* instead to avoid such issues.
v2: Use void* arithmetic (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull all the gmch platform hotplug interrupt handling into one
function.
v2: Move the IIR check to the caller
s/drm_i915_private_t/struct drm_i915_private/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add posting read comment suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a need for duplicated parsing of the RP_STATE_CAPS register (and
the setting of the associated fields). To reuse some code, we can
extract the function into a simple helper.
This patch also addresses the fact that we missed doing this for gen8,
something we should have done anyway.
This could be two patches, one to extract, and one to add gen8, but it's
trivial enough that I think one is fine. I will accept a request to
split it. Please notice the fix addressed by v2 below.
Valleyview is left untouched because it is different.
v2: Logically rebased on top of
commit dd0a1aa19b
Author: Jeff McGee <jeff.mcgee@intel.com>
Date: Tue Feb 4 11:32:31 2014 -0600
drm/i915: Restore rps/rc6 on reset
Note with the above change the fix for gen8 is also handled (which was
not the case in Jeff's original patch).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Programming it outside of the rp0-rp1 range is considered a programming
error. Since we do not know that the previous value would actually be in
the range, program something we've read from the hardware, and therefore
know will work.
This is potentially an issue for platforms whose ranges are outside the
norms given in the programming guide (ie. early silicon)
v2: Use RP1 instead of RPn
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split the post_disable hooks for DP to g4x and vlv variants. We'll
need another variant soon, so this should make it look a bit cleaner.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These were apparently meant to protect the SAREA which only has
room for two pipes, but things clearly went a bit wonky when
first the .update_plane() hooks were split up and then pipe C
got introduced.
The checks actually protecting the SAREA live in
intel_crtc_update_sarea() these days, so the checks in the primary
plane update hooks are just historical leftovers which are to be
eliminated.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Progess according to the deprecation plan laid out in
commit b30324adaf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:11:25 2013 +0100
drm/i915: Deprecated UMS support
and disable UMS for 3.16. Note that it has been over 5 years since the
last UMS-supporting piece of userspace was released.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no longer users of drm_i915_private_t. Drop the typedef. Good
riddance.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Chris Wilson <chris@chris-wislon.co.uk>
[danvet: Add the hunk in i915_cmd_parser.c here which had to be
relocated to the how this was merged.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The reg_read whitelist has a gen bitmask to code the gens we're allowing
the register to be read on. Until now, it was a literal, but we can be
a bit more expressive.
To ease the review, a small test program:
$ cat bit-range.c
#include <stdio.h>
#include <stdint.h>
#define U32_C(x) x ## U
#define GENMASK(h, l) (((U32_C(1) << ((h) - (l) + 1)) - 1) << (l))
#define GEN_RANGE(l, h) GENMASK(h, l)
int main(int argc, char **argv)
{
printf("0x%08x\n", GEN_RANGE(1, 1));
printf("0x%08x\n", GEN_RANGE(1, 2));
printf("0x%08x\n", GEN_RANGE(4, 4));
printf("0x%08x\n", GEN_RANGE(4, 5));
printf("0x%08x\n", GEN_RANGE(1, 31));
printf("0x%08x\n", GEN_RANGE(4, 8));
return 0;
}
$ ./bit-range
0x00000002
0x00000006
0x00000010
0x00000030
0xfffffffe
0x000001f0
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's change the i915_cur_delayinfo to i915_frequency_info to be in sync
with new RPS naming convention.
v2: Add "i915_frequency_info" as debugfs interface name (Ben)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These defines are only used in intel_uncore.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function isn't used outside this file anymore.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_DEBUG_KMS includes printing the function name.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those values are, global, only used in one function and already stored
in mode_config.cursor_{width,height}.
As a result, this initialization code has been moved from the
crtc_init() function to the global modeset_init() one.
I also renamed CURSOR_{WIDTH,HEIGHT} to MAX_CURSOR_{WIDTH,HEIGHT} to be
more accurate about what these value really are.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Besides D0 device state we need the proper power wells to be on on
some platforms, so get the port power domain reference instead of an RPM
reference.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of reading out the CD clock rate from the HW at each modeset, do
this only during driver init and resume and use the cached value during
modeset. This moves things towards a state where the sw and hw side
setup is separated. It's also needed for VLV RPM, where we don't put
device into D0 state until modeset_global_resources is called and thus
can't access any display/gfx registers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When trying to determine whether RPS is working as intended, more
information is better. In particular, what interrupts are being
generated and the various thresholds for generating them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mesa needs to be able to write OACONTROL in order to expose the
Observability Architecture's performance counters via OpenGL.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add comment that this is just a temporary work-around and
that we need to check more things before we can allow OACONTROL writes
for real everywhere.]
[danvet 2: Squash in fixup to avoid a DRM_ERROR due to unsorted reg
list, spotted by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So userspace can query the kernel for command parser support.
v2: Add i915_cmd_parser_get_version(), history log, and kerneldoc
OTC-Tracker: AXIA-4631
Change-Id: I58af650db9f6753c2dcac9c54ab432fd31db302f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL and MI_FLUSH_DW have bits that would write to the
hardware status page. The driver stores request tracking info
there, so don't let userspace overwrite it.
v2: trailing comma fix, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are used to implement scanline waits in the X server.
v2: Use #defines instead of magic numbers
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers are currently used by mesa for blitting,
transform feedback extensions, and performance monitoring
extensions.
v2: REG64 macro
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Intel DDX uses these to implement scanline waits in the X server.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec defines most of these commands as privileged. A few others,
like the semaphore mbox command and some display commands, are also
reserved for the driver's use. Subsequent patches relax some of
these restrictions.
v2: Rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add command tables defining irregular length commands for each ring.
This requires a few new command opcode definitions.
v2: Whitespace adjustment in command definitions, sparse fix for !F
OTC-Tracker: AXIA-4631
Change-Id: I064bceb457e15f46928058352afe76d918c58ef5
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
commit 93a25a9e2d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 6 09:40:43 2014 +0100
drm/i915: Disable full ppgtt by default
By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2
means full, all other values are reserved.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This file contains all necessary defines, prototypes and typesdefs for
manipulating GEN graphics address translation (this does not include the
legacy AGP driver)
Reiterating the comment in the header,
"Please try to maintain the following order within this file unless it
makes sense to do otherwise. From top to bottom:
1. typedefs
2. #defines, and macros
3. structure definitions
4. function prototypes
Within each section, please try to order by generation in ascending
order, from top to bottom (ie. GEN6 on the top, GEN8 on the bottom)."
I've made some minor cleanups, and fixed a couple of typos while here -
but there should be no functional changes.
The purpose of the patch is to reduce clutter in our main header file,
making room for new growth, and make documentation of our interfaces
easier by splitting things out.
With a little more work, like making i915_gtt a pointer, we could
potentially completely isolate this header from i915_drv.h. At the
moment however, I don't think it's worth the effort.
Personally, I would have liked to put the PTE encoding functions in this
file too, but I didn't want to rock the boat too much.
A similar patch has been in use on my machine for some time. This exact
patch though has only been compile tested.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract all this logic into a new helper function
semaphore_wait_to_signaller_ring because:
- The current code has way too much magic.
- The current code doesn't look at bi16, which encodes VECS signallers
on HSW. Those are just added after the fact, so can't be encoded in
a neat formula.
- The current logic can't blow up since it limits its value range
sufficiently, but that's a bit too tricky to rely on in my opinion.
Especially when we start to add bdw support.
- I'm not a big fan of the explicit ring->semaphore_register list, but
I think it's more robust to use the same mapping both when
constructing the semaphore commands and when decoding them.
- Finally add a FIXME comment about lack of broadwell support here,
like in the earlier ipehr semaphore cmd detection function.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Actually drop the untrue claim in the commit message Chris
pointed out.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently not an issue since we don't emit sempahores, but better
not forget about those.
As a little prep work extract the ipehr decoding for cleaner control
flow. And apply a bit of polish.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gupta, Sourab" <sourab.gupta@intel.com>
Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because gen6_gt_force_wake_{get,put} should already be responsible for
getting/putting runtime PM. If we keep these calls, debugfs will not
be testing the get/put calls of the forcewake functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If runtime PM is enabled and we unset all modes, we will runtime
suspend after __intel_set_mode() , then function
intel_modeset_check_state() will try to read the HW state while it is
suspended and trigger lots of WARNs because it shouldn't be reading
registers.
So on this patch we make intel_ddi_connector_get_hw_state() return
false in case the power domain is disabled, and we also make
intel_display_power_enabled() return false in case the device is
suspended. Notice that we can't just use
intel_display_power_enabled_sw() because while the driver is being
initialized the power domain refcounts are not reflecting the real
state of the hardware.
Just for reference, I have previously published an alternate patch for
this problem, called "drm/i915: get runtime PM at intel_set_mode".
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At i915_display_info, don't call cursor_position() for a disabled
CRTC, since the CRTC may be on a powered down pipe, and this will
cause "Unclaimed register before interrupt" error messages.
Testcase: igt/pm_pc8/debugfs-read
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we may get some WARNs complaining that we're reading a
register while we're suspended.
Testcase: igt/pm_pc8/debugfs-read
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid WARNs when we call it.
Testcase: igt/pm_pc8/reg-read-ioctl
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75693
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far force_wake_timer was only used by gen6_gt_force_wake_put. Since
we always had balanced gen6_gt_force_wake_get/put calls, we could
guarantee balanced calls to intel_runtime_pm_get/put.
Commit 8232644ccf, "drm/i915: Convert
the forcewake worker into a timer func" started scheduling the
force_wake_timer at gen6_read, which resulted in an unbalanced
runtime_pm refcount.
So this commit just reverts to the old behavior until we can find a
proper way to used delayed force_wake from the register read/write
macros without leaving the runtime_pm refcounts unbalanced and without
runtime suspending the driver while forcewake is active.
Testcase: igt/pm_pc8/rte
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76544
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Alex Deucher