Add the PCIe EP mode on iMX6QP/Q/DL sabresd platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Add the iMX7D PCIe EP mode, and verify the EP mode on SDB board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Add the iMX6SX PCIe EP mode, and verify the EP mode on SDB board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Since iMX6Q/DL PCIe have the PM limitation (ERR005723).
Only enable PCIe in the xxx-pcie.dts files.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Sensors are connected to M4 and not to A-Core.
Sensors will not be exposed to A-Core via standard
i2c interface but via an i2c proxy layer over rpmsg.
Remove the dts entry to avoid the probe error messages and
add a separate dts file for the case where someone wishes to
rework the board themselves and connect sensors for testing purposes.
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Arulpandiyan Vadivel <arulpandiyan_vadivel@mentor.com>
Signed-off-by: Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com>
(cherry picked from commit 05f0c61222bcb43b400b239d780df1ee55c5668f)
i.MX6Q/DL ENET cannot wake up system in wait mode because ENET
tx & rx interrupt signal don't connect to GPC. Add ENET GPIO IRQ
workaround for sabresd/sabreauto boards.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
on SDB board, LCD1_DATA07 is shared by lcdif1 and csi1, so add -lcdif1 dts
file to resovle the conflict.
[ 503.947201] imx6sx-pinctrl 20e0000.iomuxc: pin MX6SX_PAD_LCD1_DATA07 already requested by 2220000.lcdif; cannot claim for 0-003c
[ 503.958957] imx6sx-pinctrl 20e0000.iomuxc: pin-59 (0-003c) status -22
[ 503.965560] imx6sx-pinctrl 20e0000.iomuxc: could not request pin 59 (MX6SX_PAD_LCD1_DATA07) from group csigrp-0 on device 20e0000.iomuxc
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Add focaltech new touch panel ft5426 support.
Set the ft5426 as default panel for dts. If want to use the old panel, then
it needs to boot with imx7ulp-evk-ft5416.dtb file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
SDIO wifi and sd1 slot share one usdhc, this patch add sd1 slot support
on imx7ulp evk board, need to do hardware rework first.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Add emmc support for imx6sx-sdb board, due to this support
need remove sd4 sd card slot and solder an eMMC chip, so
this patch add imx6sx-sdb-emmc.dts file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Add uart5 DTE mode pinctrl set for imx6q-sabresd board. Since there
have pin confliction, so add new dts file.
Signed-off-by: Fugang Duan <B38611@freescale.com>
(cherry picked from commit d63b40d5b1b05992d2328ef0bdc80ec5d96f2dce)
Signed-off-by: Arulpandiyan Vadivel <arulpandiyan_vadivel@mentor.com>
Signed-off-by: Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com>
Add uart4 DCE and DTE pinctrl set. Since there have pin confliction,
so add new dts file. To avoid a flood of dts files, there comment out
DTE pinctrl set. If user want to test DTE mode, it needs to rebuild
the DTB file.
Signed-off-by: Fugang Duan <B38611@freescale.com>
(cherry picked from commit a3602fa5796bb86ba432474220389ec712bde92a)
Signed-off-by: Arulpandiyan Vadivel <arulpandiyan_vadivel@mentor.com>
Signed-off-by: Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com>
Alistair Francis