calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789https://bbs.archlinux.org/viewtopic.php?id=156964
Signed-off-by: Adis Hamzić <adis@hamzadis.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch allows the CPU to map the stolen vram segment
directly rather than going through the PCI BAR. This
significantly improves performance for certain workloads with
a properly patched ddx.
Use radeon.fastfb=1 to enable it (disabled by default).
Currently only supported on RS690, but support for RS780/880
and newer APUs may be added eventually.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Let's allow GCC to optimize better.
This exposed some five unused functions, but this patch doesn't remove them.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Making it easier to control when it is executed.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The IB pool is in gart memory, so it is completely
superfluous to unpin / repin it on suspend / resume.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Call it in the asic startup callback on all asics.
Previously r600 and rv770 called it in the startup
and resume callbacks while all the other asics called
it in the startup callback.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Removing all the different error messages and
having just one standard behaviour over all
chipset generations.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Each ring type may need a different variant.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König<christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Required for future functionality.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If accel is not working many subsystem such as the ib pool might not be
initialized properly that can lead to segfault inside kernel when cs
ioctl is call with non working acceleration. To avoid this make sure
the accel working flag is false when an error in GPU startup happen and
return EBUSY from cs ioctl if accel is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somewhat specializaed sub-allocator designed to perform sub-allocation
for command buffer not only for current cs ioctl but for future command
submission ioctl as well. Patch also convert current ib pool to use
the sub allocator. Idea is that ib poll buffer can be share with other
command buffer submission not having 64K granularity.
v2 Harmonize pool handling and add suspend/resume callback to pin/unpin
sa bo (tested on rv280, rv370, r420, rv515, rv610, rv710, redwood, cayman,
rs480, rs690, rs880)
v3 Simplify allocator
v4 Fix radeon_ib_get error path to properly free fence
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a start fence driver helper function which will be call
once for each ring and will compute cpu/gpu addr for fence
depending on wether to use wb buffer or scratch reg.
This patch replace initialize fence driver separately which
was broken in regard of GPU lockup. The fence list for created,
emited, signaled must be initialize once and only from the
asic init callback not from the startup call back which is
call from the gpu reset.
v2: With this in place we no longer need to know the number of
rings in fence_driver_init, also writing to the scratch reg
before knowing its offset is a bad idea.
v3: rebase on top of change to previous patch in the serie
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
So we used to use lpfn directly to restrict VRAM when we couldn't
access the unmappable area, however this was removed in
93225b0d7b as it also restricted
the gtt placements. However it was only later noticed that this
broke on some hw.
This removes the active_vram_size, and just explicitly sets it
when it changes, TTM/drm_mm will always use the real_vram_size,
and the active vram size will change the TTM size used for lpfn
setting.
We should re-work the fpfn/lpfn to per-placement at some point
I suspect, but that is too late for this kernel.
Hopefully this addresses:
https://bugs.freedesktop.org/show_bug.cgi?id=35254
v2: fix reported useful VRAM size to userspace to be correct.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should not allocate any object into unmappable vram if we
have no means to access them which on all GPU means having the
CP running and on newer GPU having the blit utility working.
This patch limit the vram allocation to visible vram until
we have acceleration up and running.
Note that it's more than unlikely that we run into any issue
related to that as when acceleration is not woring userspace
should allocate any object in vram beside front buffer which
should fit in visible vram.
V2 use real_vram_size as mc_vram_size could be bigger than
the actual amount of vram
[airlied: fixup r700_cp_stop case]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory. The driver can then read
the values from the shadow rather than reading back from the
register across the bus. Writeback can be disabled by setting
the no_wb module param to 1.
On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer
v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.
[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table. Check both and make sure
we have a value system memory clock value.
v2: make sure rs690_pm_info is called on rs780/rs880 as well.
fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.
[airlied: fixup nouveau properly to build]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
of the times but once in a while it fails for no obvious
reasons (same status than previous reset just no same
happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
it seems that it can fail after a bunch (reset every
2sec for 3hour bring down the GPU & computer)
This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).
Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.
Next step is to record the bogus command that leaded to
the lockup.
V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Add module option to force the display priority
0 = auto, 1 = normal, 2 = high
- Default to high on r3xx/r4xx/rv515 chips
Fixes flickering problems during heavy acceleration
due to underflow to the display controllers
- Fill in minimal support for RS600
v2 - update display priority when bandwidth is updated
so the user can change the parameter at runtime and it
will take affect on the next modeset.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check that atom cmd and data tables are valid
before using them.
(v2)
- fix some whitespace errors noticed by Rafał Miłecki
- check a few more cases
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Look up i2c bus in the power table and expose it.
You'll need to load a hwmon driver for any chips
on the bus, this patch just exposes the bus.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
In essence this creates a home for all asic specific declarations in
radeon_asic.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.
Tested on R100,R200,R300,R400,R500,R600,R700 family.
V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This detects if the sideport memory is enabled and
if it is VRAM is evicted on suspend/resume.
This should fix s/r issues on some IGPs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume on my rv530 laptop surface cntl was left disabled, so
wierd stuff would happen with rendering to a tiled front buffer.
This checks if the surface regs are assigned to bos and reprograms
the surface registers on resume using the same path that clears
them all on init.
Signed-off-by: Dave Airlie <airlied@redhat.com>
