CHV display PHY registes have two swing margin/deemph settings. Make it
clear which ones we're using.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV was forgotten the intel_{dp,hdmi}_prepare() were introduced (or the
chv patches were still in flight?). Call these when enabling the ports.
Things tend to work much better when we actually write something
to the port registers :)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future platform will use config->ddi_pll_sel in a different way.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.
v2: Patch rebased
v3: Daniel's review comments
- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
track drrs support
v4: Jesse's review comments
- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to take the connection mutex around the link status
check for non-MST case, but also around the MST link training
on short HPDs.
I suspect we actually should have a dpcd lock in the future as
well, that just lock the local copies of dpcd and flags stored
from that.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already call intel_display_power_get, which will get a power
domain, and every power domain should get a runtime PM reference,
which will wake up the machine.
v2: - Also touch intel_crt_detect() (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Fixup commit message as spotted by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to check for this in psr_enable, everything else is
already protect by the dev_priv->psr.enabled checks. Those need the
psr locking, but these functions are called infrequent enough that the
locking overhead is negligible.
Suggested by Chris Wilson.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really optional to have locking ...
The ugly part is how much locking the psr work needs since it has to
recheck everything. Which is way too much. But we need to ditch the
psr work in it's current form anyway and implement proper frontbuffer
tracking.
The other nasty bit that had to go was the delayed work cancle in
psr_exit. Which means a bunch of races just became a bit more likely,
but mea culpa.
v2: Fixup HAS_PSR checks, resulting in uninitialized mutex issues.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that no one else is using this in the
enable function and also that the work item hasn't raced
with the disabled function.
v2: Improve bisectability by moving one hunk to an earlier patch.
v3: added missing dev_priv declaration (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we track the sw side (psr.active) correctly and WARN
everywhere it might get out of sync with the hw.
v2: Fixup WARN_ON logic inversion, reported by Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to fish that one out through looping is a bit a locking
nightmare. So just set it and use it in the work struct.
v2:
- Don't Oops in psr_work, spotted by Rodrigo.
- Fix compile warning.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can't review this right now due to lack of DRRS code.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to runtime pm and system s/r we need to restore hw state every
time we enable a pipe again. Hence trying to avoid that is just
pointless book-keeping which Rodrigo then tried to work around by
manually adding psr_setup calls to our resume code.
Much simpler to just remove code instead.
v2: Properly bail out of psr exit if psr isn't enabled. Spotted by
Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
This reverts commit 38aecea0cc.
This breaks Haswell Thinkpad + Lenovo dock in SST mode with a HDMI monitor attached.
Before this we can 1920x1200 mode, after this we only ever get 1024x768, and
a lot of deferring.
This didn't revert clean, but this should be fine.
bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1117008
Cc: stable@vger.kernel.org # v3.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way only the dynamic WRPLL selection for hdmi ddi mode is
done in intel_ddi_pll_select.
v2: Don't clobber the precomputed values when selecting clocks fro
hdmi encoders.
v3 (from Paulo): Rebase on top of the s/IS_HASWELL/HAS_DDI/ patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't let it fall in the HAS_PCH_SPLIT() case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Accurate frontbuffer tracking and frontbuffer rendering invalidate, flush and
flip events. This is prep work for proper PSR support and should also be
useful for DRRS&fbc.
- Runtime suspend hardware on system suspend to support the new SOix sleep
states, from Jesse.
- PSR updates for broadwell (Rodrigo)
- Universal plane support for cursors (Matt Roper), including core drm patches.
- Prefault gtt mappings (Chris)
- baytrail write-enable pte bit support (Akash Goel)
- mmio based flips (Sourab Gupta) instead of blitter ring flips
- interrupt handling race fixes (Oscar Mateo)
And old, not yet merged features from the previous round:
- rps/turbo support for chv (Deepak)
- some other straggling chv patches (Ville)
- proper universal plane conversion for the primary plane (Matt Roper)
- ppgtt on vlv from Jesse
- pile of cleanups, little fixes for insane corner cases and improved debug
support all over
* tag 'drm-intel-next-2014-06-20' of git://anongit.freedesktop.org/drm-intel: (99 commits)
drm/i915: Update DRIVER_DATE to 20140620
drivers/i915: Fix unnoticed failure of init_ring_common()
drm/i915: Track frontbuffer invalidation/flushing
drm/i915: Use new frontbuffer bits to increase pll clock
drm/i915: don't take runtime PM reference around freeze/thaw
drm/i915: use runtime irq suspend/resume in freeze/thaw
drm/i915: Properly track domain of the fbcon fb
drm/i915: Print obj->frontbuffer_bits in debugfs output
drm/i915: Introduce accurate frontbuffer tracking
drm/i915: Drop schedule_back from psr_exit
drm/i915: Ditch intel_edp_psr_update
drm/i915: Drop unecessary complexity from psr_inactivate
drm/i915: Remove ctx->last_ring
drm/i915/chv: Ack interrupts before handling them (CHV)
drm/i915/bdw: Ack interrupts before handling them (GEN8)
drm/i915/vlv: Ack interrupts before handling them (VLV)
drm/i915: Ack interrupts before handling them (GEN5 - GEN7)
drm/i915: Don't BUG_ON in i915_gem_obj_offset
drm/i915: Grab dev->struct_mutex in i915_gem_pageflip_info
drm/i915: Add some L3 registers to the parser whitelist
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
With the new checks in place, we can see we're doing things backwards,
so fix them up per the spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.
However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.
This should mean we get better bisectability in case of regression
due to the new irq handling.
v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not needed and further more will get in the way of a sane
locking scheme - psr_exit _can't_ take modeset locks due to lock
inversion, and at least once dp mst hits the connector list
is no longer static.
But since we track all state in dev_priv->psr there is no need
at all.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Any comment containing "current Intel hardware supports" quickly
becomes obsolete, so remove it and let people discover the information
by looking at the function implementation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two BSpec updates changed the recommended values for BDW eDP and DP
DDI buffer translations. Now the signal levels also match the HSW signal
levels, which simplify things a little bit.
It seems some DP sinks don't work properly without voltage level 0 and
pre-emphasis level 3, so this patch may fix some bugs on
panels/monitors that happen on BDW but not on HSW.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The perfect solution for psr_exit is the hardware tracking the changes and
doing the psr exit by itself. This scenario works for HSW and BDW with some
environments like Gnome and Wayland.
However there are many other scenarios that this isn't true. Mainly one right
now is KDE users on HSW and BDW with PSR on. User would miss many screen
updates. For instances any key typed could be seen only when mouse cursor is
moved. So this patch introduces the ability of trigger PSR exit on kernel side
on some common cases that.
Most of the cases are coverred by psr_exit at set_domain. The remaining cases
are coverred by triggering it at set_domain, busy_ioctl, sw_finish and
mark_busy.
The downside here might be reducing the residency time on the cases this
already work very wall like Gnome environment. But so far let's get focused
on fixinge issues sio PSR couild be used for everybody and we could even
get it enabled by default. Later we can add some alternatives to choose the
level of PSR efficiency over boot flag of even over crtc property.
v2: remove exit from connector_dpms. Daniel pointed this is the wrong way and
also this isn't needed for BDW and HSW anyway.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has a PSR per transcoder, where DDIA supports
link disable and link standby modes while other
transcoders only support link standby.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When link is in stand by and PSR exit is triggered by a primary or sprite
plane flip this mode allows only one single updated frame to be send to
display than get back to PSR immediately.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also do not cache aux info. That info could be related to another panel.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Being more conservative by enabling PSR only on psr_enable function.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's be more conservative and protect platforms that don't
support PSR from unecessary interactions.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Since
commit 2e82a72031
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jan 17 15:46:43 2014 +0200
drm/i915: don't disable DP port after a failed link training
and
commit 5d6a1116c6
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Jan 16 18:35:57 2014 +0200
drm/i915: don't disable the DP port if the link is lost
we no longer call intel_dp_link_down from generic DP code, but only
from the !HAS_DDI dp encoder functions. hsw/bdw have their own encoder
disabling callback in intel_ddi.c.
Hence the early return is no longer needed and the big comment just
confusing, so let's rip it out. To ensure what we don't accidentally
use this again on ddi encoders add a WARN_ON instead.
Spotted while reading through intel_dp.c
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV pipe C can driver only port D, and pipes A and B can drivbe only
ports B and C. Configure the crtc_mask appropriately to reflect that.
v2: Moar braces (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With all the preceding refactoring the dp mode_set callback only
computes a bit of state (all derived from the pipe config) and also
writes the eld. As long as we do that before we enable the audio bit
or depend upon the correct value in intel_dp->DP we'll be fine.
No other hw state is touched.
We therefore only need to check that clearing intel_dp->DP is save.
Which it is since when we re-enable we already mask out all the bits
the link training code sets. And we need to keep on doing that so that
the re-train loop walking over pre-emph/voltage-swing values still
works properly.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only ilk/snb/ivb need the port A pll setup, so move it to the
pre_enable hook for those platforms. We can savely do this since on
those platforms there's nothing that touches the hardware between the
encoder->mode_set and the encoder->pre_enable calls.
Also add a comment that port A is ilk+ only.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are certain BDW high res eDP machines that regressed due to
commit 38aecea0cc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 3 11:18:10 2014 +0100
drm/i915: reverse dp link param selection, prefer fast over wide again
The commit lead to 2 lanes at 5.4 Gbps being used instead of 4 lanes at
2.7 Gbps on the affected machines. Link training succeeded for both, but
the screen remained blank with the former config. Further investigation
showed that 4 lanes at 5.4 Gbps worked also.
The root cause for the blank screen using 2 lanes remains unknown, but
apparently the driver for a certain other operating system by default
uses the max available lanes. Follow suit on Broadwell eDP, for at least
until we figure out what is going on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76711
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming phy layer for CHV based on "Application note for 1273
CHV Display phy".
v2: Rebase the code and do some cleanup.
v3: Rework based on Ville review.
-Fix the macro where the ch info need to swap, and add parens to ?
operator.
-Fix wrong bit define for DPIO_PCS_SWING_CALC_0 and
DPIO_PCS_SWING_CALC_1 and rename for meaningful.
-Add some comments for CHV specific DPIO registers.
-Change the dp margin registery value to decimal to align with the
doc.
-Fix the not clearing some value in vlv_dpio_read before write again.
-Create new hdmi/dp encoder function for chv instead of share with
valleyview.
v4: Rebase the code after rename the DPIO registers define and upstream
change.
Based on Ville review.
-For unique transition scale selection, after Ville point out, look
like the doc might wrong for the bit 26. Use bit 27 for ch0 and
ch1.
-Break up some dpio write value into two/three steps for readability.
-Remove unrelated change.
-Add some shift define for some registers instead just give the hex
value.
-Fix a bug where write to wrong VLV_TX_DW3.
v5: Based on Ville review.
- Move tx lane latency optimal setting from chv_dp_pre_pll_enable to
chv_pre_enable_dp, and chv_hdmi_pre_pll_enable to
chv_hdmi_pre_enable respectively.
- Fix typo in one margin_reg_value for DP_TRAIN_VOLTAGE_SWING_400.
- Clear DPIO_TX_UNIQ_TRANS_SCALE_EN for DP and HDMI.
- Mask the old deemph and swing bits for hdmi.
v6: Remove stub for pre_pll_enable for dp and hdmi.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[vsyrjala: Don't touch panel power sequencing on DP]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the chv clock limit, find the best divisor.
The divisor data has been verified with this spreadsheet.
P1273_DPLL_Programming Spreadsheet.
v2: Rebase the code and change the chv_find_best_dpll based on new
standard way to use intel_PLL_is_valid. Besides, clean up some extra
variables.
v3: Ville suggest better fixed point for m2 calculation.
v4: -Add comment for the limit is compute using fast clock. (Ville)
-Don't pass the request clock to chv_clock, as the same function will
be use clock readout, which doens't have request clock. (Ville)
-Add and use DIV_ROUND_CLOSEST_ULL to consistent with other clock
calculation. (Ville)
-Fix the dp m2 after m2 has stored fixed point. (Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Avoid div-by-zero in chv_clock()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most likely the minimums for both should be enough for enabling the
native resolution on the eDP, and we'll end up using the predetermined
optimal link config for the panel.
v2: Add debug prints.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73539
Tested-by: Markus Blank-Burian <burian@muenster.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Even if the panel claims it can support 4 lanes, there's the
possibility that the HW can't, so consider this while selecting the
max lane count.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some platforms need additional power domains to be on in addition to the
device D0 state to access the panel registers.
Suggested by Daniel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76987
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't think this is necessary; at least it doesn't appear to be on my
BYT. Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Because the docs say ULX doesn't support it on HSW.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If I unplug the eDP monitor, the BIOS of my machine will enable the
VDD bit, then when the driver loads it will think VDD is enabled. It
will detect that the eDP is not enabled and return false from
intel_edp_init_connector. This will trigger a call to
edp_panel_vdd_off_sync(), which trigger a WARN saying that the
refcount of the power domain is less than zero.
The problem happens because the driver gets a refcount whenever it
enables the VDD bit, and puts the refcount whenever it disables the
VDD bit. But on this case, the BIOS enabled VDD, so all we do is to
call put() without calling get() first, so the code added is there to
make sure we always have the get() in case the BIOS enabled the bit.
This regression was introduced in
commit e9cb81a228
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Nov 21 13:47:23 2013 -0200
drm/i915: get a runtime PM reference when the panel VDD is on
v2: - Rebase
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
- Inherit/reuse firmwar framebuffers (for real this time) from Jesse, less
flicker for fastbooting.
- More flexible cloning for hdmi (Ville).
- Some PPGTT fixes from Ben.
- Ring init fixes from Naresh Kumar.
- set_cache_level regression fixes for the vma conversion from Ville&Chris.
- Conversion to the new dp aux helpers (Jani).
- Unification of runtime pm with pc8 support from Paulo, prep work for runtime
pm on other platforms than HSW.
- Larger cursor sizes (Sagar Kamble).
- Piles of improvements and fixes all over, as usual.
* tag 'drm-intel-next-2014-03-21' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Include a note about the dangers of I915_READ64/I915_WRITE64
drm/i915/sdvo: fix questionable return value check
drm/i915: Fix unsafe loop iteration over vma whilst unbinding them
drm/i915: Enabling 128x128 and 256x256 ARGB Cursor Support
drm/i915: Print how many objects are shared in per-process stats
drm/i915: Per-process stats work better when evaluated per-process
drm/i915: remove rps local variables
drm/i915: Remove extraneous MMIO for RPS
drm/i915: Rename and comment all the RPS *stuff*
drm/i915: Store the HW min frequency as min_freq
drm/i915: Fix coding style for RPS
drm/i915: Reorganize the overclock code
drm/i915: init pm.suspended earlier
drm/i915: update the PC8 and runtime PM documentation
drm/i915: rename __hsw_do_{en, dis}able_pc8
drm/i915: kill struct i915_package_c8
drm/i915: move pc8.irqs_disabled to pm.irqs_disabled
drm/i915: remove dev_priv->pc8.enabled
drm/i915: don't get/put PC8 when getting/putting power wells
drm/i915: make intel_aux_display_runtime_get get runtime PM, not PC8
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Split the post_disable hooks for DP to g4x and vlv variants. We'll
need another variant soon, so this should make it look a bit cleaner.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Besides D0 device state we need the proper power wells to be on on
some platforms, so get the port power domain reference instead of an RPM
reference.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTOOOnAAoJEHm+PkMAQRiGsBAH/2PAOL3TbOG6tEedxQrTwsr2
muRIRTVWawjT8/npbHupxGnAyAVdmdffBHpmCmcftKdKNryT3YZW8/JWoYc+WSlo
3vTDJHDOYAe6yCBjjhYwcu150THBQdOymOi5mbbclo0XWYG18jd3+abYprRH6SiD
XqNSzYqoiv91JHBAWKBIpo1cyRDuwoM7+jZ7gX41r2800EL7loY3e08cPDDNU6HA
CKaLXMwLwYTefE+Wnr+4UUr08NbNBbBUKLUSXVqKKIpd+MtbyhV1SnWzz8VQSkag
K/uzsnGnE7nrqoepMSx3nXxzOWxUSY2EMbwhEjaKK4xBq9C9pzv3sG/o2/IyopU=
=Nuom
-----END PGP SIGNATURE-----
Merge tag 'v3.14' into drm-intel-next-queued
Linux 3.14
The vt-d w/a merged late in 3.14-rc needs a bit of fine-tuning, hence
backmerge.
Conflicts:
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_dp.c
All trivial adjacent lines changed type conflicts, so trivial git
doesn't even show them in the merg commit.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent addition of locking checks in
commit 62ff94a549
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Thu Jan 23 22:18:47 2014 +0100
drm/crtc-helper: remove LOCKING from kerneldoc
drm_add_edid_modes started to WARN about the mode_config.mutex not
being held in the lvds and dp initialization code.
Now since this is init code locking is fairly redudant if it wouldn't
be for the drm core registering sysfs files a bit early. And the
locking WARNINGs nicely enforce that indeed all access to the mode
lists are properly protected. And a full audit shows that only i915
and gma500 touch the modes lists at init time.
Hence I've opted to wrap up this entire mode detection sequence for
fixed panels with the mode_config mutex for both lvds and edp outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent addition of locking checks in
commit 62ff94a549
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Thu Jan 23 22:18:47 2014 +0100
drm/crtc-helper: remove LOCKING from kerneldoc
drm_add_edid_modes started to WARN about the mode_config.mutex not
being held in the lvds and dp initialization code.
Now since this is init code locking is fairly redudant if it wouldn't
be for the drm core registering sysfs files a bit early. And the
locking WARNINGs nicely enforce that indeed all access to the mode
lists are properly protected. And a full audit shows that only i915
and gma500 touch the modes lists at init time.
Hence I've opted to wrap up this entire mode detection sequence for
fixed panels with the mode_config mutex for both lvds and edp outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/intel_dp.c
A bit a mess with reverts which differe in details between -fixes and
-next and some other unrelated shuffling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts
commit dff392dbd2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 6 17:32:41 2013 -0200
drm/i915: don't touch the VDD when disabling the panel
which didn't take into account
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
and
commit 35a38556d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Aug 12 22:17:14 2012 +0200
drm/i915: reorder edp disabling to fix ivb MacBook Air
Unsurprisingly, various MacBooks failed.
Effectively the same has already been done in drm-intel-next-queued.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74628
Tested-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a small follow-up fix to the series of eDP VDD back and forth
we've had recently. This is effectively a combined revert of three
commits:
commit 2c2894f698fffd8ff53e1e1d3834f9e1035b1f39
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:05:20 2014 -0300
drm/i915: properly disable the VDD when disabling the panel
commit b3064154df
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Tue Mar 4 00:42:44 2014 +0100
drm/i915: Don't just say it, actually force edp vdd
commit dff392dbd2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 6 17:32:41 2013 -0200
drm/i915: don't touch the VDD when disabling the panel
which shows that we're pretty close back to where we started
already. The first two were basically reverting the last, but missing
the WARN. Add that back. We also OCD the intel_ prefix back to
intel_edp_panel_vdd_on() which was lost somewhere in between. The circle
closes.
For future reference, "drm/i915: don't touch the VDD when disabling the
panel" failed to take into account
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
and
commit 35a38556d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Aug 12 22:17:14 2012 +0200
drm/i915: reorder edp disabling to fix ivb MacBook Air
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit b3064154df tried to revert commit
dff392dbd2, but wasn't complete, which
resulted in regressions on Haswell. So this commit should fix
b3064154df by undoing what it did and
providing an actual complete revert of
dff392dbd2.
Fixes regression introduced by:
commit b3064154df
Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Date: Tue Mar 4 00:42:44 2014 +0100
drm/i915: Don't just say it, actually force edp vdd
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The functionality remains largerly the same. The main difference is that
i2c-over-aux defer timeouts are increased to be safe for all use cases
instead of depending on DP device type and properties.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do a slight rearrangement of the switch to prep for follow-up.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Functionality remains largely the same as before.
Note that the retry loops and native reply handling all moved into the
core drm helper functions now.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix up the stray ; Rodrigo spotted in his review and add a
note to the commit message to answer Rodrigo's question in his review.]
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is prep work for conversion to generic drm i2c-over-aux helpers
where we won't have the function to do this at.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce _edp_panel_vdd_on() that returns true if the call enabled vdd,
and a matching disable is needed. Keep edp_panel_vdd_on() as a helper
for when it is expected the vdd is off.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/Makefile
Makefile cleanup in drm-intel-next conflicts with a build-fix to move
intel_opregion under CONFIG_ACPI.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.
For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.
Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the encoder is tied to its port, we need to make sure the power
domain for that port is on before reading out the encoder HW state.
Note that this also covers also all connector get_hw_state handlers,
since all those just call the corresponding encoder get_hw_state
handler, which checks - after this change - for all power domains
the connector needs.
v2:
- no change
v3:
- push down the power domain checks into the specific encoder
get_hw_state handlers (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The connector detect and get_mode handlers need to access the port
specific HW blocks to read the EDID etc. Get/put the port power domains
around these handlers.
v2:
- get port power domain for HDMI too (Ville)
- get port power domain for the DP,HDMI audio detect handlers (Jesse)
- Leave the intel_runtime_pm_get/put in the DP detect function in place.
Instead of just removing them, these should be moved to the appropriate
power_well enable/disable handlers. We can do this after Paulo's
'Merge PC8 with runtime PM, v2' patchset.
v3:
- rebased on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
| has a higher precedence than ?. Therefore, the calculation doesn't do
at all what you would expect. Thanks to Ken for convincing me that this
was indeed the issue. Send me back to C programmer school, please.
I'm sort of surprised PSR was continuing to work for people. It should
be broken IMO (and it was broken for me, but I had assumed it never
worked).
Regression from:
commit ed8546ac1f
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Mon Nov 4 22:45:05 2013 -0800
drm/i915/bdw: Support eDP PSR
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Kenneth Graunke <kenneth.w.graunke@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Reported-by: "Kumar, Kiran S" <kiran.s.kumar@intel.com>
Cc: stable@vger.kernel.org [v3.13+]
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... it's this time of the year again. Originally we've frobbed this to
fix up some regressions, but maybe our DP code improved sufficiently
now that we can dare to do again what the spec recommends.
This reverts
commit 2514bc510d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 21 15:13:50 2012 -0700
drm/i915: prefer wide & slow to fast & narrow in DP configs
I'm pretty sure I'll regret this patch, but otoh I expect we won't
make progress here without poking the devil occasionally.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73694
Cc: peter@colberg.org
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Itai BEN YAACOV <candeb@free.fr>
Tested-by: David En <d.engraf@arcor.de>
Reported-and-Tested-by: Marcus Bergner <marcusbergner@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes the blank screen bug introduced in 3.14-rc1 on the
MacBook Air 6,2. The comments state that we need to force edp vdd so
lets put it back.
The regression was introduced by the following commit:
commit dff392dbd2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Dec 6 17:32:41 2013 -0200
drm/i915: don't touch the VDD when disabling the panel
v2: Wrap intel_disable_dp() with _vdd_on and _vdd_off
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74628
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Fix the execbuf rebind performance regression due to topic/ppgtt (Chris).
- Fix up the connector cleanup ordering for sdvod i2c and dp aux devices (Imre).
- Try to preserve the firmware modeset config on driver load. And a bit of prep
work for smooth takeover of the fb contents (Jesse).
- Prep cleanup for larger gtt address spaces on bdw (Ben).
- Improve our vblank_wait code to make hsw modesets faster (Paulo).
- Display debugfs file (Jesse).
- DRRS prep work from Vandana Kannan.
- pipestat interrupt handler to fix a few races around vblank/pageflip handling
on byt (Imre).
- Improve display fuse handling for display-less SKUs (Damien).
- Drop locks while stalling for the gpu when serving pagefaults to improve
interactivity (Chris).
- And as usual piles of other improvements and small fixes all over.
* tag 'drm-intel-next-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel: (65 commits)
drm/i915: fix NULL deref in the load detect code
drm/i915: Only bind each object rather than for every execbuffer
drm/i915: Directly return the vma from bind_to_vm
drm/i915: Simplify i915_gem_object_ggtt_unpin
drm/i915: Allow blocking in the PDE alloc when running low on gtt space
drm/i915: Don't allocate context pages as mappable
drm/i915: Handle set_cache_level errors in the status page setup
drm/i915: Don't pin the status page as mappable
drm/i915: Don't set PIN_MAPPABLE for legacy ringbuffers
drm/i915: Handle set_cache_level errors in the pipe control scratch setup
drm/i915: split PIN_GLOBAL out from PIN_MAPPABLE
drm/i915: Consolidate binding parameters into flags
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
drm/i915: sdvo: fix error path in sdvo_connector_init
drm/i915: dp: fix order of dp aux i2c device cleanup
drm/i915: add unregister callback to connector
drm/i915: don't reference null pointer at i915_sink_crc
drm/i915/lvds: Remove dead code from failing case
drm/i915: don't preserve inherited configs with nothing on v2
drm/i915/bdw: Split up PPGTT cleanup
...
- Yet more steps towards atomic modeset from Ville.
- DP panel power sequencing improvements from Paulo.
- irq code cleanups from Ville.
- 5.4 GHz dp lane clock support for bdw/hsw from Todd.
- Clock readout support for hsw/bdw (aka fastboot) from Jesse.
- Make pipe underruns report at ERROR level (Ville). This is to check our
improved watermarks code.
- Full ppgtt support from Ben for gen7.
- More fbc fixes and improvements from Ville all over the place, unfortunately
not yet enabled by default on more platforms.
- w/a cleanups from Ville.
- HiZ stall optimization settings (Chia-I Wu).
- Display register mmio offset refactor patch from Antti.
- RPS improvements for corner-cases from Jeff McGee.
* tag 'drm-intel-next-2014-02-07' of ssh://git.freedesktop.org/git/drm-intel: (166 commits)
drm/i915: Update rps interrupt limits
drm/i915: Restore rps/rc6 on reset
drm/i915: Prevent recursion by retiring requests when the ring is full
drm/i915: Generate a hang error code
drm/i915: unify FLIP_DONE macro names
drm/i915: vlv: s/spin_lock_irqsave/spin_lock/ in irq handler
drm/i915: factor out valleyview_pipestat_irq_handler
drm/i915: vlv: don't unmask IIR[DISPLAY_PIPE_A/B_VBLANK] interrupt
drm/i915: Reorganize display pipe register accesses
drm/i915: Treat using a purged buffer as a source of EFAULT
drm/i915: Convert EFAULT into a silent SIGBUS
drm/i915: release mutex in i915_gem_init()'s error path
drm/i915: check for oom when allocating private_default_ctx
drm/i915/vlv: WA to fix Voltage not getting dropped to Vmin when Gfx is power gated.
drm/i915: Get rid of acthd based guilty batch search
drm/i915: Use hangcheck score to find guilty context
drm/i915: Drop WaDisablePSDDualDispatchEnable:ivb for IVB GT2
drm/i915: Fix IVB GT2 WaDisableDopClockGating and WaDisablePSDDualDispatchEnable
drm/i915: Don't access snooped pages through the GTT (even for error capture)
drm/i915: Only print information for filing bug reports once
...
Conflicts:
drivers/gpu/drm/i915/intel_dp.c
Atm we set the parent of the dp i2c device to be the correspondig
connector device. During driver cleanup we first remove the connector
device through intel_modeset_cleanup()->drm_sysfs_connector_remove() and
only after that the i2c device through the encoder's destroy callback.
This order is not supported by the device core and we'll get a warning,
see the below bugzilla ticket. The proper order is to remove first any
child device and only then the parent device.
The first part of the fix changes the i2c device's parent to be the drm
device. Its logical owner is not the connector anyway, but the encoder.
Since the encoder doesn't have a device object, the next best choice is
the drm device. This is the same what we do in the case of the sdvo i2c
device and what the nouveau driver does.
The second part creates a symlink in the connector's sysfs directory
pointing to the i2c device. This is so, that we keep the current ABI,
which also makes sense in case someone wants to look up the i2c device
belonging to a specific connector.
Reference: http://lists.freedesktop.org/archives/intel-gfx/2014-January/038782.html
Reference: http://lists.freedesktop.org/archives/intel-gfx/2014-February/039427.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70523
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit d9255d5714
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 26 20:05:59 2013 -0300
it became clear that we need to separate the unload sequence into two
parts:
1. remove all interfaces through which new operations on some object
(crtc, encoder, connector) can be started and make sure all pending
operations are completed
2. do the actual tear down of the internal representation of the above
objects
The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.
Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Retrying indefinitely places too much trust on the aux implementation of
the sink devices.
Reported-by: Daniel Martin <consume.noise@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71267
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Tested-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Sree Harsha Totakura <freedesktop@h.totakura.in>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Give more slack to sink devices before retrying on native aux
defer. AFAICT the 100 us timeout was not based on the DP spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org (on Jani's request)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of modifying intel_panel in lvds_init_connector/dsi_init/
edp_init_connector, making changes to move intel_panel->downclock_mode
initialization to intel_panel_init()
v2: Jani's review comments incorporated
Removed downclock_mode local variable in dsi_init and
edp_init_connector
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently it's broken in the exact same way as the gmbus irq. For
reference of the full story see
commit c12aba5aa0
Author: Jiri Kosina <jkosina@suse.cz>
Date: Tue Mar 19 09:56:57 2013 +0100
drm/i915: stop using GMBUS IRQs on Gen4 chips
The effect is that we have a storm of unclaimed interrupts on the
legacy irq line. If that one is used by a different device then the
kernel will complain and rather quickly kill the irq source. Which
breaks any device trying to actually use the legacy irq line.
This regression has been introduced
commit 4aeebd7443
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 31 09:53:36 2013 +0100
drm/i915: dp aux irq support for g4x/vlv
Note that disabling MSI works around the issue, but we can't do that
since apparently then the hw will miss interrupts. At least if
relevant comments in i915_irq.c are accurate.
v2: Cross-reference dp aux and gmbus gen4 comments.
v3: Consolidate harder into i915_drv.h as suggested by Chris.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we setup the HW panel power sequencer logic both for eDP and DP
ports. On eDP we then go on and start the power on sequence and commence
with link training when it's ready. On DP we don't do the power on
sequencing but do the link training immediately. At this point the DP
PHY block gets stuck, since - supposedly - it is waiting for the power
on sequence to finish. The actual register write that seems to hold off
the PHY is PIPEX_PP_ON_DELAYS[Panel Control Port Select]. Writing here
a non-0 value eventually sets PIPEX_PP_STATUS[Require Asset Status] to
1 and blocks the PHY until the panel power on is ready.
Fix this by not doing any PP sequencing setup for DP ports.
Thanks to Ville Syrjälä, Jesse Barnes and Todd Previte for the help in
tracking this down.
Note that on older gmch platforms (where we have lvds instead of edp)
we've hacked around this by writing the magic ABCD unlock key to PP
registers, which disables the hw sanity checks.
For edp all platforms thus far had the pch split, with the edp port in
the north display complex and the PP registers on the pch the hw
sanity checks (expressed through the "Require Asset Status" bit) was
never functional, hence never a real issue.
This regression has been introduce in
commit bf13e81b90
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about the bigger story here.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The initial jiffies value can be non-0, so set the inital panel power
sequencer timestamps accordingly. This didn't cause a problem on 64 bit
machines but on 32 bit jiffies is initially -300*HZ, so if the panel
power is initally off in the call from edp_panel_vdd_on()->
wait_panel_power_cycle() we'd wait up to ~300 sec more than needed.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This debugfs interface will allow intel-gpu-tools test case
to verify if screen has been updated properly on cases like PSR.
v2: Accepted all Daniel's suggestions:
* grab modeset lock
* loop over connector and check DPMS on
* return errors
* use _eDP1 suffix for easy future extension
* don't cache crc_supported neither latest crc
* return crc as a full array and read it at once with aux.
* use 0 to turn TEST_SINK off.
* split the drm_helpers definitions in another patch.
v3: Accepted 2 Damien's suggestion: remove h from printf hexa
and return ENODEV when eDP not present instead of EAGAIN.
v4: Accepted 2 Jani' s suggestion: 1 path for unlock and remove
_retry from aux read.
v5: removing last missing useless _retry (by Damien)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a bit more flexibility here in the future, bits get shuffled
around.
v2: more descriptive commit message (Jani Nikula)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So it's easier to compare what we program with the documentation, not
having to jump at all.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also, move that computation outside of the for loop that tries 5 times,
this value doesn't change between tries.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A tiny clean-up to allow better code separation between platforms.
v2: Fix comment placement (put in in i9xx_get_aux_clock_divider()) and
nuke the outdated PCH eDP comment (Jani Nikula)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For HSW+ platforms, enable the 5.4Ghz (HBR2) link rate for devices that support it. The
sink device must report that is supports Displayport 1.2 and the HBR2 bit rate in the
DPCD in order to use HBR2.
Signed-off-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already do the wait in software: see
ironlake_wait_backlight_on and ironlake_edp_wait_backlight_off.
For the "backlight on" delay, even BSpec says we need to program 0x1
to PP_ON_DELAYS 12:0.
For the "backlight off" delay, if we don't do the same thing, when we
call ironlake_wait_panel_off we'll end up waiting for the it again.
On my machine the off delay is 200ms, so we save this amount of time
whenever we disable the panel (e.g, suspend).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Function ironlake_wait_panel_off should just wait for the power off
delay, while function ironlake_wait_panel_power_cycle should wait for
the panel cycle (that's required after we turn the panel off, before
we enable it again).
The problem is that, currently, ironlake_wait_panel_off is waiting not
just for the panel to be off, but also for the power cycle delay and
the backlight off delay. This function relies on the PP_STATUS bits
3:0, which are not documented and not supposed to be used. A quick
analysis of the values we get while waiting quickly shows that power
off is reached while bits 3:0 are still 0x1, and the time it takes to
become 0x0 is the power cycle delay.
On my system with backlight off delay of 200ms, power down delay of
50ms and power cycle delay of 500ms, this is what I get:
- Start waiting with value 0x80000008, timestamp 6.429364.
- Jumps to 0xa0000003, timestamp 6.431360 (time waited: 0.001996)
- Jumps to 0xa0000002, timestamp 6.631277 (time waited: 0.201913)
- Jumps to 0x08000001, timestamp 6.681258 (time waited: 0.251894)
- Jumps to 0x00000000, timestamp 7.192012 (time waited: 0.762648)
As you can see, ironlake_wait_panel_off is sleeping 760ms instead of
the expected 50ms: the first 200ms matches the backlight off delay
(which we should already have waited for!), then the 50ms for the real
panel off delay, then the 500ms for the panel power cycle.
This patch makes is look just at bits 31 and 29:28, which will ignore
the panel power cycle.
And just to be clear: this saves 500ms on my system every time we
disable the panel. But we can still save 200ms more (the backlight off
delay) on the next patches.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I like how the macros are nicely column-aligned, so we can properly
compare what each macro waits for, but a column full of zeroes doesn't
really help anything: it just makes the lines bigger, and they're
already way past 80 columns. I imagine this column was used in the
past, but IMHO now we can get rid of it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They now also work on vlv, which has the regs somewhere else. And
daring a glance into the looking glass it seems like this
functionality will continue to work the same for the next few hardware
platforms.
So it's better to just remove that misleading prefix and have a bit
shorter code for better readability.
The only exceptions are the panel/backlight functions shared with
intel_ddi.c, those get an intel_ prefix.
While at it make the vdd_on/off functions static.
And one straggler was missing the edp_ in the name, so make everything
neatly OCD.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The eDP spec defines some points where after you do action A, you have
to wait some time before action B. The thing is that in our driver
action B does not happen exactly after action A, but we still use
msleep() calls directly. What this patch does is that we record the
timestamp of when action A happened, then, just before action B, we
look at how much time has passed and only sleep the remaining amount
needed.
With this change, I am able to save about 5-20ms (out of the total
200ms) of the backlight_off delay and completely skip the 1ms
backlight_on delay. The 600ms vdd_off delay doesn't happen during
normal usage anymore due to a previous patch.
v2: - Rename ironlake_wait_jiffies_delay to intel_wait_until_after and
move it to intel_display.c
- Fix the msleep call: diff is in jiffies
v3: - Use "tmp_jiffies" so we don't need to worry about the value of
"jiffies" advancing while we're doing the math.
v4: - Rename function again.
- Move function to i915_drv.h.
- Store last_power_cycle at edp_panel_off too.
- Use msecs_to_jiffies_timeout, then replace the msleep with an
open-coded version that avoids the extra +1 jiffy.
- Try to add units to every variable name so we don't confuse
jiffies with milliseconds.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our driver has two different ways of waiting for panel power
sequencing delays. One of these ways is through
ironlake_wait_panel_status, which implicitly uses the values written
to our registers. The other way is through the functions that call
intel_wait_until_after, and on this case we do direct msleep() calls
on the intel_dp->xxx_delay variables.
Function intel_dp_init_panel_power_sequencer is responsible for
initializing the _delay variables and deciding which values we need to
write to the registers, but it does not write these values to the
registers. Only at intel_dp_init_panel_power_sequencer_registers we
actually do this write.
Then problem is that when we call intel_dp_i2c_init, we will get some
I2C calls, which will trigger a VDD enable, which will make use of the
panel power sequencing registers and the _delay variables, so we need
to have both ready by this time. Today, when this happens, the _delay
variables are zero (because they were not computed) and the panel
power sequence registers contain whatever values were written by the
BIOS (which are usually correct).
What this patch does is to make sure that function
intel_dp_init_panel_power_sequencer is called earlier, so by the time
we call intel_dp_i2c_init, the _delay variables will already be
initialized. The actual registers won't contain their final values,
but at least they will contain the values set by the BIOS.
The good side is that we were reading the values, but were not using
them for anything (because we were just skipping the msleep(0) calls),
so this "fix" shouldn't fix any real existing bugs. I was only able to
identify the problem because I added some debug code to check how much
time time we were saving with my previous patch.
Regression introduced by:
commit ed92f0b239
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Wed Jun 12 17:27:24 2013 -0300
drm/i915: extract intel_edp_init_connector
v2: - Rewrite commit message.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm after a failed link training we disable the DP port. This can happen
during a modeset-enable or a DP link re-establishment. The latter can be
a problem and we shouldn't disable the DP port, see the previous patch for
the reasoning. In the former case the right thing would be to disable
the DP port, but also the rest of the pipe.
As a stop-gap solution leave the DP port enabled in both cases. It is an
improvement on its own (avoiding HW lock ups) and the proper solution
for the first case requires a bigger change, so let's keep that on the
TODO list.
v2:
- fix explanation of change impact (Chris)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently if the DP link is lost (either because of a hot unplug, or
failed link status check) we disable the DP port, but leave the rest
of the pipe running. This is incompatible with the modeset disabling
sequence of some platforms/configurations. At least this is the case for
DP ports on the CPU as opposed to PCH.
Atm we'll also get a warning when we do a modeset disable after the
above link lost event, since we expect the DP port to be enabled at this
point (see the bugzilla ticket for the related dmesg).
Note that with this patch we'll still end up disabling the port, thanks
to the HPD uevent and subsequent modeset disable.
See also the next patch fixing the other half of this issue.
Solution suggested by Ville.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70570
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fbc1 improvements from Ville (pre-gm45).
- vlv forcewake improvements from Deepak S.
- Some corner-cases fixes from Mika for the context hang stat code.
- pc8 improvements and prep work for runtime D3 from Paulo, almost ready for
primetime.
- gen2 dpll fixes from Ville.
- DSI improvements from Shobhit Kumar.
- A few smaller fixes and improvements all over.
[airlied: intel_ddi.c conflict fixed up]
* tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel: (61 commits)
drm/i915/bdw: Implement ff workarounds
drm/i915/bdw: Force all Data Cache Data Port access to be Non-Coherent
drm/i915/bdw: Don't use forcewake needlessly
drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
drm/i915: dont call irq_put when irq test is on
drm/i915: Rework the FBC interval/stall stuff a bit
drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
drm/i915: FBC_CONTROL2 is gen4 only
drm/i915: Gen2 FBC1 CFB pitch wants 32B units
drm/i915: split intel_ddi_pll_mode_set in 2 pieces
drm/i915: Fix timeout with missed interrupts in __wait_seqno
drm/i915: touch VGA MSR after we enable the power well
drm/i915: extract hsw_power_well_post_{enable, disable}
drm/i915: remove i915_disable_vga_mem declaration
drm/i915: Parametrize the dphy and other spec specific parameters
drm/i915: Remove redundant DSI PLL enabling
drm/i915: Reorganize the DSI enable/disable sequence
drm/i915: Try harder to get best m, n, p values with minimal error
drm/i915: Compute dsi_clk from pixel clock
drm/i915: Use FLISDSI interface for band gap reset
...
Conflicts:
drivers/gpu/drm/i915/intel_ddi.c
The current values seem to be defined in a format that's specific to the
i915, gma500 and radeon drivers. To make this more generally useful, use
the values as defined in the specification.
While at it, prefix the constants with DP_ for improved namespacing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- some more ppgtt prep patches from Ben
- a few fbc fixes from Ville
- power well rework from Imre
- vlv forcewake improvements from Deepak S, Ville and Jesse
- a few smaller things all over
[airlied: fixup forwcewake conflict]
* tag 'drm-intel-next-2013-11-29' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: Fix port name in vlv_wait_port_ready() timeout warning
drm/i915: Return a drm_mode_status enum in the mode_valid vfuncs
drm/i915: add intel_display_power_enabled_sw() for use in atomic ctx
drm/i915: drop DRM_ERROR in intel_fbdev init
drm/i915/vlv: use parallel context restore when coming out of RC6
drm/i915/vlv: use a lower RC6 timeout on VLV
drm/i915/sdvo: Fix up debug output to not split lines
drm/i915: make sparse happy for the new vlv mmio read function
drm/i915: drop the right force-wake engine in the vlv mmio funcs
drm/i915: Fix GT wake FIFO free entries for VLV
drm/i915: Report all GTFIFODBG errors
drm/i915: Enabling DebugFS for valleyview forcewake counts
drm/i915/vlv: Valleyview support for forcewake Individual power wells.
drm/i915: Add power well arguments to force wake routines.
drm/i915: Do not attempt to re-enable an unconnected primary plane
drm/i915: add a debugfs entry for power domain info
drm/i915: add a default always-on power well
drm/i915: don't do BDW/HSW specific powerdomains init on other platforms
drm/i915: protect HSW power well check with IS_HASWELL in redisable_vga
drm/i915: use IS_HASWELL/BROADWELL instead of HAS_POWER_WELL
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
If we're disabling the VDD override bit and the panel is enabled, we
don't need to wait for anything. If the panel is disabled, then we
need to actually wait for panel_power_cycle_delay, not
panel_power_down_delay, because the power down delay was already
respected when we disabled the panel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't see a reason to touch VDD when we're disabling the panel:
since the panel is enabled, we don't need VDD. This saves a few sleep
calls from the vdd_on and vdd_off functions at every modeset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69693
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix the patch mangle wiggle has done ... Spotted by Paulo.
Also drop the runtime_pm_put call which now has to go due to different
patch ordering. Also from Paul.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put it when it's off. Otherwise, when you run pm_pc8 from
intel-gpu-tools, and the delayed function that disables VDD runs,
we'll get some messages saying we're touching registers while the HW
is suspended.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are needed when we cat the debugfs and sysfs files.
V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When inspecting reports that boot/suspend/resume times are unusual it
would be useful to clearly identify the time we must spend waiting for
the hardware to complete its task. In this case we have a notification
before we start waiting for the panel to change state, but none
afterwards - which would be useful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had some mode_valid() vfuncs returning an int, others the enum. Let's
use the latter everywhere.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reduce the eDP detection to just checking if it's port A, or if
the VBT tells us that the port is eDP for the other ports.
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV can have eDP on either port B or C, or even both. Based on the
VBT spec, intel_dpd_is_edp() should work on VLV too, assuming we
check the correct ports.
So instead of hardcoding port D, rename the function to
intel_dp_is_edp() and pass the port as a parameter, and use it
on VLV ports B and C.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Wrestle the patch to apply and compile properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we have this everywhere. Next up would be to wire up the DP
hotplug pin to speed up panel power sequencing for eDP panels ...
I've decided to leave the has_aux_irq logic in the code, it should
come handy for hw bringup.
For testing/fail-safety the dp aux code already has a timeout when
waiting for interrupts to signal completion and screams rather loud if
they don't arrive in time. Given that we need a real piece of hw to
talk to anyway this is probably as good as it gets.
v2: Don't check the dp aux channel bits on i965 machines, they have a
different meaning there. Yay for reusing bits at will! Spotted by
Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We used to put the local sink and any downstream sinks to power down
mode at disable or dpms off using the DPCD SET_POWER register, until
this was broken by
commit e8cb455876
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 1 13:05:48 2012 +0200
drm/i915/dp: convert to encoder disable/enable
Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not the same as the Haswell ones.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the bits in the VBT child device type have some speciifc meaning,
so looking for an exact match isn't always the right thing. On some
VLVs for example the device type for eDP panels is 0x1806.
If we mask out the bits that could concievably change between different
eDP panels, we are left with the set of bits that should still
tell us if the port is eDP or not.
v2: Use the named bits for VBT child device type
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That explains why I was seeing 2 consecutive "Turning eDP VDD off"
messages.
Regression introduced by:
commit bf13e81b90
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 6 07:40:05 2013 +0300
drm/i915: add support for per-pipe power sequencing on vlv
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we only print messages when we actually enable VDD and when we
actually disable VDD.
The changes in the last commit triggered a big number of messages
while the driver was being initialized, and I thought we were toggling
things on/off too many times, but that was not really true: we were
just being too verbose.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the eDP output is disabled, then we try to use /dev/i2c-X file to
do i2c transations, we get a WARN from intel_dp_check_edp() saying
we're trying to do AUX communication with the panel off. So this
commit reorganizes the code so we enable the VDD at
intel_dp_i2c_aux_ch() instead of just the callers inside i915.ko.
This fixes the i2c subtest from the pc8 test of intel-gpu-tools on
machines that have eDP panels.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This isn't a real fix to the problem, but rather a stopgap measure while
trying to find a proper solution.
There are several laptops out there that fail to light up the eDP panel
in UEFI boot mode. They seem to be mostly IVB machines, including but
apparently not limited to Dell XPS 13, Asus TX300, Asus UX31A, Asus
UX32VD, Acer Aspire S7. They seem to work in CSM or legacy boot.
The difference between UEFI and CSM is that the BIOS provides a
different VBT to the kernel. The UEFI VBT typically specifies 18 bpp and
1.62 GHz link for eDP, while CSM VBT has 24 bpp and 2.7 GHz link. We end
up clamping to 18 bpp in UEFI mode, which we can fit in the 1.62 Ghz
link, and for reasons yet unknown fail to light up the panel.
Dithering from 24 to 18 bpp itself seems to work; if we use 18 bpp with
2.7 GHz link, the eDP panel lights up. So essentially this is a link
speed issue, and *not* a bpp clamping issue.
The bug raised its head since
commit 657445fe86
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat May 4 10:09:18 2013 +0200
Revert "drm/i915: revert eDP bpp clamping code changes"
which started clamping bpp *before* computing the link requirements, and
thus affecting the required bandwidth. Clamping after the computations
kept the link at 2.7 GHz.
Even though the BIOS tells us to use 18 bpp through the VBT, it happily
boots up at 24 bpp and 2.7 GHz itself! Use this information to
selectively ignore the VBT provided value.
We can't ignore the VBT eDP bpp altogether, as there are other laptops
that do require the clamping to be used due to EDID reporting higher bpp
than the panel can support.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59841
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67950
Tested-by: Ulf Winkelvos <ulf@winkelvos.de>
Tested-by: jkp <jkp@iki.fi>
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is useful with the follow-up patch that frobs
dev_priv->vbt.edp_bpp, and the value no longer comes directly from
VBT.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP spec allows this, and requires it when full link training is
started with non-minimum voltage swing and/or non-zero pre-emphasis.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If channel equalization succeeds, there's no indication something went
wrong in clock recovery (unless debug is enabled). We should shout about
the failures and fix them instead of hiding them under the carpet.
This has allowed bugs like [1] stay dormant for a long time.
[1] https://bugs.freedesktop.org/show_bug.cgi?id=70117
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
for igt test case.
v2: remove trailing spaces and fix conflicts
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet:
- make it comipile
- s/IS_HASWELL/HAS_PSR/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power Well in use forces constantly PSR to exit.
On recent Kernel I noticed that PSR Performance Counter was always 0
indicating that PSR was never really achieved.
By masking LPSP, PSR can work normally and save power on Haswell.
Two bugs had been raised with PSR flag enabled:
- "Screen flickers when booted by enabling PSR in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
- "When booting the DUT with PSR feature enabled in the kernel (i915.enable_psr=1) , the system is booting to a gray screen."
Both bugs has been fixed by this patch.
v2: proper comment for -fixes
Tested-by: Selvaraj, Elavarasan <elavarasanx.selvaraj@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Neither the DP spec nor the compliance test spec state or imply that we
should write the DP_TRAINING_PATTERN_SET at every voltage swing and
pre-emphasis change. Indeed we probably shouldn't. So don't.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Smoke-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per DP1.2 spec.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the typo in previous commit for DP 1.62 divisor.
drm/i915: Move Valleyview DP DPLL divisor calc to intel_dp_set_clock v2
v2: sigh, the m1 div is 3.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future generations will be changing these registers (thanks to design
for giving us an early heads up). To help abstract, create the
definition of the base of the register block, and define all registers
relative to that.
Design has promised to not change the offsets relative to the base.
v2: Also change IS_HASWELL checks to HAS_PSR
CC: Rodrigo Vivi <rodrigo.vivi@gmail.com>
CC: Intel GFX <intel-gfx@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reduce AUX transactions for non-eDP.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently treat the child_device_config as a simple struct, but
this is not correct: new BDB versions change the meaning of some
offsets, so the struct needs to be adjusted for each version.
Since there are too many changes (today we're in version 170!), making
a big versioned union would be too complicated, so child_device_config
is now a union of 3 things: (i) a "raw" byte array that's safe to use
anywhere; (ii) an "old" structure that's the one we've been using and
should be safe to keep in the SDVO and TV code; and (iii) a "common"
structure that should contain only fields that are common for all the
known VBT versions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We haven't read the downstream port caps for DPCD 1.0, so don't use
them.
v2: use defines for DPCD 1.0 downstream port types
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2013-09-21:
- clock state handling rework from Ville
- l3 parity handling fixes for hsw from Ben
- some more watermark improvements from Ville
- ban badly behaved context from Mika
- a few vlv improvements from Jesse
- VGA power domain handling from Ville
drm-intel-next-2013-09-06:
- Basic mipi dsi support from Jani. Not yet converted over to drm_bridge
since that was too fresh, but the porting is in progress already.
- More vma patches from Ben, this time the code to convert the execbuffer
code. Now that the shrinker recursion bug is tracked down we can move
ahead here again. Yay!
- Optimize hw context switching to not generate needless interrupts (Chris
Wilson). Also some shuffling for the oustanding request allocation.
- Opregion support for SWSCI, although not yet fully wired up (we need a
bit of runtime D3 support for that apparently, due to Windows design
deficiencies), from Jani Nikula.
- A few smaller changes all over.
[airlied: merge conflict fix in i9xx_set_pipeconf]
* tag 'drm-intel-next-2013-09-21-merged' of git://people.freedesktop.org/~danvet/drm-intel: (119 commits)
drm/i915: assume all GM45 Acer laptops use inverted backlight PWM
drm/i915: cleanup a min_t() cast
drm/i915: Pull intel_init_power_well() out of intel_modeset_init_hw()
drm/i915: Add POWER_DOMAIN_VGA
drm/i915: Refactor power well refcount inc/dec operations
drm/i915: Add intel_display_power_{get, put} to request power for specific domains
drm/i915: Change i915_request power well handling
drm/i915: POSTING_READ IPS_CTL before waiting for the vblank
drm/i915: don't disable ERR_INT on the IRQ handler
drm/i915/vlv: disable rc6p and rc6pp residency reporting on BYT
drm/i915/vlv: honor i915_enable_rc6 boot param on VLV
drm/i915: s/HAS_L3_GPU_CACHE/HAS_L3_DPF
drm/i915: Do remaps for all contexts
drm/i915: Keep a list of all contexts
drm/i915: Make l3 remapping use the ring
drm/i915: Add second slice l3 remapping
drm/i915: Fix HSW parity test
drm/i915: dump crtc timings from the pipe config
drm/i915: register backlight device also when backlight class is a module
drm/i915: write D_COMP using the mailbox
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
There is no clear cut rules or specs for the retry interval, as there
are many factors that affect overall response time. Increase the
interval, and even more so on branch devices which may have limited i2c
bit rates.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=60263
Tested-by: Nicolas Suzor <nic@suzor.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we control everything and nothing exceeds the current limits,
but (i) we never think about these limits when reviewing patches, (ii)
not all the callers check the return values and (iii) if we ever hit
any of these messages, we'll have to fix the code that added the bad
message.
The current limit for these messages is 20 since we only have 5 data
registers on all the current gens.
The checks inside intel_dp_aux_native_{write,read} are to prevent
buffer overflows. The check inside intel_dp_aux_ch is to prevent
writing past our 5 data registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_edp_psr_match_conditions() currently looks at crtc->mode
when it really needs to look at adjusted_mode. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV has per-pipe PP registers. Set up power sequencing on mode set. The
connector init time setup is problematic, since we don't have a pipe at
that time. Cook up something.
v2:
- use vlv_power_sequencer_pipe() also in _pp_{ctrl,stat}_reg()
- use PANEL_PORT_SELECT_DPC_VLV (Ville)
v3: make checkpatch happier
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Make checkpatch a bit more happier still ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove duplicates, add VLV specific macros for port B and C.
v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow-up to
commit 5004945f1d
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jul 30 12:20:32 2013 +0300
drm/i915: move encoder->enable callback later in VLV crtc enable
v2: Rebase on the renamed enable hooks, adding clarity (Ville)
Reference: http://mid.gmane.org/CAKMK7uFs9EMvMW8BnS24e5UNm1D7JrfVg3SD5SDFtVEamGfOOg@mail.gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In line with the rest of the code base. No functional changes.
v2: also s/intel_pre_enable_dp/g4x_pre_enable_dp/ for consistency (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DP pll settings, there is only two golden configs. Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.
v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP 1.4 supports 4-5 extra link rates in additional to current 2 link
rate. Create a structure to store the DPLL divisor data to improve
readability.
v2: Fix the gen4_dpll/pch_dpll initialization to C99
designated initializers, and use a single loop for all platforms. (Jani and Daniel)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch allows PC8+ states on Haswell. These states can only be
reached when all the display outputs are disabled, and they allow some
more power savings.
The fact that the graphics device is allowing PC8+ doesn't mean that
the machine will actually enter PC8+: all the other devices also need
to allow PC8+.
For now this option is disabled by default. You need i915.allow_pc8=1
if you want it.
This patch adds a big comment inside i915_drv.h explaining how it
works and how it tracks things. Read it.
v2: (this is not really v2, many previous versions were already sent,
but they had different names)
- Use the new functions to enable/disable GTIMR and GEN6_PMIMR
- Rename almost all variables and functions to names suggested by
Chris
- More WARNs on the IRQ handling code
- Also disable PC8 when there's GPU work to do (thanks to Ben for
the help on this), so apps can run caster
- Enable PC8 on a delayed work function that is delayed for 5
seconds. This makes sure we only enable PC8+ if we're really
idle
- Make sure we're not in PC8+ when suspending
v3: - WARN if IRQs are disabled on __wait_seqno
- Replace some DRM_ERRORs with WARNs
- Fix calls to restore GT and PM interrupts
- Use intel_mark_busy instead of intel_ring_advance to disable PC8
v4: - Use the force_wake, Luke!
v5: - Remove the "IIR is not zero" WARNs
- Move the force_wake chunk to its own patch
- Only restore what's missing from RC6, not everything
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caught by "make W=1 drivers/gpu/drm/i915/".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV wants encoder enabling before the pipe is up. This is currently
achieved through calling the ->enable callback early, right after the
->pre_enable callback, in valleyview_crtc_enable(). This loses both the
distinction between ->pre_enable and ->enable on VLV and the possibility
to use a hook at the end of the modeset sequence.
Rearrange the DP callbacks to make it possible to move ->enable call
later. Basically do everything in ->pre_enable on VLV, and make ->enable
a NOP.
There should be no functional changes.
v2: Rebase.
v3: Explain why this is needed in the commit message (Chris).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we get flooded by the kernel warning us that we are doing
long sequences of IO without serialisation. For example,
WARNING: CPU: 0 PID: 11136 at drivers/gpu/drm/i915/intel_sideband.c:40 vlv_sideband_rw+0x48/0x1ef()
Modules linked in:
CPU: 0 PID: 11136 Comm: kworker/u2:0 Tainted: G W 3.11.0-rc2+ #4
Call Trace:
[<c2028564>] ? warn_slowpath_common+0x63/0x78
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c20285dd>] ? warn_slowpath_null+0xf/0x13
[<c227ad43>] ? vlv_sideband_rw+0x48/0x1ef
[<c227b060>] ? vlv_dpio_write+0x1c/0x21
[<c2262b3b>] ? intel_dp_set_signal_levels+0x24a/0x385
[<c2264909>] ? intel_dp_complete_link_train+0x25/0x1d1
[<c2264c55>] ? intel_dp_check_link_status+0xf7/0x106
[<c2238ced>] ? i915_hotplug_work_func+0x17b/0x221
[<c203a204>] ? process_one_work+0x12e/0x210
[<c203a5e4>] ? worker_thread+0x116/0x1ad
[<c203a4ce>] ? rescuer_thread+0x1cb/0x1cb
[<c203d8f5>] ? kthread+0x67/0x6c
[<c2457ebb>] ? ret_from_kernel_thread+0x1b/0x30
[<c203d88e>] ? init_completion+0x18/0x18
v2: Retire the locking in vlv_crtc_enable() and do it close to the meat.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Squash in a s/mutex_lock/mutex_unlock/ fixup spotted by the 0
day kernel build/coccinelle and reported by Dan Carpenter.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Usual drill applies. Again I've not switched the upcast helpers to use
intel_encoder instead of drm_encoder since that's much more invasive
and will change also the hdmi and ddi encoders.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The w/a db makes the recommendation to both use a non-default value for
the initial clock and then to retry with an alternative clock for
Haswell with the Lakeport PCH.
"On LPT:H, use a divider value of 63 decimal (03Fh). If there is a
failure, retry at least three times with 63, then retry at least three
times with 72 decimal (048h)."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to decypher detection failures is a little tricker at the moment as
the only indicator of progress is when output_poll_execute() tells us
the result after the connector->detect() has run. This patch adds a
telltale to the start of each detect function so that we can track
progress and associate activity more clearly with each connector.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Restore debug message lost in merge commit e1b73cba13. Also clarify it
that we are only clamping bpp not overwriting it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required function to disable PSR when going to console mode.
But also can be used whenever PSR mode entry conditions changed.
v2: Add it before PSR Hook. Update function not really been called yet.
v3: Fix coding style detected by checkpatch by Paulo Zanoni.
v4: do_enable must be static as Paulo noticed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: prefer seq_puts to seq_printf detected by Paulo Zanoni.
v3: PSR is disabled by default. Without userspace ready it
will cause regression for kde and xdm users
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: reuse of just created is_edp_psr and put it at right place.
v3: move is_edp_psr above intel_edp_disable
v4: remove parentheses. Noticed by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP 1.2 compatible displays may report a 5.4Gbps maximum bandwidth which
the driver will treat as an invalid value and use 1.62Gbps instead. Fix
this by capping to 2.7Gbps for sinks reporting a 5.4Gbps max bw.
Also add a warning for reserved values.
v2:
- allow only bw values explicitly listed in the DP standard (Daniel,
Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for comparing modes between configuration changes.
The tricky part is to allow us to reuse the new get_clock stuff to
recover the lvds clock on gen2/3 when neither the vbt has an lvds mode
nor the panel a (useful) EDID.
v2: try harder to calulate non-simple pixel clocks (Daniel)
call get_clock after getting the encoder config, needed for pixel multiply
(Jesse)
v3: drop get_clock now that the pixel_multiply has been moved into
get_pipe_config
v4: re-add get_clock; we need to get the pixel multiplier in the
encoder, so need to calculate the clock value after the encoder's
get_config is called
v5: drop hsw clock_get, still needs to be written
v6: add fuzzy clock check (Daniel)
v7: wrap fuzzy clock check under !IS_HASWELL
use port_clock field rather than a new CPU eDP clock field in crtc_config
v8: remove stale pixel_multiplier sets (Daniel)
multiply by pixel_multiplier in 9xx clock get too (Daniel)
v9: make sure we set pixel_multiplier before calling clock_get from mode_get
for LVDS (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add some explanation to the commit message about why we have
to jump through a few hoops. Also remove the rebase-fail hunk from
intel_sdvo.c]
[danvet: Squash in the fixup from Jesse to also call ->get_clock in
the modeset state checker.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On DevCPT, the control register for Transcoder DP Sync Polarity is
TRANS_DP_CTL, not DP_CTL.
Without this patch, Many call trace occur on CPT machine with DP monitor.
The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X)
v2: use intel-crtc to simple patch, suggested by Daniel.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[danvet: Extend the encoder->get_config comment to specify that we now
also depend upon intel_encoder->base.crtc being correct. Also bikeshed
s/intel_crtc/crtc/.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.
This has annoyed me for a long time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've been ignoring this return value, so print a nice backtrace in
case it's not what we expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.
On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder
And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.
On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector
And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:
commit 21a8e6a485
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 10 23:28:35 2013 +0200
drm/i915: don't setup hdmi for port D edp in ddi_init
So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_dp_init_connector is too big for my poor little brain.
No functional changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time we call intel_dp_destroy (which destroys the connector)
the encoder may have been destroyed already, so if we use it we may be
reading some free memory. That happens in drm_mode_config_cleanup()
and also inside intel_dp_init_connector() when we detect a ghost eDP.
I also hope this may solve some random memory bugs.
Reported by kmemcheck.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.
Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
readout and cross-checking (this shuts up the confused pch pll refcount
WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully
* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: remove a superflous semi-colon
drm/i915: Kill useless "Enable panel fitter" comments
drm/i915: Remove extra "ring" from error message
drm/i915: simplify the reduced clock handling for pch plls
drm/i915: stop killing pfit on i9xx
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
drm/i915: set up PIPECONF explicitly on ilk-ivb
drm/i915: find guilty batch buffer on ring resets
drm/i915: store ring hangcheck action
drm/i915: add batch bo to i915_add_request()
drm/i915: change i915_add_request to macro
drm/i915: add i915_gem_context_get_hang_stats()
drm/i915: add struct i915_ctx_hang_stats
drm/i915: Try harder to disable trickle feed on VLV
drm/i915: fix up pch pll enabling for pixel multipliers
drm/i915: hw state readout and cross-checking for shared dplls
drm/i915: WARN on lack of shared dpll
drm/i915: split up intel_modeset_check_state
drm/i915: extract readout_hw_state from setup_hw_state
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c
Daniel writes:
Another round of drm-intel-next for 3.11. Highlights:
- Haswell IPS support (Paulo Zanoni)
- VECS support on Haswell (Ben Widawsky, Xiang Haihao, ...)
- Haswell watermark fixes (Paulo Zanoni)
- "Make the gun bigger again" multithread fence fix from Chris.
- i915_error_state finnally no longer fails with -ENOMEM! Big thanks to
Mika for tackling this.
- vlv sideband locking fixes from Jani
- Hangcheck prep work for arb_robustness support (Mika&Chris)
- edp vs cpu port confusion clean-up from Imre
- pile of smaller fixes and cleanups all over.
* tag 'drm-intel-next-2013-06-01' of git://people.freedesktop.org/~danvet/drm-intel: (70 commits)
drm/i915: add i915_ips_status debugfs entry
drm/i915: add enable_ips module option
drm/i915: implement IPS feature
drm/i915: fix up the edp power well check
drm/i915: add I915_PARAM_HAS_VEBOX to i915_getparam
drm/i915: add I915_EXEC_VEBOX to i915_gem_do_execbuffer()
drm/i915: add VEBOX into debugfs
drm/i915: Enable vebox interrupts
drm/i915: vebox interrupt get/put
drm/i915: consolidate interrupt naming scheme
drm/i915: Convert irq_refounct to struct
drm/i915: make PM interrupt writes non-destructive
drm/i915: Add PM regs to pre/post install
drm/i915: Create an ivybridge_irq_preinstall
drm/i915: Create a more generic pm handler for hsw+
drm/i915: add support for 5/6 data buffer partitioning on Haswell
drm/i915: properly set HSW WM_LP watermarks
drm/i915: properly set HSW WM_PIPE registers
drm/i915: fix pch_nop support
drm/i915: Vebox ringbuffer init
...
We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280
Tested-by: shui yangwei <yangweix.shui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prepares a bit for the next big patch, where we switch the
semantics of the different clocks in the pipe config around.
Since I've broken cpu eDP PLL handling in the first version I've
figured some refactoring is in order.
Split out on request from Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch changes all remaining is_cpu_edp() check with a check for port
A. We can do this, since in all these cases ValleyView is handled
separately and port A is always a CPU side eDP port.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ValleyView for both eDP and DP the AUX input clock is 200MHz, so we
can calculate for both the clock divider for the 2MHz target rate at the
same place. Afterwards we can also replace the is_cpu_edp() check with a
check for port A.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on 3739850b46 - "drm/i915: disable the cpu edp port after the
cpu pipe" and the bspec disabling sequence for IVB and older it seems we
have to distinguish only the CPU vs. PCH port case, whether it's a DP or
eDP doesn't seem to matter. For IVB and older on the CPU side we can
only have eDP on port A, DP ports can only be on the PCH side. On VLV we
have only CPU side eDP/DP ports, no PCH. So the condition for the
disabling sequence we need for CPU ports is port == A || IS_VLV.
This allows us to remove is_cpu_edp() completely in a later patch.
v2:
- simplify (and fix) the condition for CPU side ports and adjust the
commit message accordingly (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Highlights (copy-pasted from my testing cycle mails):
- fbc support for Haswell (Rodrigo)
- streamlined workaround comments, including an igt tool to grep for
them (Damien)
- sdvo and TV out cleanups, including a fixup for sdvo multifunction devices
- refactor our eDP mess a bit (Imre)
- don't register the hdmi connector on haswell when desktop eDP is present
- vlv support is no longer preliminary!
- more vlv fixes from Jesse for stolen and dpll handling
- more flexible power well checking infrastructure from Paulo
- a few gtt patches from Ben
- a bit of OCD cleanups for transcoder #defines and an assorted pile
of smaller things.
- fixes for the gmch modeset sequence
- a bit of OCD around plane/pipe usage (Ville)
- vlv turbo support (Jesse)
- tons of vlv modeset fixes (Jesse et al.)
- vlv pte write fixes (Kenneth Graunke)
- hpd filtering to avoid costly probes on unaffected outputs (Egbert Eich)
- intel dev_info cleanups and refactorings (Damien)
- vlv rc6 support (Jesse)
- random pile of fixes around non-24bpp modes handling
- asle/opregion cleanups and locking fixes (Jani)
- dp dpll refactoring
- improvements for reduced_clock computation on g4x/ilk+
- pfit state refactored to use pipe_config (Jesse)
- lots more computed modeset state moved to pipe_config, including readout
and cross-check support
- fdi auto-dithering for ivb B/C links, using the neat pipe_config
improvements
- drm_rect helpers plus sprite clipping fixes (Ville)
- hw context refcounting (Mika + Ben)
* tag 'drm-intel-next-2013-05-20-merged' of git://people.freedesktop.org/~danvet/drm-intel: (155 commits)
drm/i915: add support for dvo Chrontel 7010B
drm/i915: Use pipe config state to control gmch pfit enable/disable
drm/i915: Use pipe_config state to disable ilk+ pfit
drm/i915: panel fitter hw state readout&check support
drm/i915: implement WADPOClockGatingDisable for LPT
drm/i915: Add missing platform tags to FBC workaround comments
drm/i915: rip out an unused lvds_reg variable
drm/i915: Compute WR PLL dividers dynamically
drm/i915: HSW FBC WaFbcDisableDpfcClockGating
drm/i915: HSW FBC WaFbcAsynchFlipDisableFbcQueue
drm/i915: Enable FBC at Haswell.
drm/i915: IVB FBC WaFbcDisableDpfcClockGating
drm/i915: IVB FBC WaFbcAsynchFlipDisableFbcQueue
drm/i915: Add support for FBC on Ivybridge.
drm/i915: Organize VBT stuff inside drm_i915_private
drm/i915: make SDVO TV-out work for multifunction devices
drm/i915: rip out now unused is_foo tracking from crtc code
drm/i915: rip out TV-out lore ...
drm/i915: drop TVclock special casing on ilk+
drm/i915: move sdvo TV clock computation to intel_sdvo.c
...
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During DP AUX communication we might time out 1 jiffy too early, because
the calculated expiry jiffy value is one less than needed.
This is only one reason for false DP AUX timeouts. For a complete
solution we also need the following fix, which is now queued for
mainline: http://marc.info/?l=linux-kernel&m=136748515710837&w=2
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this, that 338 can finally become the correct 337500.
Due to the change we need to adjust the intel_dp_aux_ch function to
set the correct value, so adjust the division and also use
DIV_ROUND_CLOSEST instead of the old "round down" behavior because the
spec says the value "should be programmed to get as close as possible
to the ideal rate of 2MHz".
Quoting Paulo's follow-up to a question from Chris Wilson to explain
what exactly will change:
I use the 337500 value on the next patch, when setting the
ips_linetime value. The correct frequency is 337500, not 338000.
ips_linetime = DIV_ROUND_CLOSEST(mode->htotal * 1000 * 8,
intel_ddi_get_cdclk_freq);
For a mode with htotal of 2640 [0] we'll have: (i) (2640 * 1000 * 8) /
338000 = 62.48, resulting in 62 and (ii) (2640 * 1000 * 8) / 337500 =
62.57 resulting in 63.
For the case inside intel_dp.c:
Previously we were using 338. So with the old formula we were writing
338/2 = 169 to the register. And 337500 / 169 = 1997.04 (we use 337500
here because it's the real clock value). With the new value of
337500/2000 we'll have 168.75, which is 168 on the round-down case and
169 on the round-closest case. If we write 168 to the register, 337500
/ 168 = 2008.92, and 2008.92 is more distant from 2000 than 1997.04.
So with this patch we're changing the formula but still writing the
same correct value to the DP AUX register.
[0]: That's 1920x1080@50Hz on my DP monitor.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp the commit message with Paulo's follow-up.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.
Just used for mode flags atm, so we can check the pipe config state at
mode set time.
v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
correct command used (Ville)
remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Just a few straggling fixes I hoovered up, and an intel fixes pull
from Daniel which fixes some regressions, and some mgag200 fixes from
Matrox."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/mgag200: Fix framebuffer base address programming
drm/mgag200: Convert counter delays to jiffies
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
drm/mgag200: Don't change unrelated registers during modeset
drm: Only print a debug message when the polled connector has changed
drm: Make the HPD status updates debug logs more readable
drm: Use names of ioctls in debug traces
drm: Remove pointless '-' characters from drm_fb_helper documentation
drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
drm: refactor call to request_module
drm: Don't prune modes loudly when a connector is disconnected
drm: Add missing break in the command line mode parsing code
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
drm_i915_private is getting bigger and bigger when adding new vbt stuff.
So, the better way of getting drm_i915_private organized is to create
a special structure for vbt stuff.
v2: Basically conflicts fixes
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users for these, so remove them.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
is_pch_edp() will be removed by the next patch, so replace it by a check
for the port and device type.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
is_pch_edp() will be removed in a follow-up patch, so replace it
with a check for the port and VBT info (for port-D eDP).
Also make things a bit clearer by using a switch on the ports.
v2:
- make the comment about not setting the conder type for DP clearer
(Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
A few intel fixes for smaller issues and one revert for an sdv hack which
we've wanted to kill anyway. Plus two drm patches included for your
convenience, both regression fixers for mine own screw-ups.
+ both fixes for stolen mem handling.
* 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
